linux-iio.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Jonathan Cameron <jic23@kernel.org>
To: Juergen Beisert <jbe@pengutronix.de>, linux-iio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org, devel@driverdev.osuosl.org,
	marex@denx.de, fabio.estevam@freescale.com, jic23@cam.ac.uk,
	linux-input@vger.kernel.org, devicetree@vger.kernel.org
Subject: Re: [PATCH 8/9] Staging/iio/adc/touchscreen/MXS: provide devicetree adaption
Date: Tue, 01 Oct 2013 12:14:04 +0100	[thread overview]
Message-ID: <524AAE7C.50702@kernel.org> (raw)
In-Reply-To: <1379946998-23041-9-git-send-email-jbe@pengutronix.de>

On 09/23/13 15:36, Juergen Beisert wrote:
> This is an RFC for the new touchscreen properties.
> 
> Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
> CC: linux-arm-kernel@lists.infradead.org
> CC: linux-input@vger.kernel.org
> CC: devel@driverdev.osuosl.org
> CC: Marek Vasut <marex@denx.de>
> CC: Fabio Estevam <fabio.estevam@freescale.com>
> CC: Jonathan Cameron <jic23@cam.ac.uk>
> CC: devicetree@vger.kernel.org
Applied to the togreg branch of iio.git

Thanks,
> ---
>  .../bindings/staging/iio/adc/mxs-lradc.txt         | 36 ++++++++++++--
>  arch/arm/boot/dts/imx28-evk.dts                    |  4 ++
>  drivers/staging/iio/adc/mxs-lradc.c                | 57 ++++++++++++++--------
>  3 files changed, 71 insertions(+), 26 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt
> index 4688205..ee05dc3 100644
> --- a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt
> +++ b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt
> @@ -1,7 +1,8 @@
>  * Freescale i.MX28 LRADC device driver
>  
>  Required properties:
> -- compatible: Should be "fsl,imx28-lradc"
> +- compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc"
> +              for i.MX28 SoC
>  - reg: Address and length of the register set for the device
>  - interrupts: Should contain the LRADC interrupts
>  
> @@ -9,13 +10,38 @@ Optional properties:
>  - fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen
>                                 to LRADC. Valid value is either 4 or 5. If this
>                                 property is not present, then the touchscreen is
> -                               disabled.
> +                               disabled. 5 wires is valid for i.MX28 SoC only.
> +- fsl,ave-ctrl: number of samples per direction to calculate an average value.
> +                Allowed value is 1 ... 31, default is 4
> +- fsl,ave-delay: delay between consecutive samples. Allowed value is
> +                 1 ... 2047. It is used if 'fsl,ave-ctrl' > 1, counts at
> +                 2 kHz and its default is 2 (= 1 ms)
> +- fsl,settling: delay between plate switch to next sample. Allowed value is
> +                1 ... 2047. It counts at 2 kHz and its default is
> +                10 (= 5 ms)
>  
> -Examples:
> +Example for i.MX23 SoC:
> +
> +	lradc@80050000 {
> +		compatible = "fsl,imx23-lradc";
> +		reg = <0x80050000 0x2000>;
> +		interrupts = <36 37 38 39 40 41 42 43 44>;
> +		status = "okay";
> +		fsl,lradc-touchscreen-wires = <4>;
> +		fsl,ave-ctrl = <4>;
> +		fsl,ave-delay = <2>;
> +		fsl,settling = <10>;
> +	};
> +
> +Example for i.MX28 SoC:
>  
>  	lradc@80050000 {
>  		compatible = "fsl,imx28-lradc";
>  		reg = <0x80050000 0x2000>;
> -		interrupts = <10 14 15 16 17 18 19
> -				20 21 22 23 24 25>;
> +		interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>;
> +		status = "okay";
> +		fsl,lradc-touchscreen-wires = <5>;
> +		fsl,ave-ctrl = <4>;
> +		fsl,ave-delay = <2>;
> +		fsl,settling = <10>;
>  	};
> diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
> index 15715d9..aa33393 100644
> --- a/arch/arm/boot/dts/imx28-evk.dts
> +++ b/arch/arm/boot/dts/imx28-evk.dts
> @@ -183,6 +183,10 @@
>  
>  			lradc@80050000 {
>  				status = "okay";
> +				fsl,lradc-touchscreen-wires = <4>;
> +				fsl,ave-ctrl = <4>;
> +				fsl,ave-delay = <2>;
> +				fsl,settling = <10>;
>  			};
>  
>  			i2c0: i2c@80058000 {
> diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c
> index aa1f337..dbc0af6 100644
> --- a/drivers/staging/iio/adc/mxs-lradc.c
> +++ b/drivers/staging/iio/adc/mxs-lradc.c
> @@ -1230,10 +1230,45 @@ MODULE_DEVICE_TABLE(of, mxs_lradc_dt_ids);
>  static int mxs_lradc_probe_touchscreen(struct mxs_lradc *lradc,
>  						struct device_node *lradc_node)
>  {
> -	/* TODO retrieve from device tree */
> +	int ret;
> +	u32 ts_wires = 0, adapt;
> +
> +	ret = of_property_read_u32(lradc_node, "fsl,lradc-touchscreen-wires",
> +				&ts_wires);
> +	if (ret)
> +		return -ENODEV; /* touchscreen feature disabled */
> +
> +	switch (ts_wires) {
> +	case 4:
> +		lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_4WIRE;
> +		break;
> +	case 5:
> +		if (lradc->soc == IMX28_LRADC) {
> +			lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_5WIRE;
> +			break;
> +		}
> +		/* fall through an error message for i.MX23 */
> +	default:
> +		dev_err(lradc->dev,
> +			"Unsupported number of touchscreen wires (%d)\n",
> +			ts_wires);
> +		return -EINVAL;
> +	}
> +
>  	lradc->over_sample_cnt = 4;
> +	ret = of_property_read_u32(lradc_node, "fsl,ave-ctrl", &adapt);
> +	if (ret == 0)
> +		lradc->over_sample_cnt = adapt;
> +
>  	lradc->over_sample_delay = 2;
> +	ret = of_property_read_u32(lradc_node, "fsl,ave-delay", &adapt);
> +	if (ret == 0)
> +		lradc->over_sample_delay = adapt;
> +
>  	lradc->settling_delay = 10;
> +	ret = of_property_read_u32(lradc_node, "fsl,settling", &adapt);
> +	if (ret == 0)
> +		lradc->settling_delay = adapt;
>  
>  	return 0;
>  }
> @@ -1249,7 +1284,6 @@ static int mxs_lradc_probe(struct platform_device *pdev)
>  	struct mxs_lradc *lradc;
>  	struct iio_dev *iio;
>  	struct resource *iores;
> -	uint32_t ts_wires = 0;
>  	int ret = 0, touch_ret;
>  	int i;
>  
> @@ -1275,25 +1309,6 @@ static int mxs_lradc_probe(struct platform_device *pdev)
>  
>  	touch_ret = mxs_lradc_probe_touchscreen(lradc, node);
>  
> -	/* Check if touchscreen is enabled in DT. */
> -	ret = of_property_read_u32(node, "fsl,lradc-touchscreen-wires",
> -				&ts_wires);
> -	if (ret)
> -		dev_info(dev, "Touchscreen not enabled.\n");
> -	else if (ts_wires == 4)
> -		lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_4WIRE;
> -	else if (ts_wires == 5)
> -		lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_5WIRE;
> -	else
> -		dev_warn(dev, "Unsupported number of touchscreen wires (%d)\n",
> -				ts_wires);
> -
> -	if ((lradc->soc == IMX23_LRADC) && (ts_wires == 5)) {
> -		dev_warn(dev, "No support for 5 wire touches on i.MX23\n");
> -		dev_warn(dev, "Falling back to 4 wire\n");
> -		ts_wires = 4;
> -	}
> -
>  	/* Grab all IRQ sources */
>  	for (i = 0; i < of_cfg->irq_count; i++) {
>  		lradc->irq[i] = platform_get_irq(pdev, i);
> 

  reply	other threads:[~2013-10-01 10:13 UTC|newest]

Thread overview: 43+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-09-23 14:36 [PATCHv6] staging/iio/adc: change the MXS touchscreen driver implementation Juergen Beisert
2013-09-23 14:36 ` [PATCH 1/9] Staging/iio/adc/touchscreen/MXS: add proper clock handling Juergen Beisert
2013-09-23 15:13   ` Fabio Estevam
2013-09-24  7:50     ` Jürgen Beisert
2013-09-24 13:50       ` Fabio Estevam
2013-10-01 10:57       ` Jonathan Cameron
2013-09-23 15:30   ` Lothar Waßmann
2013-09-24  7:39     ` Jürgen Beisert
2013-09-23 14:36 ` [PATCH 2/9] Staging/iio/adc/touchscreen/MXS: distinguish i.MX23's and i.MX28's LRADC Juergen Beisert
2013-10-01 10:58   ` Jonathan Cameron
2013-09-23 14:36 ` [PATCH 3/9] Staging/iio/adc/touchscreen/MXS: separate i.MX28 specific register bits Juergen Beisert
2013-10-01 11:00   ` Jonathan Cameron
2013-09-23 14:36 ` [PATCH 4/9] Staging/iio/adc/touchscreen/MXS: simplify register access Juergen Beisert
2013-10-01 11:01   ` Jonathan Cameron
2013-09-23 14:36 ` [PATCH 5/9] Staging/iio/adc/touchscreen/MXS: add i.MX23 support to the LRADC touchscreen driver Juergen Beisert
2013-10-01 11:02   ` Jonathan Cameron
2013-09-23 14:36 ` [PATCH 6/9] Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection Juergen Beisert
2013-10-01  9:28   ` Jürgen Beisert
2013-10-01 10:51     ` Jonathan Cameron
2013-10-01 11:06       ` Jonathan Cameron
2013-09-23 14:36 ` [PATCH 7/9] Staging/iio/adc/touchscreen/MXS: remove old touchscreen detection implementation Juergen Beisert
2013-10-01 11:13   ` Jonathan Cameron
2013-09-23 14:36 ` [PATCH 8/9] Staging/iio/adc/touchscreen/MXS: provide devicetree adaption Juergen Beisert
2013-10-01 11:14   ` Jonathan Cameron [this message]
2013-09-23 14:36 ` [PATCH 9/9] Staging/iio: add TODO reminder Juergen Beisert
2013-10-01 11:14   ` Jonathan Cameron
2013-10-01 11:21     ` Jonathan Cameron
2013-09-23 15:25 ` [PATCHv6] staging/iio/adc: change the MXS touchscreen driver implementation Marek Vasut
2013-10-01  9:25 ` Jonathan Cameron
2013-10-01 10:49   ` Marek Vasut
2014-01-09 13:31 ` Alexandre Belloni
2014-01-10  8:55   ` Jürgen Beisert
2014-02-04 23:45     ` Marek Vasut
2014-02-24 13:16     ` Juergen Beisert
2014-02-24 13:33       ` Dan Carpenter
2014-02-24 14:38         ` Juergen Beisert
2014-02-24 14:47           ` Dan Carpenter
2014-02-24 14:39         ` [PATCH] staging/iio/adc/MXS/LRADC: fix touchscreen statemachine Juergen Beisert
2014-02-24 16:48           ` Alexandre Belloni
2014-02-24 21:14             ` Jonathan Cameron
2014-02-24 22:04               ` Jonathan Cameron
2014-02-24 14:26       ` [PATCHv6] staging/iio/adc: change the MXS touchscreen driver implementation Alexandre Belloni
2014-02-24 17:14         ` Jonathan Cameron

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=524AAE7C.50702@kernel.org \
    --to=jic23@kernel.org \
    --cc=devel@driverdev.osuosl.org \
    --cc=devicetree@vger.kernel.org \
    --cc=fabio.estevam@freescale.com \
    --cc=jbe@pengutronix.de \
    --cc=jic23@cam.ac.uk \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-iio@vger.kernel.org \
    --cc=linux-input@vger.kernel.org \
    --cc=marex@denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).