[PATCH] HID: rmi: Write updated F11 control registers after reset

[Andrew Duggan <aduggan@synaptics.com>]

When a device is reset the values of control registers will be reset to
the defaults. This patch reapplies the control register values set for F11
by the driver.

Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
---
 drivers/hid/hid-rmi.c | 41 ++++++++++++++++++++++++++++++++++-------
 1 file changed, 34 insertions(+), 7 deletions(-)

diff --git a/drivers/hid/hid-rmi.c b/drivers/hid/hid-rmi.c
index af191a2..80c068f 100644
--- a/drivers/hid/hid-rmi.c
+++ b/drivers/hid/hid-rmi.c
@@ -40,6 +40,8 @@
 #define RMI_DEVICE			BIT(0)
 #define RMI_DEVICE_HAS_PHYS_BUTTONS	BIT(1)
 
+#define RMI_F11_CTRL_REG_COUNT		12
+
 enum rmi_mode_type {
 	RMI_MODE_OFF			= 0,
 	RMI_MODE_ATTN_REPORTS		= 1,
@@ -116,6 +118,8 @@ struct rmi_data {
 	unsigned int max_y;
 	unsigned int x_size_mm;
 	unsigned int y_size_mm;
+	bool read_f11_ctrl_regs;
+	u8 f11_ctrl_regs[RMI_F11_CTRL_REG_COUNT];
 
 	unsigned int gpio_led_count;
 	unsigned int button_count;
@@ -557,6 +561,15 @@ static int rmi_set_sleep_mode(struct hid_device *hdev, int sleep_mode)
 
 static int rmi_suspend(struct hid_device *hdev, pm_message_t message)
 {
+	struct rmi_data *data = hid_get_drvdata(hdev);
+	int ret;
+
+	ret = rmi_read_block(hdev, data->f11.control_base_addr,
+			data->f11_ctrl_regs, RMI_F11_CTRL_REG_COUNT);
+	if (ret)
+		hid_warn(hdev, "can not read F11 control registers\n");
+
+
 	if (!device_may_wakeup(hdev->dev.parent))
 		return rmi_set_sleep_mode(hdev, RMI_SLEEP_DEEP_SLEEP);
 
@@ -565,6 +578,7 @@ static int rmi_suspend(struct hid_device *hdev, pm_message_t message)
 
 static int rmi_post_reset(struct hid_device *hdev)
 {
+	struct rmi_data *data = hid_get_drvdata(hdev);
 	int ret;
 
 	ret = rmi_set_mode(hdev, RMI_MODE_ATTN_REPORTS);
@@ -573,6 +587,14 @@ static int rmi_post_reset(struct hid_device *hdev)
 		return ret;
 	}
 
+	if (data->read_f11_ctrl_regs) {
+		ret = rmi_write_block(hdev, data->f11.control_base_addr,
+				data->f11_ctrl_regs, RMI_F11_CTRL_REG_COUNT);
+		if (ret)
+			hid_warn(hdev,
+				"can not write F11 control registers after reset\n");
+	}
+
 	if (!device_may_wakeup(hdev->dev.parent)) {
 		ret = rmi_set_sleep_mode(hdev, RMI_SLEEP_NORMAL);
 		if (ret) {
@@ -963,18 +985,23 @@ static int rmi_populate_f11(struct hid_device *hdev)
 	 * and there is no way to know if the first 20 bytes are here or not.
 	 * We use only the first 12 bytes, so get only them.
 	 */
-	ret = rmi_read_block(hdev, data->f11.control_base_addr, buf, 12);
+	ret = rmi_read_block(hdev, data->f11.control_base_addr,
+			data->f11_ctrl_regs, RMI_F11_CTRL_REG_COUNT);
 	if (ret) {
 		hid_err(hdev, "can not read ctrl block of size 11: %d.\n", ret);
 		return ret;
 	}
 
-	data->max_x = buf[6] | (buf[7] << 8);
-	data->max_y = buf[8] | (buf[9] << 8);
+	/* data->f11_ctrl_regs now contains valid register data */
+	data->read_f11_ctrl_regs = true;
+
+	data->max_x = data->f11_ctrl_regs[6] | (data->f11_ctrl_regs[7] << 8);
+	data->max_y = data->f11_ctrl_regs[8] | (data->f11_ctrl_regs[9] << 8);
 
 	if (has_dribble) {
-		buf[0] = buf[0] & ~BIT(6);
-		ret = rmi_write(hdev, data->f11.control_base_addr, buf);
+		data->f11_ctrl_regs[0] = data->f11_ctrl_regs[0] & ~BIT(6);
+		ret = rmi_write(hdev, data->f11.control_base_addr,
+				data->f11_ctrl_regs);
 		if (ret) {
 			hid_err(hdev, "can not write to control reg 0: %d.\n",
 				ret);
@@ -983,9 +1010,9 @@ static int rmi_populate_f11(struct hid_device *hdev)
 	}
 
 	if (has_palm_detect) {
-		buf[11] = buf[11] & ~BIT(0);
+		data->f11_ctrl_regs[11] = data->f11_ctrl_regs[11] & ~BIT(0);
 		ret = rmi_write(hdev, data->f11.control_base_addr + 11,
-				&buf[11]);
+				&data->f11_ctrl_regs[11]);
 		if (ret) {
 			hid_err(hdev, "can not write to control reg 11: %d.\n",
 				ret);
-- 
2.1.4