From: Giuseppe Barba <giuseppe.barba@st.com>
To: <linux-iio@vger.kernel.org>
Cc: <denis.ciocca@st.com>, <jic23@kernel.org>,
Giuseppe Barba <giuseppe.barba@st.com>
Subject: [PATCH V2 5/5] iio: st-magn: add support for lsm303agr magnetometer
Date: Mon, 20 Jul 2015 16:20:29 +0200 [thread overview]
Message-ID: <1437402029-29786-6-git-send-email-giuseppe.barba@st.com> (raw)
In-Reply-To: <1437402029-29786-1-git-send-email-giuseppe.barba@st.com>
This adds support for the lsm303agr magnetometer.
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
---
.../devicetree/bindings/iio/st-sensors.txt | 1 +
drivers/iio/magnetometer/st_magn.h | 1 +
drivers/iio/magnetometer/st_magn_core.c | 82 ++++++++++++++++++++++
drivers/iio/magnetometer/st_magn_i2c.c | 5 ++
drivers/iio/magnetometer/st_magn_spi.c | 1 +
5 files changed, 90 insertions(+)
diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt
index d80bdaa..d3ccdb1 100644
--- a/Documentation/devicetree/bindings/iio/st-sensors.txt
+++ b/Documentation/devicetree/bindings/iio/st-sensors.txt
@@ -47,6 +47,7 @@ Gyroscopes:
- st,lsm330-gyro
Magnetometers:
+- st,lsm303agr-magn
- st,lsm303dlh-magn
- st,lsm303dlhc-magn
- st,lsm303dlm-magn
diff --git a/drivers/iio/magnetometer/st_magn.h b/drivers/iio/magnetometer/st_magn.h
index 60441023..06a4d9c 100644
--- a/drivers/iio/magnetometer/st_magn.h
+++ b/drivers/iio/magnetometer/st_magn.h
@@ -18,6 +18,7 @@
#define LSM303DLHC_MAGN_DEV_NAME "lsm303dlhc_magn"
#define LSM303DLM_MAGN_DEV_NAME "lsm303dlm_magn"
#define LIS3MDL_MAGN_DEV_NAME "lis3mdl"
+#define LSM303AGR_MAGN_DEV_NAME "lsm303agr_magn"
int st_magn_common_probe(struct iio_dev *indio_dev);
void st_magn_common_remove(struct iio_dev *indio_dev);
diff --git a/drivers/iio/magnetometer/st_magn_core.c b/drivers/iio/magnetometer/st_magn_core.c
index 4c0cef8..f8dc4b8 100644
--- a/drivers/iio/magnetometer/st_magn_core.c
+++ b/drivers/iio/magnetometer/st_magn_core.c
@@ -43,6 +43,7 @@
#define ST_MAGN_FS_AVL_8000MG 8000
#define ST_MAGN_FS_AVL_8100MG 8100
#define ST_MAGN_FS_AVL_12000MG 12000
+#define ST_MAGN_FS_AVL_15000MG 15000
#define ST_MAGN_FS_AVL_16000MG 16000
/* CUSTOM VALUES FOR SENSOR 0 */
@@ -157,6 +158,29 @@
#define ST_MAGN_2_OUT_Y_L_ADDR 0x2a
#define ST_MAGN_2_OUT_Z_L_ADDR 0x2c
+/* CUSTOM VALUES FOR SENSOR 3 */
+#define ST_MAGN_3_WAI_ADDR 0x4f
+#define ST_MAGN_3_WAI_EXP 0x40
+#define ST_MAGN_3_ODR_ADDR 0x60
+#define ST_MAGN_3_ODR_MASK 0x0c
+#define ST_MAGN_3_ODR_AVL_10HZ_VAL 0x00
+#define ST_MAGN_3_ODR_AVL_20HZ_VAL 0x01
+#define ST_MAGN_3_ODR_AVL_50HZ_VAL 0x02
+#define ST_MAGN_3_ODR_AVL_100HZ_VAL 0x03
+#define ST_MAGN_3_PW_ADDR 0x60
+#define ST_MAGN_3_PW_MASK 0x03
+#define ST_MAGN_3_PW_ON 0x00
+#define ST_MAGN_3_PW_OFF 0x03
+#define ST_MAGN_3_BDU_ADDR 0x62
+#define ST_MAGN_3_BDU_MASK 0x10
+#define ST_MAGN_3_DRDY_IRQ_ADDR 0x62
+#define ST_MAGN_3_DRDY_INT_MASK 0x01
+#define ST_MAGN_3_FS_AVL_15000_GAIN 1500
+#define ST_MAGN_3_MULTIREAD_BIT false
+#define ST_MAGN_3_OUT_X_L_ADDR 0x68
+#define ST_MAGN_3_OUT_Y_L_ADDR 0x6a
+#define ST_MAGN_3_OUT_Z_L_ADDR 0x6c
+
static const struct iio_chan_spec st_magn_16bit_channels[] = {
ST_SENSORS_LSM_CHANNELS(IIO_MAGN,
BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
@@ -189,6 +213,22 @@ static const struct iio_chan_spec st_magn_2_16bit_channels[] = {
IIO_CHAN_SOFT_TIMESTAMP(3)
};
+static const struct iio_chan_spec st_magn_3_16bit_channels[] = {
+ ST_SENSORS_LSM_CHANNELS(IIO_MAGN,
+ BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+ ST_SENSORS_SCAN_X, 1, IIO_MOD_X, 's', IIO_LE, 16, 16,
+ ST_MAGN_3_OUT_X_L_ADDR),
+ ST_SENSORS_LSM_CHANNELS(IIO_MAGN,
+ BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+ ST_SENSORS_SCAN_Y, 1, IIO_MOD_Y, 's', IIO_LE, 16, 16,
+ ST_MAGN_3_OUT_Y_L_ADDR),
+ ST_SENSORS_LSM_CHANNELS(IIO_MAGN,
+ BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+ ST_SENSORS_SCAN_Z, 1, IIO_MOD_Z, 's', IIO_LE, 16, 16,
+ ST_MAGN_3_OUT_Z_L_ADDR),
+ IIO_CHAN_SOFT_TIMESTAMP(3)
+};
+
static const struct st_sensor_settings st_magn_sensors_settings[] = {
{
.wai = 0, /* This sensor has no valid WhoAmI report 0 */
@@ -402,6 +442,48 @@ static const struct st_sensor_settings st_magn_sensors_settings[] = {
.multi_read_bit = ST_MAGN_2_MULTIREAD_BIT,
.bootime = 2,
},
+ {
+ .wai = ST_MAGN_3_WAI_EXP,
+ .wai_addr = ST_MAGN_3_WAI_ADDR,
+ .sensors_supported = {
+ [0] = LSM303AGR_MAGN_DEV_NAME,
+ },
+ .ch = (struct iio_chan_spec *)st_magn_3_16bit_channels,
+ .odr = {
+ .addr = ST_MAGN_3_ODR_ADDR,
+ .mask = ST_MAGN_3_ODR_MASK,
+ .odr_avl = {
+ { 10, ST_MAGN_3_ODR_AVL_10HZ_VAL, },
+ { 20, ST_MAGN_3_ODR_AVL_20HZ_VAL, },
+ { 50, ST_MAGN_3_ODR_AVL_50HZ_VAL, },
+ { 100, ST_MAGN_3_ODR_AVL_100HZ_VAL, },
+ },
+ },
+ .pw = {
+ .addr = ST_MAGN_3_PW_ADDR,
+ .mask = ST_MAGN_3_PW_MASK,
+ .value_on = ST_MAGN_3_PW_ON,
+ .value_off = ST_MAGN_3_PW_OFF,
+ },
+ .fs = {
+ .fs_avl = {
+ [0] = {
+ .num = ST_MAGN_FS_AVL_15000MG,
+ .gain = ST_MAGN_3_FS_AVL_15000_GAIN,
+ },
+ },
+ },
+ .bdu = {
+ .addr = ST_MAGN_3_BDU_ADDR,
+ .mask = ST_MAGN_3_BDU_MASK,
+ },
+ .drdy_irq = {
+ .addr = ST_MAGN_3_DRDY_IRQ_ADDR,
+ .mask_int1 = ST_MAGN_3_DRDY_INT_MASK,
+ },
+ .multi_read_bit = ST_MAGN_3_MULTIREAD_BIT,
+ .bootime = 2,
+ },
};
static int st_magn_read_raw(struct iio_dev *indio_dev,
diff --git a/drivers/iio/magnetometer/st_magn_i2c.c b/drivers/iio/magnetometer/st_magn_i2c.c
index 28aa807..8aa37af 100644
--- a/drivers/iio/magnetometer/st_magn_i2c.c
+++ b/drivers/iio/magnetometer/st_magn_i2c.c
@@ -36,6 +36,10 @@ static const struct of_device_id st_magn_of_match[] = {
.compatible = "st,lis3mdl-magn",
.data = LIS3MDL_MAGN_DEV_NAME,
},
+ {
+ .compatible = "st,lsm303agr-magn",
+ .data = LSM303AGR_MAGN_DEV_NAME,
+ },
{},
};
MODULE_DEVICE_TABLE(of, st_magn_of_match);
@@ -79,6 +83,7 @@ static const struct i2c_device_id st_magn_id_table[] = {
{ LSM303DLHC_MAGN_DEV_NAME },
{ LSM303DLM_MAGN_DEV_NAME },
{ LIS3MDL_MAGN_DEV_NAME },
+ { LSM303AGR_MAGN_DEV_NAME },
{},
};
MODULE_DEVICE_TABLE(i2c, st_magn_id_table);
diff --git a/drivers/iio/magnetometer/st_magn_spi.c b/drivers/iio/magnetometer/st_magn_spi.c
index 7adacf1..0abca2c 100644
--- a/drivers/iio/magnetometer/st_magn_spi.c
+++ b/drivers/iio/magnetometer/st_magn_spi.c
@@ -51,6 +51,7 @@ static const struct spi_device_id st_magn_id_table[] = {
{ LSM303DLHC_MAGN_DEV_NAME },
{ LSM303DLM_MAGN_DEV_NAME },
{ LIS3MDL_MAGN_DEV_NAME },
+ { LSM303AGR_MAGN_DEV_NAME },
{},
};
MODULE_DEVICE_TABLE(spi, st_magn_id_table);
--
1.9.1
prev parent reply other threads:[~2015-07-20 14:20 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-07-20 14:20 [PATCH V2 0/5] Added ST LSM303AGR sensor Giuseppe Barba
2015-07-20 14:20 ` [PATCH V2 1/5] iio: st-sensors: add configuration for WhoAmI address Giuseppe Barba
2015-07-21 3:51 ` Denis Ciocca
2015-07-21 7:33 ` Giuseppe BARBA
2015-07-20 14:20 ` [PATCH V2 2/5] iio: st-sensors: add support for single full scale device Giuseppe Barba
2015-07-20 14:20 ` [PATCH V2 3/5] iio: st_magn: Add irq trigger handling Giuseppe Barba
2015-07-20 14:20 ` [PATCH V2 4/5] iio: st-accel: add support for lsm303agr accelerometer Giuseppe Barba
2015-07-20 14:20 ` Giuseppe Barba [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1437402029-29786-6-git-send-email-giuseppe.barba@st.com \
--to=giuseppe.barba@st.com \
--cc=denis.ciocca@st.com \
--cc=jic23@kernel.org \
--cc=linux-iio@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).