From: Jonathan Cameron <jic23@kernel.org>
To: Sean Nyekjaer <sean@geanix.com>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>,
linux-iio@vger.kernel.org, martin@geanix.com,
rjones@gateworks.com, lorenzo.bianconi@redhat.com,
devicetree@vger.kernel.org
Subject: Re: [PATCH 03/13] iio: imu: st_lsm6dsx: move irq related definitions in irq_config
Date: Sat, 12 Oct 2019 13:13:04 +0100 [thread overview]
Message-ID: <20191012131304.321f7240@archlinux> (raw)
In-Reply-To: <6656913c-9b1b-3f8e-a88e-a050dd717ba3@geanix.com>
On Mon, 7 Oct 2019 09:54:55 +0200
Sean Nyekjaer <sean@geanix.com> wrote:
> On 06/10/2019 15.21, Lorenzo Bianconi wrote:
> > Group irq related definition in irq_config structure in
> > st_lsm6dsx_settings. This is a preliminary patch to move
> > OpenDrain/Active low registers in st_lsm6dsx_settings.
> >
> > Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
> Tested-by: Sean Nyekjaer <sean@geanix.com>
Applied to the togreg branch of iio.git and pushed out as testing for
the autobuilders to play with it.
Thanks,
Jonathan
> > ---
> > drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 22 +-
> > drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 265 ++++++++++++-------
> > 2 files changed, 179 insertions(+), 108 deletions(-)
> >
> > diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
> > index fd02d0e184f3..873ec3b8fd69 100644
> > --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
> > +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
> > @@ -236,29 +236,21 @@ struct st_lsm6dsx_ext_dev_settings {
> > /**
> > * struct st_lsm6dsx_settings - ST IMU sensor settings
> > * @wai: Sensor WhoAmI default value.
> > - * @int1_addr: Control Register address for INT1
> > - * @int2_addr: Control Register address for INT2
> > * @reset_addr: register address for reset/reboot
> > * @max_fifo_size: Sensor max fifo length in FIFO words.
> > * @id: List of hw id/device name supported by the driver configuration.
> > * @channels: IIO channels supported by the device.
> > + * @irq_config: interrupts related registers.
> > * @odr_table: Hw sensors odr table (Hz + val).
> > * @fs_table: Hw sensors gain table (gain + val).
> > * @decimator: List of decimator register info (addr + mask).
> > * @batch: List of FIFO batching register info (addr + mask).
> > - * @lir: Latched interrupt register info (addr + mask).
> > - * @clear_on_read: Clear on read register info (addr + mask).
> > * @fifo_ops: Sensor hw FIFO parameters.
> > * @ts_settings: Hw timer related settings.
> > * @shub_settings: i2c controller related settings.
> > */
> > struct st_lsm6dsx_settings {
> > u8 wai;
> > - u8 int1_addr;
> > - u8 int2_addr;
> > - u8 int1_func_addr;
> > - u8 int2_func_addr;
> > - u8 int_func_mask;
> > u8 reset_addr;
> > u16 max_fifo_size;
> > struct {
> > @@ -269,12 +261,18 @@ struct st_lsm6dsx_settings {
> > const struct iio_chan_spec *chan;
> > int len;
> > } channels[2];
> > + struct {
> > + struct st_lsm6dsx_reg irq1;
> > + struct st_lsm6dsx_reg irq2;
> > + struct st_lsm6dsx_reg irq1_func;
> > + struct st_lsm6dsx_reg irq2_func;
> > + struct st_lsm6dsx_reg lir;
> > + struct st_lsm6dsx_reg clear_on_read;
> > + } irq_config;
> > struct st_lsm6dsx_odr_table_entry odr_table[2];
> > struct st_lsm6dsx_fs_table_entry fs_table[2];
> > struct st_lsm6dsx_reg decimator[ST_LSM6DSX_MAX_ID];
> > struct st_lsm6dsx_reg batch[ST_LSM6DSX_MAX_ID];
> > - struct st_lsm6dsx_reg lir;
> > - struct st_lsm6dsx_reg clear_on_read;
> > struct st_lsm6dsx_fifo_ops fifo_ops;
> > struct st_lsm6dsx_hw_ts_settings ts_settings;
> > struct st_lsm6dsx_shub_settings shub_settings;
> > @@ -359,9 +357,9 @@ struct st_lsm6dsx_hw {
> > u8 ts_sip;
> > u8 sip;
> >
> > + const struct st_lsm6dsx_reg *irq_routing;
> > u8 event_threshold;
> > u8 enable_event;
> > - struct st_lsm6dsx_reg irq_routing;
> >
> > u8 *buff;
> >
> > diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
> > index eac695663b6f..23d67caa24ed 100644
> > --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
> > +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
> > @@ -61,7 +61,6 @@
> >
> > #include "st_lsm6dsx.h"
> >
> > -#define ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK BIT(3)
> > #define ST_LSM6DSX_REG_WHOAMI_ADDR 0x0f
> > #define ST_LSM6DSX_REG_RESET_MASK BIT(0)
> > #define ST_LSM6DSX_REG_BOOT_MASK BIT(7)
> > @@ -97,8 +96,6 @@ static const struct iio_chan_spec st_lsm6ds0_gyro_channels[] = {
> > static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > {
> > .wai = 0x68,
> > - .int1_addr = 0x0c,
> > - .int2_addr = 0x0d,
> > .reset_addr = 0x22,
> > .max_fifo_size = 32,
> > .id = {
> > @@ -164,14 +161,19 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .fs_avl[2] = { IIO_DEGREE_TO_RAD(2000), 0x3 },
> > },
> > },
> > + .irq_config = {
> > + .irq1 = {
> > + .addr = 0x0c,
> > + .mask = BIT(3),
> > + },
> > + .irq2 = {
> > + .addr = 0x0d,
> > + .mask = BIT(3),
> > + },
> > + },
> > },
> > {
> > .wai = 0x69,
> > - .int1_addr = 0x0d,
> > - .int2_addr = 0x0e,
> > - .int1_func_addr = 0x5e,
> > - .int2_func_addr = 0x5f,
> > - .int_func_mask = BIT(5),
> > .reset_addr = 0x12,
> > .max_fifo_size = 1365,
> > .id = {
> > @@ -238,6 +240,28 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
> > },
> > },
> > + .irq_config = {
> > + .irq1 = {
> > + .addr = 0x0d,
> > + .mask = BIT(3),
> > + },
> > + .irq2 = {
> > + .addr = 0x0e,
> > + .mask = BIT(3),
> > + },
> > + .lir = {
> > + .addr = 0x58,
> > + .mask = BIT(0),
> > + },
> > + .irq1_func = {
> > + .addr = 0x5e,
> > + .mask = BIT(5),
> > + },
> > + .irq2_func = {
> > + .addr = 0x5f,
> > + .mask = BIT(5),
> > + },
> > + },
> > .decimator = {
> > [ST_LSM6DSX_ID_ACC] = {
> > .addr = 0x08,
> > @@ -248,10 +272,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .mask = GENMASK(5, 3),
> > },
> > },
> > - .lir = {
> > - .addr = 0x58,
> > - .mask = BIT(0),
> > - },
> > .fifo_ops = {
> > .update_fifo = st_lsm6dsx_update_fifo,
> > .read_fifo = st_lsm6dsx_read_fifo,
> > @@ -297,11 +317,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > },
> > {
> > .wai = 0x69,
> > - .int1_addr = 0x0d,
> > - .int2_addr = 0x0e,
> > - .int1_func_addr = 0x5e,
> > - .int2_func_addr = 0x5f,
> > - .int_func_mask = BIT(5),
> > .reset_addr = 0x12,
> > .max_fifo_size = 682,
> > .id = {
> > @@ -368,6 +383,28 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
> > },
> > },
> > + .irq_config = {
> > + .irq1 = {
> > + .addr = 0x0d,
> > + .mask = BIT(3),
> > + },
> > + .irq2 = {
> > + .addr = 0x0e,
> > + .mask = BIT(3),
> > + },
> > + .lir = {
> > + .addr = 0x58,
> > + .mask = BIT(0),
> > + },
> > + .irq1_func = {
> > + .addr = 0x5e,
> > + .mask = BIT(5),
> > + },
> > + .irq2_func = {
> > + .addr = 0x5f,
> > + .mask = BIT(5),
> > + },
> > + },
> > .decimator = {
> > [ST_LSM6DSX_ID_ACC] = {
> > .addr = 0x08,
> > @@ -378,10 +415,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .mask = GENMASK(5, 3),
> > },
> > },
> > - .lir = {
> > - .addr = 0x58,
> > - .mask = BIT(0),
> > - },
> > .fifo_ops = {
> > .update_fifo = st_lsm6dsx_update_fifo,
> > .read_fifo = st_lsm6dsx_read_fifo,
> > @@ -427,11 +460,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > },
> > {
> > .wai = 0x6a,
> > - .int1_addr = 0x0d,
> > - .int2_addr = 0x0e,
> > - .int1_func_addr = 0x5e,
> > - .int2_func_addr = 0x5f,
> > - .int_func_mask = BIT(5),
> > .reset_addr = 0x12,
> > .max_fifo_size = 682,
> > .id = {
> > @@ -507,6 +535,28 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
> > },
> > },
> > + .irq_config = {
> > + .irq1 = {
> > + .addr = 0x0d,
> > + .mask = BIT(3),
> > + },
> > + .irq2 = {
> > + .addr = 0x0e,
> > + .mask = BIT(3),
> > + },
> > + .lir = {
> > + .addr = 0x58,
> > + .mask = BIT(0),
> > + },
> > + .irq1_func = {
> > + .addr = 0x5e,
> > + .mask = BIT(5),
> > + },
> > + .irq2_func = {
> > + .addr = 0x5f,
> > + .mask = BIT(5),
> > + },
> > + },
> > .decimator = {
> > [ST_LSM6DSX_ID_ACC] = {
> > .addr = 0x08,
> > @@ -517,10 +567,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .mask = GENMASK(5, 3),
> > },
> > },
> > - .lir = {
> > - .addr = 0x58,
> > - .mask = BIT(0),
> > - },
> > .fifo_ops = {
> > .update_fifo = st_lsm6dsx_update_fifo,
> > .read_fifo = st_lsm6dsx_read_fifo,
> > @@ -570,8 +616,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > },
> > {
> > .wai = 0x6c,
> > - .int1_addr = 0x0d,
> > - .int2_addr = 0x0e,
> > .reset_addr = 0x12,
> > .max_fifo_size = 512,
> > .id = {
> > @@ -641,6 +685,24 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
> > },
> > },
> > + .irq_config = {
> > + .irq1 = {
> > + .addr = 0x0d,
> > + .mask = BIT(3),
> > + },
> > + .irq2 = {
> > + .addr = 0x0e,
> > + .mask = BIT(3),
> > + },
> > + .lir = {
> > + .addr = 0x56,
> > + .mask = BIT(0),
> > + },
> > + .clear_on_read = {
> > + .addr = 0x56,
> > + .mask = BIT(6),
> > + },
> > + },
> > .batch = {
> > [ST_LSM6DSX_ID_ACC] = {
> > .addr = 0x09,
> > @@ -651,14 +713,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .mask = GENMASK(7, 4),
> > },
> > },
> > - .lir = {
> > - .addr = 0x56,
> > - .mask = BIT(0),
> > - },
> > - .clear_on_read = {
> > - .addr = 0x56,
> > - .mask = BIT(6),
> > - },
> > .fifo_ops = {
> > .update_fifo = st_lsm6dsx_update_fifo,
> > .read_fifo = st_lsm6dsx_read_tagged_fifo,
> > @@ -711,11 +765,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > },
> > {
> > .wai = 0x6b,
> > - .int1_addr = 0x0d,
> > - .int2_addr = 0x0e,
> > - .int1_func_addr = 0x5e,
> > - .int2_func_addr = 0x5f,
> > - .int_func_mask = BIT(5),
> > .reset_addr = 0x12,
> > .max_fifo_size = 512,
> > .id = {
> > @@ -782,6 +831,32 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
> > },
> > },
> > + .irq_config = {
> > + .irq1 = {
> > + .addr = 0x0d,
> > + .mask = BIT(3),
> > + },
> > + .irq2 = {
> > + .addr = 0x0e,
> > + .mask = BIT(3),
> > + },
> > + .lir = {
> > + .addr = 0x56,
> > + .mask = BIT(0),
> > + },
> > + .clear_on_read = {
> > + .addr = 0x56,
> > + .mask = BIT(6),
> > + },
> > + .irq1_func = {
> > + .addr = 0x5e,
> > + .mask = BIT(5),
> > + },
> > + .irq2_func = {
> > + .addr = 0x5f,
> > + .mask = BIT(5),
> > + },
> > + },
> > .batch = {
> > [ST_LSM6DSX_ID_ACC] = {
> > .addr = 0x09,
> > @@ -792,14 +867,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .mask = GENMASK(7, 4),
> > },
> > },
> > - .lir = {
> > - .addr = 0x56,
> > - .mask = BIT(0),
> > - },
> > - .clear_on_read = {
> > - .addr = 0x56,
> > - .mask = BIT(6),
> > - },
> > .fifo_ops = {
> > .update_fifo = st_lsm6dsx_update_fifo,
> > .read_fifo = st_lsm6dsx_read_tagged_fifo,
> > @@ -841,11 +908,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > },
> > {
> > .wai = 0x6b,
> > - .int1_addr = 0x0d,
> > - .int2_addr = 0x0e,
> > - .int1_func_addr = 0x5e,
> > - .int2_func_addr = 0x5f,
> > - .int_func_mask = BIT(5),
> > .reset_addr = 0x12,
> > .max_fifo_size = 512,
> > .id = {
> > @@ -915,6 +977,32 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
> > },
> > },
> > + .irq_config = {
> > + .irq1 = {
> > + .addr = 0x0d,
> > + .mask = BIT(3),
> > + },
> > + .irq2 = {
> > + .addr = 0x0e,
> > + .mask = BIT(3),
> > + },
> > + .lir = {
> > + .addr = 0x56,
> > + .mask = BIT(0),
> > + },
> > + .clear_on_read = {
> > + .addr = 0x56,
> > + .mask = BIT(6),
> > + },
> > + .irq1_func = {
> > + .addr = 0x5e,
> > + .mask = BIT(5),
> > + },
> > + .irq2_func = {
> > + .addr = 0x5f,
> > + .mask = BIT(5),
> > + },
> > + },
> > .batch = {
> > [ST_LSM6DSX_ID_ACC] = {
> > .addr = 0x09,
> > @@ -925,14 +1013,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
> > .mask = GENMASK(7, 4),
> > },
> > },
> > - .lir = {
> > - .addr = 0x56,
> > - .mask = BIT(0),
> > - },
> > - .clear_on_read = {
> > - .addr = 0x56,
> > - .mask = BIT(6),
> > - },
> > .fifo_ops = {
> > .update_fifo = st_lsm6dsx_update_fifo,
> > .read_fifo = st_lsm6dsx_read_tagged_fifo,
> > @@ -1281,7 +1361,7 @@ static int st_lsm6dsx_event_setup(struct st_lsm6dsx_hw *hw, int state)
> > int err;
> > u8 enable = 0;
> >
> > - if (!hw->settings->int1_func_addr)
> > + if (!hw->settings->irq_config.irq1_func.addr)
> > return -ENOTSUPP;
> >
> > enable = state ? hw->settings->event_settings.enable_reg.mask : 0;
> > @@ -1293,12 +1373,11 @@ static int st_lsm6dsx_event_setup(struct st_lsm6dsx_hw *hw, int state)
> > if (err < 0)
> > return err;
> >
> > - enable = state ? hw->irq_routing.mask : 0;
> > + enable = state ? hw->irq_routing->mask : 0;
> >
> > /* Enable wakeup interrupt */
> > - return regmap_update_bits(hw->regmap, hw->irq_routing.addr,
> > - hw->irq_routing.mask,
> > - enable);
> > + return regmap_update_bits(hw->regmap, hw->irq_routing->addr,
> > + hw->irq_routing->mask, enable);
> > }
> >
> > static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
> > @@ -1527,7 +1606,9 @@ static int st_lsm6dsx_of_get_drdy_pin(struct st_lsm6dsx_hw *hw, int *drdy_pin)
> > return of_property_read_u32(np, "st,drdy-int-pin", drdy_pin);
> > }
> >
> > -static int st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, u8 *drdy_reg)
> > +static int
> > +st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw,
> > + const struct st_lsm6dsx_reg **drdy_reg)
> > {
> > int err = 0, drdy_pin;
> >
> > @@ -1541,14 +1622,12 @@ static int st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, u8 *drdy_reg)
> >
> > switch (drdy_pin) {
> > case 1:
> > - *drdy_reg = hw->settings->int1_addr;
> > - hw->irq_routing.addr = hw->settings->int1_func_addr;
> > - hw->irq_routing.mask = hw->settings->int_func_mask;
> > + hw->irq_routing = &hw->settings->irq_config.irq1_func;
> > + *drdy_reg = &hw->settings->irq_config.irq1;
> > break;
> > case 2:
> > - *drdy_reg = hw->settings->int2_addr;
> > - hw->irq_routing.addr = hw->settings->int2_func_addr;
> > - hw->irq_routing.mask = hw->settings->int_func_mask;
> > + hw->irq_routing = &hw->settings->irq_config.irq2_func;
> > + *drdy_reg = &hw->settings->irq_config.irq2;
> > break;
> > default:
> > dev_err(hw->dev, "unsupported data ready pin\n");
> > @@ -1644,7 +1723,7 @@ static int st_lsm6dsx_init_hw_timer(struct st_lsm6dsx_hw *hw)
> >
> > static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw)
> > {
> > - u8 drdy_int_reg;
> > + const struct st_lsm6dsx_reg *reg;
> > int err;
> >
> > /* device sw reset */
> > @@ -1673,35 +1752,29 @@ static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw)
> > return err;
> >
> > /* enable FIFO watermak interrupt */
> > - err = st_lsm6dsx_get_drdy_reg(hw, &drdy_int_reg);
> > + err = st_lsm6dsx_get_drdy_reg(hw, ®);
> > if (err < 0)
> > return err;
> >
> > - err = regmap_update_bits(hw->regmap, drdy_int_reg,
> > - ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK,
> > - FIELD_PREP(ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK,
> > - 1));
> > + err = regmap_update_bits(hw->regmap, reg->addr, reg->mask,
> > + ST_LSM6DSX_SHIFT_VAL(1, reg->mask));
> > if (err < 0)
> > return err;
> >
> > /* enable Latched interrupts for device events */
> > - if (hw->settings->lir.addr) {
> > - unsigned int data;
> > -
> > - data = ST_LSM6DSX_SHIFT_VAL(1, hw->settings->lir.mask);
> > - err = regmap_update_bits(hw->regmap, hw->settings->lir.addr,
> > - hw->settings->lir.mask, data);
> > + if (hw->settings->irq_config.lir.addr) {
> > + reg = &hw->settings->irq_config.lir;
> > + err = regmap_update_bits(hw->regmap, reg->addr, reg->mask,
> > + ST_LSM6DSX_SHIFT_VAL(1, reg->mask));
> > if (err < 0)
> > return err;
> >
> > /* enable clear on read for latched interrupts */
> > - if (hw->settings->clear_on_read.addr) {
> > - data = ST_LSM6DSX_SHIFT_VAL(1,
> > - hw->settings->clear_on_read.mask);
> > + if (hw->settings->irq_config.clear_on_read.addr) {
> > + reg = &hw->settings->irq_config.clear_on_read;
> > err = regmap_update_bits(hw->regmap,
> > - hw->settings->clear_on_read.addr,
> > - hw->settings->clear_on_read.mask,
> > - data);
> > + reg->addr, reg->mask,
> > + ST_LSM6DSX_SHIFT_VAL(1, reg->mask));
> > if (err < 0)
> > return err;
> > }
> >
next prev parent reply other threads:[~2019-10-12 12:13 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-06 13:21 [PATCH 00/13] various st_lsm6dsx fixes and missing bits Lorenzo Bianconi
2019-10-06 13:21 ` [PATCH 01/13] iio: imu: st_lsm6dsx: use st_lsm6dsx_read_locked in st_lsm6dsx_report_motion_event Lorenzo Bianconi
2019-10-07 7:54 ` Sean Nyekjaer
2019-10-12 12:08 ` Jonathan Cameron
2019-10-06 13:21 ` [PATCH 02/13] iio: imu: st_lsm6dsx: add sanity check for read_fifo pointer Lorenzo Bianconi
2019-10-06 13:21 ` [PATCH 03/13] iio: imu: st_lsm6dsx: move irq related definitions in irq_config Lorenzo Bianconi
2019-10-07 7:54 ` Sean Nyekjaer
2019-10-12 12:13 ` Jonathan Cameron [this message]
2019-10-06 13:21 ` [PATCH 04/13] iio: imu: st_lsm6dsx: do not access active-low/open-drain regs if not supported Lorenzo Bianconi
2019-10-12 12:14 ` Jonathan Cameron
2019-10-06 13:21 ` [PATCH 05/13] iio: imu: st_lsm6dsx: move bdu/boot and reset register info in hw_settings Lorenzo Bianconi
2019-10-12 12:19 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 06/13] iio: imu: st_lsm6dsx: always check enable_reg in st_lsm6dsx_event_setup Lorenzo Bianconi
2019-10-07 7:55 ` Sean Nyekjaer
2019-10-12 12:21 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 07/13] iio: imu: st_lsm6dsx: rely on st_lsm6dsx_update_bits_locked configuring events Lorenzo Bianconi
2019-10-12 12:22 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 08/13] iio: imu: st_lsm6dsx: grab conf mutex in st_lsm6dsx_write_event_config Lorenzo Bianconi
2019-10-12 12:23 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 09/13] iio: imu: st_lsm6dsx: fix checkpatch warning Lorenzo Bianconi
2019-10-12 12:24 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 10/13] iio: imu: st_lsm6dsx: add wakeup_source in st_sensors_platform_data Lorenzo Bianconi
2019-10-12 12:25 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 11/13] iio: imu: st_lsm6dsx: add missing kernel documenation Lorenzo Bianconi
2019-10-07 7:56 ` Sean Nyekjaer
2019-10-12 12:26 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 12/13] dt-bindings: iio: imu: st_lsm6dsx: document missing wakeup-source property Lorenzo Bianconi
2019-10-07 7:56 ` Sean Nyekjaer
2019-10-15 20:34 ` Rob Herring
2019-10-06 13:22 ` [PATCH 13/13] iio: imu: st_lsm6dsx: enable wake-up event for LSM6DSO Lorenzo Bianconi
2019-10-12 12:28 ` Jonathan Cameron
2019-10-12 12:20 ` [PATCH 00/13] various st_lsm6dsx fixes and missing bits Jonathan Cameron
2019-10-12 12:26 ` Lorenzo Bianconi
2019-10-12 13:26 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191012131304.321f7240@archlinux \
--to=jic23@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=lorenzo.bianconi@redhat.com \
--cc=lorenzo@kernel.org \
--cc=martin@geanix.com \
--cc=rjones@gateworks.com \
--cc=sean@geanix.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox