* [PULL] IIO new driver, features and cleanups for 3.18 - set 2
@ 2014-09-16 20:15 Jonathan Cameron
2014-09-19 22:27 ` Greg KH
0 siblings, 1 reply; 2+ messages in thread
From: Jonathan Cameron @ 2014-09-16 20:15 UTC (permalink / raw)
To: Greg KH; +Cc: linux-iio@vger.kernel.org
The following changes since commit 29a9e89548408028498bb63bcaabe2806232e26a:
staging: unisys: fix indentation of uisutil_copy_fragsinfo_from_skb() (2014-08-25 17:16:06 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git tags/iio-for-3.18b
for you to fetch changes up to 2017cff24cc08b145bff7256dd6b0ef99e7e8a01:
iio:bma180: Add BMA250 chip support (2014-09-14 20:52:25 +0100)
----------------------------------------------------------------
Second round of new IIO drivers, features and cleanups for the 3.18 cycle.
New drivers and part support
* Bosch bmg160 Gyroscope driver
* Dyna-Image al3320a ambient light sensor driver
* Bosh bmi055 gyroscope part driver (accelerometer part supported by bmc150)
* isl29018 - add support for isl29023 and isl29035
* kxcjk-1013 - add support for kxcj9-1008 and kxtj2-1009
* bmc150 - additional part support (BMI055 accelerometer part, BMA255,
BMA222E, BMA250E and BMA280). Different resolutions but otherwise similar
parts.
* bma180 - add BMA250 (note different from the BMA250E support above despite
the naming). A lot of driver reworking lead up to this - described below.
New features
* kxcjk1013 - add threshold event support.
* rockchip - document DT bindings.
* isl29018 - ACPI support
* bma180 - enable use without IRQ
Cleanups
* Tree wide - drop owner field assignment if using the module_platform_driver
helper as that assigns it anyway.
* kxcjk1013 - drop a redundant assignment of the current range and fix a
a defined but not used warning.
* inv_mpu6050 - Remove an unnecessary cast form a void pointer.
* rockchip - drop and unused variable.
* at91_adc - make a local function static.
* st-sensors-core - correctly handle an error in setting in
st_sensors_set_drdy_int_pin
* isl29018 - typo fix
* bmc150 - fix incorrect scale value for 16G range (Driver new this cycle)
* bmc150 - fix issues when CONFIG_PM_RUNTIME not set (Driver new this cycle)
* ad7606 - line length tidy up.
* bmg160 - set power state only if PM_RUNTIME is defined.
* ak8975 - fix some unnecessary casting between char * and const char *
* bma180 - prefix remaining bits and bobs with bma180_ and ensure consistent.
- use a bool instead of an int for state (as its either on or off).
- expose the temperature channel
- statically allocate buffers to avoid need for update_scan_mode
callback.
- refactor to allow futher chip variants including support for part
specific config and disable code + different resolutions.
----------------------------------------------------------------
Daniel Baluta (5):
io: accel: kxcjk1013: Remove redundant assignment
iio: accel: kxcjk-1013: add support for kxcj9-1008
iio: Add Dyna-Image AL3320A ambient light sensor driver
iio: accel: kxcjk-1013: add support for kxtj2-1009
iio: accel: kxcjk-1013: Fix defined but unused warning
Heiko Stübner (2):
iio: adc: rockchip_saradc: remove unused variable in probe
dt-bindings: document Rockchip saradc
Irina Tirdea (3):
iio: gyro: bmg160: only set power state if PM_RUNTIME is defined
iio: magn: ak8975: fix unnecessary casting between char* and const char*
iio: gyro: bmi055 gyro sensor driver
Jingoo Han (1):
iio: imu: inv_mpu6050: Remove casting the return value which is a void pointer
Josh Wu (1):
iio: adc: at91: make the function handle_adc_eoc_trigger() static
Laurentiu Palcu (6):
staging: iio: light: isl29018: fix typo
staging: iio: light: isl29018: add support for isl29023 and isl29035
iio: accel: BMC150: fix scale value for 16G
iio: accel: BMC150: fix issues when CONFIG_PM_RUNTIME is not set
staging: iio: light: isl29018: add ACPI support
iio: accel: BMC150: add support for other Bosch chips
Lee Jones (1):
iio: sensors-core: st: Check st_sensors_set_drdy_int_pin()'s return value
Peter Meerwald (11):
iio:bma180: Enable use of device without IRQ
iio:bma180: Prefix remaining tables and functions with bma18_
iio:bma180: Rename BMA_180 to BMA180_
iio:bma180: Use bool instead of int for state
iio:bma180: Expose temperature channel
iio:bma180: Drop _update_scan_mode()
iio:bma180: Introduce part_info to differentiate further chip variants
iio:bma180: Introduce part-specific _config() and disable() code
iio:bma180: Prepare for accelerometer channels with different resolutions
iio:bma180: Implement _available sysfs attribute dynamically
iio:bma180: Add BMA250 chip support
Sanjeev Sharma (1):
iio: remove .owner field for driver using module_platform_driver
Srinivas Pandruvada (3):
iio:gyro:bmg160 Gyro Sensor driver
iio:gyro:bmg160 documentation
iio: accel: kxcjk-1013: Support thresholds
Sören Brinkmann (1):
staging: ad7606_core: Fix checkpatch warning
.../ABI/testing/sysfs-bus-iio-gyro-bmg160 | 7 +
.../bindings/iio/adc/rockchip-saradc.txt | 24 +
drivers/iio/accel/Kconfig | 13 +-
drivers/iio/accel/bma180.c | 476 +++++---
drivers/iio/accel/bmc150-accel.c | 241 +++-
drivers/iio/accel/hid-sensor-accel-3d.c | 1 -
drivers/iio/accel/kxcjk-1013.c | 611 ++++++++--
drivers/iio/adc/at91_adc.c | 2 +-
drivers/iio/adc/exynos_adc.c | 1 -
drivers/iio/adc/lp8788_adc.c | 1 -
drivers/iio/adc/rockchip_saradc.c | 1 -
drivers/iio/adc/ti_am335x_adc.c | 1 -
drivers/iio/adc/twl4030-madc.c | 1 -
drivers/iio/adc/twl6030-gpadc.c | 1 -
drivers/iio/adc/vf610_adc.c | 1 -
drivers/iio/adc/viperboard_adc.c | 1 -
drivers/iio/common/st_sensors/st_sensors_core.c | 5 +-
drivers/iio/gyro/Kconfig | 11 +
drivers/iio/gyro/Makefile | 1 +
drivers/iio/gyro/bmg160.c | 1228 ++++++++++++++++++++
drivers/iio/gyro/hid-sensor-gyro-3d.c | 1 -
drivers/iio/humidity/dht11.c | 1 -
drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 3 +-
drivers/iio/light/Kconfig | 10 +
drivers/iio/light/Makefile | 1 +
drivers/iio/light/al3320a.c | 232 ++++
drivers/iio/light/hid-sensor-als.c | 1 -
drivers/iio/light/hid-sensor-prox.c | 1 -
drivers/iio/light/lm3533-als.c | 1 -
drivers/iio/magnetometer/ak8975.c | 10 +-
drivers/iio/magnetometer/hid-sensor-magn-3d.c | 1 -
drivers/iio/orientation/hid-sensor-incl-3d.c | 1 -
drivers/iio/orientation/hid-sensor-rotation.c | 1 -
drivers/iio/pressure/hid-sensor-press.c | 1 -
drivers/iio/trigger/iio-trig-interrupt.c | 1 -
drivers/staging/iio/adc/ad7606_core.c | 2 +-
drivers/staging/iio/light/isl29018.c | 205 +++-
37 files changed, 2763 insertions(+), 338 deletions(-)
create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-gyro-bmg160
create mode 100644 Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt
create mode 100644 drivers/iio/gyro/bmg160.c
create mode 100644 drivers/iio/light/al3320a.c
The following changes since commit 29a9e89548408028498bb63bcaabe2806232e26a:
staging: unisys: fix indentation of uisutil_copy_fragsinfo_from_skb() (2014-08-25 17:16:06 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git tags/iio-for-3.18b
for you to fetch changes up to 2017cff24cc08b145bff7256dd6b0ef99e7e8a01:
iio:bma180: Add BMA250 chip support (2014-09-14 20:52:25 +0100)
----------------------------------------------------------------
Second round of new IIO drivers, features and cleanups for the 3.18 cycle.
New drivers and part support
* Bosch bmg160 Gyroscope driver
* Dyna-Image al3320a ambient light sensor driver
* Bosh bmi055 gyroscope part driver (accelerometer part supported by bmc150)
* isl29018 - add support for isl29023 and isl29035
* kxcjk-1013 - add support for kxcj9-1008 and kxtj2-1009
* bmc150 - additional part support (BMI055 accelerometer part, BMA255,
BMA222E, BMA250E and BMA280). Different resolutions but otherwise similar
parts.
* bma180 - add BMA250 (note different from the BMA250E support above despite
the naming). A lot of driver reworking lead up to this - described below.
New features
* kxcjk1013 - add threshold event support.
* rockchip - document DT bindings.
* isl29018 - ACPI support
* bma180 - enable use without IRQ
Cleanups
* Tree wide - drop owner field assignment if using the module_platform_driver
helper as that assigns it anyway.
* kxcjk1013 - drop a redundant assignment of the current range and fix a
a defined but not used warning.
* inv_mpu6050 - Remove an unnecessary cast form a void pointer.
* rockchip - drop and unused variable.
* at91_adc - make a local function static.
* st-sensors-core - correctly handle an error in setting in
st_sensors_set_drdy_int_pin
* isl29018 - typo fix
* bmc150 - fix incorrect scale value for 16G range (Driver new this cycle)
* bmc150 - fix issues when CONFIG_PM_RUNTIME not set (Driver new this cycle)
* ad7606 - line length tidy up.
* bmg160 - set power state only if PM_RUNTIME is defined.
* ak8975 - fix some unnecessary casting between char * and const char *
* bma180 - prefix remaining bits and bobs with bma180_ and ensure consistent.
- use a bool instead of an int for state (as its either on or off).
- expose the temperature channel
- statically allocate buffers to avoid need for update_scan_mode
callback.
- refactor to allow futher chip variants including support for part
specific config and disable code + different resolutions.
----------------------------------------------------------------
Daniel Baluta (5):
io: accel: kxcjk1013: Remove redundant assignment
iio: accel: kxcjk-1013: add support for kxcj9-1008
iio: Add Dyna-Image AL3320A ambient light sensor driver
iio: accel: kxcjk-1013: add support for kxtj2-1009
iio: accel: kxcjk-1013: Fix defined but unused warning
Heiko Stübner (2):
iio: adc: rockchip_saradc: remove unused variable in probe
dt-bindings: document Rockchip saradc
Irina Tirdea (3):
iio: gyro: bmg160: only set power state if PM_RUNTIME is defined
iio: magn: ak8975: fix unnecessary casting between char* and const char*
iio: gyro: bmi055 gyro sensor driver
Jingoo Han (1):
iio: imu: inv_mpu6050: Remove casting the return value which is a void pointer
Josh Wu (1):
iio: adc: at91: make the function handle_adc_eoc_trigger() static
Laurentiu Palcu (6):
staging: iio: light: isl29018: fix typo
staging: iio: light: isl29018: add support for isl29023 and isl29035
iio: accel: BMC150: fix scale value for 16G
iio: accel: BMC150: fix issues when CONFIG_PM_RUNTIME is not set
staging: iio: light: isl29018: add ACPI support
iio: accel: BMC150: add support for other Bosch chips
Lee Jones (1):
iio: sensors-core: st: Check st_sensors_set_drdy_int_pin()'s return value
Peter Meerwald (11):
iio:bma180: Enable use of device without IRQ
iio:bma180: Prefix remaining tables and functions with bma18_
iio:bma180: Rename BMA_180 to BMA180_
iio:bma180: Use bool instead of int for state
iio:bma180: Expose temperature channel
iio:bma180: Drop _update_scan_mode()
iio:bma180: Introduce part_info to differentiate further chip variants
iio:bma180: Introduce part-specific _config() and disable() code
iio:bma180: Prepare for accelerometer channels with different resolutions
iio:bma180: Implement _available sysfs attribute dynamically
iio:bma180: Add BMA250 chip support
Sanjeev Sharma (1):
iio: remove .owner field for driver using module_platform_driver
Srinivas Pandruvada (3):
iio:gyro:bmg160 Gyro Sensor driver
iio:gyro:bmg160 documentation
iio: accel: kxcjk-1013: Support thresholds
Sören Brinkmann (1):
staging: ad7606_core: Fix checkpatch warning
.../ABI/testing/sysfs-bus-iio-gyro-bmg160 | 7 +
.../bindings/iio/adc/rockchip-saradc.txt | 24 +
drivers/iio/accel/Kconfig | 13 +-
drivers/iio/accel/bma180.c | 476 +++++---
drivers/iio/accel/bmc150-accel.c | 241 +++-
drivers/iio/accel/hid-sensor-accel-3d.c | 1 -
drivers/iio/accel/kxcjk-1013.c | 611 ++++++++--
drivers/iio/adc/at91_adc.c | 2 +-
drivers/iio/adc/exynos_adc.c | 1 -
drivers/iio/adc/lp8788_adc.c | 1 -
drivers/iio/adc/rockchip_saradc.c | 1 -
drivers/iio/adc/ti_am335x_adc.c | 1 -
drivers/iio/adc/twl4030-madc.c | 1 -
drivers/iio/adc/twl6030-gpadc.c | 1 -
drivers/iio/adc/vf610_adc.c | 1 -
drivers/iio/adc/viperboard_adc.c | 1 -
drivers/iio/common/st_sensors/st_sensors_core.c | 5 +-
drivers/iio/gyro/Kconfig | 11 +
drivers/iio/gyro/Makefile | 1 +
drivers/iio/gyro/bmg160.c | 1228 ++++++++++++++++++++
drivers/iio/gyro/hid-sensor-gyro-3d.c | 1 -
drivers/iio/humidity/dht11.c | 1 -
drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 3 +-
drivers/iio/light/Kconfig | 10 +
drivers/iio/light/Makefile | 1 +
drivers/iio/light/al3320a.c | 232 ++++
drivers/iio/light/hid-sensor-als.c | 1 -
drivers/iio/light/hid-sensor-prox.c | 1 -
drivers/iio/light/lm3533-als.c | 1 -
drivers/iio/magnetometer/ak8975.c | 10 +-
drivers/iio/magnetometer/hid-sensor-magn-3d.c | 1 -
drivers/iio/orientation/hid-sensor-incl-3d.c | 1 -
drivers/iio/orientation/hid-sensor-rotation.c | 1 -
drivers/iio/pressure/hid-sensor-press.c | 1 -
drivers/iio/trigger/iio-trig-interrupt.c | 1 -
drivers/staging/iio/adc/ad7606_core.c | 2 +-
drivers/staging/iio/light/isl29018.c | 205 +++-
37 files changed, 2763 insertions(+), 338 deletions(-)
create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-gyro-bmg160
create mode 100644 Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt
create mode 100644 drivers/iio/gyro/bmg160.c
create mode 100644 drivers/iio/light/al3320a.c
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [PULL] IIO new driver, features and cleanups for 3.18 - set 2
2014-09-16 20:15 [PULL] IIO new driver, features and cleanups for 3.18 - set 2 Jonathan Cameron
@ 2014-09-19 22:27 ` Greg KH
0 siblings, 0 replies; 2+ messages in thread
From: Greg KH @ 2014-09-19 22:27 UTC (permalink / raw)
To: Jonathan Cameron; +Cc: linux-iio@vger.kernel.org
On Tue, Sep 16, 2014 at 09:15:20PM +0100, Jonathan Cameron wrote:
> The following changes since commit 29a9e89548408028498bb63bcaabe2806232e26a:
>
> staging: unisys: fix indentation of uisutil_copy_fragsinfo_from_skb() (2014-08-25 17:16:06 -0700)
>
> are available in the git repository at:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git tags/iio-for-3.18b
Pulled and pushed out, thanks.
greg k-h
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2014-09-19 22:27 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-09-16 20:15 [PULL] IIO new driver, features and cleanups for 3.18 - set 2 Jonathan Cameron
2014-09-19 22:27 ` Greg KH
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).