From mboxrd@z Thu Jan 1 00:00:00 1970 From: Michael Welling Subject: Re: [PATCH 4/4] Input: tsc2004 - Document ts2004 dt bindings Date: Tue, 3 Nov 2015 09:41:17 -0600 Message-ID: <20151103154117.GA13271@deathstar> References: <1446252086-24334-1-git-send-email-mwelling@ieee.org> <1446252086-24334-5-git-send-email-mwelling@ieee.org> <20151102205028.GA2571@deathstar> <20151103072124.GA33601@dtor-ws> Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Return-path: Content-Disposition: inline In-Reply-To: Sender: linux-kernel-owner@vger.kernel.org To: Rob Herring Cc: Dmitry Torokhov , kbuild test robot , kbuild-all@01.org, Tony Lindgren , Pavel Machek , Felipe Balbi , Sebastian Reichel , Roger Quadros , Arnd Bergmann , Mark Brown , "devicetree@vger.kernel.org" , "linux-kernel@vger.kernel.org" , "linux-input@vger.kernel.org" List-Id: linux-input@vger.kernel.org On Tue, Nov 03, 2015 at 09:31:10AM -0600, Rob Herring wrote: > On Tue, Nov 3, 2015 at 1:21 AM, Dmitry Torokhov > wrote: > > On Mon, Nov 02, 2015 at 02:50:29PM -0600, Michael Welling wrote: > >> On Mon, Nov 02, 2015 at 09:19:50AM -0600, Rob Herring wrote: > >> > > +Required properties: > >> > > + - compatible : "ti,tsc2004" > >> > > + - interrupts : IRQ specifier > >> > > + - vio-supply : Regulator specifier > >> > > >> > reg property? > >> > >> Rob, > >> > >> It appears that I missed this in the description. > >> > >> Probably because I was following the lead of the ts2005 description. > >> > >> How does this look: > >> - reg : I2C address. 0x48 - 0x4b based on the voltage applied to > >> the AD1 and AD0 inputs on the IC. > >> > > > > How about the version below? > > > > Thanks. > > > > -- > > Dmitry > > > > > > Input: tsc2004 - document ts2004 dt bindings Just noticed that it says ts2004 instead of tsc2004 in the subject. Otherwise, I am fine with it. Thanks for the assistance. Still no acks or reviews for the other patches in the series. I would like for someone to test the tsc2005 support to see if it still works. The tsc2004 works very well on the target that I have here. > > > > From: Michael Welling > > > > Adds documentation for the devicetree bindings of the new tsc2004 driver. > > > > Signed-off-by: Michael Welling > > Signed-off-by: Dmitry Torokhov > > Acked-by: Rob Herring > > > --- > > .../bindings/input/touchscreen/tsc2005.txt | 34 ++++++++++++++++---- > > 1 file changed, 28 insertions(+), 6 deletions(-) > > > > diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt > > index 09089a6..b80c04b 100644 > > --- a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt > > +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt > > @@ -1,14 +1,15 @@ > > -* Texas Instruments tsc2005 touchscreen controller > > +* Texas Instruments tsc2004 and tsc2005 touchscreen controllers > > > > Required properties: > > - - compatible : "ti,tsc2005" > > - - reg : SPI device address > > - - spi-max-frequency : Maximal SPI speed > > + - compatible : "ti,tsc2004" or "ti,tsc2005" > > + - reg : Device address > > - interrupts : IRQ specifier > > - - reset-gpios : GPIO specifier > > - - vio-supply : Regulator specifier > > + - spi-max-frequency : Maximum SPI clocking speed of the device > > + (for tsc2005) > > > > Optional properties: > > + - vio-supply : Regulator specifier > > + - reset-gpios : GPIO specifier for the controller reset line > > - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates > > in ohm (defaults to 280) > > - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after > > @@ -18,6 +19,27 @@ Optional properties: > > > > Example: > > > > +&i2c3 { > > + tsc2004@48 { > > + compatible = "ti,tsc2004"; > > + reg = <0x48>; > > + vio-supply = <&vio>; > > + > > + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; > > + interrupts-extended = <&gpio1 27 IRQ_TYPE_EDGE_RISING>; > > + > > + touchscreen-fuzz-x = <4>; > > + touchscreen-fuzz-y = <7>; > > + touchscreen-fuzz-pressure = <2>; > > + touchscreen-size-x = <4096>; > > + touchscreen-size-y = <4096>; > > + touchscreen-max-pressure = <2048>; > > + > > + ti,x-plate-ohms = <280>; > > + ti,esd-recovery-timeout-ms = <8000>; > > + }; > > +} > > + > > &mcspi1 { > > tsc2005@0 { > > compatible = "ti,tsc2005";