From: Daniel Kurtz <djkurtz@chromium.org>
To: Dmitry Torokhov <dmitry.torokhov@gmail.com>,
Joonyoung Shim <jy0922.shim@samsung.com>,
Iiro Valkonen <iiro.valkonen@atmel.com>,
Henrik Rydberg <rydberg@euromail.se>,
linux-input@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Benson Leung <bleung@chromium.org>,
Yufeng Shen <miletus@chromium.org>,
Daniel Kurtz <djkurtz@chromium.org>
Subject: [PATCH 00/20] cleanup atmel_mxt_ts
Date: Tue, 13 Mar 2012 20:04:03 +0800 [thread overview]
Message-ID: <1331640263-18935-1-git-send-email-djkurtz@chromium.org> (raw)
This patchset cleans up the atmel_mxt_ts touchscreen driver.
In particular, it addresses the following issues:
1) sysfs
a) fw_update only by root
b) allow writing config
c) add backupnv to save config to device flash
2) faster initialization
a) read/write sets of registers using i2c block transactions
b) fetch object table as a set of i2c reads, one per object
c) write config data as a set of i2c writes, one per object
3) faster interrupt processing & initialization times
a) cache important values at init instead of computing in isr
b) don't read message checksum byte (which isn't even enabled in fw)
c) read num messages first, instead of looking for 0xFF reportid
d) read all pending message bytes in one i2c read transaction
4) more correct MT-B support
a) send all (changed) contacts in a single EV_SYN/SYN_REPORT
Daniel Kurtz (20):
Input: atmel_mxt_ts - use CONFIG_PM_SLEEP
Input: atmel_mxt_ts - only allow root to update firmware
Input: atmel_mxt_ts - verify object size in mxt_write_object
Input: atmel_mxt_ts - refactor mxt_read/write_reg to take a length
Input: atmel_mxt_ts - dump mxt_read/write_reg
Input: atmel_mxt_ts - allow writing to object sysfs entry
Input: atmel_mxt_ts - add backupnv sysfs entry
Input: atmel_mxt_ts - store actual size and instance
Input: atmel_mxt_ts - do not read extra (checksum) byte
Input: atmel_mxt_ts - dump each message on just 1 line
Input: atmel_mxt_ts - refactor mxt_object_show
Input: atmel_mxt_ts - simplify event reporting
Input: atmel_mxt_ts - parse vector field of data packets
Input: atmel_mxt_ts - refactor reading object table
Input: atmel_mxt_ts - optimize writing of object table entries
Input: atmel_mxt_ts - refactor get info
Input: atmel_mxt_ts - use cached T9 reportid range in isr
Input: atmel_mxt_ts - read num messages, then all messages
Input: atmel_mxt_ts - remove mxt_make_highchg and parse T6 report
Input: atmel_mxt_ts - send all MT-B slots in one input report
drivers/input/touchscreen/atmel_mxt_ts.c | 590 +++++++++++++++---------------
1 files changed, 286 insertions(+), 304 deletions(-)
--
1.7.7.3
next reply other threads:[~2012-03-13 12:04 UTC|newest]
Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-03-13 12:04 Daniel Kurtz [this message]
2012-03-13 12:04 ` [PATCH 01/20] Input: atmel_mxt_ts - use CONFIG_PM_SLEEP Daniel Kurtz
2012-03-13 12:04 ` [PATCH 02/20] Input: atmel_mxt_ts - only allow root to update firmware Daniel Kurtz
2012-03-20 14:38 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 03/20] Input: atmel_mxt_ts - verify object size in mxt_write_object Daniel Kurtz
2012-03-14 1:33 ` Joonyoung Shim
2012-03-14 2:13 ` Daniel Kurtz
2012-03-14 2:37 ` Joonyoung Shim
2012-03-13 12:04 ` [PATCH 04/20] Input: atmel_mxt_ts - refactor mxt_read/write_reg to take a length Daniel Kurtz
2012-03-13 12:04 ` [PATCH 05/20] Input: atmel_mxt_ts - dump mxt_read/write_reg Daniel Kurtz
2012-03-20 14:43 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 06/20] Input: atmel_mxt_ts - allow writing to object sysfs entry Daniel Kurtz
2012-03-19 8:04 ` Henrik Rydberg
2012-03-19 8:26 ` Daniel Kurtz
2012-03-20 14:51 ` Nick Dyer
2012-03-20 23:03 ` Alan Cox
2012-03-20 23:32 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 07/20] Input: atmel_mxt_ts - add backupnv " Daniel Kurtz
2012-03-20 15:01 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 08/20] Input: atmel_mxt_ts - store actual size and instance Daniel Kurtz
2012-03-20 15:05 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 09/20] Input: atmel_mxt_ts - do not read extra (checksum) byte Daniel Kurtz
2012-03-20 15:07 ` Nick Dyer
2012-03-22 10:18 ` Bowens, Alan
2012-03-13 12:04 ` [PATCH 10/20] Input: atmel_mxt_ts - dump each message on just 1 line Daniel Kurtz
2012-03-20 15:08 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 11/20] Input: atmel_mxt_ts - refactor mxt_object_show Daniel Kurtz
2012-03-20 15:11 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 12/20] Input: atmel_mxt_ts - simplify event reporting Daniel Kurtz
2012-03-19 8:26 ` Henrik Rydberg
2012-03-19 9:06 ` Daniel Kurtz
2012-03-20 15:13 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 13/20] Input: atmel_mxt_ts - parse vector field of data packets Daniel Kurtz
2012-03-20 15:23 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 14/20] Input: atmel_mxt_ts - refactor reading object table Daniel Kurtz
2012-03-20 15:19 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 15/20] Input: atmel_mxt_ts - optimize writing of object table entries Daniel Kurtz
2012-03-13 12:04 ` [PATCH 16/20] Input: atmel_mxt_ts - refactor get info Daniel Kurtz
2012-03-20 15:21 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 17/20] Input: atmel_mxt_ts - use cached T9 reportid range in isr Daniel Kurtz
2012-03-20 15:30 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 18/20] Input: atmel_mxt_ts - read num messages, then all messages Daniel Kurtz
2012-03-14 2:32 ` Joonyoung Shim
2012-03-14 3:13 ` Daniel Kurtz
2012-03-20 15:28 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 19/20] Input: atmel_mxt_ts - remove mxt_make_highchg and parse T6 report Daniel Kurtz
2012-03-20 15:38 ` Nick Dyer
2012-03-29 15:20 ` Daniel Kurtz
2012-03-30 7:00 ` Nick Dyer
2012-03-13 12:04 ` [PATCH 20/20] Input: atmel_mxt_ts - send all MT-B slots in one input report Daniel Kurtz
2012-03-20 15:39 ` Nick Dyer
2012-03-14 2:43 ` [PATCH 00/20] cleanup atmel_mxt_ts Joonyoung Shim
2012-03-14 17:00 ` Valkonen, Iiro
2012-03-20 14:33 ` Nick Dyer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1331640263-18935-1-git-send-email-djkurtz@chromium.org \
--to=djkurtz@chromium.org \
--cc=bleung@chromium.org \
--cc=dmitry.torokhov@gmail.com \
--cc=iiro.valkonen@atmel.com \
--cc=jy0922.shim@samsung.com \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=miletus@chromium.org \
--cc=rydberg@euromail.se \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).