Re: [PATCH] hid Logitech G13 Driver 0.0.5

[Marek Vasut <marek.vasut@gmail.com>]

Dne St 3. března 2010 06:13:12 Pavel Machek napsal(a):
> Hi!
> 
> > >> +/*
> > >> + * This is a default logo to be loaded upon driver initialization
> > >> + * replacing the default Logitech G13 image loaded on device
> > >> + * initialization. This is to provide the user a cue that the
> > >> + * Linux driver is loaded and ready.
> > >> + *
> > >> + * This logo contains the text G13 in the center with two penguins
> > >> + * on each side of the text. The penguins are a 33x40 rendition of
> > >> + * the default framebuffer 80x80 monochrome image scaled down and
> > >> + * cleaned up to retain something that looks a little better than
> > >> + * a simple scaling.
> > >> + *
> > >> + * This logo is a simple xbm image created in GIMP and exported.
> > >> + * To view the image copy the following two #defines plus the
> > >> + * g13_lcd_bits to an ASCII text file and save with extension
> > >> + * .xbm, then open with GIMP or any other graphical editor
> > >> + * such as eog that recognizes the .xbm format.
> > >> + */
> > > 
> > > ...
> > > 
> > >> +static unsigned char g13_lcd_bits[] = {
> > >> + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > >> 0x00,
> > > 
> > > I think you'll agree above is not an elegant solution.
> > 
> > I could make it a config option.
> 
> You get about 10 complains already, but you are not willing to solve
> it. No, config option does not help.
> 
> If you want to, make it separate patch so we can reject it separately.
> 
> > >> +static DEVICE_ATTR(rgb, 0666, g13_rgb_show, g13_rgb_store);
> > > 
> > > Reading above code, it looks like this new userspace sysfs attribute
> > > is for backlight control. Could that be better exposed using the
> > > existing backlight class?
> > 
> > I looked at the backlight class and it didn't seem to be a very good fit.
> > 
> > /* This structure defines all the properties of a backlight */
> > struct backlight_properties {
> > 
> > 	/* Current User requested brightness (0 - max_brightness) */
> > 	int brightness;
> > 	/* Maximal value for brightness (read-only) */
> > 	int max_brightness;
> > 	/* Current FB Power mode (0: full on, 1..3: power saving
> > 	
> > 	   modes; 4: full off), see FB_BLANK_XXX */
> > 	
> > 	int power;
> > 	/* FB Blanking active? (values as for power) */
> > 	/* Due to be removed, please use (state & BL_CORE_FBBLANK) */
> > 	int fb_blank;
> > 	/* Flags used to signal drivers of state changes */
> > 	/* Upper 4 bits are reserved for driver internal use */
> > 	unsigned int state;
> > 
> > };
> > 
> > The g13's backlight doesn't support any of these properties. All you can
> > set is an rgb value on the g13; no power modes, no brightness, etc. I
> > could add a brightness attribute by scaling the rgb values, but I would
> > prefer to do that from userspace rather than the driver since it's not
> > supported in the device itself.
> > 
> > And, we'd still have to have the rgb attribute since the backlight class
> > doesn't have color.
> 
> Or you could pretend you have 3 different backlights? ....which is
> actually what you have...?
> 									Pavel

Any updates on this?

btw. it'd be good if we could use the g13fb on G15 ... would that be possible?
Cheers!