* [PATCH 12/41] Documentation: dt: input: fix spelling mistakes
[not found] <1461543878-3639-1-git-send-email-eric@engestrom.ch>
@ 2016-04-25 0:24 ` Eric Engestrom
2016-04-25 13:49 ` Rob Herring
0 siblings, 1 reply; 2+ messages in thread
From: Eric Engestrom @ 2016-04-25 0:24 UTC (permalink / raw)
To: linux-kernel
Cc: Eric Engestrom, Dmitry Torokhov, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala, Markus Pargmann,
Lee Jones, linux-input, devicetree
Signed-off-by: Eric Engestrom <eric@engestrom.ch>
---
Documentation/devicetree/bindings/input/ads7846.txt | 2 +-
Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt
index c6cfe2e..9fc47b0 100644
--- a/Documentation/devicetree/bindings/input/ads7846.txt
+++ b/Documentation/devicetree/bindings/input/ads7846.txt
@@ -29,7 +29,7 @@ Optional properties:
ti,vref-delay-usecs vref supply delay in usecs, 0 for
external vref (u16).
ti,vref-mv The VREF voltage, in millivolts (u16).
- Set to 0 to use internal refernce
+ Set to 0 to use internal references
(ADS7846).
ti,keep-vref-on set to keep vref on for differential
measurements as well
diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
index cdf05f9..abfcab3 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
@@ -15,7 +15,7 @@ Optional properties:
- fsl,pen-debounce-ns: Pen debounce time in nanoseconds.
- fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value
between 1 and 4096. It is the ratio between the internal reference voltage
- and the measured voltage after the plate was precharged. Resistence between
+ and the measured voltage after the plate was precharged. Resistance between
plates and therefore the voltage decreases with pressure so that a smaller
value is equivalent to a higher pressure.
- fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before
--
2.8.0
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH 12/41] Documentation: dt: input: fix spelling mistakes
2016-04-25 0:24 ` [PATCH 12/41] Documentation: dt: input: fix spelling mistakes Eric Engestrom
@ 2016-04-25 13:49 ` Rob Herring
0 siblings, 0 replies; 2+ messages in thread
From: Rob Herring @ 2016-04-25 13:49 UTC (permalink / raw)
To: Eric Engestrom
Cc: linux-kernel, Dmitry Torokhov, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Markus Pargmann, Lee Jones, linux-input,
devicetree
On Mon, Apr 25, 2016 at 01:24:09AM +0100, Eric Engestrom wrote:
> Signed-off-by: Eric Engestrom <eric@engestrom.ch>
Applied, thanks.
Rob
> ---
> Documentation/devicetree/bindings/input/ads7846.txt | 2 +-
> Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt | 2 +-
> 2 files changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt
> index c6cfe2e..9fc47b0 100644
> --- a/Documentation/devicetree/bindings/input/ads7846.txt
> +++ b/Documentation/devicetree/bindings/input/ads7846.txt
> @@ -29,7 +29,7 @@ Optional properties:
> ti,vref-delay-usecs vref supply delay in usecs, 0 for
> external vref (u16).
> ti,vref-mv The VREF voltage, in millivolts (u16).
> - Set to 0 to use internal refernce
> + Set to 0 to use internal references
> (ADS7846).
> ti,keep-vref-on set to keep vref on for differential
> measurements as well
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
> index cdf05f9..abfcab3 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
> @@ -15,7 +15,7 @@ Optional properties:
> - fsl,pen-debounce-ns: Pen debounce time in nanoseconds.
> - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value
> between 1 and 4096. It is the ratio between the internal reference voltage
> - and the measured voltage after the plate was precharged. Resistence between
> + and the measured voltage after the plate was precharged. Resistance between
> plates and therefore the voltage decreases with pressure so that a smaller
> value is equivalent to a higher pressure.
> - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before
> --
> 2.8.0
>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2016-04-25 13:49 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1461543878-3639-1-git-send-email-eric@engestrom.ch>
2016-04-25 0:24 ` [PATCH 12/41] Documentation: dt: input: fix spelling mistakes Eric Engestrom
2016-04-25 13:49 ` Rob Herring
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).