* [PATCH v4 1/5] iio: hid-sensors: accelerometer: Add sensitivity [not found] <a> @ 2013-11-06 0:11 ` Srinivas Pandruvada 2013-11-06 0:11 ` [PATCH v4 2/5] iio: hid-sensors: gyro : " Srinivas Pandruvada ` (3 more replies) 0 siblings, 4 replies; 8+ messages in thread From: Srinivas Pandruvada @ 2013-11-06 0:11 UTC (permalink / raw) To: jic23; +Cc: linux-iio, Srinivas Pandruvada A number of Properties that can be applied to Data Fields are per data field basis or for all data fields. Adding sensitivity field for all accelerometer fields, which is most commonly used in currently available sensor hubs. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> --- drivers/iio/accel/hid-sensor-accel-3d.c | 12 ++++++++++++ include/linux/hid-sensor-ids.h | 5 +++++ 2 files changed, 17 insertions(+) diff --git a/drivers/iio/accel/hid-sensor-accel-3d.c b/drivers/iio/accel/hid-sensor-accel-3d.c index 1cae4e9..3dcdbad 100644 --- a/drivers/iio/accel/hid-sensor-accel-3d.c +++ b/drivers/iio/accel/hid-sensor-accel-3d.c @@ -262,6 +262,18 @@ static int accel_3d_parse_report(struct platform_device *pdev, st->accel[1].index, st->accel[1].report_id, st->accel[2].index, st->accel[2].report_id); + /* Set Sensitivity field ids, when there is no individual modifier */ + if (st->common_attributes.sensitivity.index < 0) { + sensor_hub_input_get_attribute_info(hsdev, + HID_FEATURE_REPORT, usage_id, + HID_USAGE_SENSOR_DATA_MOD_CHANGE_SENSITIVITY_ABS | + HID_USAGE_SENSOR_DATA_ACCELERATION, + &st->common_attributes.sensitivity); + dev_dbg(&pdev->dev, "Sensitivity index:report %d:%d\n", + st->common_attributes.sensitivity.index, + st->common_attributes.sensitivity.report_id); + } + return ret; } diff --git a/include/linux/hid-sensor-ids.h b/include/linux/hid-sensor-ids.h index 4f945d3..38a832c 100644 --- a/include/linux/hid-sensor-ids.h +++ b/include/linux/hid-sensor-ids.h @@ -23,6 +23,7 @@ /* Accel 3D (200073) */ #define HID_USAGE_SENSOR_ACCEL_3D 0x200073 +#define HID_USAGE_SENSOR_DATA_ACCELERATION 0x200452 #define HID_USAGE_SENSOR_ACCEL_X_AXIS 0x200453 #define HID_USAGE_SENSOR_ACCEL_Y_AXIS 0x200454 #define HID_USAGE_SENSOR_ACCEL_Z_AXIS 0x200455 @@ -117,4 +118,8 @@ #define HID_USAGE_SENSOR_PROP_REPORT_STATE 0x200316 #define HID_USAGE_SENSOR_PROY_POWER_STATE 0x200319 +/* Per data field properties */ +#define HID_USAGE_SENSOR_DATA_MOD_NONE 0x00 +#define HID_USAGE_SENSOR_DATA_MOD_CHANGE_SENSITIVITY_ABS 0x1000 + #endif -- 1.8.3.1 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v4 2/5] iio: hid-sensors: gyro : Add sensitivity 2013-11-06 0:11 ` [PATCH v4 1/5] iio: hid-sensors: accelerometer: Add sensitivity Srinivas Pandruvada @ 2013-11-06 0:11 ` Srinivas Pandruvada 2013-11-06 0:11 ` [PATCH v4 3/5] iio: hid-sensors: light/als " Srinivas Pandruvada ` (2 subsequent siblings) 3 siblings, 0 replies; 8+ messages in thread From: Srinivas Pandruvada @ 2013-11-06 0:11 UTC (permalink / raw) To: jic23; +Cc: linux-iio, Srinivas Pandruvada A number of Properties that can be applied to Data Fields are per data field basis or for all data fields. Adding sensitivity field for all gyro fields, which is most commonly used in currently available sensor hubs. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> --- drivers/iio/gyro/hid-sensor-gyro-3d.c | 11 +++++++++++ include/linux/hid-sensor-ids.h | 1 + 2 files changed, 12 insertions(+) diff --git a/drivers/iio/gyro/hid-sensor-gyro-3d.c b/drivers/iio/gyro/hid-sensor-gyro-3d.c index e54f0f4..59d6bc3 100644 --- a/drivers/iio/gyro/hid-sensor-gyro-3d.c +++ b/drivers/iio/gyro/hid-sensor-gyro-3d.c @@ -262,6 +262,17 @@ static int gyro_3d_parse_report(struct platform_device *pdev, st->gyro[1].index, st->gyro[1].report_id, st->gyro[2].index, st->gyro[2].report_id); + /* Set Sensitivity field ids, when there is no individual modifier */ + if (st->common_attributes.sensitivity.index < 0) { + sensor_hub_input_get_attribute_info(hsdev, + HID_FEATURE_REPORT, usage_id, + HID_USAGE_SENSOR_DATA_MOD_CHANGE_SENSITIVITY_ABS | + HID_USAGE_SENSOR_DATA_ANGL_VELOCITY, + &st->common_attributes.sensitivity); + dev_dbg(&pdev->dev, "Sensitivity index:report %d:%d\n", + st->common_attributes.sensitivity.index, + st->common_attributes.sensitivity.report_id); + } return ret; } diff --git a/include/linux/hid-sensor-ids.h b/include/linux/hid-sensor-ids.h index 38a832c..b00ed85 100644 --- a/include/linux/hid-sensor-ids.h +++ b/include/linux/hid-sensor-ids.h @@ -34,6 +34,7 @@ /* Gyro 3D: (200076) */ #define HID_USAGE_SENSOR_GYRO_3D 0x200076 +#define HID_USAGE_SENSOR_DATA_ANGL_VELOCITY 0x200456 #define HID_USAGE_SENSOR_ANGL_VELOCITY_X_AXIS 0x200457 #define HID_USAGE_SENSOR_ANGL_VELOCITY_Y_AXIS 0x200458 #define HID_USAGE_SENSOR_ANGL_VELOCITY_Z_AXIS 0x200459 -- 1.8.3.1 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v4 3/5] iio: hid-sensors: light/als : Add sensitivity 2013-11-06 0:11 ` [PATCH v4 1/5] iio: hid-sensors: accelerometer: Add sensitivity Srinivas Pandruvada 2013-11-06 0:11 ` [PATCH v4 2/5] iio: hid-sensors: gyro : " Srinivas Pandruvada @ 2013-11-06 0:11 ` Srinivas Pandruvada 2013-11-06 0:11 ` [PATCH v4 4/5] iio: hid-sensors: magnetometer " Srinivas Pandruvada 2013-11-06 0:11 ` [PATCH v4 5/5] iio: hid-sensors: Added Inclinometer 3D Srinivas Pandruvada 3 siblings, 0 replies; 8+ messages in thread From: Srinivas Pandruvada @ 2013-11-06 0:11 UTC (permalink / raw) To: jic23; +Cc: linux-iio, Srinivas Pandruvada A number of Properties that can be applied to Data Fields are per data field basis or for all data fields. Adding sensitivity field for all als fields, which is most commonly used in currently available sensor hubs. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> --- drivers/iio/light/hid-sensor-als.c | 11 +++++++++++ include/linux/hid-sensor-ids.h | 1 + 2 files changed, 12 insertions(+) diff --git a/drivers/iio/light/hid-sensor-als.c b/drivers/iio/light/hid-sensor-als.c index 8e8b9d7..621541f 100644 --- a/drivers/iio/light/hid-sensor-als.c +++ b/drivers/iio/light/hid-sensor-als.c @@ -229,6 +229,17 @@ static int als_parse_report(struct platform_device *pdev, dev_dbg(&pdev->dev, "als %x:%x\n", st->als_illum.index, st->als_illum.report_id); + /* Set Sensitivity field ids, when there is no individual modifier */ + if (st->common_attributes.sensitivity.index < 0) { + sensor_hub_input_get_attribute_info(hsdev, + HID_FEATURE_REPORT, usage_id, + HID_USAGE_SENSOR_DATA_MOD_CHANGE_SENSITIVITY_ABS | + HID_USAGE_SENSOR_DATA_LIGHT, + &st->common_attributes.sensitivity); + dev_dbg(&pdev->dev, "Sensitivity index:report %d:%d\n", + st->common_attributes.sensitivity.index, + st->common_attributes.sensitivity.report_id); + } return ret; } diff --git a/include/linux/hid-sensor-ids.h b/include/linux/hid-sensor-ids.h index b00ed85..880e3fa 100644 --- a/include/linux/hid-sensor-ids.h +++ b/include/linux/hid-sensor-ids.h @@ -30,6 +30,7 @@ /* ALS (200041) */ #define HID_USAGE_SENSOR_ALS 0x200041 +#define HID_USAGE_SENSOR_DATA_LIGHT 0x2004d0 #define HID_USAGE_SENSOR_LIGHT_ILLUM 0x2004d1 /* Gyro 3D: (200076) */ -- 1.8.3.1 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v4 4/5] iio: hid-sensors: magnetometer : Add sensitivity 2013-11-06 0:11 ` [PATCH v4 1/5] iio: hid-sensors: accelerometer: Add sensitivity Srinivas Pandruvada 2013-11-06 0:11 ` [PATCH v4 2/5] iio: hid-sensors: gyro : " Srinivas Pandruvada 2013-11-06 0:11 ` [PATCH v4 3/5] iio: hid-sensors: light/als " Srinivas Pandruvada @ 2013-11-06 0:11 ` Srinivas Pandruvada 2013-11-09 11:56 ` Jonathan Cameron 2013-11-06 0:11 ` [PATCH v4 5/5] iio: hid-sensors: Added Inclinometer 3D Srinivas Pandruvada 3 siblings, 1 reply; 8+ messages in thread From: Srinivas Pandruvada @ 2013-11-06 0:11 UTC (permalink / raw) To: jic23; +Cc: linux-iio, Srinivas Pandruvada A number of Properties that can be applied to Data Fields are per data field basis or for all data fields. Adding sensitivity field for all magnetometer fields, which is most commonly used in currently available sensor hubs. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> --- drivers/iio/magnetometer/hid-sensor-magn-3d.c | 12 ++++++++++++ include/linux/hid-sensor-ids.h | 1 + 2 files changed, 13 insertions(+) diff --git a/drivers/iio/magnetometer/hid-sensor-magn-3d.c b/drivers/iio/magnetometer/hid-sensor-magn-3d.c index b26e102..6d162b7 100644 --- a/drivers/iio/magnetometer/hid-sensor-magn-3d.c +++ b/drivers/iio/magnetometer/hid-sensor-magn-3d.c @@ -263,6 +263,18 @@ static int magn_3d_parse_report(struct platform_device *pdev, st->magn[1].index, st->magn[1].report_id, st->magn[2].index, st->magn[2].report_id); + /* Set Sensitivity field ids, when there is no individual modifier */ + if (st->common_attributes.sensitivity.index < 0) { + sensor_hub_input_get_attribute_info(hsdev, + HID_FEATURE_REPORT, usage_id, + HID_USAGE_SENSOR_DATA_MOD_CHANGE_SENSITIVITY_ABS | + HID_USAGE_SENSOR_DATA_ORIENTATION, + &st->common_attributes.sensitivity); + dev_dbg(&pdev->dev, "Sensitivity index:report %d:%d\n", + st->common_attributes.sensitivity.index, + st->common_attributes.sensitivity.report_id); + } + return ret; } diff --git a/include/linux/hid-sensor-ids.h b/include/linux/hid-sensor-ids.h index 880e3fa..e6e5fb9 100644 --- a/include/linux/hid-sensor-ids.h +++ b/include/linux/hid-sensor-ids.h @@ -42,6 +42,7 @@ /* ORIENTATION: Compass 3D: (200083) */ #define HID_USAGE_SENSOR_COMPASS_3D 0x200083 +#define HID_USAGE_SENSOR_DATA_ORIENTATION 0x200470 #define HID_USAGE_SENSOR_ORIENT_MAGN_HEADING 0x200471 #define HID_USAGE_SENSOR_ORIENT_MAGN_HEADING_X 0x200472 #define HID_USAGE_SENSOR_ORIENT_MAGN_HEADING_Y 0x200473 -- 1.8.3.1 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v4 4/5] iio: hid-sensors: magnetometer : Add sensitivity 2013-11-06 0:11 ` [PATCH v4 4/5] iio: hid-sensors: magnetometer " Srinivas Pandruvada @ 2013-11-09 11:56 ` Jonathan Cameron 0 siblings, 0 replies; 8+ messages in thread From: Jonathan Cameron @ 2013-11-09 11:56 UTC (permalink / raw) To: Srinivas Pandruvada; +Cc: linux-iio On 11/06/13 00:11, Srinivas Pandruvada wrote: > A number of Properties that can be applied to Data Fields are per data > field basis or for all data fields. Adding sensitivity field for all > magnetometer fields, which is most commonly used in currently available > sensor hubs. > > Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Applied to the togreg branch of iio.git Note the first 3 in this series have already been applied. > --- > drivers/iio/magnetometer/hid-sensor-magn-3d.c | 12 ++++++++++++ > include/linux/hid-sensor-ids.h | 1 + > 2 files changed, 13 insertions(+) > > diff --git a/drivers/iio/magnetometer/hid-sensor-magn-3d.c b/drivers/iio/magnetometer/hid-sensor-magn-3d.c > index b26e102..6d162b7 100644 > --- a/drivers/iio/magnetometer/hid-sensor-magn-3d.c > +++ b/drivers/iio/magnetometer/hid-sensor-magn-3d.c > @@ -263,6 +263,18 @@ static int magn_3d_parse_report(struct platform_device *pdev, > st->magn[1].index, st->magn[1].report_id, > st->magn[2].index, st->magn[2].report_id); > > + /* Set Sensitivity field ids, when there is no individual modifier */ > + if (st->common_attributes.sensitivity.index < 0) { > + sensor_hub_input_get_attribute_info(hsdev, > + HID_FEATURE_REPORT, usage_id, > + HID_USAGE_SENSOR_DATA_MOD_CHANGE_SENSITIVITY_ABS | > + HID_USAGE_SENSOR_DATA_ORIENTATION, > + &st->common_attributes.sensitivity); > + dev_dbg(&pdev->dev, "Sensitivity index:report %d:%d\n", > + st->common_attributes.sensitivity.index, > + st->common_attributes.sensitivity.report_id); > + } > + > return ret; > } > > diff --git a/include/linux/hid-sensor-ids.h b/include/linux/hid-sensor-ids.h > index 880e3fa..e6e5fb9 100644 > --- a/include/linux/hid-sensor-ids.h > +++ b/include/linux/hid-sensor-ids.h > @@ -42,6 +42,7 @@ > > /* ORIENTATION: Compass 3D: (200083) */ > #define HID_USAGE_SENSOR_COMPASS_3D 0x200083 > +#define HID_USAGE_SENSOR_DATA_ORIENTATION 0x200470 > #define HID_USAGE_SENSOR_ORIENT_MAGN_HEADING 0x200471 > #define HID_USAGE_SENSOR_ORIENT_MAGN_HEADING_X 0x200472 > #define HID_USAGE_SENSOR_ORIENT_MAGN_HEADING_Y 0x200473 > ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v4 5/5] iio: hid-sensors: Added Inclinometer 3D 2013-11-06 0:11 ` [PATCH v4 1/5] iio: hid-sensors: accelerometer: Add sensitivity Srinivas Pandruvada ` (2 preceding siblings ...) 2013-11-06 0:11 ` [PATCH v4 4/5] iio: hid-sensors: magnetometer " Srinivas Pandruvada @ 2013-11-06 0:11 ` Srinivas Pandruvada 2013-11-09 12:11 ` Jonathan Cameron 3 siblings, 1 reply; 8+ messages in thread From: Srinivas Pandruvada @ 2013-11-06 0:11 UTC (permalink / raw) To: jic23; +Cc: linux-iio, Srinivas Pandruvada Added usage id processing for Inclinometer 3D. This uses IIO interfaces for triggered buffer to present data to user mode.This uses HID sensor framework for registering callback events from the sensor hub. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> --- drivers/iio/Kconfig | 1 + drivers/iio/Makefile | 1 + drivers/iio/orientation/Kconfig | 19 ++ drivers/iio/orientation/Makefile | 6 + drivers/iio/orientation/hid-sensor-incl-3d.c | 428 +++++++++++++++++++++++++++ include/linux/hid-sensor-ids.h | 4 + 6 files changed, 459 insertions(+) create mode 100644 drivers/iio/orientation/Kconfig create mode 100644 drivers/iio/orientation/Makefile create mode 100644 drivers/iio/orientation/hid-sensor-incl-3d.c diff --git a/drivers/iio/Kconfig b/drivers/iio/Kconfig index 90cf0cd..73ff5bb 100644 --- a/drivers/iio/Kconfig +++ b/drivers/iio/Kconfig @@ -68,6 +68,7 @@ source "drivers/iio/gyro/Kconfig" source "drivers/iio/imu/Kconfig" source "drivers/iio/light/Kconfig" source "drivers/iio/magnetometer/Kconfig" +source "drivers/iio/orientation/Kconfig" if IIO_TRIGGER source "drivers/iio/trigger/Kconfig" endif #IIO_TRIGGER diff --git a/drivers/iio/Makefile b/drivers/iio/Makefile index bcf7e9e..c682e1b 100644 --- a/drivers/iio/Makefile +++ b/drivers/iio/Makefile @@ -21,6 +21,7 @@ obj-y += frequency/ obj-y += imu/ obj-y += light/ obj-y += magnetometer/ +obj-y += orientation/ obj-y += pressure/ obj-y += temperature/ obj-y += trigger/ diff --git a/drivers/iio/orientation/Kconfig b/drivers/iio/orientation/Kconfig new file mode 100644 index 0000000..58c62c8 --- /dev/null +++ b/drivers/iio/orientation/Kconfig @@ -0,0 +1,19 @@ +# +# Inclinometer sensors +# +# When adding new entries keep the list in alphabetical order + +menu "Inclinometer sensors" + +config HID_SENSOR_INCLINOMETER_3D + depends on HID_SENSOR_HUB + select IIO_BUFFER + select IIO_TRIGGERED_BUFFER + select HID_SENSOR_IIO_COMMON + select HID_SENSOR_IIO_TRIGGER + tristate "HID Inclinometer 3D" + help + Say yes here to build support for the HID SENSOR + Inclinometer 3D. + +endmenu diff --git a/drivers/iio/orientation/Makefile b/drivers/iio/orientation/Makefile new file mode 100644 index 0000000..2c97572 --- /dev/null +++ b/drivers/iio/orientation/Makefile @@ -0,0 +1,6 @@ +# +# Makefile for industrial I/O Inclinometer sensor drivers +# + +# When adding new entries keep the list in alphabetical order +obj-$(CONFIG_HID_SENSOR_INCLINOMETER_3D) += hid-sensor-incl-3d.o diff --git a/drivers/iio/orientation/hid-sensor-incl-3d.c b/drivers/iio/orientation/hid-sensor-incl-3d.c new file mode 100644 index 0000000..070feab --- /dev/null +++ b/drivers/iio/orientation/hid-sensor-incl-3d.c @@ -0,0 +1,428 @@ +/* + * HID Sensors Driver + * Copyright (c) 2013, Intel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc. + * + */ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/irq.h> +#include <linux/slab.h> +#include <linux/hid-sensor-hub.h> +#include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> +#include <linux/iio/buffer.h> +#include <linux/iio/trigger_consumer.h> +#include <linux/iio/triggered_buffer.h> +#include "../common/hid-sensors/hid-sensor-trigger.h" + +enum incl_3d_channel { + CHANNEL_SCAN_INDEX_X, + CHANNEL_SCAN_INDEX_Y, + CHANNEL_SCAN_INDEX_Z, + INCLI_3D_CHANNEL_MAX, +}; + +struct incl_3d_state { + struct hid_sensor_hub_callbacks callbacks; + struct hid_sensor_common common_attributes; + struct hid_sensor_hub_attribute_info incl[INCLI_3D_CHANNEL_MAX]; + u32 incl_val[INCLI_3D_CHANNEL_MAX]; +}; + +static const u32 incl_3d_addresses[INCLI_3D_CHANNEL_MAX] = { + HID_USAGE_SENSOR_ORIENT_TILT_X, + HID_USAGE_SENSOR_ORIENT_TILT_Y, + HID_USAGE_SENSOR_ORIENT_TILT_Z +}; + +/* Channel definitions */ +static const struct iio_chan_spec incl_3d_channels[] = { + { + .type = IIO_INCLI, + .modified = 1, + .channel2 = IIO_MOD_X, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | + BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_SAMP_FREQ) | + BIT(IIO_CHAN_INFO_HYSTERESIS), + .scan_index = CHANNEL_SCAN_INDEX_X, + }, { + .type = IIO_INCLI, + .modified = 1, + .channel2 = IIO_MOD_Y, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | + BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_SAMP_FREQ) | + BIT(IIO_CHAN_INFO_HYSTERESIS), + .scan_index = CHANNEL_SCAN_INDEX_Y, + }, { + .type = IIO_INCLI, + .modified = 1, + .channel2 = IIO_MOD_Z, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | + BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_SAMP_FREQ) | + BIT(IIO_CHAN_INFO_HYSTERESIS), + .scan_index = CHANNEL_SCAN_INDEX_Z, + } +}; + +/* Adjust channel real bits based on report descriptor */ +static void incl_3d_adjust_channel_bit_mask(struct iio_chan_spec *chan, + int size) +{ + chan->scan_type.sign = 's'; + /* Real storage bits will change based on the report desc. */ + chan->scan_type.realbits = size * 8; + /* Maximum size of a sample to capture is u32 */ + chan->scan_type.storagebits = sizeof(u32) * 8; +} + +/* Channel read_raw handler */ +static int incl_3d_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, + long mask) +{ + struct incl_3d_state *incl_state = iio_priv(indio_dev); + int report_id = -1; + u32 address; + int ret_type; + + *val = 0; + *val2 = 0; + switch (mask) { + case IIO_CHAN_INFO_RAW: + report_id = + incl_state->incl[chan->scan_index].report_id; + address = incl_3d_addresses[chan->scan_index]; + if (report_id >= 0) + *val = sensor_hub_input_attr_get_raw_value( + incl_state->common_attributes.hsdev, + HID_USAGE_SENSOR_INCLINOMETER_3D, address, + report_id); + else { + return -EINVAL; + } + ret_type = IIO_VAL_INT; + break; + case IIO_CHAN_INFO_SCALE: + *val = incl_state->incl[CHANNEL_SCAN_INDEX_X].units; + ret_type = IIO_VAL_INT; + break; + case IIO_CHAN_INFO_OFFSET: + *val = hid_sensor_convert_exponent( + incl_state->incl[CHANNEL_SCAN_INDEX_X].unit_expo); + ret_type = IIO_VAL_INT; + break; + case IIO_CHAN_INFO_SAMP_FREQ: + ret_type = hid_sensor_read_samp_freq_value( + &incl_state->common_attributes, val, val2); + break; + case IIO_CHAN_INFO_HYSTERESIS: + ret_type = hid_sensor_read_raw_hyst_value( + &incl_state->common_attributes, val, val2); + break; + default: + ret_type = -EINVAL; + break; + } + + return ret_type; +} + +/* Channel write_raw handler */ +static int incl_3d_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int val, + int val2, + long mask) +{ + struct incl_3d_state *incl_state = iio_priv(indio_dev); + int ret; + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + ret = hid_sensor_write_samp_freq_value( + &incl_state->common_attributes, val, val2); + break; + case IIO_CHAN_INFO_HYSTERESIS: + ret = hid_sensor_write_raw_hyst_value( + &incl_state->common_attributes, val, val2); + break; + default: + ret = -EINVAL; + } + + return ret; +} + +static const struct iio_info incl_3d_info = { + .driver_module = THIS_MODULE, + .read_raw = &incl_3d_read_raw, + .write_raw = &incl_3d_write_raw, +}; + +/* Function to push data to buffer */ +static void hid_sensor_push_data(struct iio_dev *indio_dev, u8 *data, int len) +{ + dev_dbg(&indio_dev->dev, "hid_sensor_push_data\n"); + iio_push_to_buffers(indio_dev, (u8 *)data); +} + +/* Callback handler to send event after all samples are received and captured */ +static int incl_3d_proc_event(struct hid_sensor_hub_device *hsdev, + unsigned usage_id, + void *priv) +{ + struct iio_dev *indio_dev = platform_get_drvdata(priv); + struct incl_3d_state *incl_state = iio_priv(indio_dev); + + dev_dbg(&indio_dev->dev, "incl_3d_proc_event [%d]\n", + incl_state->common_attributes.data_ready); + if (incl_state->common_attributes.data_ready) + hid_sensor_push_data(indio_dev, + (u8 *)incl_state->incl_val, + sizeof(incl_state->incl_val)); + + return 0; +} + +/* Capture samples in local storage */ +static int incl_3d_capture_sample(struct hid_sensor_hub_device *hsdev, + unsigned usage_id, + size_t raw_len, char *raw_data, + void *priv) +{ + struct iio_dev *indio_dev = platform_get_drvdata(priv); + struct incl_3d_state *incl_state = iio_priv(indio_dev); + int ret = 0; + + switch (usage_id) { + case HID_USAGE_SENSOR_ORIENT_TILT_X: + incl_state->incl_val[CHANNEL_SCAN_INDEX_X] = *(u32 *)raw_data; + break; + case HID_USAGE_SENSOR_ORIENT_TILT_Y: + incl_state->incl_val[CHANNEL_SCAN_INDEX_Y] = *(u32 *)raw_data; + break; + case HID_USAGE_SENSOR_ORIENT_TILT_Z: + incl_state->incl_val[CHANNEL_SCAN_INDEX_Z] = *(u32 *)raw_data; + break; + default: + ret = -EINVAL; + break; + } + + return ret; +} + +/* Parse report which is specific to an usage id*/ +static int incl_3d_parse_report(struct platform_device *pdev, + struct hid_sensor_hub_device *hsdev, + struct iio_chan_spec *channels, + unsigned usage_id, + struct incl_3d_state *st) +{ + int ret; + + ret = sensor_hub_input_get_attribute_info(hsdev, + HID_INPUT_REPORT, + usage_id, + HID_USAGE_SENSOR_ORIENT_TILT_X, + &st->incl[CHANNEL_SCAN_INDEX_X]); + if (ret) + return ret; + incl_3d_adjust_channel_bit_mask(&channels[CHANNEL_SCAN_INDEX_X], + st->incl[CHANNEL_SCAN_INDEX_X].size); + + ret = sensor_hub_input_get_attribute_info(hsdev, + HID_INPUT_REPORT, + usage_id, + HID_USAGE_SENSOR_ORIENT_TILT_Y, + &st->incl[CHANNEL_SCAN_INDEX_Y]); + if (ret) + return ret; + incl_3d_adjust_channel_bit_mask(&channels[CHANNEL_SCAN_INDEX_Y], + st->incl[CHANNEL_SCAN_INDEX_Y].size); + + ret = sensor_hub_input_get_attribute_info(hsdev, + HID_INPUT_REPORT, + usage_id, + HID_USAGE_SENSOR_ORIENT_TILT_Z, + &st->incl[CHANNEL_SCAN_INDEX_Z]); + if (ret) + return ret; + incl_3d_adjust_channel_bit_mask(&channels[CHANNEL_SCAN_INDEX_Z], + st->incl[CHANNEL_SCAN_INDEX_Z].size); + + dev_dbg(&pdev->dev, "incl_3d %x:%x, %x:%x, %x:%x\n", + st->incl[0].index, + st->incl[0].report_id, + st->incl[1].index, st->incl[1].report_id, + st->incl[2].index, st->incl[2].report_id); + + /* Set Sensitivity field ids, when there is no individual modifier */ + if (st->common_attributes.sensitivity.index < 0) { + sensor_hub_input_get_attribute_info(hsdev, + HID_FEATURE_REPORT, usage_id, + HID_USAGE_SENSOR_DATA_MOD_CHANGE_SENSITIVITY_ABS | + HID_USAGE_SENSOR_DATA_ORIENTATION, + &st->common_attributes.sensitivity); + dev_dbg(&pdev->dev, "Sensitivity index:report %d:%d\n", + st->common_attributes.sensitivity.index, + st->common_attributes.sensitivity.report_id); + } + return ret; +} + +/* Function to initialize the processing for usage id */ +static int hid_incl_3d_probe(struct platform_device *pdev) +{ + int ret; + static char *name = "incli_3d"; + struct iio_dev *indio_dev; + struct incl_3d_state *incl_state; + struct hid_sensor_hub_device *hsdev = pdev->dev.platform_data; + struct iio_chan_spec *channels; + + indio_dev = devm_iio_device_alloc(&pdev->dev, + sizeof(struct incl_3d_state)); + if (indio_dev == NULL) + return -ENOMEM; + + platform_set_drvdata(pdev, indio_dev); + + incl_state = iio_priv(indio_dev); + incl_state->common_attributes.hsdev = hsdev; + incl_state->common_attributes.pdev = pdev; + + ret = hid_sensor_parse_common_attributes(hsdev, + HID_USAGE_SENSOR_INCLINOMETER_3D, + &incl_state->common_attributes); + if (ret) { + dev_err(&pdev->dev, "failed to setup common attributes\n"); + return ret; + } + + channels = kmemdup(incl_3d_channels, sizeof(incl_3d_channels), + GFP_KERNEL); + if (!channels) { + dev_err(&pdev->dev, "failed to duplicate channels\n"); + return -ENOMEM; + } + + ret = incl_3d_parse_report(pdev, hsdev, channels, + HID_USAGE_SENSOR_INCLINOMETER_3D, incl_state); + if (ret) { + dev_err(&pdev->dev, "failed to setup attributes\n"); + goto error_free_dev_mem; + } + + indio_dev->channels = channels; + indio_dev->num_channels = ARRAY_SIZE(incl_3d_channels); + indio_dev->dev.parent = &pdev->dev; + indio_dev->info = &incl_3d_info; + indio_dev->name = name; + indio_dev->modes = INDIO_DIRECT_MODE; + + ret = iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time, + NULL, NULL); + if (ret) { + dev_err(&pdev->dev, "failed to initialize trigger buffer\n"); + goto error_free_dev_mem; + } + incl_state->common_attributes.data_ready = false; + ret = hid_sensor_setup_trigger(indio_dev, name, + &incl_state->common_attributes); + if (ret) { + dev_err(&pdev->dev, "trigger setup failed\n"); + goto error_unreg_buffer_funcs; + } + + ret = iio_device_register(indio_dev); + if (ret) { + dev_err(&pdev->dev, "device register failed\n"); + goto error_remove_trigger; + } + + incl_state->callbacks.send_event = incl_3d_proc_event; + incl_state->callbacks.capture_sample = incl_3d_capture_sample; + incl_state->callbacks.pdev = pdev; + ret = sensor_hub_register_callback(hsdev, + HID_USAGE_SENSOR_INCLINOMETER_3D, + &incl_state->callbacks); + if (ret) { + dev_err(&pdev->dev, "callback reg failed\n"); + goto error_iio_unreg; + } + + return 0; + +error_iio_unreg: + iio_device_unregister(indio_dev); +error_remove_trigger: + hid_sensor_remove_trigger(&incl_state->common_attributes); +error_unreg_buffer_funcs: + iio_triggered_buffer_cleanup(indio_dev); +error_free_dev_mem: + kfree(indio_dev->channels); + return ret; +} + +/* Function to deinitialize the processing for usage id */ +static int hid_incl_3d_remove(struct platform_device *pdev) +{ + struct hid_sensor_hub_device *hsdev = pdev->dev.platform_data; + struct iio_dev *indio_dev = platform_get_drvdata(pdev); + struct incl_3d_state *incl_state = iio_priv(indio_dev); + + sensor_hub_remove_callback(hsdev, HID_USAGE_SENSOR_INCLINOMETER_3D); + iio_device_unregister(indio_dev); + hid_sensor_remove_trigger(&incl_state->common_attributes); + iio_triggered_buffer_cleanup(indio_dev); + kfree(indio_dev->channels); + + return 0; +} + +static struct platform_device_id hid_incl_3d_ids[] = { + { + /* Format: HID-SENSOR-usage_id_in_hex_lowercase */ + .name = "HID-SENSOR-200086", + }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(platform, hid_incl_3d_ids); + +static struct platform_driver hid_incl_3d_platform_driver = { + .id_table = hid_incl_3d_ids, + .driver = { + .name = KBUILD_MODNAME, + .owner = THIS_MODULE, + }, + .probe = hid_incl_3d_probe, + .remove = hid_incl_3d_remove, +}; +module_platform_driver(hid_incl_3d_platform_driver); + +MODULE_DESCRIPTION("HID Sensor Inclinometer 3D"); +MODULE_AUTHOR("Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>"); +MODULE_LICENSE("GPL"); diff --git a/include/linux/hid-sensor-ids.h b/include/linux/hid-sensor-ids.h index e6e5fb9..0232055 100644 --- a/include/linux/hid-sensor-ids.h +++ b/include/linux/hid-sensor-ids.h @@ -58,10 +58,14 @@ #define HID_USAGE_SENSOR_ORIENT_DISTANCE_Y 0x20047B #define HID_USAGE_SENSOR_ORIENT_DISTANCE_Z 0x20047C #define HID_USAGE_SENSOR_ORIENT_DISTANCE_OUT_OF_RANGE 0x20047D + +/* ORIENTATION: Inclinometer 3D: (200086) */ +#define HID_USAGE_SENSOR_INCLINOMETER_3D 0x200086 #define HID_USAGE_SENSOR_ORIENT_TILT 0x20047E #define HID_USAGE_SENSOR_ORIENT_TILT_X 0x20047F #define HID_USAGE_SENSOR_ORIENT_TILT_Y 0x200480 #define HID_USAGE_SENSOR_ORIENT_TILT_Z 0x200481 + #define HID_USAGE_SENSOR_ORIENT_ROTATION_MATRIX 0x200482 #define HID_USAGE_SENSOR_ORIENT_QUATERNION 0x200483 #define HID_USAGE_SENSOR_ORIENT_MAGN_FLUX 0x200484 -- 1.8.3.1 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v4 5/5] iio: hid-sensors: Added Inclinometer 3D 2013-11-06 0:11 ` [PATCH v4 5/5] iio: hid-sensors: Added Inclinometer 3D Srinivas Pandruvada @ 2013-11-09 12:11 ` Jonathan Cameron 2013-12-03 20:37 ` Jonathan Cameron 0 siblings, 1 reply; 8+ messages in thread From: Jonathan Cameron @ 2013-11-09 12:11 UTC (permalink / raw) To: Srinivas Pandruvada; +Cc: linux-iio, Lars-Peter Clausen, Peter Meerwald On 11/06/13 00:11, Srinivas Pandruvada wrote: > Added usage id processing for Inclinometer 3D. This uses IIO > interfaces for triggered buffer to present data to user > mode.This uses HID sensor framework for registering callback > events from the sensor hub. > > Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> The driver is fine. One remaining question is where this driver (and similar ones should be located). What groups make sense? Inclinometers are mostly (if not all?) accelerometer based. Should we put them in the accelerometer group or are our current groups no ideal? I have applied this as presented as I suspect we need to have a more general reorganization. What do others think? Anyhow, applied to the togreg branch of iio.git Thanks, Jonathan > --- > drivers/iio/Kconfig | 1 + > drivers/iio/Makefile | 1 + > drivers/iio/orientation/Kconfig | 19 ++ > drivers/iio/orientation/Makefile | 6 + > drivers/iio/orientation/hid-sensor-incl-3d.c | 428 +++++++++++++++++++++++++++ > include/linux/hid-sensor-ids.h | 4 + > 6 files changed, 459 insertions(+) > create mode 100644 drivers/iio/orientation/Kconfig > create mode 100644 drivers/iio/orientation/Makefile > create mode 100644 drivers/iio/orientation/hid-sensor-incl-3d.c > > diff --git a/drivers/iio/Kconfig b/drivers/iio/Kconfig > index 90cf0cd..73ff5bb 100644 > --- a/drivers/iio/Kconfig > +++ b/drivers/iio/Kconfig > @@ -68,6 +68,7 @@ source "drivers/iio/gyro/Kconfig" > source "drivers/iio/imu/Kconfig" > source "drivers/iio/light/Kconfig" > source "drivers/iio/magnetometer/Kconfig" > +source "drivers/iio/orientation/Kconfig" > if IIO_TRIGGER > source "drivers/iio/trigger/Kconfig" > endif #IIO_TRIGGER > diff --git a/drivers/iio/Makefile b/drivers/iio/Makefile > index bcf7e9e..c682e1b 100644 > --- a/drivers/iio/Makefile > +++ b/drivers/iio/Makefile > @@ -21,6 +21,7 @@ obj-y += frequency/ > obj-y += imu/ > obj-y += light/ > obj-y += magnetometer/ > +obj-y += orientation/ > obj-y += pressure/ > obj-y += temperature/ > obj-y += trigger/ > diff --git a/drivers/iio/orientation/Kconfig b/drivers/iio/orientation/Kconfig > new file mode 100644 > index 0000000..58c62c8 > --- /dev/null > +++ b/drivers/iio/orientation/Kconfig > @@ -0,0 +1,19 @@ > +# > +# Inclinometer sensors > +# > +# When adding new entries keep the list in alphabetical order > + > +menu "Inclinometer sensors" > + > +config HID_SENSOR_INCLINOMETER_3D > + depends on HID_SENSOR_HUB > + select IIO_BUFFER > + select IIO_TRIGGERED_BUFFER > + select HID_SENSOR_IIO_COMMON > + select HID_SENSOR_IIO_TRIGGER > + tristate "HID Inclinometer 3D" > + help > + Say yes here to build support for the HID SENSOR > + Inclinometer 3D. > + > +endmenu > diff --git a/drivers/iio/orientation/Makefile b/drivers/iio/orientation/Makefile > new file mode 100644 > index 0000000..2c97572 > --- /dev/null > +++ b/drivers/iio/orientation/Makefile > @@ -0,0 +1,6 @@ > +# > +# Makefile for industrial I/O Inclinometer sensor drivers > +# > + > +# When adding new entries keep the list in alphabetical order > +obj-$(CONFIG_HID_SENSOR_INCLINOMETER_3D) += hid-sensor-incl-3d.o > diff --git a/drivers/iio/orientation/hid-sensor-incl-3d.c b/drivers/iio/orientation/hid-sensor-incl-3d.c > new file mode 100644 > index 0000000..070feab > --- /dev/null > +++ b/drivers/iio/orientation/hid-sensor-incl-3d.c > @@ -0,0 +1,428 @@ > +/* > + * HID Sensors Driver > + * Copyright (c) 2013, Intel Corporation. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms and conditions of the GNU General Public License, > + * version 2, as published by the Free Software Foundation. > + * > + * This program is distributed in the hope it will be useful, but WITHOUT > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for > + * more details. > + * > + * You should have received a copy of the GNU General Public License along with > + * this program; if not, write to the Free Software Foundation, Inc. > + * > + */ > + > +#include <linux/device.h> > +#include <linux/platform_device.h> > +#include <linux/module.h> > +#include <linux/interrupt.h> > +#include <linux/irq.h> > +#include <linux/slab.h> > +#include <linux/hid-sensor-hub.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/sysfs.h> > +#include <linux/iio/buffer.h> > +#include <linux/iio/trigger_consumer.h> > +#include <linux/iio/triggered_buffer.h> > +#include "../common/hid-sensors/hid-sensor-trigger.h" > + > +enum incl_3d_channel { > + CHANNEL_SCAN_INDEX_X, > + CHANNEL_SCAN_INDEX_Y, > + CHANNEL_SCAN_INDEX_Z, > + INCLI_3D_CHANNEL_MAX, > +}; > + > +struct incl_3d_state { > + struct hid_sensor_hub_callbacks callbacks; > + struct hid_sensor_common common_attributes; > + struct hid_sensor_hub_attribute_info incl[INCLI_3D_CHANNEL_MAX]; > + u32 incl_val[INCLI_3D_CHANNEL_MAX]; > +}; > + > +static const u32 incl_3d_addresses[INCLI_3D_CHANNEL_MAX] = { > + HID_USAGE_SENSOR_ORIENT_TILT_X, > + HID_USAGE_SENSOR_ORIENT_TILT_Y, > + HID_USAGE_SENSOR_ORIENT_TILT_Z > +}; > + > +/* Channel definitions */ > +static const struct iio_chan_spec incl_3d_channels[] = { > + { > + .type = IIO_INCLI, > + .modified = 1, > + .channel2 = IIO_MOD_X, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | > + BIT(IIO_CHAN_INFO_SCALE) | > + BIT(IIO_CHAN_INFO_SAMP_FREQ) | > + BIT(IIO_CHAN_INFO_HYSTERESIS), > + .scan_index = CHANNEL_SCAN_INDEX_X, > + }, { > + .type = IIO_INCLI, > + .modified = 1, > + .channel2 = IIO_MOD_Y, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | > + BIT(IIO_CHAN_INFO_SCALE) | > + BIT(IIO_CHAN_INFO_SAMP_FREQ) | > + BIT(IIO_CHAN_INFO_HYSTERESIS), > + .scan_index = CHANNEL_SCAN_INDEX_Y, > + }, { > + .type = IIO_INCLI, > + .modified = 1, > + .channel2 = IIO_MOD_Z, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | > + BIT(IIO_CHAN_INFO_SCALE) | > + BIT(IIO_CHAN_INFO_SAMP_FREQ) | > + BIT(IIO_CHAN_INFO_HYSTERESIS), > + .scan_index = CHANNEL_SCAN_INDEX_Z, > + } > +}; > + > +/* Adjust channel real bits based on report descriptor */ > +static void incl_3d_adjust_channel_bit_mask(struct iio_chan_spec *chan, > + int size) > +{ > + chan->scan_type.sign = 's'; > + /* Real storage bits will change based on the report desc. */ > + chan->scan_type.realbits = size * 8; > + /* Maximum size of a sample to capture is u32 */ > + chan->scan_type.storagebits = sizeof(u32) * 8; > +} > + > +/* Channel read_raw handler */ > +static int incl_3d_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, > + int *val, int *val2, > + long mask) > +{ > + struct incl_3d_state *incl_state = iio_priv(indio_dev); > + int report_id = -1; > + u32 address; > + int ret_type; > + > + *val = 0; > + *val2 = 0; > + switch (mask) { > + case IIO_CHAN_INFO_RAW: > + report_id = > + incl_state->incl[chan->scan_index].report_id; > + address = incl_3d_addresses[chan->scan_index]; > + if (report_id >= 0) > + *val = sensor_hub_input_attr_get_raw_value( > + incl_state->common_attributes.hsdev, > + HID_USAGE_SENSOR_INCLINOMETER_3D, address, > + report_id); > + else { > + return -EINVAL; > + } > + ret_type = IIO_VAL_INT; > + break; > + case IIO_CHAN_INFO_SCALE: > + *val = incl_state->incl[CHANNEL_SCAN_INDEX_X].units; > + ret_type = IIO_VAL_INT; > + break; > + case IIO_CHAN_INFO_OFFSET: > + *val = hid_sensor_convert_exponent( > + incl_state->incl[CHANNEL_SCAN_INDEX_X].unit_expo); > + ret_type = IIO_VAL_INT; > + break; > + case IIO_CHAN_INFO_SAMP_FREQ: > + ret_type = hid_sensor_read_samp_freq_value( > + &incl_state->common_attributes, val, val2); > + break; > + case IIO_CHAN_INFO_HYSTERESIS: > + ret_type = hid_sensor_read_raw_hyst_value( > + &incl_state->common_attributes, val, val2); > + break; > + default: > + ret_type = -EINVAL; > + break; > + } > + > + return ret_type; > +} > + > +/* Channel write_raw handler */ > +static int incl_3d_write_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, > + int val, > + int val2, > + long mask) > +{ > + struct incl_3d_state *incl_state = iio_priv(indio_dev); > + int ret; > + > + switch (mask) { > + case IIO_CHAN_INFO_SAMP_FREQ: > + ret = hid_sensor_write_samp_freq_value( > + &incl_state->common_attributes, val, val2); > + break; > + case IIO_CHAN_INFO_HYSTERESIS: > + ret = hid_sensor_write_raw_hyst_value( > + &incl_state->common_attributes, val, val2); > + break; > + default: > + ret = -EINVAL; > + } > + > + return ret; > +} > + > +static const struct iio_info incl_3d_info = { > + .driver_module = THIS_MODULE, > + .read_raw = &incl_3d_read_raw, > + .write_raw = &incl_3d_write_raw, > +}; > + > +/* Function to push data to buffer */ > +static void hid_sensor_push_data(struct iio_dev *indio_dev, u8 *data, int len) > +{ > + dev_dbg(&indio_dev->dev, "hid_sensor_push_data\n"); > + iio_push_to_buffers(indio_dev, (u8 *)data); > +} > + > +/* Callback handler to send event after all samples are received and captured */ > +static int incl_3d_proc_event(struct hid_sensor_hub_device *hsdev, > + unsigned usage_id, > + void *priv) > +{ > + struct iio_dev *indio_dev = platform_get_drvdata(priv); > + struct incl_3d_state *incl_state = iio_priv(indio_dev); > + > + dev_dbg(&indio_dev->dev, "incl_3d_proc_event [%d]\n", > + incl_state->common_attributes.data_ready); > + if (incl_state->common_attributes.data_ready) > + hid_sensor_push_data(indio_dev, > + (u8 *)incl_state->incl_val, > + sizeof(incl_state->incl_val)); > + > + return 0; > +} > + > +/* Capture samples in local storage */ > +static int incl_3d_capture_sample(struct hid_sensor_hub_device *hsdev, > + unsigned usage_id, > + size_t raw_len, char *raw_data, > + void *priv) > +{ > + struct iio_dev *indio_dev = platform_get_drvdata(priv); > + struct incl_3d_state *incl_state = iio_priv(indio_dev); > + int ret = 0; > + > + switch (usage_id) { > + case HID_USAGE_SENSOR_ORIENT_TILT_X: > + incl_state->incl_val[CHANNEL_SCAN_INDEX_X] = *(u32 *)raw_data; > + break; > + case HID_USAGE_SENSOR_ORIENT_TILT_Y: > + incl_state->incl_val[CHANNEL_SCAN_INDEX_Y] = *(u32 *)raw_data; > + break; > + case HID_USAGE_SENSOR_ORIENT_TILT_Z: > + incl_state->incl_val[CHANNEL_SCAN_INDEX_Z] = *(u32 *)raw_data; > + break; > + default: > + ret = -EINVAL; > + break; > + } > + > + return ret; > +} > + > +/* Parse report which is specific to an usage id*/ > +static int incl_3d_parse_report(struct platform_device *pdev, > + struct hid_sensor_hub_device *hsdev, > + struct iio_chan_spec *channels, > + unsigned usage_id, > + struct incl_3d_state *st) > +{ > + int ret; > + > + ret = sensor_hub_input_get_attribute_info(hsdev, > + HID_INPUT_REPORT, > + usage_id, > + HID_USAGE_SENSOR_ORIENT_TILT_X, > + &st->incl[CHANNEL_SCAN_INDEX_X]); > + if (ret) > + return ret; > + incl_3d_adjust_channel_bit_mask(&channels[CHANNEL_SCAN_INDEX_X], > + st->incl[CHANNEL_SCAN_INDEX_X].size); > + > + ret = sensor_hub_input_get_attribute_info(hsdev, > + HID_INPUT_REPORT, > + usage_id, > + HID_USAGE_SENSOR_ORIENT_TILT_Y, > + &st->incl[CHANNEL_SCAN_INDEX_Y]); > + if (ret) > + return ret; > + incl_3d_adjust_channel_bit_mask(&channels[CHANNEL_SCAN_INDEX_Y], > + st->incl[CHANNEL_SCAN_INDEX_Y].size); > + > + ret = sensor_hub_input_get_attribute_info(hsdev, > + HID_INPUT_REPORT, > + usage_id, > + HID_USAGE_SENSOR_ORIENT_TILT_Z, > + &st->incl[CHANNEL_SCAN_INDEX_Z]); > + if (ret) > + return ret; > + incl_3d_adjust_channel_bit_mask(&channels[CHANNEL_SCAN_INDEX_Z], > + st->incl[CHANNEL_SCAN_INDEX_Z].size); > + > + dev_dbg(&pdev->dev, "incl_3d %x:%x, %x:%x, %x:%x\n", > + st->incl[0].index, > + st->incl[0].report_id, > + st->incl[1].index, st->incl[1].report_id, > + st->incl[2].index, st->incl[2].report_id); > + > + /* Set Sensitivity field ids, when there is no individual modifier */ > + if (st->common_attributes.sensitivity.index < 0) { > + sensor_hub_input_get_attribute_info(hsdev, > + HID_FEATURE_REPORT, usage_id, > + HID_USAGE_SENSOR_DATA_MOD_CHANGE_SENSITIVITY_ABS | > + HID_USAGE_SENSOR_DATA_ORIENTATION, > + &st->common_attributes.sensitivity); > + dev_dbg(&pdev->dev, "Sensitivity index:report %d:%d\n", > + st->common_attributes.sensitivity.index, > + st->common_attributes.sensitivity.report_id); > + } > + return ret; > +} > + > +/* Function to initialize the processing for usage id */ > +static int hid_incl_3d_probe(struct platform_device *pdev) > +{ > + int ret; > + static char *name = "incli_3d"; > + struct iio_dev *indio_dev; > + struct incl_3d_state *incl_state; > + struct hid_sensor_hub_device *hsdev = pdev->dev.platform_data; > + struct iio_chan_spec *channels; > + > + indio_dev = devm_iio_device_alloc(&pdev->dev, > + sizeof(struct incl_3d_state)); > + if (indio_dev == NULL) > + return -ENOMEM; > + > + platform_set_drvdata(pdev, indio_dev); > + > + incl_state = iio_priv(indio_dev); > + incl_state->common_attributes.hsdev = hsdev; > + incl_state->common_attributes.pdev = pdev; > + > + ret = hid_sensor_parse_common_attributes(hsdev, > + HID_USAGE_SENSOR_INCLINOMETER_3D, > + &incl_state->common_attributes); > + if (ret) { > + dev_err(&pdev->dev, "failed to setup common attributes\n"); > + return ret; > + } > + > + channels = kmemdup(incl_3d_channels, sizeof(incl_3d_channels), > + GFP_KERNEL); > + if (!channels) { > + dev_err(&pdev->dev, "failed to duplicate channels\n"); > + return -ENOMEM; > + } > + > + ret = incl_3d_parse_report(pdev, hsdev, channels, > + HID_USAGE_SENSOR_INCLINOMETER_3D, incl_state); > + if (ret) { > + dev_err(&pdev->dev, "failed to setup attributes\n"); > + goto error_free_dev_mem; > + } > + > + indio_dev->channels = channels; > + indio_dev->num_channels = ARRAY_SIZE(incl_3d_channels); > + indio_dev->dev.parent = &pdev->dev; > + indio_dev->info = &incl_3d_info; > + indio_dev->name = name; > + indio_dev->modes = INDIO_DIRECT_MODE; > + > + ret = iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time, > + NULL, NULL); > + if (ret) { > + dev_err(&pdev->dev, "failed to initialize trigger buffer\n"); > + goto error_free_dev_mem; > + } > + incl_state->common_attributes.data_ready = false; > + ret = hid_sensor_setup_trigger(indio_dev, name, > + &incl_state->common_attributes); > + if (ret) { > + dev_err(&pdev->dev, "trigger setup failed\n"); > + goto error_unreg_buffer_funcs; > + } > + > + ret = iio_device_register(indio_dev); > + if (ret) { > + dev_err(&pdev->dev, "device register failed\n"); > + goto error_remove_trigger; > + } > + > + incl_state->callbacks.send_event = incl_3d_proc_event; > + incl_state->callbacks.capture_sample = incl_3d_capture_sample; > + incl_state->callbacks.pdev = pdev; > + ret = sensor_hub_register_callback(hsdev, > + HID_USAGE_SENSOR_INCLINOMETER_3D, > + &incl_state->callbacks); > + if (ret) { > + dev_err(&pdev->dev, "callback reg failed\n"); > + goto error_iio_unreg; > + } > + > + return 0; > + > +error_iio_unreg: > + iio_device_unregister(indio_dev); > +error_remove_trigger: > + hid_sensor_remove_trigger(&incl_state->common_attributes); > +error_unreg_buffer_funcs: > + iio_triggered_buffer_cleanup(indio_dev); > +error_free_dev_mem: > + kfree(indio_dev->channels); > + return ret; > +} > + > +/* Function to deinitialize the processing for usage id */ > +static int hid_incl_3d_remove(struct platform_device *pdev) > +{ > + struct hid_sensor_hub_device *hsdev = pdev->dev.platform_data; > + struct iio_dev *indio_dev = platform_get_drvdata(pdev); > + struct incl_3d_state *incl_state = iio_priv(indio_dev); > + > + sensor_hub_remove_callback(hsdev, HID_USAGE_SENSOR_INCLINOMETER_3D); > + iio_device_unregister(indio_dev); > + hid_sensor_remove_trigger(&incl_state->common_attributes); > + iio_triggered_buffer_cleanup(indio_dev); > + kfree(indio_dev->channels); > + > + return 0; > +} > + > +static struct platform_device_id hid_incl_3d_ids[] = { > + { > + /* Format: HID-SENSOR-usage_id_in_hex_lowercase */ > + .name = "HID-SENSOR-200086", > + }, > + { /* sentinel */ } > +}; > +MODULE_DEVICE_TABLE(platform, hid_incl_3d_ids); > + > +static struct platform_driver hid_incl_3d_platform_driver = { > + .id_table = hid_incl_3d_ids, > + .driver = { > + .name = KBUILD_MODNAME, > + .owner = THIS_MODULE, > + }, > + .probe = hid_incl_3d_probe, > + .remove = hid_incl_3d_remove, > +}; > +module_platform_driver(hid_incl_3d_platform_driver); > + > +MODULE_DESCRIPTION("HID Sensor Inclinometer 3D"); > +MODULE_AUTHOR("Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>"); > +MODULE_LICENSE("GPL"); > diff --git a/include/linux/hid-sensor-ids.h b/include/linux/hid-sensor-ids.h > index e6e5fb9..0232055 100644 > --- a/include/linux/hid-sensor-ids.h > +++ b/include/linux/hid-sensor-ids.h > @@ -58,10 +58,14 @@ > #define HID_USAGE_SENSOR_ORIENT_DISTANCE_Y 0x20047B > #define HID_USAGE_SENSOR_ORIENT_DISTANCE_Z 0x20047C > #define HID_USAGE_SENSOR_ORIENT_DISTANCE_OUT_OF_RANGE 0x20047D > + > +/* ORIENTATION: Inclinometer 3D: (200086) */ > +#define HID_USAGE_SENSOR_INCLINOMETER_3D 0x200086 > #define HID_USAGE_SENSOR_ORIENT_TILT 0x20047E > #define HID_USAGE_SENSOR_ORIENT_TILT_X 0x20047F > #define HID_USAGE_SENSOR_ORIENT_TILT_Y 0x200480 > #define HID_USAGE_SENSOR_ORIENT_TILT_Z 0x200481 > + > #define HID_USAGE_SENSOR_ORIENT_ROTATION_MATRIX 0x200482 > #define HID_USAGE_SENSOR_ORIENT_QUATERNION 0x200483 > #define HID_USAGE_SENSOR_ORIENT_MAGN_FLUX 0x200484 > ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v4 5/5] iio: hid-sensors: Added Inclinometer 3D 2013-11-09 12:11 ` Jonathan Cameron @ 2013-12-03 20:37 ` Jonathan Cameron 0 siblings, 0 replies; 8+ messages in thread From: Jonathan Cameron @ 2013-12-03 20:37 UTC (permalink / raw) To: Srinivas Pandruvada; +Cc: linux-iio, Lars-Peter Clausen, Peter Meerwald On 11/09/13 12:11, Jonathan Cameron wrote: > On 11/06/13 00:11, Srinivas Pandruvada wrote: >> Added usage id processing for Inclinometer 3D. This uses IIO >> interfaces for triggered buffer to present data to user >> mode.This uses HID sensor framework for registering callback >> events from the sensor hub. >> >> Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> > The driver is fine. One remaining question is where this driver (and similar > ones should be located). What groups make sense? > > Inclinometers are mostly (if not all?) accelerometer based. Should we put them > in the accelerometer group or are our current groups no ideal? > > I have applied this as presented as I suspect we need to have a more general > reorganization. > > What do others think? > > Anyhow, applied to the togreg branch of iio.git After a few 'interesting' issues due to the first patch in this series going in as a fix, I have reapplied this patch to the togreg branch (pushed out for now as testing) of iio.git. The prerequisits are now in place - note to anyone really observant - this is why the iio.git togreg branch just got rebased. > > Thanks, > > Jonathan >> --- >> drivers/iio/Kconfig | 1 + >> drivers/iio/Makefile | 1 + >> drivers/iio/orientation/Kconfig | 19 ++ >> drivers/iio/orientation/Makefile | 6 + >> drivers/iio/orientation/hid-sensor-incl-3d.c | 428 +++++++++++++++++++++++++++ >> include/linux/hid-sensor-ids.h | 4 + >> 6 files changed, 459 insertions(+) >> create mode 100644 drivers/iio/orientation/Kconfig >> create mode 100644 drivers/iio/orientation/Makefile >> create mode 100644 drivers/iio/orientation/hid-sensor-incl-3d.c >> >> diff --git a/drivers/iio/Kconfig b/drivers/iio/Kconfig >> index 90cf0cd..73ff5bb 100644 >> --- a/drivers/iio/Kconfig >> +++ b/drivers/iio/Kconfig >> @@ -68,6 +68,7 @@ source "drivers/iio/gyro/Kconfig" >> source "drivers/iio/imu/Kconfig" >> source "drivers/iio/light/Kconfig" >> source "drivers/iio/magnetometer/Kconfig" >> +source "drivers/iio/orientation/Kconfig" >> if IIO_TRIGGER >> source "drivers/iio/trigger/Kconfig" >> endif #IIO_TRIGGER >> diff --git a/drivers/iio/Makefile b/drivers/iio/Makefile >> index bcf7e9e..c682e1b 100644 >> --- a/drivers/iio/Makefile >> +++ b/drivers/iio/Makefile >> @@ -21,6 +21,7 @@ obj-y += frequency/ >> obj-y += imu/ >> obj-y += light/ >> obj-y += magnetometer/ >> +obj-y += orientation/ >> obj-y += pressure/ >> obj-y += temperature/ >> obj-y += trigger/ >> diff --git a/drivers/iio/orientation/Kconfig b/drivers/iio/orientation/Kconfig >> new file mode 100644 >> index 0000000..58c62c8 >> --- /dev/null >> +++ b/drivers/iio/orientation/Kconfig >> @@ -0,0 +1,19 @@ >> +# >> +# Inclinometer sensors >> +# >> +# When adding new entries keep the list in alphabetical order >> + >> +menu "Inclinometer sensors" >> + >> +config HID_SENSOR_INCLINOMETER_3D >> + depends on HID_SENSOR_HUB >> + select IIO_BUFFER >> + select IIO_TRIGGERED_BUFFER >> + select HID_SENSOR_IIO_COMMON >> + select HID_SENSOR_IIO_TRIGGER >> + tristate "HID Inclinometer 3D" >> + help >> + Say yes here to build support for the HID SENSOR >> + Inclinometer 3D. >> + >> +endmenu >> diff --git a/drivers/iio/orientation/Makefile b/drivers/iio/orientation/Makefile >> new file mode 100644 >> index 0000000..2c97572 >> --- /dev/null >> +++ b/drivers/iio/orientation/Makefile >> @@ -0,0 +1,6 @@ >> +# >> +# Makefile for industrial I/O Inclinometer sensor drivers >> +# >> + >> +# When adding new entries keep the list in alphabetical order >> +obj-$(CONFIG_HID_SENSOR_INCLINOMETER_3D) += hid-sensor-incl-3d.o >> diff --git a/drivers/iio/orientation/hid-sensor-incl-3d.c b/drivers/iio/orientation/hid-sensor-incl-3d.c >> new file mode 100644 >> index 0000000..070feab >> --- /dev/null >> +++ b/drivers/iio/orientation/hid-sensor-incl-3d.c >> @@ -0,0 +1,428 @@ >> +/* >> + * HID Sensors Driver >> + * Copyright (c) 2013, Intel Corporation. >> + * >> + * This program is free software; you can redistribute it and/or modify it >> + * under the terms and conditions of the GNU General Public License, >> + * version 2, as published by the Free Software Foundation. >> + * >> + * This program is distributed in the hope it will be useful, but WITHOUT >> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or >> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for >> + * more details. >> + * >> + * You should have received a copy of the GNU General Public License along with >> + * this program; if not, write to the Free Software Foundation, Inc. >> + * >> + */ >> + >> +#include <linux/device.h> >> +#include <linux/platform_device.h> >> +#include <linux/module.h> >> +#include <linux/interrupt.h> >> +#include <linux/irq.h> >> +#include <linux/slab.h> >> +#include <linux/hid-sensor-hub.h> >> +#include <linux/iio/iio.h> >> +#include <linux/iio/sysfs.h> >> +#include <linux/iio/buffer.h> >> +#include <linux/iio/trigger_consumer.h> >> +#include <linux/iio/triggered_buffer.h> >> +#include "../common/hid-sensors/hid-sensor-trigger.h" >> + >> +enum incl_3d_channel { >> + CHANNEL_SCAN_INDEX_X, >> + CHANNEL_SCAN_INDEX_Y, >> + CHANNEL_SCAN_INDEX_Z, >> + INCLI_3D_CHANNEL_MAX, >> +}; >> + >> +struct incl_3d_state { >> + struct hid_sensor_hub_callbacks callbacks; >> + struct hid_sensor_common common_attributes; >> + struct hid_sensor_hub_attribute_info incl[INCLI_3D_CHANNEL_MAX]; >> + u32 incl_val[INCLI_3D_CHANNEL_MAX]; >> +}; >> + >> +static const u32 incl_3d_addresses[INCLI_3D_CHANNEL_MAX] = { >> + HID_USAGE_SENSOR_ORIENT_TILT_X, >> + HID_USAGE_SENSOR_ORIENT_TILT_Y, >> + HID_USAGE_SENSOR_ORIENT_TILT_Z >> +}; >> + >> +/* Channel definitions */ >> +static const struct iio_chan_spec incl_3d_channels[] = { >> + { >> + .type = IIO_INCLI, >> + .modified = 1, >> + .channel2 = IIO_MOD_X, >> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | >> + BIT(IIO_CHAN_INFO_SCALE) | >> + BIT(IIO_CHAN_INFO_SAMP_FREQ) | >> + BIT(IIO_CHAN_INFO_HYSTERESIS), >> + .scan_index = CHANNEL_SCAN_INDEX_X, >> + }, { >> + .type = IIO_INCLI, >> + .modified = 1, >> + .channel2 = IIO_MOD_Y, >> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | >> + BIT(IIO_CHAN_INFO_SCALE) | >> + BIT(IIO_CHAN_INFO_SAMP_FREQ) | >> + BIT(IIO_CHAN_INFO_HYSTERESIS), >> + .scan_index = CHANNEL_SCAN_INDEX_Y, >> + }, { >> + .type = IIO_INCLI, >> + .modified = 1, >> + .channel2 = IIO_MOD_Z, >> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | >> + BIT(IIO_CHAN_INFO_SCALE) | >> + BIT(IIO_CHAN_INFO_SAMP_FREQ) | >> + BIT(IIO_CHAN_INFO_HYSTERESIS), >> + .scan_index = CHANNEL_SCAN_INDEX_Z, >> + } >> +}; >> + >> +/* Adjust channel real bits based on report descriptor */ >> +static void incl_3d_adjust_channel_bit_mask(struct iio_chan_spec *chan, >> + int size) >> +{ >> + chan->scan_type.sign = 's'; >> + /* Real storage bits will change based on the report desc. */ >> + chan->scan_type.realbits = size * 8; >> + /* Maximum size of a sample to capture is u32 */ >> + chan->scan_type.storagebits = sizeof(u32) * 8; >> +} >> + >> +/* Channel read_raw handler */ >> +static int incl_3d_read_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *chan, >> + int *val, int *val2, >> + long mask) >> +{ >> + struct incl_3d_state *incl_state = iio_priv(indio_dev); >> + int report_id = -1; >> + u32 address; >> + int ret_type; >> + >> + *val = 0; >> + *val2 = 0; >> + switch (mask) { >> + case IIO_CHAN_INFO_RAW: >> + report_id = >> + incl_state->incl[chan->scan_index].report_id; >> + address = incl_3d_addresses[chan->scan_index]; >> + if (report_id >= 0) >> + *val = sensor_hub_input_attr_get_raw_value( >> + incl_state->common_attributes.hsdev, >> + HID_USAGE_SENSOR_INCLINOMETER_3D, address, >> + report_id); >> + else { >> + return -EINVAL; >> + } >> + ret_type = IIO_VAL_INT; >> + break; >> + case IIO_CHAN_INFO_SCALE: >> + *val = incl_state->incl[CHANNEL_SCAN_INDEX_X].units; >> + ret_type = IIO_VAL_INT; >> + break; >> + case IIO_CHAN_INFO_OFFSET: >> + *val = hid_sensor_convert_exponent( >> + incl_state->incl[CHANNEL_SCAN_INDEX_X].unit_expo); >> + ret_type = IIO_VAL_INT; >> + break; >> + case IIO_CHAN_INFO_SAMP_FREQ: >> + ret_type = hid_sensor_read_samp_freq_value( >> + &incl_state->common_attributes, val, val2); >> + break; >> + case IIO_CHAN_INFO_HYSTERESIS: >> + ret_type = hid_sensor_read_raw_hyst_value( >> + &incl_state->common_attributes, val, val2); >> + break; >> + default: >> + ret_type = -EINVAL; >> + break; >> + } >> + >> + return ret_type; >> +} >> + >> +/* Channel write_raw handler */ >> +static int incl_3d_write_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *chan, >> + int val, >> + int val2, >> + long mask) >> +{ >> + struct incl_3d_state *incl_state = iio_priv(indio_dev); >> + int ret; >> + >> + switch (mask) { >> + case IIO_CHAN_INFO_SAMP_FREQ: >> + ret = hid_sensor_write_samp_freq_value( >> + &incl_state->common_attributes, val, val2); >> + break; >> + case IIO_CHAN_INFO_HYSTERESIS: >> + ret = hid_sensor_write_raw_hyst_value( >> + &incl_state->common_attributes, val, val2); >> + break; >> + default: >> + ret = -EINVAL; >> + } >> + >> + return ret; >> +} >> + >> +static const struct iio_info incl_3d_info = { >> + .driver_module = THIS_MODULE, >> + .read_raw = &incl_3d_read_raw, >> + .write_raw = &incl_3d_write_raw, >> +}; >> + >> +/* Function to push data to buffer */ >> +static void hid_sensor_push_data(struct iio_dev *indio_dev, u8 *data, int len) >> +{ >> + dev_dbg(&indio_dev->dev, "hid_sensor_push_data\n"); >> + iio_push_to_buffers(indio_dev, (u8 *)data); >> +} >> + >> +/* Callback handler to send event after all samples are received and captured */ >> +static int incl_3d_proc_event(struct hid_sensor_hub_device *hsdev, >> + unsigned usage_id, >> + void *priv) >> +{ >> + struct iio_dev *indio_dev = platform_get_drvdata(priv); >> + struct incl_3d_state *incl_state = iio_priv(indio_dev); >> + >> + dev_dbg(&indio_dev->dev, "incl_3d_proc_event [%d]\n", >> + incl_state->common_attributes.data_ready); >> + if (incl_state->common_attributes.data_ready) >> + hid_sensor_push_data(indio_dev, >> + (u8 *)incl_state->incl_val, >> + sizeof(incl_state->incl_val)); >> + >> + return 0; >> +} >> + >> +/* Capture samples in local storage */ >> +static int incl_3d_capture_sample(struct hid_sensor_hub_device *hsdev, >> + unsigned usage_id, >> + size_t raw_len, char *raw_data, >> + void *priv) >> +{ >> + struct iio_dev *indio_dev = platform_get_drvdata(priv); >> + struct incl_3d_state *incl_state = iio_priv(indio_dev); >> + int ret = 0; >> + >> + switch (usage_id) { >> + case HID_USAGE_SENSOR_ORIENT_TILT_X: >> + incl_state->incl_val[CHANNEL_SCAN_INDEX_X] = *(u32 *)raw_data; >> + break; >> + case HID_USAGE_SENSOR_ORIENT_TILT_Y: >> + incl_state->incl_val[CHANNEL_SCAN_INDEX_Y] = *(u32 *)raw_data; >> + break; >> + case HID_USAGE_SENSOR_ORIENT_TILT_Z: >> + incl_state->incl_val[CHANNEL_SCAN_INDEX_Z] = *(u32 *)raw_data; >> + break; >> + default: >> + ret = -EINVAL; >> + break; >> + } >> + >> + return ret; >> +} >> + >> +/* Parse report which is specific to an usage id*/ >> +static int incl_3d_parse_report(struct platform_device *pdev, >> + struct hid_sensor_hub_device *hsdev, >> + struct iio_chan_spec *channels, >> + unsigned usage_id, >> + struct incl_3d_state *st) >> +{ >> + int ret; >> + >> + ret = sensor_hub_input_get_attribute_info(hsdev, >> + HID_INPUT_REPORT, >> + usage_id, >> + HID_USAGE_SENSOR_ORIENT_TILT_X, >> + &st->incl[CHANNEL_SCAN_INDEX_X]); >> + if (ret) >> + return ret; >> + incl_3d_adjust_channel_bit_mask(&channels[CHANNEL_SCAN_INDEX_X], >> + st->incl[CHANNEL_SCAN_INDEX_X].size); >> + >> + ret = sensor_hub_input_get_attribute_info(hsdev, >> + HID_INPUT_REPORT, >> + usage_id, >> + HID_USAGE_SENSOR_ORIENT_TILT_Y, >> + &st->incl[CHANNEL_SCAN_INDEX_Y]); >> + if (ret) >> + return ret; >> + incl_3d_adjust_channel_bit_mask(&channels[CHANNEL_SCAN_INDEX_Y], >> + st->incl[CHANNEL_SCAN_INDEX_Y].size); >> + >> + ret = sensor_hub_input_get_attribute_info(hsdev, >> + HID_INPUT_REPORT, >> + usage_id, >> + HID_USAGE_SENSOR_ORIENT_TILT_Z, >> + &st->incl[CHANNEL_SCAN_INDEX_Z]); >> + if (ret) >> + return ret; >> + incl_3d_adjust_channel_bit_mask(&channels[CHANNEL_SCAN_INDEX_Z], >> + st->incl[CHANNEL_SCAN_INDEX_Z].size); >> + >> + dev_dbg(&pdev->dev, "incl_3d %x:%x, %x:%x, %x:%x\n", >> + st->incl[0].index, >> + st->incl[0].report_id, >> + st->incl[1].index, st->incl[1].report_id, >> + st->incl[2].index, st->incl[2].report_id); >> + >> + /* Set Sensitivity field ids, when there is no individual modifier */ >> + if (st->common_attributes.sensitivity.index < 0) { >> + sensor_hub_input_get_attribute_info(hsdev, >> + HID_FEATURE_REPORT, usage_id, >> + HID_USAGE_SENSOR_DATA_MOD_CHANGE_SENSITIVITY_ABS | >> + HID_USAGE_SENSOR_DATA_ORIENTATION, >> + &st->common_attributes.sensitivity); >> + dev_dbg(&pdev->dev, "Sensitivity index:report %d:%d\n", >> + st->common_attributes.sensitivity.index, >> + st->common_attributes.sensitivity.report_id); >> + } >> + return ret; >> +} >> + >> +/* Function to initialize the processing for usage id */ >> +static int hid_incl_3d_probe(struct platform_device *pdev) >> +{ >> + int ret; >> + static char *name = "incli_3d"; >> + struct iio_dev *indio_dev; >> + struct incl_3d_state *incl_state; >> + struct hid_sensor_hub_device *hsdev = pdev->dev.platform_data; >> + struct iio_chan_spec *channels; >> + >> + indio_dev = devm_iio_device_alloc(&pdev->dev, >> + sizeof(struct incl_3d_state)); >> + if (indio_dev == NULL) >> + return -ENOMEM; >> + >> + platform_set_drvdata(pdev, indio_dev); >> + >> + incl_state = iio_priv(indio_dev); >> + incl_state->common_attributes.hsdev = hsdev; >> + incl_state->common_attributes.pdev = pdev; >> + >> + ret = hid_sensor_parse_common_attributes(hsdev, >> + HID_USAGE_SENSOR_INCLINOMETER_3D, >> + &incl_state->common_attributes); >> + if (ret) { >> + dev_err(&pdev->dev, "failed to setup common attributes\n"); >> + return ret; >> + } >> + >> + channels = kmemdup(incl_3d_channels, sizeof(incl_3d_channels), >> + GFP_KERNEL); >> + if (!channels) { >> + dev_err(&pdev->dev, "failed to duplicate channels\n"); >> + return -ENOMEM; >> + } >> + >> + ret = incl_3d_parse_report(pdev, hsdev, channels, >> + HID_USAGE_SENSOR_INCLINOMETER_3D, incl_state); >> + if (ret) { >> + dev_err(&pdev->dev, "failed to setup attributes\n"); >> + goto error_free_dev_mem; >> + } >> + >> + indio_dev->channels = channels; >> + indio_dev->num_channels = ARRAY_SIZE(incl_3d_channels); >> + indio_dev->dev.parent = &pdev->dev; >> + indio_dev->info = &incl_3d_info; >> + indio_dev->name = name; >> + indio_dev->modes = INDIO_DIRECT_MODE; >> + >> + ret = iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time, >> + NULL, NULL); >> + if (ret) { >> + dev_err(&pdev->dev, "failed to initialize trigger buffer\n"); >> + goto error_free_dev_mem; >> + } >> + incl_state->common_attributes.data_ready = false; >> + ret = hid_sensor_setup_trigger(indio_dev, name, >> + &incl_state->common_attributes); >> + if (ret) { >> + dev_err(&pdev->dev, "trigger setup failed\n"); >> + goto error_unreg_buffer_funcs; >> + } >> + >> + ret = iio_device_register(indio_dev); >> + if (ret) { >> + dev_err(&pdev->dev, "device register failed\n"); >> + goto error_remove_trigger; >> + } >> + >> + incl_state->callbacks.send_event = incl_3d_proc_event; >> + incl_state->callbacks.capture_sample = incl_3d_capture_sample; >> + incl_state->callbacks.pdev = pdev; >> + ret = sensor_hub_register_callback(hsdev, >> + HID_USAGE_SENSOR_INCLINOMETER_3D, >> + &incl_state->callbacks); >> + if (ret) { >> + dev_err(&pdev->dev, "callback reg failed\n"); >> + goto error_iio_unreg; >> + } >> + >> + return 0; >> + >> +error_iio_unreg: >> + iio_device_unregister(indio_dev); >> +error_remove_trigger: >> + hid_sensor_remove_trigger(&incl_state->common_attributes); >> +error_unreg_buffer_funcs: >> + iio_triggered_buffer_cleanup(indio_dev); >> +error_free_dev_mem: >> + kfree(indio_dev->channels); >> + return ret; >> +} >> + >> +/* Function to deinitialize the processing for usage id */ >> +static int hid_incl_3d_remove(struct platform_device *pdev) >> +{ >> + struct hid_sensor_hub_device *hsdev = pdev->dev.platform_data; >> + struct iio_dev *indio_dev = platform_get_drvdata(pdev); >> + struct incl_3d_state *incl_state = iio_priv(indio_dev); >> + >> + sensor_hub_remove_callback(hsdev, HID_USAGE_SENSOR_INCLINOMETER_3D); >> + iio_device_unregister(indio_dev); >> + hid_sensor_remove_trigger(&incl_state->common_attributes); >> + iio_triggered_buffer_cleanup(indio_dev); >> + kfree(indio_dev->channels); >> + >> + return 0; >> +} >> + >> +static struct platform_device_id hid_incl_3d_ids[] = { >> + { >> + /* Format: HID-SENSOR-usage_id_in_hex_lowercase */ >> + .name = "HID-SENSOR-200086", >> + }, >> + { /* sentinel */ } >> +}; >> +MODULE_DEVICE_TABLE(platform, hid_incl_3d_ids); >> + >> +static struct platform_driver hid_incl_3d_platform_driver = { >> + .id_table = hid_incl_3d_ids, >> + .driver = { >> + .name = KBUILD_MODNAME, >> + .owner = THIS_MODULE, >> + }, >> + .probe = hid_incl_3d_probe, >> + .remove = hid_incl_3d_remove, >> +}; >> +module_platform_driver(hid_incl_3d_platform_driver); >> + >> +MODULE_DESCRIPTION("HID Sensor Inclinometer 3D"); >> +MODULE_AUTHOR("Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>"); >> +MODULE_LICENSE("GPL"); >> diff --git a/include/linux/hid-sensor-ids.h b/include/linux/hid-sensor-ids.h >> index e6e5fb9..0232055 100644 >> --- a/include/linux/hid-sensor-ids.h >> +++ b/include/linux/hid-sensor-ids.h >> @@ -58,10 +58,14 @@ >> #define HID_USAGE_SENSOR_ORIENT_DISTANCE_Y 0x20047B >> #define HID_USAGE_SENSOR_ORIENT_DISTANCE_Z 0x20047C >> #define HID_USAGE_SENSOR_ORIENT_DISTANCE_OUT_OF_RANGE 0x20047D >> + >> +/* ORIENTATION: Inclinometer 3D: (200086) */ >> +#define HID_USAGE_SENSOR_INCLINOMETER_3D 0x200086 >> #define HID_USAGE_SENSOR_ORIENT_TILT 0x20047E >> #define HID_USAGE_SENSOR_ORIENT_TILT_X 0x20047F >> #define HID_USAGE_SENSOR_ORIENT_TILT_Y 0x200480 >> #define HID_USAGE_SENSOR_ORIENT_TILT_Z 0x200481 >> + >> #define HID_USAGE_SENSOR_ORIENT_ROTATION_MATRIX 0x200482 >> #define HID_USAGE_SENSOR_ORIENT_QUATERNION 0x200483 >> #define HID_USAGE_SENSOR_ORIENT_MAGN_FLUX 0x200484 >> > -- > To unsubscribe from this list: send the line "unsubscribe linux-iio" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2013-12-03 20:37 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <a>
2013-11-06 0:11 ` [PATCH v4 1/5] iio: hid-sensors: accelerometer: Add sensitivity Srinivas Pandruvada
2013-11-06 0:11 ` [PATCH v4 2/5] iio: hid-sensors: gyro : " Srinivas Pandruvada
2013-11-06 0:11 ` [PATCH v4 3/5] iio: hid-sensors: light/als " Srinivas Pandruvada
2013-11-06 0:11 ` [PATCH v4 4/5] iio: hid-sensors: magnetometer " Srinivas Pandruvada
2013-11-09 11:56 ` Jonathan Cameron
2013-11-06 0:11 ` [PATCH v4 5/5] iio: hid-sensors: Added Inclinometer 3D Srinivas Pandruvada
2013-11-09 12:11 ` Jonathan Cameron
2013-12-03 20:37 ` Jonathan Cameron
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).