From: Linus Walleij <linus.walleij@linaro.org>
To: Jonathan Cameron <jic23@kernel.org>,
linux-iio@vger.kernel.org, Akinobu Mita <akinobu.mita@gmail.com>,
"H. Nikolaus Schaller" <hns@goldelico.com>,
Matt Ranostay <mranostay@gmail.com>
Cc: Christoph Mair <christoph.mair@gmail.com>,
Vlad Dogaru <vlad.dogaru@intel.com>,
Hartmut Knaack <knaack.h@gmx.de>,
Marek Belisko <marek@goldelico.com>,
Eric Andersson <eric.andersson@unixphere.com>,
Neil Brown <neilb@suse.de>,
Linus Walleij <linus.walleij@linaro.org>,
devicetree@vger.kernel.org
Subject: [PATCH 01/10 v3] iio: pressure: bmp280: augment DT bindings
Date: Mon, 27 Jun 2016 18:30:11 +0200 [thread overview]
Message-ID: <1467045020-2665-2-git-send-email-linus.walleij@linaro.org> (raw)
In-Reply-To: <1467045020-2665-1-git-send-email-linus.walleij@linaro.org>
This adds standard device tree bindings for a reset GPIO line, and
the VDDD and VDDA power regulators.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLov v2->v3:
- None, just resending in case Jonathan prefers this binding doc
ChangeLog v1->v2:
- Order compatible string on single lines
- Add "bosch,bme280" for the new sensor from Matt
---
Documentation/devicetree/bindings/iio/pressure/bmp085.txt | 15 +++++++++++++--
1 file changed, 13 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt
index d7a6deb6b21e..c7198a03c906 100644
--- a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt
+++ b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt
@@ -1,7 +1,11 @@
-BMP085/BMP18x digital pressure sensors
+BMP085/BMP18x/BMP28x digital pressure sensors
Required properties:
-- compatible: bosch,bmp085
+- compatible: must be one of:
+ "bosch,bmp085"
+ "bosch,bmp180"
+ "bosch,bmp280"
+ "bosch,bme280"
Optional properties:
- chip-id: configurable chip id for non-default chip revisions
@@ -10,6 +14,10 @@ Optional properties:
value range is 0-3 with rising sensitivity.
- interrupt-parent: should be the phandle for the interrupt controller
- interrupts: interrupt mapping for IRQ
+- reset-gpios: a GPIO line handling reset of the sensor: as the line is
+ active low, it should be marked GPIO_ACTIVE_LOW (see gpio/gpio.txt)
+- vddd-supply: digital voltage regulator (see regulator/regulator.txt)
+- vdda-supply: analog voltage regulator (see regulator/regulator.txt)
Example:
@@ -21,4 +29,7 @@ pressure@77 {
default-oversampling = <2>;
interrupt-parent = <&gpio0>;
interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+ reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ vddd-supply = <&foo>;
+ vdda-supply = <&bar>;
};
--
2.4.11
next prev parent reply other threads:[~2016-06-27 16:30 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-27 16:30 [PATCH 00/10] Improve the BMP280 driver v3 Linus Walleij
2016-06-27 16:30 ` Linus Walleij [this message]
2016-06-27 16:30 ` [PATCH 02/10 v3] iio: pressure: bmp280: support device tree initialization Linus Walleij
2016-06-27 16:30 ` [PATCH 03/10 v3] iio: pressure: bmp280: add reset GPIO line handling Linus Walleij
2016-06-27 16:52 ` Peter Meerwald-Stadler
2016-06-27 17:05 ` Linus Walleij
2016-06-29 17:45 ` Jonathan Cameron
2016-06-29 19:00 ` Linus Walleij
2016-06-27 16:30 ` [PATCH 04/10 v3] iio: pressure: bmp280: support supply regulators Linus Walleij
2016-06-27 16:56 ` Peter Meerwald-Stadler
2016-06-27 16:30 ` [PATCH 05/10 v3] iio: pressure: bmp280: split driver in logical parts Linus Walleij
2016-06-28 13:43 ` Akinobu Mita
2016-06-27 16:30 ` [PATCH 06/10 v3] iio: pressure: bmp280: split off an I2C Kconfig entry Linus Walleij
2016-06-27 16:30 ` [PATCH 07/10 v3] iio: pressure: bmp280: add SPI interface driver Linus Walleij
2016-06-27 17:06 ` Peter Meerwald-Stadler
2016-06-29 14:35 ` Linus Walleij
2016-06-27 16:30 ` [PATCH 08/10 v3] iio: pressure: bmp280: add support for BMP085 EOC interrupt Linus Walleij
2016-06-27 16:30 ` [PATCH 09/10 v3] iio: pressure: bmp280: read calibration data once Linus Walleij
2016-06-27 17:01 ` Peter Meerwald-Stadler
2016-06-27 16:30 ` [PATCH 10/10 v3] iio: pressure: bmp280: add power management Linus Walleij
2016-06-27 17:09 ` Peter Meerwald-Stadler
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1467045020-2665-2-git-send-email-linus.walleij@linaro.org \
--to=linus.walleij@linaro.org \
--cc=akinobu.mita@gmail.com \
--cc=christoph.mair@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=eric.andersson@unixphere.com \
--cc=hns@goldelico.com \
--cc=jic23@kernel.org \
--cc=knaack.h@gmx.de \
--cc=linux-iio@vger.kernel.org \
--cc=marek@goldelico.com \
--cc=mranostay@gmail.com \
--cc=neilb@suse.de \
--cc=vlad.dogaru@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).