* [PATCH v2] atkbd: Fix multi-char scancode handling on reconnect.
@ 2012-12-21 2:33 Shawn Nematbakhsh
2013-01-06 9:10 ` Dmitry Torokhov
0 siblings, 1 reply; 3+ messages in thread
From: Shawn Nematbakhsh @ 2012-12-21 2:33 UTC (permalink / raw)
To: dmitry.torokhov; +Cc: shawnn, jj, linux-input, linux-kernel
On resume from suspend there is a possibility for multi-byte scancodes
to be handled incorrectly. atkbd_reconnect disables the processing of
scancodes in software by calling atkbd_disable, but the keyboard may
still be active because no disconnect command was sent. Later, software
handling is re-enabled. If a multi-byte scancode sent from the keyboard
straddles the re-enable, only the latter byte(s) will be handled.
In practice, this leads to cases where multi-byte break codes (ex. "e0
4d" - break code for right-arrow) are misread as make codes ("4d" - make
code for numeric 6), leading to one or more unwanted, untyped characters
being interpreted.
The solution implemented here involves sending command f5 (reset
disable) to the keyboard prior to disabling software handling of codes.
Later, the command to re-enable the keyboard is sent only after we are
prepared to handle scancodes.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
---
Changes since v1:
- Removed unused return values from atkbd_deactivate.
drivers/input/keyboard/atkbd.c | 22 ++++++++++++++++++++--
1 files changed, 20 insertions(+), 2 deletions(-)
diff --git a/drivers/input/keyboard/atkbd.c b/drivers/input/keyboard/atkbd.c
index add5ffd..44dcf83 100644
--- a/drivers/input/keyboard/atkbd.c
+++ b/drivers/input/keyboard/atkbd.c
@@ -844,6 +844,20 @@ static int atkbd_activate(struct atkbd *atkbd)
}
/*
+ * atkbd_deactivate() resets and disables the keyboard from sending
+ * keystrokes.
+ */
+static void atkbd_deactivate(struct atkbd *atkbd)
+{
+ struct ps2dev *ps2dev = &atkbd->ps2dev;
+
+ if (ps2_command(ps2dev, NULL, ATKBD_CMD_RESET_DIS))
+ dev_err(&ps2dev->serio->dev,
+ "Failed to deactivate keyboard on %s\n",
+ ps2dev->serio->phys);
+}
+
+/*
* atkbd_cleanup() restores the keyboard state so that BIOS is happy after a
* reboot.
*/
@@ -1199,6 +1213,9 @@ static int atkbd_reconnect(struct serio *serio)
mutex_lock(&atkbd->mutex);
+ if (atkbd->write)
+ atkbd_deactivate(atkbd);
+
atkbd_disable(atkbd);
if (atkbd->write) {
@@ -1208,8 +1225,6 @@ static int atkbd_reconnect(struct serio *serio)
if (atkbd->set != atkbd_select_set(atkbd, atkbd->set, atkbd->extra))
goto out;
- atkbd_activate(atkbd);
-
/*
* Restore LED state and repeat rate. While input core
* will do this for us at resume time reconnect may happen
@@ -1224,6 +1239,9 @@ static int atkbd_reconnect(struct serio *serio)
}
atkbd_enable(atkbd);
+ if (atkbd->write)
+ atkbd_activate(atkbd);
+
retval = 0;
out:
--
1.7.7.3
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v2] atkbd: Fix multi-char scancode handling on reconnect.
2012-12-21 2:33 [PATCH v2] atkbd: Fix multi-char scancode handling on reconnect Shawn Nematbakhsh
@ 2013-01-06 9:10 ` Dmitry Torokhov
2013-01-10 22:23 ` Shawn Nematbakhsh
0 siblings, 1 reply; 3+ messages in thread
From: Dmitry Torokhov @ 2013-01-06 9:10 UTC (permalink / raw)
To: Shawn Nematbakhsh; +Cc: jj, linux-input, linux-kernel
Hi Shawn,
On Thu, Dec 20, 2012 at 06:33:11PM -0800, Shawn Nematbakhsh wrote:
> On resume from suspend there is a possibility for multi-byte scancodes
> to be handled incorrectly. atkbd_reconnect disables the processing of
> scancodes in software by calling atkbd_disable, but the keyboard may
> still be active because no disconnect command was sent. Later, software
> handling is re-enabled. If a multi-byte scancode sent from the keyboard
> straddles the re-enable, only the latter byte(s) will be handled.
>
> In practice, this leads to cases where multi-byte break codes (ex. "e0
> 4d" - break code for right-arrow) are misread as make codes ("4d" - make
> code for numeric 6), leading to one or more unwanted, untyped characters
> being interpreted.
>
> The solution implemented here involves sending command f5 (reset
> disable) to the keyboard prior to disabling software handling of codes.
> Later, the command to re-enable the keyboard is sent only after we are
> prepared to handle scancodes.
The core tries to avoid disturbing devices that are not keyboards, so I
believe we should check the device ID first and if it is keyboard, then
do the reset. We should also reset the internal state (emul and xl_bit)
when re-enabling the device.
Does the version of the patch below work for you?
Thanks.
--
Dmitry
Input: atkbd - fix multi-byte scancode handling on reconnect
From: Shawn Nematbakhsh <shawnn@chromium.org>
On resume from suspend there is a possibility for multi-byte scancodes
to be handled incorrectly. atkbd_reconnect disables the processing of
scancodes in software by calling atkbd_disable, but the keyboard may
still be active because no disconnect command was sent. Later, software
handling is re-enabled. If a multi-byte scancode sent from the keyboard
straddles the re-enable, only the latter byte(s) will be handled.
In practice, this leads to cases where multi-byte break codes (ex. "e0
4d" - break code for right-arrow) are misread as make codes ("4d" - make
code for numeric 6), leading to one or more unwanted, untyped characters
being interpreted.
The solution implemented here involves sending command f5 (reset
disable) to the keyboard prior to disabling software handling of codes.
Later, the command to re-enable the keyboard is sent only after we are
prepared to handle scancodes.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
---
drivers/input/keyboard/atkbd.c | 72 ++++++++++++++++++++++++++++------------
1 file changed, 51 insertions(+), 21 deletions(-)
diff --git a/drivers/input/keyboard/atkbd.c b/drivers/input/keyboard/atkbd.c
index 33d0fcd..2626773 100644
--- a/drivers/input/keyboard/atkbd.c
+++ b/drivers/input/keyboard/atkbd.c
@@ -676,6 +676,39 @@ static inline void atkbd_disable(struct atkbd *atkbd)
serio_continue_rx(atkbd->ps2dev.serio);
}
+static int atkbd_activate(struct atkbd *atkbd)
+{
+ struct ps2dev *ps2dev = &atkbd->ps2dev;
+
+/*
+ * Enable the keyboard to receive keystrokes.
+ */
+
+ if (ps2_command(ps2dev, NULL, ATKBD_CMD_ENABLE)) {
+ dev_err(&ps2dev->serio->dev,
+ "Failed to enable keyboard on %s\n",
+ ps2dev->serio->phys);
+ return -1;
+ }
+
+ return 0;
+}
+
+/*
+ * atkbd_deactivate() resets and disables the keyboard from sending
+ * keystrokes.
+ */
+
+static void atkbd_deactivate(struct atkbd *atkbd)
+{
+ struct ps2dev *ps2dev = &atkbd->ps2dev;
+
+ if (ps2_command(ps2dev, NULL, ATKBD_CMD_RESET_DIS))
+ dev_err(&ps2dev->serio->dev,
+ "Failed to deactivate keyboard on %s\n",
+ ps2dev->serio->phys);
+}
+
/*
* atkbd_probe() probes for an AT keyboard on a serio port.
*/
@@ -731,6 +764,12 @@ static int atkbd_probe(struct atkbd *atkbd)
return -1;
}
+/*
+ * Make sure nothing is coming from the keyboard and disturbs our
+ * internal state.
+ */
+ atkbd_deactivate(atkbd);
+
return 0;
}
@@ -825,24 +864,6 @@ static int atkbd_reset_state(struct atkbd *atkbd)
return 0;
}
-static int atkbd_activate(struct atkbd *atkbd)
-{
- struct ps2dev *ps2dev = &atkbd->ps2dev;
-
-/*
- * Enable the keyboard to receive keystrokes.
- */
-
- if (ps2_command(ps2dev, NULL, ATKBD_CMD_ENABLE)) {
- dev_err(&ps2dev->serio->dev,
- "Failed to enable keyboard on %s\n",
- ps2dev->serio->phys);
- return -1;
- }
-
- return 0;
-}
-
/*
* atkbd_cleanup() restores the keyboard state so that BIOS is happy after a
* reboot.
@@ -1150,7 +1171,6 @@ static int atkbd_connect(struct serio *serio, struct serio_driver *drv)
atkbd->set = atkbd_select_set(atkbd, atkbd_set, atkbd_extra);
atkbd_reset_state(atkbd);
- atkbd_activate(atkbd);
} else {
atkbd->set = 2;
@@ -1165,6 +1185,8 @@ static int atkbd_connect(struct serio *serio, struct serio_driver *drv)
goto fail3;
atkbd_enable(atkbd);
+ if (serio->write)
+ atkbd_activate(atkbd);
err = input_register_device(atkbd->dev);
if (err)
@@ -1208,8 +1230,6 @@ static int atkbd_reconnect(struct serio *serio)
if (atkbd->set != atkbd_select_set(atkbd, atkbd->set, atkbd->extra))
goto out;
- atkbd_activate(atkbd);
-
/*
* Restore LED state and repeat rate. While input core
* will do this for us at resume time reconnect may happen
@@ -1223,7 +1243,17 @@ static int atkbd_reconnect(struct serio *serio)
}
+ /*
+ * Reset our state machine in case reconnect happened in the middle
+ * of multi-byte scancode.
+ */
+ atkbd->xl_bit = 0;
+ atkbd->emul = 0;
+
atkbd_enable(atkbd);
+ if (atkbd->write)
+ atkbd_activate(atkbd);
+
retval = 0;
out:
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v2] atkbd: Fix multi-char scancode handling on reconnect.
2013-01-06 9:10 ` Dmitry Torokhov
@ 2013-01-10 22:23 ` Shawn Nematbakhsh
0 siblings, 0 replies; 3+ messages in thread
From: Shawn Nematbakhsh @ 2013-01-10 22:23 UTC (permalink / raw)
To: Dmitry Torokhov; +Cc: jj, linux-input, linux-kernel
Hi Dmitry,
On Sun, Jan 6, 2013 at 1:10 AM, Dmitry Torokhov
<dmitry.torokhov@gmail.com> wrote:
> Hi Shawn,
>
> On Thu, Dec 20, 2012 at 06:33:11PM -0800, Shawn Nematbakhsh wrote:
>> On resume from suspend there is a possibility for multi-byte scancodes
>> to be handled incorrectly. atkbd_reconnect disables the processing of
>> scancodes in software by calling atkbd_disable, but the keyboard may
>> still be active because no disconnect command was sent. Later, software
>> handling is re-enabled. If a multi-byte scancode sent from the keyboard
>> straddles the re-enable, only the latter byte(s) will be handled.
>>
>> In practice, this leads to cases where multi-byte break codes (ex. "e0
>> 4d" - break code for right-arrow) are misread as make codes ("4d" - make
>> code for numeric 6), leading to one or more unwanted, untyped characters
>> being interpreted.
>>
>> The solution implemented here involves sending command f5 (reset
>> disable) to the keyboard prior to disabling software handling of codes.
>> Later, the command to re-enable the keyboard is sent only after we are
>> prepared to handle scancodes.
>
> The core tries to avoid disturbing devices that are not keyboards, so I
> believe we should check the device ID first and if it is keyboard, then
> do the reset. We should also reset the internal state (emul and xl_bit)
> when re-enabling the device.
>
> Does the version of the patch below work for you?
>
> Thanks.
>
> --
> Dmitry
Thanks for the revision. This version of the patch tests good. I agree
with your changes, it makes sense to deactivate the keyboard from both
connect and reconnect, just in case the keyboard is able to send
scancodes at this point.
--
Shawn
>
> Input: atkbd - fix multi-byte scancode handling on reconnect
>
> From: Shawn Nematbakhsh <shawnn@chromium.org>
>
> On resume from suspend there is a possibility for multi-byte scancodes
> to be handled incorrectly. atkbd_reconnect disables the processing of
> scancodes in software by calling atkbd_disable, but the keyboard may
> still be active because no disconnect command was sent. Later, software
> handling is re-enabled. If a multi-byte scancode sent from the keyboard
> straddles the re-enable, only the latter byte(s) will be handled.
>
> In practice, this leads to cases where multi-byte break codes (ex. "e0
> 4d" - break code for right-arrow) are misread as make codes ("4d" - make
> code for numeric 6), leading to one or more unwanted, untyped characters
> being interpreted.
>
> The solution implemented here involves sending command f5 (reset
> disable) to the keyboard prior to disabling software handling of codes.
> Later, the command to re-enable the keyboard is sent only after we are
> prepared to handle scancodes.
>
> Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
> ---
> drivers/input/keyboard/atkbd.c | 72 ++++++++++++++++++++++++++++------------
> 1 file changed, 51 insertions(+), 21 deletions(-)
>
> diff --git a/drivers/input/keyboard/atkbd.c b/drivers/input/keyboard/atkbd.c
> index 33d0fcd..2626773 100644
> --- a/drivers/input/keyboard/atkbd.c
> +++ b/drivers/input/keyboard/atkbd.c
> @@ -676,6 +676,39 @@ static inline void atkbd_disable(struct atkbd *atkbd)
> serio_continue_rx(atkbd->ps2dev.serio);
> }
>
> +static int atkbd_activate(struct atkbd *atkbd)
> +{
> + struct ps2dev *ps2dev = &atkbd->ps2dev;
> +
> +/*
> + * Enable the keyboard to receive keystrokes.
> + */
> +
> + if (ps2_command(ps2dev, NULL, ATKBD_CMD_ENABLE)) {
> + dev_err(&ps2dev->serio->dev,
> + "Failed to enable keyboard on %s\n",
> + ps2dev->serio->phys);
> + return -1;
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * atkbd_deactivate() resets and disables the keyboard from sending
> + * keystrokes.
> + */
> +
> +static void atkbd_deactivate(struct atkbd *atkbd)
> +{
> + struct ps2dev *ps2dev = &atkbd->ps2dev;
> +
> + if (ps2_command(ps2dev, NULL, ATKBD_CMD_RESET_DIS))
> + dev_err(&ps2dev->serio->dev,
> + "Failed to deactivate keyboard on %s\n",
> + ps2dev->serio->phys);
> +}
> +
> /*
> * atkbd_probe() probes for an AT keyboard on a serio port.
> */
> @@ -731,6 +764,12 @@ static int atkbd_probe(struct atkbd *atkbd)
> return -1;
> }
>
> +/*
> + * Make sure nothing is coming from the keyboard and disturbs our
> + * internal state.
> + */
> + atkbd_deactivate(atkbd);
> +
> return 0;
> }
>
> @@ -825,24 +864,6 @@ static int atkbd_reset_state(struct atkbd *atkbd)
> return 0;
> }
>
> -static int atkbd_activate(struct atkbd *atkbd)
> -{
> - struct ps2dev *ps2dev = &atkbd->ps2dev;
> -
> -/*
> - * Enable the keyboard to receive keystrokes.
> - */
> -
> - if (ps2_command(ps2dev, NULL, ATKBD_CMD_ENABLE)) {
> - dev_err(&ps2dev->serio->dev,
> - "Failed to enable keyboard on %s\n",
> - ps2dev->serio->phys);
> - return -1;
> - }
> -
> - return 0;
> -}
> -
> /*
> * atkbd_cleanup() restores the keyboard state so that BIOS is happy after a
> * reboot.
> @@ -1150,7 +1171,6 @@ static int atkbd_connect(struct serio *serio, struct serio_driver *drv)
>
> atkbd->set = atkbd_select_set(atkbd, atkbd_set, atkbd_extra);
> atkbd_reset_state(atkbd);
> - atkbd_activate(atkbd);
>
> } else {
> atkbd->set = 2;
> @@ -1165,6 +1185,8 @@ static int atkbd_connect(struct serio *serio, struct serio_driver *drv)
> goto fail3;
>
> atkbd_enable(atkbd);
> + if (serio->write)
> + atkbd_activate(atkbd);
>
> err = input_register_device(atkbd->dev);
> if (err)
> @@ -1208,8 +1230,6 @@ static int atkbd_reconnect(struct serio *serio)
> if (atkbd->set != atkbd_select_set(atkbd, atkbd->set, atkbd->extra))
> goto out;
>
> - atkbd_activate(atkbd);
> -
> /*
> * Restore LED state and repeat rate. While input core
> * will do this for us at resume time reconnect may happen
> @@ -1223,7 +1243,17 @@ static int atkbd_reconnect(struct serio *serio)
>
> }
>
> + /*
> + * Reset our state machine in case reconnect happened in the middle
> + * of multi-byte scancode.
> + */
> + atkbd->xl_bit = 0;
> + atkbd->emul = 0;
> +
> atkbd_enable(atkbd);
> + if (atkbd->write)
> + atkbd_activate(atkbd);
> +
> retval = 0;
>
> out:
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2013-01-10 22:23 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-12-21 2:33 [PATCH v2] atkbd: Fix multi-char scancode handling on reconnect Shawn Nematbakhsh
2013-01-06 9:10 ` Dmitry Torokhov
2013-01-10 22:23 ` Shawn Nematbakhsh
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).