[PATCH v2] ARM: dts: ux500: configure the accelerometers open drain

[Linus Walleij <linus.walleij@linaro.org>]

Configure the two accelerometers sharing GPIO line 82 as:

- Open drain so that they can share the same interrupt line.

Configure the corresponding interrupt pin:

- Trigger on the falling edge since open drain implies that we
  do not actively drive the line high, but we will actively drive
  it low to generate interrupts and then it moves from high to low
  i.e. a falling edge.

- Pulled up so the line will be biased to high unless an IRQ
  is active on any device on the line, and thus it goes high
  again after the interrupt is deasserted.

Cc: linux-iio@vger.kernel.org
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v1->v2:
- Switch to using the drive-mode-open-drain; setting
---
 arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
index 55f9d0cc90f3..aec816c8ecb6 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
@@ -93,14 +93,15 @@
 				/* Accelerometer */
 				compatible = "st,lsm303dlh-accel";
 				st,drdy-int-pin = <1>;
+				drive-open-drain;
 				reg = <0x18>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
 				vddio-supply = <&db8500_vsmps2_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&accel_tvk_mode>;
 				interrupt-parent = <&gpio2>;
-				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
-					     <19 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
+					     <19 IRQ_TYPE_EDGE_FALLING>;
 			};
 			lsm303dlh@1e {
 				/*
@@ -118,14 +119,15 @@
 				/* Accelerometer */
 				compatible = "st,lis331dl-accel";
 				st,drdy-int-pin = <1>;
+				drive-open-drain;
 				reg = <0x1c>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
 				vddio-supply = <&db8500_vsmps2_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&accel_tvk_mode>;
 				interrupt-parent = <&gpio2>;
-				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
-					     <19 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
+					     <19 IRQ_TYPE_EDGE_FALLING>;
 			};
 			ak8974@0f {
 				/* Magnetometer */
@@ -216,7 +218,7 @@
 					/* Accelerometer interrupt lines 1 & 2 */
 					tvk_cfg {
 						pins = "GPIO82_C1", "GPIO83_D3";
-						ste,config = <&gpio_in_pd>;
+						ste,config = <&gpio_in_pu>;
 					};
 				};
 			};
-- 
2.4.3