Re: [PATCH] iio: ABI: combine current input sections

[Jonathan Cameron <jic23@kernel.org>]

On Thu, 19 Dec 2024 13:25:23 -0600
David Lechner <dlechner@baylibre.com> wrote:

> Combine two duplicate sections describing in_currentY_raw.
> 
> This went unnoticed until we renamed in_currentX_raw to in_currentY_raw
> and the kernel test robot found the duplication.
> 
> Reported-by: kernel test robot <lkp@intel.com>
> Closes: https://lore.kernel.org/oe-kbuild-all/202412200256.OB5Hmw5Q-lkp@intel.com/
> Signed-off-by: David Lechner <dlechner@baylibre.com>
Applied.
Thanks,

J
> ---
>  Documentation/ABI/testing/sysfs-bus-iio | 19 +++++--------------
>  1 file changed, 5 insertions(+), 14 deletions(-)
> 
> diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
> index d97c35057a034c76ed433e3e6de0aff8ec4bbb70..25d366d452a55293c420300335a0271a28855107 100644
> --- a/Documentation/ABI/testing/sysfs-bus-iio
> +++ b/Documentation/ABI/testing/sysfs-bus-iio
> @@ -168,18 +168,6 @@ Description:
>  		is required is a consistent labeling.  Units after application
>  		of scale and offset are millivolts.
>  
> -What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_raw
> -What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_supply_raw
> -KernelVersion:	3.17
> -Contact:	linux-iio@vger.kernel.org
> -Description:
> -		Raw (unscaled no bias removal etc.) current measurement from
> -		channel Y. In special cases where the channel does not
> -		correspond to externally available input one of the named
> -		versions may be used. The number must always be specified and
> -		unique to allow association with event codes. Units after
> -		application of scale and offset are milliamps.
> -
>  What:		/sys/bus/iio/devices/iio:deviceX/in_powerY_raw
>  KernelVersion:	4.5
>  Contact:	linux-iio@vger.kernel.org
> @@ -1700,15 +1688,18 @@ Description:
>  		or without compensation from tilt sensors.
>  
>  What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_raw
> +What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_supply_raw
>  What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_i_raw
>  What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_q_raw
> -KernelVersion:	3.18
> +KernelVersion:	3.17
>  Contact:	linux-iio@vger.kernel.org
>  Description:
>  		Raw current measurement from channel Y. Units are in milliamps
>  		after application of scale and offset. If no offset or scale is
>  		present, output should be considered as processed with the
> -		unit in milliamps.
> +		unit in milliamps. In special cases where the channel does not
> +		correspond to externally available input one of the named
> +		versions may be used.
>  
>  		Channels with 'i' and 'q' modifiers always exist in pairs and both
>  		channels refer to the same signal. The 'i' channel contains the in-phase
> 
> ---
> base-commit: fe2a04fbcbfe44694fcb36ff6212fce54b8f56cc
> change-id: 20241219-iio-abi-combine-current-input-sections-c62cf5dbfa9b
> 
> Best regards,