From: Dmitry Torokhov <dmitry.torokhov-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
To: Marcin Niestroj <m.niestroj-z3quKL4iOrmQ6ZAhV5LmOA@public.gmane.org>
Cc: Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>,
Bastien Nocera <hadess-0MeiytkfxGOsTnJN9+BGXg@public.gmane.org>,
Antonio Ospite <ao2-qKGr9MkilAE@public.gmane.org>,
linux-input-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: Re: [PATCH v2] Input: goodix - support gt1151 touchpanel
Date: Tue, 24 Oct 2017 11:07:40 -0700 [thread overview]
Message-ID: <20171024180740.ozcyvsk5zji3hpcn@dtor-ws> (raw)
In-Reply-To: <20171024091305.16411-1-m.niestroj-z3quKL4iOrmQ6ZAhV5LmOA@public.gmane.org>
On Tue, Oct 24, 2017 at 11:13:05AM +0200, Marcin Niestroj wrote:
> Support was added based on Goodix GitHub repo [1]. There are two major
> differences between gt1151 and currently supported devices (gt9x):
> * CONFIG_DATA register has 0x8050 address instead of 0x8047,
> * config data checksum has 16-bit width instead of 8-bit.
>
> Also update goodix_i2c_test() function, so it reads ID register (which
> has the same address for all devices) instead of CONFIG_DATA (because
> its address is known only after reading ID of the device).
>
> [1] https://github.com/goodix/gt1x_driver_generic
>
> Signed-off-by: Marcin Niestroj <m.niestroj-z3quKL4iOrmQ6ZAhV5LmOA@public.gmane.org>
> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Applied, thank you.
> ---
> Changes v1 -> v2:
> * Use constant chip data, which is assigned during probe, based on
> read chip id (suggested by Dmitry)
> * Use function pointer for checsum verification
> (suggested by Antonio)
>
> .../bindings/input/touchscreen/goodix.txt | 3 +-
> drivers/input/touchscreen/goodix.c | 125 ++++++++++++++++-----
> 2 files changed, 100 insertions(+), 28 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
> index c98757a69110..0c369d8ebcab 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
> @@ -2,7 +2,8 @@ Device tree bindings for Goodix GT9xx series touchscreen controller
>
> Required properties:
>
> - - compatible : Should be "goodix,gt911"
> + - compatible : Should be "goodix,gt1151"
> + or "goodix,gt911"
> or "goodix,gt9110"
> or "goodix,gt912"
> or "goodix,gt927"
> diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
> index b3bbad7d2282..69d0b8cbc71f 100644
> --- a/drivers/input/touchscreen/goodix.c
> +++ b/drivers/input/touchscreen/goodix.c
> @@ -31,9 +31,18 @@
> #include <linux/of.h>
> #include <asm/unaligned.h>
>
> +struct goodix_ts_data;
> +
> +struct goodix_chip_data {
> + u16 config_addr;
> + int config_len;
> + int (*check_config)(struct goodix_ts_data *, const struct firmware *);
> +};
> +
> struct goodix_ts_data {
> struct i2c_client *client;
> struct input_dev *input_dev;
> + const struct goodix_chip_data *chip;
> int abs_x_max;
> int abs_y_max;
> bool swapped_x_y;
> @@ -41,7 +50,6 @@ struct goodix_ts_data {
> bool inverted_y;
> unsigned int max_touch_num;
> unsigned int int_trigger_type;
> - int cfg_len;
> struct gpio_desc *gpiod_int;
> struct gpio_desc *gpiod_rst;
> u16 id;
> @@ -69,7 +77,8 @@ struct goodix_ts_data {
> #define GOODIX_CMD_SCREEN_OFF 0x05
>
> #define GOODIX_READ_COOR_ADDR 0x814E
> -#define GOODIX_REG_CONFIG_DATA 0x8047
> +#define GOODIX_GT1X_REG_CONFIG_DATA 0x8050
> +#define GOODIX_GT9X_REG_CONFIG_DATA 0x8047
> #define GOODIX_REG_ID 0x8140
>
> #define GOODIX_BUFFER_STATUS_READY BIT(7)
> @@ -79,6 +88,35 @@ struct goodix_ts_data {
> #define MAX_CONTACTS_LOC 5
> #define TRIGGER_LOC 6
>
> +static int goodix_check_cfg_8(struct goodix_ts_data *ts,
> + const struct firmware *cfg);
> +static int goodix_check_cfg_16(struct goodix_ts_data *ts,
> + const struct firmware *cfg);
> +
> +static const struct goodix_chip_data gt1x_chip_data = {
> + .config_addr = GOODIX_GT1X_REG_CONFIG_DATA,
> + .config_len = GOODIX_CONFIG_MAX_LENGTH,
> + .check_config = goodix_check_cfg_16,
> +};
> +
> +static const struct goodix_chip_data gt911_chip_data = {
> + .config_addr = GOODIX_GT9X_REG_CONFIG_DATA,
> + .config_len = GOODIX_CONFIG_911_LENGTH,
> + .check_config = goodix_check_cfg_8,
> +};
> +
> +static const struct goodix_chip_data gt967_chip_data = {
> + .config_addr = GOODIX_GT9X_REG_CONFIG_DATA,
> + .config_len = GOODIX_CONFIG_967_LENGTH,
> + .check_config = goodix_check_cfg_8,
> +};
> +
> +static const struct goodix_chip_data gt9x_chip_data = {
> + .config_addr = GOODIX_GT9X_REG_CONFIG_DATA,
> + .config_len = GOODIX_CONFIG_MAX_LENGTH,
> + .check_config = goodix_check_cfg_8,
> +};
> +
> static const unsigned long goodix_irq_flags[] = {
> IRQ_TYPE_EDGE_RISING,
> IRQ_TYPE_EDGE_FALLING,
> @@ -177,22 +215,25 @@ static int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value)
> return goodix_i2c_write(client, reg, &value, sizeof(value));
> }
>
> -static int goodix_get_cfg_len(u16 id)
> +static const struct goodix_chip_data *goodix_get_chip_data(u16 id)
> {
> switch (id) {
> + case 1151:
> + return >1x_chip_data;
> +
> case 911:
> case 9271:
> case 9110:
> case 927:
> case 928:
> - return GOODIX_CONFIG_911_LENGTH;
> + return >911_chip_data;
>
> case 912:
> case 967:
> - return GOODIX_CONFIG_967_LENGTH;
> + return >967_chip_data;
>
> default:
> - return GOODIX_CONFIG_MAX_LENGTH;
> + return >9x_chip_data;
> }
> }
>
> @@ -332,25 +373,12 @@ static int goodix_request_irq(struct goodix_ts_data *ts)
> ts->irq_flags, ts->client->name, ts);
> }
>
> -/**
> - * goodix_check_cfg - Checks if config fw is valid
> - *
> - * @ts: goodix_ts_data pointer
> - * @cfg: firmware config data
> - */
> -static int goodix_check_cfg(struct goodix_ts_data *ts,
> - const struct firmware *cfg)
> +static int goodix_check_cfg_8(struct goodix_ts_data *ts,
> + const struct firmware *cfg)
> {
> - int i, raw_cfg_len;
> + int i, raw_cfg_len = cfg->size - 2;
> u8 check_sum = 0;
>
> - if (cfg->size > GOODIX_CONFIG_MAX_LENGTH) {
> - dev_err(&ts->client->dev,
> - "The length of the config fw is not correct");
> - return -EINVAL;
> - }
> -
> - raw_cfg_len = cfg->size - 2;
> for (i = 0; i < raw_cfg_len; i++)
> check_sum += cfg->data[i];
> check_sum = (~check_sum) + 1;
> @@ -369,6 +397,48 @@ static int goodix_check_cfg(struct goodix_ts_data *ts,
> return 0;
> }
>
> +static int goodix_check_cfg_16(struct goodix_ts_data *ts,
> + const struct firmware *cfg)
> +{
> + int i, raw_cfg_len = cfg->size - 3;
> + u16 check_sum = 0;
> +
> + for (i = 0; i < raw_cfg_len; i += 2)
> + check_sum += get_unaligned_be16(&cfg->data[i]);
> + check_sum = (~check_sum) + 1;
> + if (check_sum != get_unaligned_be16(&cfg->data[raw_cfg_len])) {
> + dev_err(&ts->client->dev,
> + "The checksum of the config fw is not correct");
> + return -EINVAL;
> + }
> +
> + if (cfg->data[raw_cfg_len + 2] != 1) {
> + dev_err(&ts->client->dev,
> + "Config fw must have Config_Fresh register set");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * goodix_check_cfg - Checks if config fw is valid
> + *
> + * @ts: goodix_ts_data pointer
> + * @cfg: firmware config data
> + */
> +static int goodix_check_cfg(struct goodix_ts_data *ts,
> + const struct firmware *cfg)
> +{
> + if (cfg->size > GOODIX_CONFIG_MAX_LENGTH) {
> + dev_err(&ts->client->dev,
> + "The length of the config fw is not correct");
> + return -EINVAL;
> + }
> +
> + return ts->chip->check_config(ts, cfg);
> +}
> +
> /**
> * goodix_send_cfg - Write fw config to device
> *
> @@ -384,7 +454,7 @@ static int goodix_send_cfg(struct goodix_ts_data *ts,
> if (error)
> return error;
>
> - error = goodix_i2c_write(ts->client, GOODIX_REG_CONFIG_DATA, cfg->data,
> + error = goodix_i2c_write(ts->client, ts->chip->config_addr, cfg->data,
> cfg->size);
> if (error) {
> dev_err(&ts->client->dev, "Failed to write config data: %d",
> @@ -511,8 +581,8 @@ static void goodix_read_config(struct goodix_ts_data *ts)
> u8 config[GOODIX_CONFIG_MAX_LENGTH];
> int error;
>
> - error = goodix_i2c_read(ts->client, GOODIX_REG_CONFIG_DATA,
> - config, ts->cfg_len);
> + error = goodix_i2c_read(ts->client, ts->chip->config_addr,
> + config, ts->chip->config_len);
> if (error) {
> dev_warn(&ts->client->dev,
> "Error reading config (%d), using defaults\n",
> @@ -592,7 +662,7 @@ static int goodix_i2c_test(struct i2c_client *client)
> u8 test;
>
> while (retry++ < 2) {
> - error = goodix_i2c_read(client, GOODIX_REG_CONFIG_DATA,
> + error = goodix_i2c_read(client, GOODIX_REG_ID,
> &test, 1);
> if (!error)
> return 0;
> @@ -762,7 +832,7 @@ static int goodix_ts_probe(struct i2c_client *client,
> return error;
> }
>
> - ts->cfg_len = goodix_get_cfg_len(ts->id);
> + ts->chip = goodix_get_chip_data(ts->id);
>
> if (ts->gpiod_int && ts->gpiod_rst) {
> /* update device config */
> @@ -891,6 +961,7 @@ MODULE_DEVICE_TABLE(acpi, goodix_acpi_match);
>
> #ifdef CONFIG_OF
> static const struct of_device_id goodix_of_match[] = {
> + { .compatible = "goodix,gt1151" },
> { .compatible = "goodix,gt911" },
> { .compatible = "goodix,gt9110" },
> { .compatible = "goodix,gt912" },
> --
> 2.14.2
>
--
Dmitry
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
prev parent reply other threads:[~2017-10-24 18:07 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-10-24 9:13 [PATCH v2] Input: goodix - support gt1151 touchpanel Marcin Niestroj
[not found] ` <20171024091305.16411-1-m.niestroj-z3quKL4iOrmQ6ZAhV5LmOA@public.gmane.org>
2017-10-24 18:07 ` Dmitry Torokhov [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171024180740.ozcyvsk5zji3hpcn@dtor-ws \
--to=dmitry.torokhov-re5jqeeqqe8avxtiumwx3w@public.gmane.org \
--cc=ao2-qKGr9MkilAE@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=hadess-0MeiytkfxGOsTnJN9+BGXg@public.gmane.org \
--cc=linux-input-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=m.niestroj-z3quKL4iOrmQ6ZAhV5LmOA@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox