From: Claudiu Beznea <claudiu.beznea@microchip.com>
To: <eugen.hristev@microchip.com>, <jic23@kernel.org>,
<lars@metafoo.de>, <nicolas.ferre@microchip.com>,
<alexandre.belloni@bootlin.com>, <robh+dt@kernel.org>,
<krzk+dt@kernel.org>, <ludovic.desroches@atmel.com>
Cc: <linux-iio@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Claudiu Beznea <claudiu.beznea@microchip.com>
Subject: [PATCH 04/16] iio: adc: at91-sama5d2_adc: handle different EMR.OSR for different hw versions
Date: Thu, 9 Jun 2022 11:32:01 +0300 [thread overview]
Message-ID: <20220609083213.1795019-5-claudiu.beznea@microchip.com> (raw)
In-Reply-To: <20220609083213.1795019-1-claudiu.beznea@microchip.com>
SAMA7G5 introduces 64 and 256 oversampling rates. Due to this EMR.OSR is 3
bits long. Change the code to reflect this. Commit prepares the code
for the addition of 64 and 256 oversampling rates.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---
drivers/iio/adc/at91-sama5d2_adc.c | 55 ++++++++++++++++++++++--------
1 file changed, 40 insertions(+), 15 deletions(-)
diff --git a/drivers/iio/adc/at91-sama5d2_adc.c b/drivers/iio/adc/at91-sama5d2_adc.c
index b76328da0cb2..1ceab097335c 100644
--- a/drivers/iio/adc/at91-sama5d2_adc.c
+++ b/drivers/iio/adc/at91-sama5d2_adc.c
@@ -138,8 +138,7 @@ struct at91_adc_reg_layout {
/* Extended Mode Register */
u16 EMR;
/* Extended Mode Register - Oversampling rate */
-#define AT91_SAMA5D2_EMR_OSR(V) ((V) << 16)
-#define AT91_SAMA5D2_EMR_OSR_MASK GENMASK(17, 16)
+#define AT91_SAMA5D2_EMR_OSR(V, M) (((V) << 16) & (M))
#define AT91_SAMA5D2_EMR_OSR_1SAMPLES 0
#define AT91_SAMA5D2_EMR_OSR_4SAMPLES 1
#define AT91_SAMA5D2_EMR_OSR_16SAMPLES 2
@@ -403,6 +402,8 @@ static const struct at91_adc_reg_layout sama7g5_layout = {
* @max_index: highest channel index (highest index may be higher
* than the total channel number)
* @hw_trig_cnt: number of possible hardware triggers
+ * @osr_mask: oversampling ratio bitmask on EMR register
+ * @osr_vals: available oversampling rates
*/
struct at91_adc_platform {
const struct at91_adc_reg_layout *layout;
@@ -414,6 +415,8 @@ struct at91_adc_platform {
unsigned int max_channels;
unsigned int max_index;
unsigned int hw_trig_cnt;
+ unsigned int osr_mask;
+ unsigned int osr_vals;
};
/**
@@ -612,6 +615,10 @@ static const struct at91_adc_platform sama5d2_platform = {
.max_index = AT91_SAMA5D2_MAX_CHAN_IDX,
#define AT91_SAMA5D2_HW_TRIG_CNT 3
.hw_trig_cnt = AT91_SAMA5D2_HW_TRIG_CNT,
+ .osr_mask = GENMASK(17, 16),
+ .osr_vals = BIT(AT91_SAMA5D2_EMR_OSR_1SAMPLES) |
+ BIT(AT91_SAMA5D2_EMR_OSR_4SAMPLES) |
+ BIT(AT91_SAMA5D2_EMR_OSR_16SAMPLES),
};
static const struct at91_adc_platform sama7g5_platform = {
@@ -627,6 +634,10 @@ static const struct at91_adc_platform sama7g5_platform = {
.max_index = AT91_SAMA7G5_MAX_CHAN_IDX,
#define AT91_SAMA7G5_HW_TRIG_CNT 3
.hw_trig_cnt = AT91_SAMA7G5_HW_TRIG_CNT,
+ .osr_mask = GENMASK(18, 16),
+ .osr_vals = BIT(AT91_SAMA5D2_EMR_OSR_1SAMPLES) |
+ BIT(AT91_SAMA5D2_EMR_OSR_4SAMPLES) |
+ BIT(AT91_SAMA5D2_EMR_OSR_16SAMPLES),
};
static int at91_adc_chan_xlate(struct iio_dev *indio_dev, int chan)
@@ -725,34 +736,45 @@ static void at91_adc_eoc_ena(struct at91_adc_state *st, unsigned int channel)
at91_adc_writel(st, EOC_IER, BIT(channel));
}
-static void at91_adc_config_emr(struct at91_adc_state *st)
+static int at91_adc_config_emr(struct at91_adc_state *st,
+ u32 oversampling_ratio)
{
/* configure the extended mode register */
unsigned int emr = at91_adc_readl(st, EMR);
+ unsigned int osr_mask = st->soc_info.platform->osr_mask;
+ unsigned int osr_vals = st->soc_info.platform->osr_vals;
/* select oversampling per single trigger event */
emr |= AT91_SAMA5D2_EMR_ASTE(1);
/* delete leftover content if it's the case */
- emr &= ~AT91_SAMA5D2_EMR_OSR_MASK;
+ emr &= ~osr_mask;
/* select oversampling ratio from configuration */
- switch (st->oversampling_ratio) {
+ switch (oversampling_ratio) {
case AT91_OSR_1SAMPLES:
- emr |= AT91_SAMA5D2_EMR_OSR(AT91_SAMA5D2_EMR_OSR_1SAMPLES) &
- AT91_SAMA5D2_EMR_OSR_MASK;
+ if (!(osr_vals & BIT(AT91_SAMA5D2_EMR_OSR_1SAMPLES)))
+ return -EINVAL;
+ emr |= AT91_SAMA5D2_EMR_OSR(AT91_SAMA5D2_EMR_OSR_1SAMPLES,
+ osr_mask);
break;
case AT91_OSR_4SAMPLES:
- emr |= AT91_SAMA5D2_EMR_OSR(AT91_SAMA5D2_EMR_OSR_4SAMPLES) &
- AT91_SAMA5D2_EMR_OSR_MASK;
+ if (!(osr_vals & BIT(AT91_SAMA5D2_EMR_OSR_4SAMPLES)))
+ return -EINVAL;
+ emr |= AT91_SAMA5D2_EMR_OSR(AT91_SAMA5D2_EMR_OSR_4SAMPLES,
+ osr_mask);
break;
case AT91_OSR_16SAMPLES:
- emr |= AT91_SAMA5D2_EMR_OSR(AT91_SAMA5D2_EMR_OSR_16SAMPLES) &
- AT91_SAMA5D2_EMR_OSR_MASK;
+ if (!(osr_vals & BIT(AT91_SAMA5D2_EMR_OSR_16SAMPLES)))
+ return -EINVAL;
+ emr |= AT91_SAMA5D2_EMR_OSR(AT91_SAMA5D2_EMR_OSR_16SAMPLES,
+ osr_mask);
break;
}
at91_adc_writel(st, EMR, emr);
+
+ return 0;
}
static int at91_adc_adjust_val_osr(struct at91_adc_state *st, int *val)
@@ -1643,6 +1665,7 @@ static int at91_adc_write_raw(struct iio_dev *indio_dev,
int val, int val2, long mask)
{
struct at91_adc_state *st = iio_priv(indio_dev);
+ int ret = 0;
if (iio_buffer_enabled(indio_dev))
return -EBUSY;
@@ -1656,12 +1679,14 @@ static int at91_adc_write_raw(struct iio_dev *indio_dev,
mutex_lock(&st->lock);
if (val == st->oversampling_ratio)
goto unlock;
- st->oversampling_ratio = val;
/* update ratio */
- at91_adc_config_emr(st);
+ ret = at91_adc_config_emr(st, val);
+ if (ret)
+ goto unlock;
+ st->oversampling_ratio = val;
unlock:
mutex_unlock(&st->lock);
- return 0;
+ return ret;
case IIO_CHAN_INFO_SAMP_FREQ:
if (val < st->soc_info.min_sample_rate ||
val > st->soc_info.max_sample_rate)
@@ -1834,7 +1859,7 @@ static void at91_adc_hw_init(struct iio_dev *indio_dev)
at91_adc_setup_samp_freq(indio_dev, st->soc_info.min_sample_rate);
/* configure extended mode register */
- at91_adc_config_emr(st);
+ at91_adc_config_emr(st, st->oversampling_ratio);
}
static ssize_t at91_adc_get_fifo_state(struct device *dev,
--
2.34.1
next prev parent reply other threads:[~2022-06-09 8:30 UTC|newest]
Thread overview: 41+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-06-09 8:31 [PATCH 00/16] iio: adc: at91-sama5d2_adc: add support for temperature sensor Claudiu Beznea
2022-06-09 8:31 ` [PATCH 01/16] iio: adc: at91-sama5d2_adc: fix AT91_SAMA5D2_MR_TRACKTIM_MAX Claudiu Beznea
2022-06-09 8:31 ` [PATCH 02/16] iio: adc: at91-sama5d2_adc: lock around oversampling and sample freq Claudiu Beznea
2022-06-11 17:30 ` Jonathan Cameron
2022-06-14 8:19 ` Claudiu.Beznea
2022-06-09 8:32 ` [PATCH 03/16] iio: adc: at91-sama5d2_adc: exit from write_raw() when buffers are enabled Claudiu Beznea
2022-06-11 17:33 ` Jonathan Cameron
2022-06-14 8:19 ` Claudiu.Beznea
2022-06-09 8:32 ` Claudiu Beznea [this message]
2022-06-11 17:46 ` [PATCH 04/16] iio: adc: at91-sama5d2_adc: handle different EMR.OSR for different hw versions Jonathan Cameron
2022-06-14 8:20 ` Claudiu.Beznea
2022-06-09 8:32 ` [PATCH 05/16] iio: adc: at91-sama5d2_adc: adjust osr based on specific platform data Claudiu Beznea
2022-06-09 8:32 ` [PATCH 06/16] iio: adc: at91-sama5d2_adc: add 64 and 256 oversampling ratio Claudiu Beznea
2022-06-11 17:47 ` Jonathan Cameron
2022-06-14 8:22 ` Claudiu.Beznea
2022-06-09 8:32 ` [PATCH 07/16] iio: adc: at91-sama5d2_adc: simplify the code in at91_adc_read_info_raw() Claudiu Beznea
2022-06-11 17:54 ` Jonathan Cameron
2022-06-14 8:49 ` Claudiu.Beznea
2022-06-14 12:00 ` Jonathan Cameron
2022-06-09 8:32 ` [PATCH 08/16] iio: adc: at91-sama5d2_adc: move oversampling storage in its function Claudiu Beznea
2022-06-09 8:32 ` [PATCH 09/16] iio: adc: at91-sama5d2_adc: update trackx on emr Claudiu Beznea
2022-06-09 8:32 ` [PATCH 10/16] iio: adc: at91-sama5d2_adc: add startup and tracktim as parameter for at91_adc_setup_samp_freq() Claudiu Beznea
2022-06-09 8:32 ` [PATCH 11/16] iio: adc: at91-sama5d2_adc: add locking parameter to at91_adc_read_info_raw() Claudiu Beznea
2022-06-11 17:58 ` Jonathan Cameron
2022-06-14 8:50 ` Claudiu.Beznea
2022-06-14 12:02 ` Jonathan Cameron
2022-06-09 8:32 ` [PATCH 12/16] dt-bindings: iio: adc: at91-sama5d2_adc: add id for temperature channel Claudiu Beznea
2022-06-16 16:00 ` Rob Herring
2022-06-09 8:32 ` [PATCH 13/16] iio: adc: at91-sama5d2_adc: add support for temperature sensor Claudiu Beznea
2022-06-11 18:15 ` Jonathan Cameron
2022-06-14 10:13 ` Claudiu.Beznea
2022-06-14 12:10 ` Jonathan Cameron
2022-06-09 8:32 ` [PATCH 14/16] iio: adc: at91-sama5d2_adc: add empty line after functions Claudiu Beznea
2022-06-09 8:32 ` [PATCH 15/16] iio: adc: at91-sama5d2_adc: add runtime pm support Claudiu Beznea
2022-06-11 16:48 ` Jonathan Cameron
2022-06-14 10:40 ` Claudiu.Beznea
2022-06-14 12:14 ` Jonathan Cameron
2022-06-09 8:32 ` [PATCH 16/16] iio: adc: at91-sama5d2_adc: use pm_ptr() Claudiu Beznea
2022-06-11 16:40 ` Jonathan Cameron
2022-06-11 18:16 ` [PATCH 00/16] iio: adc: at91-sama5d2_adc: add support for temperature sensor Jonathan Cameron
2022-06-14 10:41 ` Claudiu.Beznea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220609083213.1795019-5-claudiu.beznea@microchip.com \
--to=claudiu.beznea@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=eugen.hristev@microchip.com \
--cc=jic23@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=lars@metafoo.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=ludovic.desroches@atmel.com \
--cc=nicolas.ferre@microchip.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox