Re: [PATCH v3 0/2] AD74115

[Jonathan Cameron <jic23@kernel.org>]

On Thu, 17 Nov 2022 10:09:14 +0200
Cosmin Tanislav <demonsingur@gmail.com> wrote:

> The AD74115H is a single-channel, software-configurable, input and
> output device for industrial control applications. The AD74115H
> provides a wide range of use cases, integrated on a single chip.
> 
> These use cases include analog output, analog input, digital output,
> digital input, resistance temperature detector (RTD), and thermocouple
> measurement capability. The AD74115H also has an integrated HART modem.
> 
> A serial peripheral interface (SPI) is used to handle all communications
> to the device, including communications with the HART modem. The digital
> input and digital outputs can be accessed via the SPI or the
> general-purpose input and output (GPIO) pins to support higher
> speed data rates.
> 
> The device features a 16-bit, sigma-delta analog-to-digital converter
> (ADC) and a 14-bit digital-to-analog converter (DAC).
> The AD74115H contains a high accuracy 2.5 V on-chip reference that can
> be used as the DAC and ADC reference.
> 
Applied to the togreg branch of iio.git.

Thanks,

Jonathan

> V2 -> V3:
>  * dt-bindings: remove address and size cells specifiers
>  * dt-bindings: additionalProperties -> unevaluatedProperties
>  * dt-bindings: remove pipe where not needed
>  * dt-bindings: use required for adi,digital-input-sink-range-high: true
>  * do not uselessly store poll time
>  * fix ad74115_adc_gain capitalization
>  * inline ad74115_channels_map[st->ch_func] access
>  * keep consistent table naming
>  * remove aldo1v8 regulator
>  * spell out low-power
>  * split up resistance offset and scale into separate function
>  * use adc_rdy name for irq
>  * use microvolt for conv2 range
>  * use unsigned int for ad74115_adc_conv_mul
>  * use unsigned int for ad74115_adc_gain
>  * wrap module_driver call less
> 
> V1 -> V2:
>  * dt-bindings: add spi peripheral allOf
>  * dt-bindings: remove cs-gpios
>  * dt-bindings: remove refin supply from example
>  * dt-bindings: remove status
>  * sort includes
>  * ad74115_parse_fw_prop -> ad74115_apply_fw_prop
>  * ad74115_setup_{comp,}_gc -> ad74115_setup_{comp,}_gpio_chip
>  * gpiod_get_optional -> devm_gpiod_get_optional
>  * add support for reset-gpios
>  * add support for running without an interrupt
>  * fix comma after terminating member
>  * fix order of rate and range masks
>  * fix reset pin wait time and out of reset time
>  * fix rtd mode reading
>  * pass chan spec only where needed
>  * remove -en suffix
>  * remove default 0 values
>  * remove diag support
>  * remove unecessary prop storage
>  * reorder switch cases to match enum
>  * set burnout enable bit based on burnout current
>  * set default value for props
>  * simplify dac hart slew usage
>  * simplify prop value validation
>  * use bool for 4 wire rtd mode
>  * use bool for burnout current polarity
>  * use bool for dac sc current limit
>  * use bool for debounce mode
>  * use bool for din sink range
>  * use bool for din threshold mode
>  * use devm_regulator_bulk_get_enable
>  * use IIO_VAL_FRACTIONAL for resistance offset
>  * use struct assignment for gpiochip
>  * warn on empty prop mask
> 
> Cosmin Tanislav (2):
>   dt-bindings: iio: addac: add AD74115
>   iio: addac: add AD74115 driver
> 
>  .../bindings/iio/addac/adi,ad74115.yaml       |  373 ++++
>  MAINTAINERS                                   |    8 +
>  drivers/iio/addac/Kconfig                     |   14 +
>  drivers/iio/addac/Makefile                    |    1 +
>  drivers/iio/addac/ad74115.c                   | 1947 +++++++++++++++++
>  5 files changed, 2343 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/addac/adi,ad74115.yaml
>  create mode 100644 drivers/iio/addac/ad74115.c
>