[PATCH v2 0/2] STMPE device tree bindings

[PATCH v2 0/2] STMPE device tree bindings

[Linus Walleij]

This adds the missing GPIO bindings for the STMPE port expander
and converts the existing MFD binding to YAML.

ChangeLog v1->v2:
- Split off a separate GPIO binding
- Updated the MFD binding according to feedback

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
Linus Walleij (2):
      dt-bindings: gpio: Add STMPE YAML DT schema
      dt-bindings: MFD: Convert STMPE to YAML schema

 .../devicetree/bindings/gpio/st,stmpe-gpio.yaml    |  60 +++++
 .../devicetree/bindings/input/stmpe-keypad.txt     |  41 ---
 .../bindings/input/touchscreen/stmpe.txt           | 108 --------
 .../devicetree/bindings/mfd/st,stmpe.yaml          | 298 +++++++++++++++++++++
 Documentation/devicetree/bindings/mfd/stmpe.txt    |  42 ---
 5 files changed, 358 insertions(+), 191 deletions(-)
---
base-commit: 457391b0380335d5e9a5babdec90ac53928b23b4
change-id: 20230426-stmpe-dt-bindings-c3479dd71a28

Best regards,
-- 
Linus Walleij <linus.walleij@linaro.org>

[PATCH v2 1/2] dt-bindings: gpio: Add STMPE YAML DT schema

[Linus Walleij]

This adds a schema for the STMPE GPIO that while it is used a
lot in the kernel tree is anyway missing its bindings.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v1->v2:
- New patch split off from the MFD patch.
---
 .../devicetree/bindings/gpio/st,stmpe-gpio.yaml    | 60 ++++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/Documentation/devicetree/bindings/gpio/st,stmpe-gpio.yaml b/Documentation/devicetree/bindings/gpio/st,stmpe-gpio.yaml
new file mode 100644
index 000000000000..6e991ebbdf77
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/st,stmpe-gpio.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/st,stmpe-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectonics Port Expander (STMPE) GPIO Block
+
+description: STMicroelectronics Port Expander (STMPE) is a series of slow
+  bus controllers for various expanded peripherals such as GPIO, keypad,
+  touchscreen, ADC, PWM or rotator. It can contain one or several different
+  peripherals connected to SPI or I2C. These bindings pertain to the
+  GPIO portions of these expanders.
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+properties:
+  compatible:
+    const: st,stmpe-gpio
+
+  "#gpio-cells":
+    const: 2
+
+  "#interrupt-cells":
+    const: 2
+
+  gpio-controller: true
+
+  interrupt-controller: true
+
+  st,norequest-mask:
+    description: A bitmask of GPIO lines that cannot be requested because for
+      for example not being connected to anything on the system
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+patternProperties:
+  "^.+-hog(-[0-9]+)?$":
+    type: object
+
+    properties:
+      gpio-hog: true
+      gpios: true
+      input: true
+      output-high: true
+      output-low: true
+      line-name: true
+
+    required:
+      - gpio-hog
+      - gpios
+
+additionalProperties: false
+
+required:
+  - compatible
+  - "#gpio-cells"
+  - "#interrupt-cells"
+  - gpio-controller
+  - interrupt-controller

-- 
2.34.1

[PATCH v2 2/2] dt-bindings: MFD: Convert STMPE to YAML schema

[Linus Walleij]

This converts the STMPE MFD device tree bindings to the YAML
schema.

Reference the existing schema for the ADC, just define the
other subnode schemas directly in the MFD schema.

Add two examples so we have examples covering both the simple
GPIO expander and the more complex with ADC and touchscreen.

Some in-tree users do not follow the naming conventions for nodes
so these DTS files need to be augmented to use proper node names
like "adc", "pwm", "gpio", "keyboard-controller" etc before the
bindings take effect on them.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v1->v2:
- Split off the GPIO bindings to their own schema, as the old
  bindings didn't even have any GPIO bindings. Put the GPIO
  schema before this schema so we can use GPIO in the examples.
- Drop nodename and pattern as STMPE is not a generic name.
- Add maxItems to the resets.
- Make wakeup-source just :true, as it is a generic property.
- Move unevaluatedProperties for subnodes right before properties
  as requested.
- Name devices "port-expander" in the examples.
- Use lowercase hex in line init.
---
 .../devicetree/bindings/input/stmpe-keypad.txt     |  41 ---
 .../bindings/input/touchscreen/stmpe.txt           | 108 --------
 .../devicetree/bindings/mfd/st,stmpe.yaml          | 298 +++++++++++++++++++++
 Documentation/devicetree/bindings/mfd/stmpe.txt    |  42 ---
 4 files changed, 298 insertions(+), 191 deletions(-)

diff --git a/Documentation/devicetree/bindings/input/stmpe-keypad.txt b/Documentation/devicetree/bindings/input/stmpe-keypad.txt
deleted file mode 100644
index 12bb771d66d4..000000000000
--- a/Documentation/devicetree/bindings/input/stmpe-keypad.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-* STMPE Keypad
-
-Required properties:
- - compatible               : "st,stmpe-keypad"
- - linux,keymap             : See ./matrix-keymap.txt
-
-Optional properties:
- - debounce-interval        : Debouncing interval time in milliseconds
- - st,scan-count            : Scanning cycles elapsed before key data is updated
- - st,no-autorepeat         : If specified device will not autorepeat
- - keypad,num-rows          : See ./matrix-keymap.txt
- - keypad,num-columns       : See ./matrix-keymap.txt
-
-Example:
-
-	stmpe_keypad {
-		compatible = "st,stmpe-keypad";
-
-		debounce-interval = <64>;
-		st,scan-count = <8>;
-		st,no-autorepeat;
-
-		linux,keymap = <0x205006b
-				0x4010074
-				0x3050072
-				0x1030004
-				0x502006a
-				0x500000a
-				0x5008b
-				0x706001c
-				0x405000b
-				0x6070003
-				0x3040067
-				0x303006c
-				0x60400e7
-				0x602009e
-				0x4020073
-				0x5050002
-				0x4030069
-				0x3020008>;
-	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
deleted file mode 100644
index 238b51555c04..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
+++ /dev/null
@@ -1,108 +0,0 @@
-STMPE Touchscreen
-----------------
-
-Required properties:
- - compatible: "st,stmpe-ts"
-
-Optional properties:
-- st,ave-ctrl		: Sample average control
-				0 -> 1 sample
-				1 -> 2 samples
-				2 -> 4 samples
-				3 -> 8 samples
-- st,touch-det-delay	: Touch detect interrupt delay (recommended is 3)
-				0 -> 10 us
-				1 -> 50 us
-				2 -> 100 us
-				3 -> 500 us
-				4 -> 1 ms
-				5 -> 5 ms
-				6 -> 10 ms
-				7 -> 50 ms
-- st,settling		: Panel driver settling time (recommended is 2)
-				0 -> 10 us
-				1 -> 100 us
-				2 -> 500 us
-				3 -> 1 ms
-				4 -> 5 ms
-				5 -> 10 ms
-				6 -> 50 ms
-				7 -> 100 ms
-- st,fraction-z		: Length of the fractional part in z (recommended is 7)
-			  (fraction-z ([0..7]) = Count of the fractional part)
-- st,i-drive		: current limit value of the touchscreen drivers
-				0 -> 20 mA (typical 35mA max)
-				1 -> 50 mA (typical 80 mA max)
-
-Optional properties common with MFD (deprecated):
- - st,sample-time	: ADC conversion time in number of clock.
-				0 -> 36 clocks
-				1 -> 44 clocks
-				2 -> 56 clocks
-				3 -> 64 clocks
-				4 -> 80 clocks (recommended)
-				5 -> 96 clocks
-				6 -> 124 clocks
- - st,mod-12b		: ADC Bit mode
-				0 -> 10bit ADC
-				1 -> 12bit ADC
- - st,ref-sel		: ADC reference source
-				0 -> internal
-				1 -> external
- - st,adc-freq		: ADC Clock speed
-				0 -> 1.625 MHz
-				1 -> 3.25 MHz
-				2 || 3 -> 6.5 MHz
-
-Node should be child node of stmpe node to which it belongs.
-
-Note that common ADC settings of stmpe_touchscreen (child) will take precedence
-over the settings done in MFD.
-
-Example:
-
-stmpe811@41 {
-	compatible = "st,stmpe811";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_touch_int>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-	reg = <0x41>;
-	interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
-	interrupt-parent = <&gpio4>;
-	interrupt-controller;
-	id = <0>;
-	blocks = <0x5>;
-	irq-trigger = <0x1>;
-	/* Common ADC settings */
-	/* 3.25 MHz ADC clock speed */
-	st,adc-freq = <1>;
-	/* 12-bit ADC */
-	st,mod-12b = <1>;
-	/* internal ADC reference */
-	st,ref-sel = <0>;
-	/* ADC converstion time: 80 clocks */
-	st,sample-time = <4>;
-
-	stmpe_touchscreen {
-		compatible = "st,stmpe-ts";
-		reg = <0>;
-		/* 8 sample average control */
-		st,ave-ctrl = <3>;
-		/* 5 ms touch detect interrupt delay */
-		st,touch-det-delay = <5>;
-		/* 1 ms panel driver settling time */
-		st,settling = <3>;
-		/* 7 length fractional part in z */
-		st,fraction-z = <7>;
-		/*
-		 * 50 mA typical 80 mA max touchscreen drivers
-		 * current limit value
-		 */
-		st,i-drive = <1>;
-	};
-	stmpe_adc {
-		compatible = "st,stmpe-adc";
-		st,norequest-mask = <0x0F>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/mfd/st,stmpe.yaml b/Documentation/devicetree/bindings/mfd/st,stmpe.yaml
new file mode 100644
index 000000000000..dd24ae2d5fb4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/st,stmpe.yaml
@@ -0,0 +1,298 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/st,stmpe.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectonics Port Expander (STMPE)
+
+description: STMicroelectronics Port Expander (STMPE) is a series of slow
+  bus controllers for various expanded peripherals such as GPIO, keypad,
+  touchscreen, ADC, PWM or rotator. It can contain one or several different
+  peripherals connected to SPI or I2C.
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+properties:
+  compatible:
+    enum:
+      - st,stmpe601
+      - st,stmpe801
+      - st,stmpe811
+      - st,stmpe1600
+      - st,stmpe1601
+      - st,stmpe2401
+      - st,stmpe2403
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  vcc-supply: true
+
+  vio-supply: true
+
+  reset-gpios:
+    maxItems: 1
+
+  wakeup-source: true
+
+  st,autosleep-timeout:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 4, 16, 32, 64, 128, 256, 512, 1024 ]
+    description: Time idle before going to automatic sleep to save power
+
+  st,sample-time:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 0, 1, 2, 3, 4, 5, 6 ]
+    description: |
+      Sample time per iteration
+      0 = 36 clock ticks
+      1 = 44 clock ticks
+      2 = 56 clock ticks
+      3 = 64 clock ticks
+      4 = 80 clock ticks - recommended
+      5 = 96 clock ticks
+      6 = 124 clock ticks
+
+  st,mod-12b:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 0, 1 ]
+    description: ADC bit mode 0 = 10bit ADC, 1 = 12bit ADC
+
+  st,ref-sel:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 0, 1 ]
+    description: ADC reference source 0 = internal, 1 = external
+
+  st,adc-freq:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 0, 1, 2, 3 ]
+    description: |
+      ADC clock speed
+      0 = 1.625 MHz
+      1 = 3.25 MHz
+      2, 3 = 6.5 MHz
+
+  adc:
+    type: object
+    $ref: /schemas/iio/adc/st,stmpe-adc.yaml#
+
+  gpio:
+    type: object
+    $ref: /schemas/gpio/st,stmpe-gpio.yaml#
+
+  keyboard-controller:
+    type: object
+    $ref: /schemas/input/matrix-keymap.yaml#
+
+    unevaluatedProperties: false
+
+    properties:
+      compatible:
+        const: st,stmpe-keypad
+
+      debounce-interval:
+        description: Debouncing interval in milliseconds
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+      st,no-autorepeat:
+        description: If present, the keys will not autorepeat when pressed
+        $ref: /schemas/types.yaml#/definitions/flag
+
+      st,scan-count:
+        description: Scanning cycles elapsed before key data is updated
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+    required:
+      - compatible
+      - linux,keymap
+
+  pwm:
+    type: object
+    $ref: /schemas/pwm/pwm.yaml#
+
+    unevaluatedProperties: false
+
+    properties:
+      compatible:
+        const: st,stmpe-pwm
+
+    required:
+      - compatible
+      - "#pwm-cells"
+
+  touchscreen:
+    type: object
+    $ref: /schemas/input/touchscreen/touchscreen.yaml#
+
+    unevaluatedProperties: false
+
+    properties:
+      compatible:
+        const: st,stmpe-ts
+
+      st,ave-ctrl:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [ 0, 1, 2, 3 ]
+        description: |
+          Sample average control
+          0 = 1 sample
+          1 = 2 samples
+          2 = 4 samples
+          3 = 8 samples
+
+      st,touch-det-delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
+        description: |
+          Touch detection delay
+          0 = 10 us
+          1 = 50 us
+          2 = 100 us
+          3 = 500 us - recommended
+          4 = 1 ms
+          5 = 5 ms
+          6 = 10 ms
+          7 = 50 ms
+
+      st,settling:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
+        description: |
+          Panel driver settling time
+          0 = 10 us
+          1 = 100 us
+          2 = 500 us - recommended
+          3 = 1 ms
+          4 = 5 ms
+          5 = 10 ms
+          6 = 50 ms
+          7 = 100 ms
+
+      st,fraction-z:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
+        description: Length of the fractional part in z, recommended is 7
+          (fraction-z ([0..7]) = Count of the fractional part)
+
+      st,i-drive:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [ 0, 1 ]
+        description: |
+          current limit value of the touchscreen drivers
+          0 = 20 mA (typical 35 mA max)
+          1 = 50 mA (typical 80 mA max)
+
+    required:
+      - compatible
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/input/input.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      port-expander@43 {
+        compatible = "st,stmpe2401";
+        reg = <0x43>;
+        reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+        interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+        interrupt-parent = <&gpio>;
+        vcc-supply = <&db8500_vsmps2_reg>;
+        vio-supply = <&db8500_vsmps2_reg>;
+        wakeup-source;
+        st,autosleep-timeout = <1024>;
+
+        gpio {
+          compatible = "st,stmpe-gpio";
+          gpio-controller;
+          #gpio-cells = <2>;
+          interrupt-controller;
+          #interrupt-cells = <2>;
+          st,norequest-mask = <0xf0f002>;
+        };
+
+        keyboard-controller {
+          compatible = "st,stmpe-keypad";
+          debounce-interval = <64>;
+          st,scan-count = <8>;
+          st,no-autorepeat;
+          keypad,num-rows = <8>;
+          keypad,num-columns = <8>;
+          linux,keymap = <
+              MATRIX_KEY(0x00, 0x00, KEY_1)
+              MATRIX_KEY(0x00, 0x01, KEY_2)
+              MATRIX_KEY(0x00, 0x02, KEY_3)
+              MATRIX_KEY(0x00, 0x03, KEY_4)
+              MATRIX_KEY(0x00, 0x04, KEY_5)
+              MATRIX_KEY(0x00, 0x05, KEY_6)
+              MATRIX_KEY(0x00, 0x06, KEY_7)
+              MATRIX_KEY(0x00, 0x07, KEY_8)
+              MATRIX_KEY(0x00, 0x08, KEY_9)
+              MATRIX_KEY(0x00, 0x09, KEY_0)
+          >;
+        };
+
+        pwm {
+          compatible = "st,stmpe-pwm";
+          #pwm-cells = <2>;
+        };
+      };
+
+      port-expander@41 {
+        compatible = "st,stmpe811";
+        reg = <0x41>;
+        interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+        interrupt-parent = <&gpio>;
+        st,adc-freq = <1>;
+        st,mod-12b = <1>;
+        st,ref-sel = <0>;
+        st,sample-time = <4>;
+
+        adc {
+          compatible = "st,stmpe-adc";
+          st,norequest-mask = <0x0f>;
+          #io-channel-cells = <1>;
+        };
+
+        gpio {
+          compatible = "st,stmpe-gpio";
+          gpio-controller;
+          #gpio-cells = <2>;
+          interrupt-controller;
+          #interrupt-cells = <2>;
+        };
+
+        pwm {
+          compatible = "st,stmpe-pwm";
+          #pwm-cells = <2>;
+        };
+
+        touchscreen {
+          compatible = "st,stmpe-ts";
+          st,ave-ctrl = <3>;
+          st,touch-det-delay = <5>;
+          st,settling = <3>;
+          st,fraction-z = <7>;
+          st,i-drive = <1>;
+        };
+      };
+    };
+...
diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt
deleted file mode 100644
index d4408a417193..000000000000
--- a/Documentation/devicetree/bindings/mfd/stmpe.txt
+++ /dev/null
@@ -1,42 +0,0 @@
-* ST Microelectronics STMPE Multi-Functional Device
-
-STMPE is an MFD device which may expose the following inbuilt devices: gpio,
-keypad, touchscreen, adc, pwm, rotator.
-
-Required properties:
- - compatible			: "st,stmpe[610|801|811|1600|1601|2401|2403]"
- - reg				: I2C/SPI address of the device
-
-Optional properties:
- - interrupts			: The interrupt outputs from the controller
- - interrupt-controller		: Marks the device node as an interrupt controller
- - wakeup-source		: Marks the input device as wakable
- - st,autosleep-timeout		: Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
- - irq-gpio			: If present, which GPIO to use for event IRQ
-
-Optional properties for devices with touch and ADC (STMPE811|STMPE610):
- - st,sample-time		: ADC conversion time in number of clock.
-					0 -> 36 clocks		4 -> 80 clocks (recommended)
-					1 -> 44 clocks		5 -> 96 clocks
-					2 -> 56 clocks		6 -> 124 clocks
-					3 -> 64 clocks
- - st,mod-12b			: ADC Bit mode
-					0 -> 10bit ADC		1 -> 12bit ADC
- - st,ref-sel			: ADC reference source
-					0 -> internal		1 -> external
- - st,adc-freq			: ADC Clock speed
-					0 -> 1.625 MHz		2 || 3 -> 6.5 MHz
-					1 -> 3.25 MHz
-
-Example:
-
-	stmpe1601: stmpe1601@40 {
-		compatible = "st,stmpe1601";
-		reg = <0x40>;
-		interrupts = <26 0x4>;
-		interrupt-parent = <&gpio6>;
-		interrupt-controller;
-
-		wakeup-source;
-		st,autosleep-timeout = <1024>;
-	};

-- 
2.34.1

Re: [PATCH v2 1/2] dt-bindings: gpio: Add STMPE YAML DT schema

[Rob Herring]

On Wed, Apr 26, 2023 at 01:21:38PM +0200, Linus Walleij wrote:
> This adds a schema for the STMPE GPIO that while it is used a
> lot in the kernel tree is anyway missing its bindings.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> ChangeLog v1->v2:
> - New patch split off from the MFD patch.
> ---
>  .../devicetree/bindings/gpio/st,stmpe-gpio.yaml    | 60 ++++++++++++++++++++++
>  1 file changed, 60 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/gpio/st,stmpe-gpio.yaml b/Documentation/devicetree/bindings/gpio/st,stmpe-gpio.yaml
> new file mode 100644
> index 000000000000..6e991ebbdf77
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/st,stmpe-gpio.yaml
> @@ -0,0 +1,60 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/gpio/st,stmpe-gpio.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: STMicroelectonics Port Expander (STMPE) GPIO Block
> +
> +description: STMicroelectronics Port Expander (STMPE) is a series of slow
> +  bus controllers for various expanded peripherals such as GPIO, keypad,
> +  touchscreen, ADC, PWM or rotator. It can contain one or several different
> +  peripherals connected to SPI or I2C. These bindings pertain to the
> +  GPIO portions of these expanders.
> +
> +maintainers:
> +  - Linus Walleij <linus.walleij@linaro.org>
> +
> +properties:
> +  compatible:
> +    const: st,stmpe-gpio
> +
> +  "#gpio-cells":
> +    const: 2
> +
> +  "#interrupt-cells":
> +    const: 2
> +
> +  gpio-controller: true
> +
> +  interrupt-controller: true
> +
> +  st,norequest-mask:
> +    description: A bitmask of GPIO lines that cannot be requested because for
> +      for example not being connected to anything on the system
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +
> +patternProperties:
> +  "^.+-hog(-[0-9]+)?$":
> +    type: object
> +
> +    properties:
> +      gpio-hog: true
> +      gpios: true
> +      input: true
> +      output-high: true
> +      output-low: true
> +      line-name: true
> +
> +    required:
> +      - gpio-hog
> +      - gpios

All you need for hog nodes is:

"^.+-hog(-[0-9]+)?$":
  type: object
  required:
    - gpio-hog

The presence of 'gpio-hog' causes the hog schema to be applied.

Rob

Re: [PATCH v2 2/2] dt-bindings: MFD: Convert STMPE to YAML schema

[Rob Herring]

On Wed, Apr 26, 2023 at 01:21:39PM +0200, Linus Walleij wrote:
> This converts the STMPE MFD device tree bindings to the YAML
> schema.
> 
> Reference the existing schema for the ADC, just define the
> other subnode schemas directly in the MFD schema.
> 
> Add two examples so we have examples covering both the simple
> GPIO expander and the more complex with ADC and touchscreen.
> 
> Some in-tree users do not follow the naming conventions for nodes
> so these DTS files need to be augmented to use proper node names
> like "adc", "pwm", "gpio", "keyboard-controller" etc before the
> bindings take effect on them.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> ChangeLog v1->v2:
> - Split off the GPIO bindings to their own schema, as the old
>   bindings didn't even have any GPIO bindings. Put the GPIO
>   schema before this schema so we can use GPIO in the examples.
> - Drop nodename and pattern as STMPE is not a generic name.
> - Add maxItems to the resets.
> - Make wakeup-source just :true, as it is a generic property.
> - Move unevaluatedProperties for subnodes right before properties
>   as requested.
> - Name devices "port-expander" in the examples.
> - Use lowercase hex in line init.
> ---
>  .../devicetree/bindings/input/stmpe-keypad.txt     |  41 ---
>  .../bindings/input/touchscreen/stmpe.txt           | 108 --------
>  .../devicetree/bindings/mfd/st,stmpe.yaml          | 298 +++++++++++++++++++++
>  Documentation/devicetree/bindings/mfd/stmpe.txt    |  42 ---
>  4 files changed, 298 insertions(+), 191 deletions(-)

> diff --git a/Documentation/devicetree/bindings/mfd/st,stmpe.yaml b/Documentation/devicetree/bindings/mfd/st,stmpe.yaml
> new file mode 100644
> index 000000000000..dd24ae2d5fb4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/st,stmpe.yaml
> @@ -0,0 +1,298 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/st,stmpe.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: STMicroelectonics Port Expander (STMPE)
> +
> +description: STMicroelectronics Port Expander (STMPE) is a series of slow
> +  bus controllers for various expanded peripherals such as GPIO, keypad,
> +  touchscreen, ADC, PWM or rotator. It can contain one or several different
> +  peripherals connected to SPI or I2C.
> +
> +maintainers:
> +  - Linus Walleij <linus.walleij@linaro.org>
> +
> +allOf:
> +  - $ref: /schemas/spi/spi-peripheral-props.yaml#
> +
> +properties:
> +  compatible:
> +    enum:
> +      - st,stmpe601
> +      - st,stmpe801
> +      - st,stmpe811
> +      - st,stmpe1600
> +      - st,stmpe1601
> +      - st,stmpe2401
> +      - st,stmpe2403
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  vcc-supply: true
> +
> +  vio-supply: true
> +
> +  reset-gpios:
> +    maxItems: 1
> +
> +  wakeup-source: true
> +
> +  st,autosleep-timeout:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 4, 16, 32, 64, 128, 256, 512, 1024 ]
> +    description: Time idle before going to automatic sleep to save power
> +
> +  st,sample-time:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 0, 1, 2, 3, 4, 5, 6 ]
> +    description: |
> +      Sample time per iteration
> +      0 = 36 clock ticks
> +      1 = 44 clock ticks
> +      2 = 56 clock ticks
> +      3 = 64 clock ticks
> +      4 = 80 clock ticks - recommended
> +      5 = 96 clock ticks
> +      6 = 124 clock ticks
> +
> +  st,mod-12b:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 0, 1 ]
> +    description: ADC bit mode 0 = 10bit ADC, 1 = 12bit ADC
> +
> +  st,ref-sel:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 0, 1 ]
> +    description: ADC reference source 0 = internal, 1 = external
> +
> +  st,adc-freq:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 0, 1, 2, 3 ]
> +    description: |
> +      ADC clock speed
> +      0 = 1.625 MHz
> +      1 = 3.25 MHz
> +      2, 3 = 6.5 MHz
> +
> +  adc:
> +    type: object
> +    $ref: /schemas/iio/adc/st,stmpe-adc.yaml#
> +
> +  gpio:
> +    type: object
> +    $ref: /schemas/gpio/st,stmpe-gpio.yaml#
> +
> +  keyboard-controller:
> +    type: object
> +    $ref: /schemas/input/matrix-keymap.yaml#
> +
> +    unevaluatedProperties: false
> +
> +    properties:
> +      compatible:
> +        const: st,stmpe-keypad
> +
> +      debounce-interval:
> +        description: Debouncing interval in milliseconds
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +
> +      st,no-autorepeat:
> +        description: If present, the keys will not autorepeat when pressed
> +        $ref: /schemas/types.yaml#/definitions/flag
> +
> +      st,scan-count:
> +        description: Scanning cycles elapsed before key data is updated
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +
> +    required:
> +      - compatible
> +      - linux,keymap
> +
> +  pwm:
> +    type: object
> +    $ref: /schemas/pwm/pwm.yaml#
> +
> +    unevaluatedProperties: false
> +
> +    properties:
> +      compatible:
> +        const: st,stmpe-pwm

You need to define what value #pwm-cells should be.

> +
> +    required:
> +      - compatible
> +      - "#pwm-cells"

pwm.yaml already requires this.

With those fixed,

Reviewed-by: Rob Herring <robh@kernel.org>

> +
> +  touchscreen:
> +    type: object
> +    $ref: /schemas/input/touchscreen/touchscreen.yaml#
> +
> +    unevaluatedProperties: false
> +
> +    properties:
> +      compatible:
> +        const: st,stmpe-ts
> +
> +      st,ave-ctrl:
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        enum: [ 0, 1, 2, 3 ]
> +        description: |
> +          Sample average control
> +          0 = 1 sample
> +          1 = 2 samples
> +          2 = 4 samples
> +          3 = 8 samples
> +
> +      st,touch-det-delay:
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
> +        description: |
> +          Touch detection delay
> +          0 = 10 us
> +          1 = 50 us
> +          2 = 100 us
> +          3 = 500 us - recommended
> +          4 = 1 ms
> +          5 = 5 ms
> +          6 = 10 ms
> +          7 = 50 ms
> +
> +      st,settling:
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
> +        description: |
> +          Panel driver settling time
> +          0 = 10 us
> +          1 = 100 us
> +          2 = 500 us - recommended
> +          3 = 1 ms
> +          4 = 5 ms
> +          5 = 10 ms
> +          6 = 50 ms
> +          7 = 100 ms
> +
> +      st,fraction-z:
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
> +        description: Length of the fractional part in z, recommended is 7
> +          (fraction-z ([0..7]) = Count of the fractional part)
> +
> +      st,i-drive:
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        enum: [ 0, 1 ]
> +        description: |
> +          current limit value of the touchscreen drivers
> +          0 = 20 mA (typical 35 mA max)
> +          1 = 50 mA (typical 80 mA max)
> +
> +    required:
> +      - compatible
> +
> +additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/input/input.h>
> +    i2c {
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +
> +      port-expander@43 {
> +        compatible = "st,stmpe2401";
> +        reg = <0x43>;
> +        reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> +        interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
> +        interrupt-parent = <&gpio>;
> +        vcc-supply = <&db8500_vsmps2_reg>;
> +        vio-supply = <&db8500_vsmps2_reg>;
> +        wakeup-source;
> +        st,autosleep-timeout = <1024>;
> +
> +        gpio {
> +          compatible = "st,stmpe-gpio";
> +          gpio-controller;
> +          #gpio-cells = <2>;
> +          interrupt-controller;
> +          #interrupt-cells = <2>;
> +          st,norequest-mask = <0xf0f002>;
> +        };
> +
> +        keyboard-controller {
> +          compatible = "st,stmpe-keypad";
> +          debounce-interval = <64>;
> +          st,scan-count = <8>;
> +          st,no-autorepeat;
> +          keypad,num-rows = <8>;
> +          keypad,num-columns = <8>;
> +          linux,keymap = <
> +              MATRIX_KEY(0x00, 0x00, KEY_1)
> +              MATRIX_KEY(0x00, 0x01, KEY_2)
> +              MATRIX_KEY(0x00, 0x02, KEY_3)
> +              MATRIX_KEY(0x00, 0x03, KEY_4)
> +              MATRIX_KEY(0x00, 0x04, KEY_5)
> +              MATRIX_KEY(0x00, 0x05, KEY_6)
> +              MATRIX_KEY(0x00, 0x06, KEY_7)
> +              MATRIX_KEY(0x00, 0x07, KEY_8)
> +              MATRIX_KEY(0x00, 0x08, KEY_9)
> +              MATRIX_KEY(0x00, 0x09, KEY_0)
> +          >;
> +        };
> +
> +        pwm {
> +          compatible = "st,stmpe-pwm";
> +          #pwm-cells = <2>;
> +        };
> +      };
> +
> +      port-expander@41 {
> +        compatible = "st,stmpe811";
> +        reg = <0x41>;
> +        interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
> +        interrupt-parent = <&gpio>;
> +        st,adc-freq = <1>;
> +        st,mod-12b = <1>;
> +        st,ref-sel = <0>;
> +        st,sample-time = <4>;
> +
> +        adc {
> +          compatible = "st,stmpe-adc";
> +          st,norequest-mask = <0x0f>;
> +          #io-channel-cells = <1>;
> +        };
> +
> +        gpio {
> +          compatible = "st,stmpe-gpio";
> +          gpio-controller;
> +          #gpio-cells = <2>;
> +          interrupt-controller;
> +          #interrupt-cells = <2>;
> +        };
> +
> +        pwm {
> +          compatible = "st,stmpe-pwm";
> +          #pwm-cells = <2>;
> +        };
> +
> +        touchscreen {
> +          compatible = "st,stmpe-ts";
> +          st,ave-ctrl = <3>;
> +          st,touch-det-delay = <5>;
> +          st,settling = <3>;
> +          st,fraction-z = <7>;
> +          st,i-drive = <1>;
> +        };
> +      };
> +    };
> +...

Re: [PATCH v2 2/2] dt-bindings: MFD: Convert STMPE to YAML schema

[Dmitry Torokhov]

On Thu, Apr 27, 2023 at 11:16:33AM -0500, Rob Herring wrote:
> On Wed, Apr 26, 2023 at 01:21:39PM +0200, Linus Walleij wrote:
> > This converts the STMPE MFD device tree bindings to the YAML
> > schema.
> > 
> > Reference the existing schema for the ADC, just define the
> > other subnode schemas directly in the MFD schema.
> > 
> > Add two examples so we have examples covering both the simple
> > GPIO expander and the more complex with ADC and touchscreen.
> > 
> > Some in-tree users do not follow the naming conventions for nodes
> > so these DTS files need to be augmented to use proper node names
> > like "adc", "pwm", "gpio", "keyboard-controller" etc before the
> > bindings take effect on them.
> > 
> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> > ---
> > ChangeLog v1->v2:
> > - Split off the GPIO bindings to their own schema, as the old
> >   bindings didn't even have any GPIO bindings. Put the GPIO
> >   schema before this schema so we can use GPIO in the examples.
> > - Drop nodename and pattern as STMPE is not a generic name.
> > - Add maxItems to the resets.
> > - Make wakeup-source just :true, as it is a generic property.
> > - Move unevaluatedProperties for subnodes right before properties
> >   as requested.
> > - Name devices "port-expander" in the examples.
> > - Use lowercase hex in line init.
> > ---
> >  .../devicetree/bindings/input/stmpe-keypad.txt     |  41 ---
> >  .../bindings/input/touchscreen/stmpe.txt           | 108 --------

Since Rob is happy with the bindings, for the input bits:

Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Thanks.

-- 
Dmitry