[PATCH 12/22] net/ethernet/8390: remove stnic

[Christoph Hellwig <hch@lst.de>]

Now that arch/sh is removed this driver is dead code.

Signed-off-by: Christoph Hellwig <hch@lst.de>
---
 drivers/net/ethernet/8390/Kconfig  |  12 --
 drivers/net/ethernet/8390/Makefile |   1 -
 drivers/net/ethernet/8390/stnic.c  | 302 -----------------------------
 3 files changed, 315 deletions(-)
 delete mode 100644 drivers/net/ethernet/8390/stnic.c

diff --git a/drivers/net/ethernet/8390/Kconfig b/drivers/net/ethernet/8390/Kconfig
index eb90de04c88419..a7976743be9ee3 100644
--- a/drivers/net/ethernet/8390/Kconfig
+++ b/drivers/net/ethernet/8390/Kconfig
@@ -155,18 +155,6 @@ config PCMCIA_PCNET
 	  To compile this driver as a module, choose M here: the module will be
 	  called pcnet_cs.  If unsure, say N.
 
-config STNIC
-	tristate "National DP83902AV  support"
-	depends on SUPERH
-	select CRC32
-	help
-	  Support for cards based on the National Semiconductor DP83902AV
-	  ST-NIC Serial Network Interface Controller for Twisted Pair.  This
-	  is a 10Mbit/sec Ethernet controller.  Product overview and specs at
-	  <http://www.national.com/pf/DP/DP83902A.html>.
-
-	  If unsure, say N.
-
 config ULTRA
 	tristate "SMC Ultra support"
 	depends on ISA
diff --git a/drivers/net/ethernet/8390/Makefile b/drivers/net/ethernet/8390/Makefile
index 85c83c566ec663..3819a3bb75a1c9 100644
--- a/drivers/net/ethernet/8390/Makefile
+++ b/drivers/net/ethernet/8390/Makefile
@@ -13,7 +13,6 @@ obj-$(CONFIG_NE2000) += ne.o 8390p.o
 obj-$(CONFIG_NE2K_PCI) += ne2k-pci.o 8390.o
 obj-$(CONFIG_PCMCIA_AXNET) += axnet_cs.o 8390.o
 obj-$(CONFIG_PCMCIA_PCNET) += pcnet_cs.o 8390.o
-obj-$(CONFIG_STNIC) += stnic.o 8390.o
 obj-$(CONFIG_ULTRA) += smc-ultra.o 8390.o
 obj-$(CONFIG_WD80x3) += wd.o 8390.o
 obj-$(CONFIG_XSURF100) += xsurf100.o
diff --git a/drivers/net/ethernet/8390/stnic.c b/drivers/net/ethernet/8390/stnic.c
deleted file mode 100644
index bd89ca8a92dfbc..00000000000000
--- a/drivers/net/ethernet/8390/stnic.c
+++ /dev/null
@@ -1,302 +0,0 @@
-/* stnic.c : A SH7750 specific part of driver for NS DP83902A ST-NIC.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 1999 kaz Kojima
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-
-#include <asm/io.h>
-#include <mach-se/mach/se.h>
-#include <asm/machvec.h>
-#ifdef CONFIG_SH_STANDARD_BIOS
-#include <asm/sh_bios.h>
-#endif
-
-#include "8390.h"
-
-#define DRV_NAME "stnic"
-
-#define byte	unsigned char
-#define half	unsigned short
-#define word	unsigned int
-#define vbyte	volatile unsigned char
-#define vhalf	volatile unsigned short
-#define vword	volatile unsigned int
-
-#define STNIC_RUN	0x01	/* 1 == Run, 0 == reset. */
-
-#define START_PG	0	/* First page of TX buffer */
-#define STOP_PG		128	/* Last page +1 of RX ring */
-
-/* Alias */
-#define STNIC_CR	E8390_CMD
-#define PG0_RSAR0	EN0_RSARLO
-#define PG0_RSAR1	EN0_RSARHI
-#define PG0_RBCR0	EN0_RCNTLO
-#define PG0_RBCR1	EN0_RCNTHI
-
-#define CR_RRD		E8390_RREAD
-#define CR_RWR		E8390_RWRITE
-#define CR_PG0		E8390_PAGE0
-#define CR_STA		E8390_START
-#define CR_RDMA		E8390_NODMA
-
-/* FIXME! YOU MUST SET YOUR OWN ETHER ADDRESS.  */
-static byte stnic_eadr[6] =
-{0x00, 0xc0, 0x6e, 0x00, 0x00, 0x07};
-
-static struct net_device *stnic_dev;
-
-static void stnic_reset (struct net_device *dev);
-static void stnic_get_hdr (struct net_device *dev, struct e8390_pkt_hdr *hdr,
-			   int ring_page);
-static void stnic_block_input (struct net_device *dev, int count,
-			       struct sk_buff *skb , int ring_offset);
-static void stnic_block_output (struct net_device *dev, int count,
-				const unsigned char *buf, int start_page);
-
-static void stnic_init (struct net_device *dev);
-
-static u32 stnic_msg_enable;
-
-module_param_named(msg_enable, stnic_msg_enable, uint, 0444);
-MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");
-
-/* SH7750 specific read/write io. */
-static inline void
-STNIC_DELAY (void)
-{
-  vword trash;
-  trash = *(vword *) 0xa0000000;
-  trash = *(vword *) 0xa0000000;
-  trash = *(vword *) 0xa0000000;
-}
-
-static inline byte
-STNIC_READ (int reg)
-{
-  byte val;
-
-  val = (*(vhalf *) (PA_83902 + ((reg) << 1)) >> 8) & 0xff;
-  STNIC_DELAY ();
-  return val;
-}
-
-static inline void
-STNIC_WRITE (int reg, byte val)
-{
-  *(vhalf *) (PA_83902 + ((reg) << 1)) = ((half) (val) << 8);
-  STNIC_DELAY ();
-}
-
-static int __init stnic_probe(void)
-{
-  struct net_device *dev;
-  struct ei_device *ei_local;
-  int err;
-
-  /* If we are not running on a SolutionEngine, give up now */
-  if (! MACH_SE)
-    return -ENODEV;
-
-  /* New style probing API */
-  dev = alloc_ei_netdev();
-  if (!dev)
-	return -ENOMEM;
-
-#ifdef CONFIG_SH_STANDARD_BIOS
-  sh_bios_get_node_addr (stnic_eadr);
-#endif
-  eth_hw_addr_set(dev, stnic_eadr);
-
-  /* Set the base address to point to the NIC, not the "real" base! */
-  dev->base_addr = 0x1000;
-  dev->irq = IRQ_STNIC;
-  dev->netdev_ops = &ei_netdev_ops;
-
-  /* Snarf the interrupt now.  There's no point in waiting since we cannot
-     share and the board will usually be enabled. */
-  err = request_irq (dev->irq, ei_interrupt, 0, DRV_NAME, dev);
-  if (err)  {
-	netdev_emerg(dev, " unable to get IRQ %d.\n", dev->irq);
-	free_netdev(dev);
-	return err;
-  }
-
-  ei_status.name = dev->name;
-  ei_status.word16 = 1;
-#ifdef __LITTLE_ENDIAN__
-  ei_status.bigendian = 0;
-#else
-  ei_status.bigendian = 1;
-#endif
-  ei_status.tx_start_page = START_PG;
-  ei_status.rx_start_page = START_PG + TX_PAGES;
-  ei_status.stop_page = STOP_PG;
-
-  ei_status.reset_8390 = &stnic_reset;
-  ei_status.get_8390_hdr = &stnic_get_hdr;
-  ei_status.block_input = &stnic_block_input;
-  ei_status.block_output = &stnic_block_output;
-
-  stnic_init (dev);
-  ei_local = netdev_priv(dev);
-  ei_local->msg_enable = stnic_msg_enable;
-
-  err = register_netdev(dev);
-  if (err) {
-    free_irq(dev->irq, dev);
-    free_netdev(dev);
-    return err;
-  }
-  stnic_dev = dev;
-
-  netdev_info(dev, "NS ST-NIC 83902A\n");
-
-  return 0;
-}
-
-static void
-stnic_reset (struct net_device *dev)
-{
-  struct ei_device *ei_local = netdev_priv(dev);
-
-  *(vhalf *) PA_83902_RST = 0;
-  udelay (5);
-  netif_warn(ei_local, hw, dev, "8390 reset done (%ld).\n", jiffies);
-  *(vhalf *) PA_83902_RST = ~0;
-  udelay (5);
-}
-
-static void
-stnic_get_hdr (struct net_device *dev, struct e8390_pkt_hdr *hdr,
-	       int ring_page)
-{
-  struct ei_device *ei_local = netdev_priv(dev);
-
-  half buf[2];
-
-  STNIC_WRITE (PG0_RSAR0, 0);
-  STNIC_WRITE (PG0_RSAR1, ring_page);
-  STNIC_WRITE (PG0_RBCR0, 4);
-  STNIC_WRITE (PG0_RBCR1, 0);
-  STNIC_WRITE (STNIC_CR, CR_RRD | CR_PG0 | CR_STA);
-
-  buf[0] = *(vhalf *) PA_83902_IF;
-  STNIC_DELAY ();
-  buf[1] = *(vhalf *) PA_83902_IF;
-  STNIC_DELAY ();
-  hdr->next = buf[0] >> 8;
-  hdr->status = buf[0] & 0xff;
-#ifdef __LITTLE_ENDIAN__
-  hdr->count = buf[1];
-#else
-  hdr->count = ((buf[1] >> 8) & 0xff) | (buf[1] << 8);
-#endif
-
-  netif_dbg(ei_local, probe, dev, "ring %x status %02x next %02x count %04x.\n",
-	    ring_page, hdr->status, hdr->next, hdr->count);
-
-  STNIC_WRITE (STNIC_CR, CR_RDMA | CR_PG0 | CR_STA);
-}
-
-/* Block input and output, similar to the Crynwr packet driver. If you are
-   porting to a new ethercard look at the packet driver source for hints.
-   The HP LAN doesn't use shared memory -- we put the packet
-   out through the "remote DMA" dataport. */
-
-static void
-stnic_block_input (struct net_device *dev, int length, struct sk_buff *skb,
-		   int offset)
-{
-  char *buf = skb->data;
-  half val;
-
-  STNIC_WRITE (PG0_RSAR0, offset & 0xff);
-  STNIC_WRITE (PG0_RSAR1, offset >> 8);
-  STNIC_WRITE (PG0_RBCR0, length & 0xff);
-  STNIC_WRITE (PG0_RBCR1, length >> 8);
-  STNIC_WRITE (STNIC_CR, CR_RRD | CR_PG0 | CR_STA);
-
-  if (length & 1)
-    length++;
-
-  while (length > 0)
-    {
-      val = *(vhalf *) PA_83902_IF;
-#ifdef __LITTLE_ENDIAN__
-      *buf++ = val & 0xff;
-      *buf++ = val >> 8;
-#else
-      *buf++ = val >> 8;
-      *buf++ = val & 0xff;
-#endif
-      STNIC_DELAY ();
-      length -= sizeof (half);
-    }
-
-  STNIC_WRITE (STNIC_CR, CR_RDMA | CR_PG0 | CR_STA);
-}
-
-static void
-stnic_block_output (struct net_device *dev, int length,
-		    const unsigned char *buf, int output_page)
-{
-  STNIC_WRITE (PG0_RBCR0, 1);	/* Write non-zero value */
-  STNIC_WRITE (STNIC_CR, CR_RRD | CR_PG0 | CR_STA);
-  STNIC_DELAY ();
-
-  STNIC_WRITE (PG0_RBCR0, length & 0xff);
-  STNIC_WRITE (PG0_RBCR1, length >> 8);
-  STNIC_WRITE (PG0_RSAR0, 0);
-  STNIC_WRITE (PG0_RSAR1, output_page);
-  STNIC_WRITE (STNIC_CR, CR_RWR | CR_PG0 | CR_STA);
-
-  if (length & 1)
-    length++;
-
-  while (length > 0)
-    {
-#ifdef __LITTLE_ENDIAN__
-      *(vhalf *) PA_83902_IF = ((half) buf[1] << 8) | buf[0];
-#else
-      *(vhalf *) PA_83902_IF = ((half) buf[0] << 8) | buf[1];
-#endif
-      STNIC_DELAY ();
-      buf += sizeof (half);
-      length -= sizeof (half);
-    }
-
-  STNIC_WRITE (STNIC_CR, CR_RDMA | CR_PG0 | CR_STA);
-}
-
-/* This function resets the STNIC if something screws up.  */
-static void
-stnic_init (struct net_device *dev)
-{
-  stnic_reset (dev);
-  NS8390_init (dev, 0);
-}
-
-static void __exit stnic_cleanup(void)
-{
-	unregister_netdev(stnic_dev);
-	free_irq(stnic_dev->irq, stnic_dev);
-	free_netdev(stnic_dev);
-}
-
-module_init(stnic_probe);
-module_exit(stnic_cleanup);
-MODULE_LICENSE("GPL");
-- 
2.39.0