* [PATCH v3 1/2] devicetree: add documentation for MAX30102 oximeter @ 2017-02-04 10:22 Matt Ranostay 2017-02-04 10:22 ` [PATCH v3 2/2] iio: health: add MAX30102 oximeter driver support Matt Ranostay 2017-02-05 9:45 ` [PATCH v3 1/2] devicetree: add documentation for MAX30102 oximeter Jonathan Cameron 0 siblings, 2 replies; 4+ messages in thread From: Matt Ranostay @ 2017-02-04 10:22 UTC (permalink / raw) To: linux-iio; +Cc: Matt Ranostay Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Matt Ranostay <matt@ranostay.consulting> --- .../devicetree/bindings/iio/health/max30102.txt | 30 ++++++++++++++++++++++ 1 file changed, 30 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/health/max30102.txt Changes from v1: * none Changes from v2: * none diff --git a/Documentation/devicetree/bindings/iio/health/max30102.txt b/Documentation/devicetree/bindings/iio/health/max30102.txt new file mode 100644 index 000000000000..c695e7cbeefb --- /dev/null +++ b/Documentation/devicetree/bindings/iio/health/max30102.txt @@ -0,0 +1,30 @@ +Maxim MAX30102 heart rate and pulse oximeter sensor + +* https://datasheets.maximintegrated.com/en/ds/MAX30102.pdf + +Required properties: + - compatible: must be "maxim,max30102" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic + interrupt client node bindings. + +Optional properties: + - maxim,red-led-current-microamp: configuration for RED LED current + - maxim,ir-led-current-microamp: configuration for IR LED current + + Note that each step is approximately 200 microamps, ranging from 0 uA to + 50800 uA. + +Example: + +max30100@57 { + compatible = "maxim,max30102"; + reg = <0x57>; + maxim,red-led-current-microamp = <7000>; + maxim,ir-led-current-microamp = <7000>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; -- 2.10.2 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v3 2/2] iio: health: add MAX30102 oximeter driver support 2017-02-04 10:22 [PATCH v3 1/2] devicetree: add documentation for MAX30102 oximeter Matt Ranostay @ 2017-02-04 10:22 ` Matt Ranostay 2017-02-05 9:46 ` Jonathan Cameron 2017-02-05 9:45 ` [PATCH v3 1/2] devicetree: add documentation for MAX30102 oximeter Jonathan Cameron 1 sibling, 1 reply; 4+ messages in thread From: Matt Ranostay @ 2017-02-04 10:22 UTC (permalink / raw) To: linux-iio; +Cc: Matt Ranostay MAX30102 is an heart rate and pulse oximeter sensor that works using two LEDS of different wavelengths, and detecting the light reflected back. This patchset adds support for both IR and RED LED channels which can be processed in userspace to determine heart rate and blood oxygen levels. The MAX30102 part isn't completely register and functional compatible with the existing MAX30100 driver. Signed-off-by: Matt Ranostay <matt@ranostay.consulting> --- drivers/iio/health/Kconfig | 13 ++ drivers/iio/health/Makefile | 1 + drivers/iio/health/max30102.c | 485 ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 499 insertions(+) create mode 100644 drivers/iio/health/max30102.c Changes from v1: * add newlines to dev_err/dev_info statements * update documentation to 400hz samples, but actually 100hz to FIFO * fix storage bits to a power of 2, and the required buffer processing * fixed return code from max30102_read_measurement() Changes from v2: * correct shift value in MAX30102_REG_SPO2_CONFIG_ADC_MASK_SHIFT * changed iio_buffed_enabled() error from -EAGAIN to -EBUSY diff --git a/drivers/iio/health/Kconfig b/drivers/iio/health/Kconfig index c5f004a8e447..a2ecb4c94c2a 100644 --- a/drivers/iio/health/Kconfig +++ b/drivers/iio/health/Kconfig @@ -46,6 +46,19 @@ config MAX30100 To compile this driver as a module, choose M here: the module will be called max30100. +config MAX30102 + tristate "MAX30102 heart rate and pulse oximeter sensor" + depends on I2C + select REGMAP_I2C + select IIO_BUFFER + select IIO_KFIFO_BUF + help + Say Y here to build I2C interface support for the Maxim + MAX30102 heart rate, and pulse oximeter sensor. + + To compile this driver as a module, choose M here: the + module will be called max30102. + endmenu endmenu diff --git a/drivers/iio/health/Makefile b/drivers/iio/health/Makefile index 9955a2ae8df1..3558f9d64954 100644 --- a/drivers/iio/health/Makefile +++ b/drivers/iio/health/Makefile @@ -7,3 +7,4 @@ obj-$(CONFIG_AFE4403) += afe4403.o obj-$(CONFIG_AFE4404) += afe4404.o obj-$(CONFIG_MAX30100) += max30100.o +obj-$(CONFIG_MAX30102) += max30102.o diff --git a/drivers/iio/health/max30102.c b/drivers/iio/health/max30102.c new file mode 100644 index 000000000000..377518c15552 --- /dev/null +++ b/drivers/iio/health/max30102.c @@ -0,0 +1,485 @@ +/* + * max30102.c - Support for MAX30102 heart rate and pulse oximeter sensor + * + * Copyright (C) 2017 Matt Ranostay <matt@ranostay.consulting> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * TODO: proximity power saving feature + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/irq.h> +#include <linux/i2c.h> +#include <linux/mutex.h> +#include <linux/of.h> +#include <linux/regmap.h> +#include <linux/iio/iio.h> +#include <linux/iio/buffer.h> +#include <linux/iio/kfifo_buf.h> + +#define MAX30102_REGMAP_NAME "max30102_regmap" +#define MAX30102_DRV_NAME "max30102" + +#define MAX30102_REG_INT_STATUS 0x00 +#define MAX30102_REG_INT_STATUS_PWR_RDY BIT(0) +#define MAX30102_REG_INT_STATUS_PROX_INT BIT(4) +#define MAX30102_REG_INT_STATUS_ALC_OVF BIT(5) +#define MAX30102_REG_INT_STATUS_PPG_RDY BIT(6) +#define MAX30102_REG_INT_STATUS_FIFO_RDY BIT(7) + +#define MAX30102_REG_INT_ENABLE 0x02 +#define MAX30102_REG_INT_ENABLE_PROX_INT_EN BIT(4) +#define MAX30102_REG_INT_ENABLE_ALC_OVF_EN BIT(5) +#define MAX30102_REG_INT_ENABLE_PPG_EN BIT(6) +#define MAX30102_REG_INT_ENABLE_FIFO_EN BIT(7) +#define MAX30102_REG_INT_ENABLE_MASK 0xf0 +#define MAX30102_REG_INT_ENABLE_MASK_SHIFT 4 + +#define MAX30102_REG_FIFO_WR_PTR 0x04 +#define MAX30102_REG_FIFO_OVR_CTR 0x05 +#define MAX30102_REG_FIFO_RD_PTR 0x06 +#define MAX30102_REG_FIFO_DATA 0x07 +#define MAX30102_REG_FIFO_DATA_ENTRY_LEN 6 + +#define MAX30102_REG_FIFO_CONFIG 0x08 +#define MAX30102_REG_FIFO_CONFIG_AVG_4SAMPLES BIT(1) +#define MAX30102_REG_FIFO_CONFIG_AVG_SHIFT 5 +#define MAX30102_REG_FIFO_CONFIG_AFULL BIT(0) + +#define MAX30102_REG_MODE_CONFIG 0x09 +#define MAX30102_REG_MODE_CONFIG_MODE_SPO2_EN BIT(0) +#define MAX30102_REG_MODE_CONFIG_MODE_HR_EN BIT(1) +#define MAX30102_REG_MODE_CONFIG_MODE_MASK 0x03 +#define MAX30102_REG_MODE_CONFIG_PWR BIT(7) + +#define MAX30102_REG_SPO2_CONFIG 0x0a +#define MAX30102_REG_SPO2_CONFIG_PULSE_411_US 0x03 +#define MAX30102_REG_SPO2_CONFIG_SR_400HZ 0x03 +#define MAX30102_REG_SPO2_CONFIG_SR_MASK 0x07 +#define MAX30102_REG_SPO2_CONFIG_SR_MASK_SHIFT 2 +#define MAX30102_REG_SPO2_CONFIG_ADC_4096_STEPS BIT(0) +#define MAX30102_REG_SPO2_CONFIG_ADC_MASK_SHIFT 5 + +#define MAX30102_REG_RED_LED_CONFIG 0x0c +#define MAX30102_REG_IR_LED_CONFIG 0x0d + +#define MAX30102_REG_TEMP_CONFIG 0x21 +#define MAX30102_REG_TEMP_CONFIG_TEMP_EN BIT(0) + +#define MAX30102_REG_TEMP_INTEGER 0x1f +#define MAX30102_REG_TEMP_FRACTION 0x20 + +struct max30102_data { + struct i2c_client *client; + struct iio_dev *indio_dev; + struct mutex lock; + struct regmap *regmap; + + u8 buffer[8]; + __be32 processed_buffer[2]; /* 2 x 18-bit (padded to 32-bits) */ +}; + +static const struct regmap_config max30102_regmap_config = { + .name = MAX30102_REGMAP_NAME, + + .reg_bits = 8, + .val_bits = 8, +}; + +static const unsigned long max30102_scan_masks[] = {0x3, 0}; + +static const struct iio_chan_spec max30102_channels[] = { + { + .type = IIO_INTENSITY, + .channel2 = IIO_MOD_LIGHT_RED, + .modified = 1, + + .scan_index = 0, + .scan_type = { + .sign = 'u', + .shift = 8, + .realbits = 18, + .storagebits = 32, + .endianness = IIO_BE, + }, + }, + { + .type = IIO_INTENSITY, + .channel2 = IIO_MOD_LIGHT_IR, + .modified = 1, + + .scan_index = 1, + .scan_type = { + .sign = 'u', + .shift = 8, + .realbits = 18, + .storagebits = 32, + .endianness = IIO_BE, + }, + }, + { + .type = IIO_TEMP, + .info_mask_separate = + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), + .scan_index = -1, + }, +}; + +static int max30102_set_powermode(struct max30102_data *data, bool state) +{ + return regmap_update_bits(data->regmap, MAX30102_REG_MODE_CONFIG, + MAX30102_REG_MODE_CONFIG_PWR, + state ? 0 : MAX30102_REG_MODE_CONFIG_PWR); +} + +static int max30102_buffer_postenable(struct iio_dev *indio_dev) +{ + struct max30102_data *data = iio_priv(indio_dev); + + return max30102_set_powermode(data, true); +} + +static int max30102_buffer_predisable(struct iio_dev *indio_dev) +{ + struct max30102_data *data = iio_priv(indio_dev); + + return max30102_set_powermode(data, false); +} + +static const struct iio_buffer_setup_ops max30102_buffer_setup_ops = { + .postenable = max30102_buffer_postenable, + .predisable = max30102_buffer_predisable, +}; + +static inline int max30102_fifo_count(struct max30102_data *data) +{ + unsigned int val; + int ret; + + ret = regmap_read(data->regmap, MAX30102_REG_INT_STATUS, &val); + if (ret) + return ret; + + /* FIFO has one sample slot left */ + if (val & MAX30102_REG_INT_STATUS_FIFO_RDY) + return 1; + + return 0; +} + +static int max30102_read_measurement(struct max30102_data *data) +{ + int ret; + u8 *buffer = (u8 *) &data->buffer; + + ret = i2c_smbus_read_i2c_block_data(data->client, + MAX30102_REG_FIFO_DATA, + MAX30102_REG_FIFO_DATA_ENTRY_LEN, + buffer); + + memcpy(&data->processed_buffer[0], &buffer[0], 3); + memcpy(&data->processed_buffer[1], &buffer[3], 3); + + return (ret == MAX30102_REG_FIFO_DATA_ENTRY_LEN) ? 0 : -EINVAL; +} + +static irqreturn_t max30102_interrupt_handler(int irq, void *private) +{ + struct iio_dev *indio_dev = private; + struct max30102_data *data = iio_priv(indio_dev); + int ret, cnt = 0; + + mutex_lock(&data->lock); + + while (cnt || (cnt = max30102_fifo_count(data)) > 0) { + ret = max30102_read_measurement(data); + if (ret) + break; + + iio_push_to_buffers(data->indio_dev, data->processed_buffer); + cnt--; + } + + mutex_unlock(&data->lock); + + return IRQ_HANDLED; +} + +static int max30102_get_current_idx(unsigned int val, int *reg) +{ + /* each step is 0.200 mA */ + *reg = val / 200; + + return *reg > 0xff ? -EINVAL : 0; +} + +static int max30102_led_init(struct max30102_data *data) +{ + struct device *dev = &data->client->dev; + struct device_node *np = dev->of_node; + unsigned int val; + int reg, ret; + + ret = of_property_read_u32(np, "maxim,red-led-current-microamp", &val); + if (ret) { + dev_info(dev, "no red-led-current-microamp set\n"); + + /* Default to 7 mA RED LED */ + val = 7000; + } + + ret = max30102_get_current_idx(val, ®); + if (ret) { + dev_err(dev, "invalid RED LED current setting %d\n", val); + return ret; + } + + ret = regmap_write(data->regmap, MAX30102_REG_RED_LED_CONFIG, reg); + if (ret) + return ret; + + ret = of_property_read_u32(np, "maxim,ir-led-current-microamp", &val); + if (ret) { + dev_info(dev, "no ir-led-current-microamp set\n"); + + /* Default to 7 mA IR LED */ + val = 7000; + } + + ret = max30102_get_current_idx(val, ®); + if (ret) { + dev_err(dev, "invalid IR LED current setting %d", val); + return ret; + } + + return regmap_write(data->regmap, MAX30102_REG_IR_LED_CONFIG, reg); +} + +static int max30102_chip_init(struct max30102_data *data) +{ + int ret; + + /* setup LED current settings */ + ret = max30102_led_init(data); + if (ret) + return ret; + + /* enable 18-bit HR + SPO2 readings at 400Hz */ + ret = regmap_write(data->regmap, MAX30102_REG_SPO2_CONFIG, + (MAX30102_REG_SPO2_CONFIG_ADC_4096_STEPS + << MAX30102_REG_SPO2_CONFIG_ADC_MASK_SHIFT) | + (MAX30102_REG_SPO2_CONFIG_SR_400HZ + << MAX30102_REG_SPO2_CONFIG_SR_MASK_SHIFT) | + MAX30102_REG_SPO2_CONFIG_PULSE_411_US); + if (ret) + return ret; + + /* enable SPO2 mode */ + ret = regmap_update_bits(data->regmap, MAX30102_REG_MODE_CONFIG, + MAX30102_REG_MODE_CONFIG_MODE_MASK, + MAX30102_REG_MODE_CONFIG_MODE_HR_EN | + MAX30102_REG_MODE_CONFIG_MODE_SPO2_EN); + if (ret) + return ret; + + /* average 4 samples + generate FIFO interrupt */ + ret = regmap_write(data->regmap, MAX30102_REG_FIFO_CONFIG, + (MAX30102_REG_FIFO_CONFIG_AVG_4SAMPLES + << MAX30102_REG_FIFO_CONFIG_AVG_SHIFT) | + MAX30102_REG_FIFO_CONFIG_AFULL); + if (ret) + return ret; + + /* enable FIFO interrupt */ + return regmap_update_bits(data->regmap, MAX30102_REG_INT_ENABLE, + MAX30102_REG_INT_ENABLE_MASK, + MAX30102_REG_INT_ENABLE_FIFO_EN); +} + +static int max30102_read_temp(struct max30102_data *data, int *val) +{ + int ret; + unsigned int reg; + + ret = regmap_read(data->regmap, MAX30102_REG_TEMP_INTEGER, ®); + if (ret < 0) + return ret; + *val = reg << 4; + + ret = regmap_read(data->regmap, MAX30102_REG_TEMP_FRACTION, ®); + if (ret < 0) + return ret; + + *val |= reg & 0xf; + *val = sign_extend32(*val, 11); + + return 0; +} + +static int max30102_get_temp(struct max30102_data *data, int *val) +{ + int ret; + + /* start acquisition */ + ret = regmap_update_bits(data->regmap, MAX30102_REG_TEMP_CONFIG, + MAX30102_REG_TEMP_CONFIG_TEMP_EN, + MAX30102_REG_TEMP_CONFIG_TEMP_EN); + if (ret) + return ret; + + msleep(35); + + return max30102_read_temp(data, val); +} + +static int max30102_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct max30102_data *data = iio_priv(indio_dev); + int ret = -EINVAL; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + /* + * Temperature reading can only be acquired while engine + * is running + */ + mutex_lock(&indio_dev->mlock); + + if (!iio_buffer_enabled(indio_dev)) + ret = -EBUSY; + else { + ret = max30102_get_temp(data, val); + if (!ret) + ret = IIO_VAL_INT; + } + + mutex_unlock(&indio_dev->mlock); + break; + case IIO_CHAN_INFO_SCALE: + *val = 1; /* 0.0625 */ + *val2 = 16; + ret = IIO_VAL_FRACTIONAL; + break; + } + + return ret; +} + +static const struct iio_info max30102_info = { + .driver_module = THIS_MODULE, + .read_raw = max30102_read_raw, +}; + +static int max30102_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct max30102_data *data; + struct iio_buffer *buffer; + struct iio_dev *indio_dev; + int ret; + + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); + if (!indio_dev) + return -ENOMEM; + + buffer = devm_iio_kfifo_allocate(&client->dev); + if (!buffer) + return -ENOMEM; + + iio_device_attach_buffer(indio_dev, buffer); + + indio_dev->name = MAX30102_DRV_NAME; + indio_dev->channels = max30102_channels; + indio_dev->info = &max30102_info; + indio_dev->num_channels = ARRAY_SIZE(max30102_channels); + indio_dev->available_scan_masks = max30102_scan_masks; + indio_dev->modes = (INDIO_BUFFER_SOFTWARE | INDIO_DIRECT_MODE); + indio_dev->setup_ops = &max30102_buffer_setup_ops; + + data = iio_priv(indio_dev); + data->indio_dev = indio_dev; + data->client = client; + + mutex_init(&data->lock); + i2c_set_clientdata(client, indio_dev); + + data->regmap = devm_regmap_init_i2c(client, &max30102_regmap_config); + if (IS_ERR(data->regmap)) { + dev_err(&client->dev, "regmap initialization failed.\n"); + return PTR_ERR(data->regmap); + } + max30102_set_powermode(data, false); + + ret = max30102_chip_init(data); + if (ret) + return ret; + + if (client->irq <= 0) { + dev_err(&client->dev, "no valid irq defined\n"); + return -EINVAL; + } + + ret = devm_request_threaded_irq(&client->dev, client->irq, + NULL, max30102_interrupt_handler, + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + "max30102_irq", indio_dev); + if (ret) { + dev_err(&client->dev, "request irq (%d) failed\n", client->irq); + return ret; + } + + return iio_device_register(indio_dev); +} + +static int max30102_remove(struct i2c_client *client) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(client); + struct max30102_data *data = iio_priv(indio_dev); + + iio_device_unregister(indio_dev); + max30102_set_powermode(data, false); + + return 0; +} + +static const struct i2c_device_id max30102_id[] = { + { "max30102", 0 }, + {} +}; +MODULE_DEVICE_TABLE(i2c, max30102_id); + +static const struct of_device_id max30102_dt_ids[] = { + { .compatible = "maxim,max30102" }, + { } +}; +MODULE_DEVICE_TABLE(of, max30102_dt_ids); + +static struct i2c_driver max30102_driver = { + .driver = { + .name = MAX30102_DRV_NAME, + .of_match_table = of_match_ptr(max30102_dt_ids), + }, + .probe = max30102_probe, + .remove = max30102_remove, + .id_table = max30102_id, +}; +module_i2c_driver(max30102_driver); + +MODULE_AUTHOR("Matt Ranostay <matt@ranostay.consulting>"); +MODULE_DESCRIPTION("MAX30102 heart rate and pulse oximeter sensor"); +MODULE_LICENSE("GPL"); -- 2.10.2 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v3 2/2] iio: health: add MAX30102 oximeter driver support 2017-02-04 10:22 ` [PATCH v3 2/2] iio: health: add MAX30102 oximeter driver support Matt Ranostay @ 2017-02-05 9:46 ` Jonathan Cameron 0 siblings, 0 replies; 4+ messages in thread From: Jonathan Cameron @ 2017-02-05 9:46 UTC (permalink / raw) To: Matt Ranostay, linux-iio On 04/02/17 10:22, Matt Ranostay wrote: > MAX30102 is an heart rate and pulse oximeter sensor that works using > two LEDS of different wavelengths, and detecting the light reflected > back. > > This patchset adds support for both IR and RED LED channels which can > be processed in userspace to determine heart rate and blood oxygen > levels. The MAX30102 part isn't completely register and functional > compatible with the existing MAX30100 driver. > > Signed-off-by: Matt Ranostay <matt@ranostay.consulting> Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it. Thanks, Jonathan > --- > drivers/iio/health/Kconfig | 13 ++ > drivers/iio/health/Makefile | 1 + > drivers/iio/health/max30102.c | 485 ++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 499 insertions(+) > create mode 100644 drivers/iio/health/max30102.c > > Changes from v1: > * add newlines to dev_err/dev_info statements > * update documentation to 400hz samples, but actually 100hz to FIFO > * fix storage bits to a power of 2, and the required buffer processing > * fixed return code from max30102_read_measurement() > > Changes from v2: > * correct shift value in MAX30102_REG_SPO2_CONFIG_ADC_MASK_SHIFT > * changed iio_buffed_enabled() error from -EAGAIN to -EBUSY > > diff --git a/drivers/iio/health/Kconfig b/drivers/iio/health/Kconfig > index c5f004a8e447..a2ecb4c94c2a 100644 > --- a/drivers/iio/health/Kconfig > +++ b/drivers/iio/health/Kconfig > @@ -46,6 +46,19 @@ config MAX30100 > To compile this driver as a module, choose M here: the > module will be called max30100. > > +config MAX30102 > + tristate "MAX30102 heart rate and pulse oximeter sensor" > + depends on I2C > + select REGMAP_I2C > + select IIO_BUFFER > + select IIO_KFIFO_BUF > + help > + Say Y here to build I2C interface support for the Maxim > + MAX30102 heart rate, and pulse oximeter sensor. > + > + To compile this driver as a module, choose M here: the > + module will be called max30102. > + > endmenu > > endmenu > diff --git a/drivers/iio/health/Makefile b/drivers/iio/health/Makefile > index 9955a2ae8df1..3558f9d64954 100644 > --- a/drivers/iio/health/Makefile > +++ b/drivers/iio/health/Makefile > @@ -7,3 +7,4 @@ > obj-$(CONFIG_AFE4403) += afe4403.o > obj-$(CONFIG_AFE4404) += afe4404.o > obj-$(CONFIG_MAX30100) += max30100.o > +obj-$(CONFIG_MAX30102) += max30102.o > diff --git a/drivers/iio/health/max30102.c b/drivers/iio/health/max30102.c > new file mode 100644 > index 000000000000..377518c15552 > --- /dev/null > +++ b/drivers/iio/health/max30102.c > @@ -0,0 +1,485 @@ > +/* > + * max30102.c - Support for MAX30102 heart rate and pulse oximeter sensor > + * > + * Copyright (C) 2017 Matt Ranostay <matt@ranostay.consulting> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * TODO: proximity power saving feature > + */ > + > +#include <linux/module.h> > +#include <linux/init.h> > +#include <linux/interrupt.h> > +#include <linux/delay.h> > +#include <linux/err.h> > +#include <linux/irq.h> > +#include <linux/i2c.h> > +#include <linux/mutex.h> > +#include <linux/of.h> > +#include <linux/regmap.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/buffer.h> > +#include <linux/iio/kfifo_buf.h> > + > +#define MAX30102_REGMAP_NAME "max30102_regmap" > +#define MAX30102_DRV_NAME "max30102" > + > +#define MAX30102_REG_INT_STATUS 0x00 > +#define MAX30102_REG_INT_STATUS_PWR_RDY BIT(0) > +#define MAX30102_REG_INT_STATUS_PROX_INT BIT(4) > +#define MAX30102_REG_INT_STATUS_ALC_OVF BIT(5) > +#define MAX30102_REG_INT_STATUS_PPG_RDY BIT(6) > +#define MAX30102_REG_INT_STATUS_FIFO_RDY BIT(7) > + > +#define MAX30102_REG_INT_ENABLE 0x02 > +#define MAX30102_REG_INT_ENABLE_PROX_INT_EN BIT(4) > +#define MAX30102_REG_INT_ENABLE_ALC_OVF_EN BIT(5) > +#define MAX30102_REG_INT_ENABLE_PPG_EN BIT(6) > +#define MAX30102_REG_INT_ENABLE_FIFO_EN BIT(7) > +#define MAX30102_REG_INT_ENABLE_MASK 0xf0 > +#define MAX30102_REG_INT_ENABLE_MASK_SHIFT 4 > + > +#define MAX30102_REG_FIFO_WR_PTR 0x04 > +#define MAX30102_REG_FIFO_OVR_CTR 0x05 > +#define MAX30102_REG_FIFO_RD_PTR 0x06 > +#define MAX30102_REG_FIFO_DATA 0x07 > +#define MAX30102_REG_FIFO_DATA_ENTRY_LEN 6 > + > +#define MAX30102_REG_FIFO_CONFIG 0x08 > +#define MAX30102_REG_FIFO_CONFIG_AVG_4SAMPLES BIT(1) > +#define MAX30102_REG_FIFO_CONFIG_AVG_SHIFT 5 > +#define MAX30102_REG_FIFO_CONFIG_AFULL BIT(0) > + > +#define MAX30102_REG_MODE_CONFIG 0x09 > +#define MAX30102_REG_MODE_CONFIG_MODE_SPO2_EN BIT(0) > +#define MAX30102_REG_MODE_CONFIG_MODE_HR_EN BIT(1) > +#define MAX30102_REG_MODE_CONFIG_MODE_MASK 0x03 > +#define MAX30102_REG_MODE_CONFIG_PWR BIT(7) > + > +#define MAX30102_REG_SPO2_CONFIG 0x0a > +#define MAX30102_REG_SPO2_CONFIG_PULSE_411_US 0x03 > +#define MAX30102_REG_SPO2_CONFIG_SR_400HZ 0x03 > +#define MAX30102_REG_SPO2_CONFIG_SR_MASK 0x07 > +#define MAX30102_REG_SPO2_CONFIG_SR_MASK_SHIFT 2 > +#define MAX30102_REG_SPO2_CONFIG_ADC_4096_STEPS BIT(0) > +#define MAX30102_REG_SPO2_CONFIG_ADC_MASK_SHIFT 5 > + > +#define MAX30102_REG_RED_LED_CONFIG 0x0c > +#define MAX30102_REG_IR_LED_CONFIG 0x0d > + > +#define MAX30102_REG_TEMP_CONFIG 0x21 > +#define MAX30102_REG_TEMP_CONFIG_TEMP_EN BIT(0) > + > +#define MAX30102_REG_TEMP_INTEGER 0x1f > +#define MAX30102_REG_TEMP_FRACTION 0x20 > + > +struct max30102_data { > + struct i2c_client *client; > + struct iio_dev *indio_dev; > + struct mutex lock; > + struct regmap *regmap; > + > + u8 buffer[8]; > + __be32 processed_buffer[2]; /* 2 x 18-bit (padded to 32-bits) */ > +}; > + > +static const struct regmap_config max30102_regmap_config = { > + .name = MAX30102_REGMAP_NAME, > + > + .reg_bits = 8, > + .val_bits = 8, > +}; > + > +static const unsigned long max30102_scan_masks[] = {0x3, 0}; > + > +static const struct iio_chan_spec max30102_channels[] = { > + { > + .type = IIO_INTENSITY, > + .channel2 = IIO_MOD_LIGHT_RED, > + .modified = 1, > + > + .scan_index = 0, > + .scan_type = { > + .sign = 'u', > + .shift = 8, > + .realbits = 18, > + .storagebits = 32, > + .endianness = IIO_BE, > + }, > + }, > + { > + .type = IIO_INTENSITY, > + .channel2 = IIO_MOD_LIGHT_IR, > + .modified = 1, > + > + .scan_index = 1, > + .scan_type = { > + .sign = 'u', > + .shift = 8, > + .realbits = 18, > + .storagebits = 32, > + .endianness = IIO_BE, > + }, > + }, > + { > + .type = IIO_TEMP, > + .info_mask_separate = > + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), > + .scan_index = -1, > + }, > +}; > + > +static int max30102_set_powermode(struct max30102_data *data, bool state) > +{ > + return regmap_update_bits(data->regmap, MAX30102_REG_MODE_CONFIG, > + MAX30102_REG_MODE_CONFIG_PWR, > + state ? 0 : MAX30102_REG_MODE_CONFIG_PWR); > +} > + > +static int max30102_buffer_postenable(struct iio_dev *indio_dev) > +{ > + struct max30102_data *data = iio_priv(indio_dev); > + > + return max30102_set_powermode(data, true); > +} > + > +static int max30102_buffer_predisable(struct iio_dev *indio_dev) > +{ > + struct max30102_data *data = iio_priv(indio_dev); > + > + return max30102_set_powermode(data, false); > +} > + > +static const struct iio_buffer_setup_ops max30102_buffer_setup_ops = { > + .postenable = max30102_buffer_postenable, > + .predisable = max30102_buffer_predisable, > +}; > + > +static inline int max30102_fifo_count(struct max30102_data *data) > +{ > + unsigned int val; > + int ret; > + > + ret = regmap_read(data->regmap, MAX30102_REG_INT_STATUS, &val); > + if (ret) > + return ret; > + > + /* FIFO has one sample slot left */ > + if (val & MAX30102_REG_INT_STATUS_FIFO_RDY) > + return 1; > + > + return 0; > +} > + > +static int max30102_read_measurement(struct max30102_data *data) > +{ > + int ret; > + u8 *buffer = (u8 *) &data->buffer; > + > + ret = i2c_smbus_read_i2c_block_data(data->client, > + MAX30102_REG_FIFO_DATA, > + MAX30102_REG_FIFO_DATA_ENTRY_LEN, > + buffer); > + > + memcpy(&data->processed_buffer[0], &buffer[0], 3); > + memcpy(&data->processed_buffer[1], &buffer[3], 3); > + > + return (ret == MAX30102_REG_FIFO_DATA_ENTRY_LEN) ? 0 : -EINVAL; > +} > + > +static irqreturn_t max30102_interrupt_handler(int irq, void *private) > +{ > + struct iio_dev *indio_dev = private; > + struct max30102_data *data = iio_priv(indio_dev); > + int ret, cnt = 0; > + > + mutex_lock(&data->lock); > + > + while (cnt || (cnt = max30102_fifo_count(data)) > 0) { > + ret = max30102_read_measurement(data); > + if (ret) > + break; > + > + iio_push_to_buffers(data->indio_dev, data->processed_buffer); > + cnt--; > + } > + > + mutex_unlock(&data->lock); > + > + return IRQ_HANDLED; > +} > + > +static int max30102_get_current_idx(unsigned int val, int *reg) > +{ > + /* each step is 0.200 mA */ > + *reg = val / 200; > + > + return *reg > 0xff ? -EINVAL : 0; > +} > + > +static int max30102_led_init(struct max30102_data *data) > +{ > + struct device *dev = &data->client->dev; > + struct device_node *np = dev->of_node; > + unsigned int val; > + int reg, ret; > + > + ret = of_property_read_u32(np, "maxim,red-led-current-microamp", &val); > + if (ret) { > + dev_info(dev, "no red-led-current-microamp set\n"); > + > + /* Default to 7 mA RED LED */ > + val = 7000; > + } > + > + ret = max30102_get_current_idx(val, ®); > + if (ret) { > + dev_err(dev, "invalid RED LED current setting %d\n", val); > + return ret; > + } > + > + ret = regmap_write(data->regmap, MAX30102_REG_RED_LED_CONFIG, reg); > + if (ret) > + return ret; > + > + ret = of_property_read_u32(np, "maxim,ir-led-current-microamp", &val); > + if (ret) { > + dev_info(dev, "no ir-led-current-microamp set\n"); > + > + /* Default to 7 mA IR LED */ > + val = 7000; > + } > + > + ret = max30102_get_current_idx(val, ®); > + if (ret) { > + dev_err(dev, "invalid IR LED current setting %d", val); > + return ret; > + } > + > + return regmap_write(data->regmap, MAX30102_REG_IR_LED_CONFIG, reg); > +} > + > +static int max30102_chip_init(struct max30102_data *data) > +{ > + int ret; > + > + /* setup LED current settings */ > + ret = max30102_led_init(data); > + if (ret) > + return ret; > + > + /* enable 18-bit HR + SPO2 readings at 400Hz */ > + ret = regmap_write(data->regmap, MAX30102_REG_SPO2_CONFIG, > + (MAX30102_REG_SPO2_CONFIG_ADC_4096_STEPS > + << MAX30102_REG_SPO2_CONFIG_ADC_MASK_SHIFT) | > + (MAX30102_REG_SPO2_CONFIG_SR_400HZ > + << MAX30102_REG_SPO2_CONFIG_SR_MASK_SHIFT) | > + MAX30102_REG_SPO2_CONFIG_PULSE_411_US); > + if (ret) > + return ret; > + > + /* enable SPO2 mode */ > + ret = regmap_update_bits(data->regmap, MAX30102_REG_MODE_CONFIG, > + MAX30102_REG_MODE_CONFIG_MODE_MASK, > + MAX30102_REG_MODE_CONFIG_MODE_HR_EN | > + MAX30102_REG_MODE_CONFIG_MODE_SPO2_EN); > + if (ret) > + return ret; > + > + /* average 4 samples + generate FIFO interrupt */ > + ret = regmap_write(data->regmap, MAX30102_REG_FIFO_CONFIG, > + (MAX30102_REG_FIFO_CONFIG_AVG_4SAMPLES > + << MAX30102_REG_FIFO_CONFIG_AVG_SHIFT) | > + MAX30102_REG_FIFO_CONFIG_AFULL); > + if (ret) > + return ret; > + > + /* enable FIFO interrupt */ > + return regmap_update_bits(data->regmap, MAX30102_REG_INT_ENABLE, > + MAX30102_REG_INT_ENABLE_MASK, > + MAX30102_REG_INT_ENABLE_FIFO_EN); > +} > + > +static int max30102_read_temp(struct max30102_data *data, int *val) > +{ > + int ret; > + unsigned int reg; > + > + ret = regmap_read(data->regmap, MAX30102_REG_TEMP_INTEGER, ®); > + if (ret < 0) > + return ret; > + *val = reg << 4; > + > + ret = regmap_read(data->regmap, MAX30102_REG_TEMP_FRACTION, ®); > + if (ret < 0) > + return ret; > + > + *val |= reg & 0xf; > + *val = sign_extend32(*val, 11); > + > + return 0; > +} > + > +static int max30102_get_temp(struct max30102_data *data, int *val) > +{ > + int ret; > + > + /* start acquisition */ > + ret = regmap_update_bits(data->regmap, MAX30102_REG_TEMP_CONFIG, > + MAX30102_REG_TEMP_CONFIG_TEMP_EN, > + MAX30102_REG_TEMP_CONFIG_TEMP_EN); > + if (ret) > + return ret; > + > + msleep(35); > + > + return max30102_read_temp(data, val); > +} > + > +static int max30102_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, > + int *val, int *val2, long mask) > +{ > + struct max30102_data *data = iio_priv(indio_dev); > + int ret = -EINVAL; > + > + switch (mask) { > + case IIO_CHAN_INFO_RAW: > + /* > + * Temperature reading can only be acquired while engine > + * is running > + */ > + mutex_lock(&indio_dev->mlock); > + > + if (!iio_buffer_enabled(indio_dev)) > + ret = -EBUSY; > + else { > + ret = max30102_get_temp(data, val); > + if (!ret) > + ret = IIO_VAL_INT; > + } > + > + mutex_unlock(&indio_dev->mlock); > + break; > + case IIO_CHAN_INFO_SCALE: > + *val = 1; /* 0.0625 */ > + *val2 = 16; > + ret = IIO_VAL_FRACTIONAL; > + break; > + } > + > + return ret; > +} > + > +static const struct iio_info max30102_info = { > + .driver_module = THIS_MODULE, > + .read_raw = max30102_read_raw, > +}; > + > +static int max30102_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + struct max30102_data *data; > + struct iio_buffer *buffer; > + struct iio_dev *indio_dev; > + int ret; > + > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); > + if (!indio_dev) > + return -ENOMEM; > + > + buffer = devm_iio_kfifo_allocate(&client->dev); > + if (!buffer) > + return -ENOMEM; > + > + iio_device_attach_buffer(indio_dev, buffer); > + > + indio_dev->name = MAX30102_DRV_NAME; > + indio_dev->channels = max30102_channels; > + indio_dev->info = &max30102_info; > + indio_dev->num_channels = ARRAY_SIZE(max30102_channels); > + indio_dev->available_scan_masks = max30102_scan_masks; > + indio_dev->modes = (INDIO_BUFFER_SOFTWARE | INDIO_DIRECT_MODE); > + indio_dev->setup_ops = &max30102_buffer_setup_ops; > + > + data = iio_priv(indio_dev); > + data->indio_dev = indio_dev; > + data->client = client; > + > + mutex_init(&data->lock); > + i2c_set_clientdata(client, indio_dev); > + > + data->regmap = devm_regmap_init_i2c(client, &max30102_regmap_config); > + if (IS_ERR(data->regmap)) { > + dev_err(&client->dev, "regmap initialization failed.\n"); > + return PTR_ERR(data->regmap); > + } > + max30102_set_powermode(data, false); > + > + ret = max30102_chip_init(data); > + if (ret) > + return ret; > + > + if (client->irq <= 0) { > + dev_err(&client->dev, "no valid irq defined\n"); > + return -EINVAL; > + } > + > + ret = devm_request_threaded_irq(&client->dev, client->irq, > + NULL, max30102_interrupt_handler, > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > + "max30102_irq", indio_dev); > + if (ret) { > + dev_err(&client->dev, "request irq (%d) failed\n", client->irq); > + return ret; > + } > + > + return iio_device_register(indio_dev); > +} > + > +static int max30102_remove(struct i2c_client *client) > +{ > + struct iio_dev *indio_dev = i2c_get_clientdata(client); > + struct max30102_data *data = iio_priv(indio_dev); > + > + iio_device_unregister(indio_dev); > + max30102_set_powermode(data, false); > + > + return 0; > +} > + > +static const struct i2c_device_id max30102_id[] = { > + { "max30102", 0 }, > + {} > +}; > +MODULE_DEVICE_TABLE(i2c, max30102_id); > + > +static const struct of_device_id max30102_dt_ids[] = { > + { .compatible = "maxim,max30102" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, max30102_dt_ids); > + > +static struct i2c_driver max30102_driver = { > + .driver = { > + .name = MAX30102_DRV_NAME, > + .of_match_table = of_match_ptr(max30102_dt_ids), > + }, > + .probe = max30102_probe, > + .remove = max30102_remove, > + .id_table = max30102_id, > +}; > +module_i2c_driver(max30102_driver); > + > +MODULE_AUTHOR("Matt Ranostay <matt@ranostay.consulting>"); > +MODULE_DESCRIPTION("MAX30102 heart rate and pulse oximeter sensor"); > +MODULE_LICENSE("GPL"); > ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH v3 1/2] devicetree: add documentation for MAX30102 oximeter 2017-02-04 10:22 [PATCH v3 1/2] devicetree: add documentation for MAX30102 oximeter Matt Ranostay 2017-02-04 10:22 ` [PATCH v3 2/2] iio: health: add MAX30102 oximeter driver support Matt Ranostay @ 2017-02-05 9:45 ` Jonathan Cameron 1 sibling, 0 replies; 4+ messages in thread From: Jonathan Cameron @ 2017-02-05 9:45 UTC (permalink / raw) To: Matt Ranostay, linux-iio On 04/02/17 10:22, Matt Ranostay wrote: > Acked-by: Rob Herring <robh@kernel.org> > Signed-off-by: Matt Ranostay <matt@ranostay.consulting> Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it. Thanks, Jonathan > --- > .../devicetree/bindings/iio/health/max30102.txt | 30 ++++++++++++++++++++++ > 1 file changed, 30 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/health/max30102.txt > > Changes from v1: > * none > > Changes from v2: > * none > > diff --git a/Documentation/devicetree/bindings/iio/health/max30102.txt b/Documentation/devicetree/bindings/iio/health/max30102.txt > new file mode 100644 > index 000000000000..c695e7cbeefb > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/health/max30102.txt > @@ -0,0 +1,30 @@ > +Maxim MAX30102 heart rate and pulse oximeter sensor > + > +* https://datasheets.maximintegrated.com/en/ds/MAX30102.pdf > + > +Required properties: > + - compatible: must be "maxim,max30102" > + - reg: the I2C address of the sensor > + - interrupt-parent: should be the phandle for the interrupt controller > + - interrupts: the sole interrupt generated by the device > + > + Refer to interrupt-controller/interrupts.txt for generic > + interrupt client node bindings. > + > +Optional properties: > + - maxim,red-led-current-microamp: configuration for RED LED current > + - maxim,ir-led-current-microamp: configuration for IR LED current > + > + Note that each step is approximately 200 microamps, ranging from 0 uA to > + 50800 uA. > + > +Example: > + > +max30100@57 { > + compatible = "maxim,max30102"; > + reg = <0x57>; > + maxim,red-led-current-microamp = <7000>; > + maxim,ir-led-current-microamp = <7000>; > + interrupt-parent = <&gpio1>; > + interrupts = <16 2>; > +}; > ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2017-02-05 9:46 UTC | newest] Thread overview: 4+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2017-02-04 10:22 [PATCH v3 1/2] devicetree: add documentation for MAX30102 oximeter Matt Ranostay 2017-02-04 10:22 ` [PATCH v3 2/2] iio: health: add MAX30102 oximeter driver support Matt Ranostay 2017-02-05 9:46 ` Jonathan Cameron 2017-02-05 9:45 ` [PATCH v3 1/2] devicetree: add documentation for MAX30102 oximeter Jonathan Cameron
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).