From: nick.dyer@itdev.co.uk
To: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Yufeng Shen <miletus@google.com>,
Daniel Kurtz <djkurtz@chromium.org>,
Henrik Rydberg <rydberg@euromail.se>,
Joonyoung Shim <jy0922.shim@samsung.com>,
Alan Bowens <Alan.Bowens@atmel.com>,
linux-input@vger.kernel.org, linux-kernel@vger.kernel.org,
Peter Meerwald <pmeerw@pmeerw.net>,
Benson Leung <bleung@chromium.org>,
Olof Johansson <olofj@chromium.org>, Sekhar Nori <nsekhar@ti.com>,
Nick Dyer <nick.dyer@itdev.co.uk>
Subject: [PATCH 15/15] Input: atmel_mxt_ts - implement T44 message handling
Date: Thu, 3 Jul 2014 16:01:37 +0100 [thread overview]
Message-ID: <1404399697-26484-16-git-send-email-nick.dyer@itdev.co.uk> (raw)
In-Reply-To: <1404399697-26484-1-git-send-email-nick.dyer@itdev.co.uk>
From: Nick Dyer <nick.dyer@itdev.co.uk>
maXTouch chips allow the reading of multiple messages in a single I2C
transaction, which reduces bus overhead and improves performance/latency. The
number of messages available to be read is given by the value in the T44
object which is located directly before the T5 object.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
---
drivers/input/touchscreen/atmel_mxt_ts.c | 191 +++++++++++++++++++++++++------
1 file changed, 159 insertions(+), 32 deletions(-)
diff --git a/drivers/input/touchscreen/atmel_mxt_ts.c b/drivers/input/touchscreen/atmel_mxt_ts.c
index c3eee0f..25cfbba 100644
--- a/drivers/input/touchscreen/atmel_mxt_ts.c
+++ b/drivers/input/touchscreen/atmel_mxt_ts.c
@@ -247,6 +247,7 @@ struct mxt_data {
unsigned int max_y;
bool in_bootloader;
u16 mem_size;
+ u8 max_reportid;
u32 config_crc;
u32 info_crc;
u8 bootloader_addr;
@@ -254,6 +255,8 @@ struct mxt_data {
u8 *msg_buf;
u8 t6_status;
bool update_input;
+ u8 last_message_count;
+ u8 num_touchids;
/* Cached parameters from object table */
u16 T5_address;
@@ -264,6 +267,7 @@ struct mxt_data {
u8 T9_reportid_min;
u8 T9_reportid_max;
u8 T19_reportid;
+ u16 T44_address;
/* for fw update in bootloader */
struct completion bl_completion;
@@ -785,30 +789,142 @@ static int mxt_proc_message(struct mxt_data *data, u8 *message)
return 1;
}
-static int mxt_read_and_process_message(struct mxt_data *data)
+static int mxt_read_and_process_messages(struct mxt_data *data, u8 count)
{
struct device *dev = &data->client->dev;
int ret;
+ int i;
+ u8 num_valid = 0;
+
+ /* Safety check for msg_buf */
+ if (count > data->max_reportid)
+ return -EINVAL;
+ /* Process remaining messages if necessary */
ret = __mxt_read_reg(data->client, data->T5_address,
- data->T5_msg_size, data->msg_buf);
+ data->T5_msg_size * count, data->msg_buf);
if (ret) {
- dev_err(dev, "Error %d reading message\n", ret);
+ dev_err(dev, "Failed to read %u messages (%d)\n", count, ret);
return ret;
}
- return mxt_proc_message(data, data->msg_buf);
+ for (i = 0; i < count; i++) {
+ ret = mxt_proc_message(data,
+ data->msg_buf + data->T5_msg_size * i);
+
+ if (ret == 1)
+ num_valid++;
+ }
+
+ /* return number of messages read */
+ return num_valid;
}
-static irqreturn_t mxt_process_messages_until_invalid(struct mxt_data *data)
+static irqreturn_t mxt_process_messages_t44(struct mxt_data *data)
{
+ struct device *dev = &data->client->dev;
int ret;
+ u8 count, num_left;
- do {
- ret = mxt_read_and_process_message(data);
+ /* Read T44 and T5 together */
+ ret = __mxt_read_reg(data->client, data->T44_address,
+ data->T5_msg_size + 1, data->msg_buf);
+ if (ret) {
+ dev_err(dev, "Failed to read T44 and T5 (%d)\n", ret);
+ return IRQ_NONE;
+ }
+
+ count = data->msg_buf[0];
+
+ if (count == 0) {
+ dev_warn(dev, "Interrupt triggered but zero messages\n");
+ return IRQ_NONE;
+ } else if (count > data->max_reportid) {
+ dev_err(dev, "T44 count %d exceeded max report id\n", count);
+ count = data->max_reportid;
+ }
+
+ /* Process first message */
+ ret = mxt_proc_message(data, data->msg_buf + 1);
+ if (ret < 0) {
+ dev_warn(dev, "Unexpected invalid message\n");
+ return IRQ_NONE;
+ }
+
+ num_left = count - 1;
+
+ /* Process remaining messages if necessary */
+ if (num_left) {
+ ret = mxt_read_and_process_messages(data, num_left);
if (ret < 0)
+ goto end;
+ else if (ret != num_left)
+ dev_warn(dev, "Unexpected invalid message\n");
+ }
+
+end:
+ if (data->update_input) {
+ mxt_input_sync(data);
+ data->update_input = false;
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int mxt_process_messages_until_invalid(struct mxt_data *data)
+{
+ struct device *dev = &data->client->dev;
+ int count, read;
+ u8 tries = 2;
+
+ count = data->max_reportid;
+
+ /* Read messages until we force an invalid */
+ do {
+ read = mxt_read_and_process_messages(data, count);
+ if (read < count)
+ return 0;
+ } while (--tries);
+
+ if (data->update_input) {
+ mxt_input_sync(data);
+ data->update_input = false;
+ }
+
+ dev_err(dev, "CHG pin isn't cleared\n");
+ return -EBUSY;
+}
+
+static irqreturn_t mxt_process_messages(struct mxt_data *data)
+{
+ int total_handled, num_handled;
+ u8 count = data->last_message_count;
+
+ if (count < 1 || count > data->max_reportid)
+ count = 1;
+
+ /* include final invalid message */
+ total_handled = mxt_read_and_process_messages(data, count + 1);
+ if (total_handled < 0)
+ return IRQ_NONE;
+ /* if there were invalid messages, then we are done */
+ else if (total_handled <= count)
+ goto update_count;
+
+ /* keep reading two msgs until one is invalid or reportid limit */
+ do {
+ num_handled = mxt_read_and_process_messages(data, 2);
+ if (num_handled < 0)
return IRQ_NONE;
- } while (ret > 0);
+
+ total_handled += num_handled;
+
+ if (num_handled < 2)
+ break;
+ } while (total_handled < data->num_touchids);
+
+update_count:
+ data->last_message_count = total_handled;
if (data->update_input) {
mxt_input_sync(data);
@@ -831,7 +947,11 @@ static irqreturn_t mxt_interrupt(int irq, void *dev_id)
if (!data->object_table)
return IRQ_HANDLED;
- return mxt_process_messages_until_invalid(data);
+ if (data->T44_address) {
+ return mxt_process_messages_t44(data);
+ } else {
+ return mxt_process_messages(data);
+ }
}
static int mxt_t6_command(struct mxt_data *data, u16 cmd_offset,
@@ -1258,32 +1378,13 @@ recheck:
return 0;
}
-static int mxt_make_highchg(struct mxt_data *data)
-{
- struct device *dev = &data->client->dev;
- int count = 10;
- int ret;
-
- /* Read messages until we force an invalid */
- do {
- ret = mxt_read_and_process_message(data);
- if (ret == 0)
- return 0;
- else if (ret < 0)
- return ret;
- } while (--count);
-
- dev_err(dev, "CHG pin isn't cleared\n");
- return -EBUSY;
-}
-
static int mxt_acquire_irq(struct mxt_data *data)
{
int error;
enable_irq(data->irq);
- error = mxt_make_highchg(data);
+ error = mxt_process_messages_until_invalid(data);
if (error)
return error;
@@ -1320,6 +1421,8 @@ static void mxt_free_object_table(struct mxt_data *data)
data->T9_reportid_min = 0;
data->T9_reportid_max = 0;
data->T19_reportid = 0;
+ data->T44_address = 0;
+ data->max_reportid = 0;
}
static int mxt_get_object_table(struct mxt_data *data)
@@ -1373,8 +1476,16 @@ static int mxt_get_object_table(struct mxt_data *data)
switch (object->type) {
case MXT_GEN_MESSAGE_T5:
- /* CRC not enabled, therefore don't read last byte */
- data->T5_msg_size = mxt_obj_size(object) - 1;
+ if (data->info.family_id == 0x80) {
+ /*
+ * On mXT224 read and discard unused CRC byte
+ * otherwise DMA reads are misaligned
+ */
+ data->T5_msg_size = mxt_obj_size(object);
+ } else {
+ /* CRC not enabled, so skip last byte */
+ data->T5_msg_size = mxt_obj_size(object) - 1;
+ }
data->T5_address = object->start_address;
case MXT_GEN_COMMAND_T6:
data->T6_reportid = min_id;
@@ -1386,6 +1497,11 @@ static int mxt_get_object_table(struct mxt_data *data)
case MXT_TOUCH_MULTI_T9:
data->T9_reportid_min = min_id;
data->T9_reportid_max = max_id;
+ data->num_touchids = object->num_report_ids
+ * mxt_obj_instances(object);
+ break;
+ case MXT_SPT_MESSAGECOUNT_T44:
+ data->T44_address = object->start_address;
break;
case MXT_SPT_GPIOPWM_T19:
data->T19_reportid = min_id;
@@ -1399,7 +1515,18 @@ static int mxt_get_object_table(struct mxt_data *data)
data->mem_size = end_address + 1;
}
- data->msg_buf = kzalloc(data->T5_msg_size, GFP_KERNEL);
+ /* Store maximum reportid */
+ data->max_reportid = reportid;
+
+ /* If T44 exists, T5 position has to be directly after */
+ if (data->T44_address && (data->T5_address != data->T44_address + 1)) {
+ dev_err(&client->dev, "Invalid T44 position\n");
+ error = -EINVAL;
+ goto free_object_table;
+ }
+
+ data->msg_buf = kcalloc(data->max_reportid,
+ data->T5_msg_size, GFP_KERNEL);
if (!data->msg_buf) {
dev_err(&client->dev, "Failed to allocate message buffer\n");
error = -ENOMEM;
--
2.0.1
next prev parent reply other threads:[~2014-07-03 15:02 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-07-03 15:01 [PATCH 00/15] atmel_mxt_ts - device tree, bootloader, etc nick.dyer
2014-07-03 15:01 ` [PATCH 01/15] Input: atmel_mxt_ts - initialise IRQ before probing nick.dyer
2014-07-03 15:01 ` [PATCH 02/15] Input: atmel_mxt_ts - move input device init into separate function nick.dyer
2014-07-03 15:01 ` [PATCH 03/15] Input: atmel_mxt_ts - set pointer emulation on touchpads nick.dyer
2014-07-03 15:01 ` [PATCH 04/15] Input: atmel_mxt_ts - implement device tree support nick.dyer
2014-07-22 20:37 ` Stephen Warren
2014-07-23 15:13 ` Nick Dyer
2014-07-23 21:36 ` Stephen Warren
2014-07-24 15:10 ` Nick Dyer
2014-07-24 16:04 ` Stephen Warren
2014-07-03 15:01 ` [PATCH 05/15] Input: atmel_mxt_ts - download device config using firmware loader nick.dyer
2014-07-03 15:01 ` [PATCH 06/15] Input: atmel_mxt_ts - calculate and check CRC in config file nick.dyer
2014-07-03 15:01 ` [PATCH 07/15] Input: atmel_mxt_ts - use deep sleep mode when stopped nick.dyer
2014-07-03 15:01 ` [PATCH 08/15] Input: atmel_mxt_ts - handle APP_CRC_FAIL on startup nick.dyer
2014-07-03 15:01 ` [PATCH 09/15] Input: atmel_mxt_ts - handle bootloader previously unlocked nick.dyer
2014-07-03 15:01 ` [PATCH 10/15] Input: atmel_mxt_ts - add bootloader addresses for new chips nick.dyer
2014-07-03 15:01 ` [PATCH 11/15] Input: atmel_mxt_ts - recover from bootloader on probe nick.dyer
2014-07-03 15:01 ` [PATCH 12/15] Input: atmel_mxt_ts - add support for dynamic message size nick.dyer
2014-07-03 15:01 ` [PATCH 13/15] Input: atmel_mxt_ts - decode T6 status messages nick.dyer
2014-07-03 15:01 ` [PATCH 14/15] Input: atmel_mxt_ts - split message handler into separate functions nick.dyer
2014-07-03 15:01 ` nick.dyer [this message]
2014-07-07 11:21 ` [PATCH 00/15] atmel_mxt_ts - device tree, bootloader, etc Sekhar Nori
2014-07-07 11:38 ` Nick Dyer
2014-07-08 12:28 ` Sekhar Nori
2014-07-22 20:34 ` Stephen Warren
2014-07-23 15:30 ` Nick Dyer
2014-07-23 17:22 ` Stephen Warren
2014-07-23 20:29 ` Dmitry Torokhov
2014-07-23 21:39 ` Stephen Warren
2014-07-24 13:47 ` Nick Dyer
2014-07-24 21:19 ` Stephen Warren
2014-07-25 14:10 ` Nick Dyer
2014-07-25 20:06 ` Stephen Warren
2014-07-28 17:28 ` Dmitry Torokhov
2014-07-28 20:20 ` Yufeng Shen
2014-07-28 21:23 ` Stephen Warren
2014-07-28 23:42 ` Stephen Warren
2014-07-29 0:10 ` Yufeng Shen
2014-07-29 16:16 ` Stephen Warren
2014-07-29 17:06 ` Nick Dyer
2014-07-29 19:26 ` Stephen Warren
2014-09-02 15:45 ` Stephen Warren
2014-07-29 16:43 ` Nick Dyer
2014-07-29 16:26 ` Nick Dyer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1404399697-26484-16-git-send-email-nick.dyer@itdev.co.uk \
--to=nick.dyer@itdev.co.uk \
--cc=Alan.Bowens@atmel.com \
--cc=bleung@chromium.org \
--cc=djkurtz@chromium.org \
--cc=dmitry.torokhov@gmail.com \
--cc=jy0922.shim@samsung.com \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=miletus@google.com \
--cc=nsekhar@ti.com \
--cc=olofj@chromium.org \
--cc=pmeerw@pmeerw.net \
--cc=rydberg@euromail.se \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).