[PATCH v4 00/38] ARM: dts: qcom: cleanup PMIC usage

[PATCH v4 00/38] ARM: dts: qcom: cleanup PMIC usage

[Dmitry Baryshkov]

While reviewing APQ8064 CPUFreq patchset, Konrad pointed out that PMICs
are not a part of SoC and as such do not belong to the per-SoC files.

Cleanup the way 32-bit Qualcomm platforms treat PMICs:

- Move SSBI PMICs to separate files (as a bonus merging two different
  instances of PM8921, benefitting both platforms).

- Include such PMIC files only from the board files, keeping SoC file
  generic.

- Move RPM regulator definitions to board files too. They do not belong
  to the SoC dtsi files for the same reason.

- Move PMIC-specific GPIOs and supply properties to individual board
  files.

Note, enabling DT schema triggers warnings for pmic:led@48 in
qcom-apq8060-dragonboard.dts. This node uses custom ('cm3605') trigger
to make the LED follow the state of the proximity / ALS device.
Previously [1] Rob pointed out that this is not the best way and the
device should be switched to `trigger-sources' instead. However as I do
not have this device, I'm not brave enough to introduce these changes.

Note2: DT binding changes are largely independent from the DTS changes,
they can be applied separately.

[1] https://lore.kernel.org/linux-arm-msm/20221205220709.GA2713165-robh@kernel.org

Changes since v3:
- Moved PMIC interrupts to board DT files, they are not a property of
  the board, not the SoC.
- Dropped qcom, prefix from ssbi node names in ipq8064 and mdm9615 DT
  files.

Changes since v2:
- Rebased on top of linux-next to fix conflict
- Picked up dt-bindings patches from old, not-fully merged series.
- qcom,pm8921-keypad: droped the no-autorepeat property (Rob, Dmitry)
- Moved qcom,ssbi to /bus/ (Krzysztof)

Changes since v1:
- To ease reviewing break cleanups from the  "split PMIC" patches
  (Konrad).

Dmitry Baryshkov (38):
  dt-bindings: input: qcom,pm8921-keypad: convert to YAML format
  dt-bindings: mfd: qcom-pm8xxx: add missing child nodes
  dt-bindings: mfd: qcom-pm8xxx: allow using interrupts-extended
  ARM: dts: qcom: apq8064: correct XOADC register address
  ARM: dts: qcom: msm8960: introduce label for PMIC keypad
  ARM: dts: qcom: msm8660-surf: use keypad label directly
  ARM: dts: qcom: apq8064-nexus7: move sdcc1 node to proper place
  ARM: dts: qcom: mdm9615-wp8548-mangoh-green: group include clauses
  ARM: dts: qcom: strip prefix from PMIC files
  ARM: dts: qcom: apq8064: fix PMIC node labels
  ARM: dts: qcom: mdm9615: fix PMIC node labels
  ARM: dts: qcom: msm8660: fix PMIC node labels
  ARM: dts: qcom: msm8960: fix PMIC node labels
  ARM: dts: qcom: apq8064: move PMIC interrupts to the board files
  ARM: dts: qcom: mdm9615: move PMIC interrupts to the board files
  ARM: dts: qcom: msm8660: move PMIC interrupts to the board files
  ARM: dts: qcom: msm8960: move PMIC interrupts to the board files
  ARM: dts: qcom: msm8960: split PMIC to separate dtsi files
  ARM: dts: qcom: apq8064: split PMICs to separate dtsi files
  ARM: dts: qcom: mdm9615: split PMIC to separate dtsi files
  ARM: dts: qcom: msm8660: split PMIC to separate dtsi files
  ARM: dts: qcom: pm8058: reorder nodes
  ARM: dts: qcom: pm8921: reorder nodes
  ARM: dts: qcom: pm8018: move reg property
  ARM: dts: qcom: pm8921: move reg property
  ARM: dts: qcom: pm8058: use defined IRQ flags
  ARM: dts: qcom: pm8921: switch to interrupts-extended
  ARM: dts: qcom: pm8018: switch to interrupts-extended
  ARM: dts: qcom: pm8058: switch to interrupts-extended
  ARM: dts: qcom: apq8064: move RPM regulators to board files
  ARM: dts: qcom: mdm9615: move RPM regulators to board files
  ARM: dts: qcom: msm8660: move RPM regulators to board files
  ARM: dts: qcom: msm8960: drop useless rpm regulators node
  ARM: dts: qcom: msm8974: move regulators to board files
  ARM: dts: qcom: pm8921: Disable keypad by default
  ARM: dts: qcom: apq8060-dragonboard: rename mpp ADC channels to
    adc-channel
  ARM: dts: qcom: ipq8064: drop qcom, prefix from SSBI node name
  ARM: dts: qcom: mdm9615: drop qcom, prefix from SSBI node name

 .../bindings/input/qcom,pm8921-keypad.yaml    |  89 +++++++
 .../bindings/input/qcom,pm8xxx-keypad.txt     |  90 --------
 .../devicetree/bindings/mfd/qcom-pm8xxx.yaml  |  36 ++-
 arch/arm/boot/dts/qcom/pm8018.dtsi            |  55 +++++
 arch/arm/boot/dts/qcom/pm8058.dtsi            | 159 +++++++++++++
 .../qcom/{qcom-pm8226.dtsi => pm8226.dtsi}    |   0
 arch/arm/boot/dts/qcom/pm8821.dtsi            |  22 ++
 .../qcom/{qcom-pm8841.dtsi => pm8841.dtsi}    |   0
 arch/arm/boot/dts/qcom/pm8921.dtsi            | 137 +++++++++++
 .../qcom/{qcom-pm8941.dtsi => pm8941.dtsi}    |   0
 .../qcom/{qcom-pma8084.dtsi => pma8084.dtsi}  |   0
 .../dts/qcom/{qcom-pmx55.dtsi => pmx55.dtsi}  |   0
 .../dts/qcom/{qcom-pmx65.dtsi => pmx65.dtsi}  |   0
 .../dts/qcom/qcom-apq8026-asus-sparrow.dts    |   2 +-
 .../dts/qcom/qcom-apq8026-huawei-sturgeon.dts |   2 +-
 .../boot/dts/qcom/qcom-apq8026-lg-lenok.dts   |   2 +-
 .../qcom-apq8026-samsung-matisse-wifi.dts     |   2 +-
 .../dts/qcom/qcom-apq8060-dragonboard.dts     | 164 ++++++++-----
 .../dts/qcom/qcom-apq8064-asus-nexus7-flo.dts |  70 +++---
 .../boot/dts/qcom/qcom-apq8064-cm-qs600.dts   |  35 ++-
 .../boot/dts/qcom/qcom-apq8064-ifc6410.dts    |  42 ++--
 .../qcom-apq8064-sony-xperia-lagan-yuga.dts   | 111 +++++----
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi      | 201 +---------------
 .../dts/qcom/qcom-apq8074-dragonboard.dts     |  31 ++-
 .../boot/dts/qcom/qcom-apq8084-ifc6540.dts    |   2 +-
 arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts   |   2 +-
 arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi      |   2 +-
 .../qcom/qcom-mdm9615-wp8548-mangoh-green.dts |   4 +-
 .../boot/dts/qcom/qcom-mdm9615-wp8548.dtsi    | 143 +++++++++++-
 arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi      | 183 +--------------
 arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts  |  61 +++--
 arch/arm/boot/dts/qcom/qcom-msm8660.dtsi      | 217 +-----------------
 arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts   |  27 ++-
 .../qcom/qcom-msm8960-samsung-expressatt.dts  |   7 +-
 arch/arm/boot/dts/qcom/qcom-msm8960.dtsi      |  45 +---
 .../qcom-msm8974-lge-nexus5-hammerhead.dts    |  31 ++-
 .../qcom/qcom-msm8974-sony-xperia-rhine.dtsi  |  31 ++-
 arch/arm/boot/dts/qcom/qcom-msm8974.dtsi      |  27 ---
 .../qcom/qcom-msm8974pro-fairphone-fp2.dts    |  31 ++-
 .../qcom/qcom-msm8974pro-oneplus-bacon.dts    |  31 ++-
 .../dts/qcom/qcom-msm8974pro-samsung-klte.dts |  12 +-
 ...-msm8974pro-sony-xperia-shinano-castor.dts |  31 ++-
 arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts     |   2 +-
 arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts     |   2 +-
 .../dts/qcom/qcom-sdx55-telit-fn980-tlb.dts   |   2 +-
 arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts     |   2 +-
 46 files changed, 1171 insertions(+), 974 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8921-keypad.yaml
 delete mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
 create mode 100644 arch/arm/boot/dts/qcom/pm8018.dtsi
 create mode 100644 arch/arm/boot/dts/qcom/pm8058.dtsi
 rename arch/arm/boot/dts/qcom/{qcom-pm8226.dtsi => pm8226.dtsi} (100%)
 create mode 100644 arch/arm/boot/dts/qcom/pm8821.dtsi
 rename arch/arm/boot/dts/qcom/{qcom-pm8841.dtsi => pm8841.dtsi} (100%)
 create mode 100644 arch/arm/boot/dts/qcom/pm8921.dtsi
 rename arch/arm/boot/dts/qcom/{qcom-pm8941.dtsi => pm8941.dtsi} (100%)
 rename arch/arm/boot/dts/qcom/{qcom-pma8084.dtsi => pma8084.dtsi} (100%)
 rename arch/arm/boot/dts/qcom/{qcom-pmx55.dtsi => pmx55.dtsi} (100%)
 rename arch/arm/boot/dts/qcom/{qcom-pmx65.dtsi => pmx65.dtsi} (100%)

-- 
2.39.2

[PATCH v4 01/38] dt-bindings: input: qcom,pm8921-keypad: convert to YAML format

[Dmitry Baryshkov]

Convert the bindings for the keypad subdevices of Qualcomm PM8921 and
PM8058 PMICs from text to YAML format.

While doing the conversion also drop the linux,keypad-no-autorepeat
The property was never used by DT files. Both input and DT binding
maintainers consider that bindings should switch to assertive
(linux,autorepeat) instead of negating (no-autorepeat) property.

Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../bindings/input/qcom,pm8921-keypad.yaml    | 89 ++++++++++++++++++
 .../bindings/input/qcom,pm8xxx-keypad.txt     | 90 -------------------
 2 files changed, 89 insertions(+), 90 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8921-keypad.yaml
 delete mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt

diff --git a/Documentation/devicetree/bindings/input/qcom,pm8921-keypad.yaml b/Documentation/devicetree/bindings/input/qcom,pm8921-keypad.yaml
new file mode 100644
index 000000000000..88764adcd696
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8921-keypad.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/qcom,pm8921-keypad.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm PM8921 PMIC KeyPad
+
+maintainers:
+  - Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
+
+allOf:
+  - $ref: input.yaml#
+  - $ref: matrix-keymap.yaml#
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm8058-keypad
+      - qcom,pm8921-keypad
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    items:
+      - description: key sense
+      - description: key stuck
+
+  wakeup-source:
+    type: boolean
+    description: use any event on keypad as wakeup event
+
+  linux,keypad-wakeup:
+    type: boolean
+    deprecated: true
+    description: legacy version of the wakeup-source property
+
+  debounce:
+    description:
+      Time in microseconds that key must be pressed or
+      released for state change interrupt to trigger.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  scan-delay:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: time in microseconds to pause between successive scans of the
+      matrix array
+
+  row-hold:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: time in nanoseconds to pause between scans of each row in the
+      matrix array.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - linux,keymap
+
+unevaluatedProperties: false
+
+examples:
+  - |
+   #include <dt-bindings/input/input.h>
+   #include <dt-bindings/interrupt-controller/irq.h>
+   pmic {
+       #address-cells = <1>;
+       #size-cells = <0>;
+
+       keypad@148 {
+           compatible = "qcom,pm8921-keypad";
+           reg = <0x148>;
+           interrupt-parent = <&pmicintc>;
+           interrupts = <74 IRQ_TYPE_EDGE_RISING>, <75 IRQ_TYPE_EDGE_RISING>;
+           linux,keymap = <
+               MATRIX_KEY(0, 0, KEY_VOLUMEUP)
+               MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
+               MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
+               MATRIX_KEY(0, 3, KEY_CAMERA)
+           >;
+           keypad,num-rows = <1>;
+           keypad,num-columns = <5>;
+           debounce = <15>;
+           scan-delay = <32>;
+           row-hold = <91500>;
+       };
+   };
+...
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
deleted file mode 100644
index 4a9dc6ba96b1..000000000000
--- a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
+++ /dev/null
@@ -1,90 +0,0 @@
-Qualcomm PM8xxx PMIC Keypad
-
-PROPERTIES
-
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: must be one of:
-		    "qcom,pm8058-keypad"
-		    "qcom,pm8921-keypad"
-
-- reg:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: address of keypad control register
-
-- interrupts:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: the first interrupt specifies the key sense interrupt
-		    and the second interrupt specifies the key stuck interrupt.
-		    The format of the specifier is defined by the binding
-		    document describing the node's interrupt parent.
-
-- linux,keymap:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: the linux keymap. More information can be found in
-		    input/matrix-keymap.txt.
-
-- linux,keypad-no-autorepeat:
-	Usage: optional
-	Value type: <bool>
-	Definition: don't enable autorepeat feature.
-
-- wakeup-source:
-	Usage: optional
-	Value type: <bool>
-	Definition: use any event on keypad as wakeup event.
-		    (Legacy property supported: "linux,keypad-wakeup")
-
-- keypad,num-rows:
-	Usage: required
-	Value type: <u32>
-	Definition: number of rows in the keymap. More information can be found
-		    in input/matrix-keymap.txt.
-
-- keypad,num-columns:
-	Usage: required
-	Value type: <u32>
-	Definition: number of columns in the keymap. More information can be
-		    found in input/matrix-keymap.txt.
-
-- debounce:
-	Usage: optional
-	Value type: <u32>
-	Definition: time in microseconds that key must be pressed or release
-		    for key sense interrupt to trigger.
-
-- scan-delay:
-	Usage: optional
-	Value type: <u32>
-	Definition: time in microseconds to pause between successive scans
-		    of the matrix array.
-
-- row-hold:
-	Usage: optional
-	Value type: <u32>
-	Definition: time in nanoseconds to pause between scans of each row in
-		    the matrix array.
-
-EXAMPLE
-
-	keypad@148 {
-		compatible = "qcom,pm8921-keypad";
-		reg = <0x148>;
-		interrupt-parent = <&pmicintc>;
-		interrupts = <74 1>, <75 1>;
-		linux,keymap = <
-			MATRIX_KEY(0, 0, KEY_VOLUMEUP)
-			MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
-			MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
-			MATRIX_KEY(0, 3, KEY_CAMERA)
-			>;
-		keypad,num-rows = <1>;
-		keypad,num-columns = <5>;
-		debounce = <15>;
-		scan-delay = <32>;
-		row-hold = <91500>;
-	};
-- 
2.39.2

[PATCH v4 02/38] dt-bindings: mfd: qcom-pm8xxx: add missing child nodes

[Dmitry Baryshkov]

Add gpio, keypad, led, mpps, pwrkey, vibrator and xoadc as possible
child nodes of qcom,pm8xxx, referencing existint schema files.

Cc: Lee Jones <lee@kernel.org>
Cc: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../devicetree/bindings/mfd/qcom-pm8xxx.yaml  | 26 ++++++++++++++++++-
 1 file changed, 25 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
index 9c51c1b19067..7fe3875a5996 100644
--- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
+++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
@@ -43,13 +43,37 @@ properties:
   interrupt-controller: true
 
 patternProperties:
+  "gpio@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/pinctrl/qcom,pmic-gpio.yaml#
+
+  "keypad@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/input/qcom,pm8921-keypad.yaml#
+
   "led@[0-9a-f]+$":
     type: object
     $ref: /schemas/leds/qcom,pm8058-led.yaml#
 
+  "mpps@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/pinctrl/qcom,pmic-mpp.yaml#
+
+  "pwrkey@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/input/qcom,pm8921-pwrkey.yaml#
+
   "rtc@[0-9a-f]+$":
     type: object
-    $ref: ../rtc/qcom-pm8xxx-rtc.yaml
+    $ref: /schemas/rtc/qcom-pm8xxx-rtc.yaml#
+
+  "vibrator@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/input/qcom,pm8xxx-vib.yaml#
+
+  "xoadc@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/iio/adc/qcom,pm8018-adc.yaml#
 
 required:
   - compatible
-- 
2.39.2

[PATCH v4 03/38] dt-bindings: mfd: qcom-pm8xxx: allow using interrupts-extended

[Dmitry Baryshkov]

Allow using interrupts-extended, which is a preferred form of interrupts
specification compared to the interrupt-parrent + interrupts pair.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
index 7fe3875a5996..33d9615e63c8 100644
--- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
+++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
@@ -37,6 +37,9 @@ properties:
   interrupts:
     maxItems: 1
 
+  interrupts-extended:
+    maxItems: 1
+
   '#interrupt-cells':
     const: 2
 
@@ -75,11 +78,16 @@ patternProperties:
     type: object
     $ref: /schemas/iio/adc/qcom,pm8018-adc.yaml#
 
+oneOf:
+  - required:
+      - interrupts
+  - required:
+      - interrupts-extended
+
 required:
   - compatible
   - '#address-cells'
   - '#size-cells'
-  - interrupts
   - '#interrupt-cells'
   - interrupt-controller
 
-- 
2.39.2

Re: [PATCH v4 03/38] dt-bindings: mfd: qcom-pm8xxx: allow using interrupts-extended

[Krzysztof Kozlowski]

On 27/08/2023 02:58, Dmitry Baryshkov wrote:
> Allow using interrupts-extended, which is a preferred form of interrupts
> specification compared to the interrupt-parrent + interrupts pair.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml | 10 +++++++++-
>  1 file changed, 9 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> index 7fe3875a5996..33d9615e63c8 100644
> --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> @@ -37,6 +37,9 @@ properties:
>    interrupts:
>      maxItems: 1
>  
> +  interrupts-extended:
> +    maxItems: 1

The entire patch is not needed. At least should not be needed. What
problem are you trying to solve here?


Best regards,
Krzysztof

Re: [PATCH v4 03/38] dt-bindings: mfd: qcom-pm8xxx: allow using interrupts-extended

[Dmitry Baryshkov]

On Sun, 27 Aug 2023 at 11:35, Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
>
> On 27/08/2023 02:58, Dmitry Baryshkov wrote:
> > Allow using interrupts-extended, which is a preferred form of interrupts
> > specification compared to the interrupt-parrent + interrupts pair.
> >
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> >  Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml | 10 +++++++++-
> >  1 file changed, 9 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> > index 7fe3875a5996..33d9615e63c8 100644
> > --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> > +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> > @@ -37,6 +37,9 @@ properties:
> >    interrupts:
> >      maxItems: 1
> >
> > +  interrupts-extended:
> > +    maxItems: 1
>
> The entire patch is not needed. At least should not be needed. What
> problem are you trying to solve here?

The main problem is the next chunk, which (currently) explicitly
requires `interrupts' property. My goal is to allow
`interrupts-extended' in addition to `interrupts'.


-- 
With best wishes
Dmitry

Re: [PATCH v4 03/38] dt-bindings: mfd: qcom-pm8xxx: allow using interrupts-extended

[Krzysztof Kozlowski]

On 27/08/2023 12:42, Dmitry Baryshkov wrote:
> On Sun, 27 Aug 2023 at 11:35, Krzysztof Kozlowski
> <krzysztof.kozlowski@linaro.org> wrote:
>>
>> On 27/08/2023 02:58, Dmitry Baryshkov wrote:
>>> Allow using interrupts-extended, which is a preferred form of interrupts
>>> specification compared to the interrupt-parrent + interrupts pair.
>>>
>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>>> ---
>>>  Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml | 10 +++++++++-
>>>  1 file changed, 9 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
>>> index 7fe3875a5996..33d9615e63c8 100644
>>> --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
>>> +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
>>> @@ -37,6 +37,9 @@ properties:
>>>    interrupts:
>>>      maxItems: 1
>>>
>>> +  interrupts-extended:
>>> +    maxItems: 1
>>
>> The entire patch is not needed. At least should not be needed. What
>> problem are you trying to solve here?
> 
> The main problem is the next chunk, which (currently) explicitly
> requires `interrupts' property. My goal is to allow
> `interrupts-extended' in addition to `interrupts'.

They are allowed. Why do you think they aren't? That's why I don't
understand what real problem is here.

Best regards,
Krzysztof

Re: [PATCH v4 03/38] dt-bindings: mfd: qcom-pm8xxx: allow using interrupts-extended

[Dmitry Baryshkov]

On Sun, 27 Aug 2023 at 14:12, Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
>
> On 27/08/2023 12:42, Dmitry Baryshkov wrote:
> > On Sun, 27 Aug 2023 at 11:35, Krzysztof Kozlowski
> > <krzysztof.kozlowski@linaro.org> wrote:
> >>
> >> On 27/08/2023 02:58, Dmitry Baryshkov wrote:
> >>> Allow using interrupts-extended, which is a preferred form of interrupts
> >>> specification compared to the interrupt-parrent + interrupts pair.
> >>>
> >>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> >>> ---
> >>>  Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml | 10 +++++++++-
> >>>  1 file changed, 9 insertions(+), 1 deletion(-)
> >>>
> >>> diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> >>> index 7fe3875a5996..33d9615e63c8 100644
> >>> --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> >>> +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> >>> @@ -37,6 +37,9 @@ properties:
> >>>    interrupts:
> >>>      maxItems: 1
> >>>
> >>> +  interrupts-extended:
> >>> +    maxItems: 1
> >>
> >> The entire patch is not needed. At least should not be needed. What
> >> problem are you trying to solve here?
> >
> > The main problem is the next chunk, which (currently) explicitly
> > requires `interrupts' property. My goal is to allow
> > `interrupts-extended' in addition to `interrupts'.
>
> They are allowed. Why do you think they aren't? That's why I don't
> understand what real problem is here.

qcom-pm8xxx.yaml lists `interrupts' property under the `required'
clause. So I can not simply replace it with `interrupts-extended'


-- 
With best wishes
Dmitry

Re: [PATCH v4 03/38] dt-bindings: mfd: qcom-pm8xxx: allow using interrupts-extended

[Krzysztof Kozlowski]

On 27/08/2023 13:48, Dmitry Baryshkov wrote:
> On Sun, 27 Aug 2023 at 14:12, Krzysztof Kozlowski
> <krzysztof.kozlowski@linaro.org> wrote:
>>
>> On 27/08/2023 12:42, Dmitry Baryshkov wrote:
>>> On Sun, 27 Aug 2023 at 11:35, Krzysztof Kozlowski
>>> <krzysztof.kozlowski@linaro.org> wrote:
>>>>
>>>> On 27/08/2023 02:58, Dmitry Baryshkov wrote:
>>>>> Allow using interrupts-extended, which is a preferred form of interrupts
>>>>> specification compared to the interrupt-parrent + interrupts pair.
>>>>>
>>>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>>>>> ---
>>>>>  Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml | 10 +++++++++-
>>>>>  1 file changed, 9 insertions(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
>>>>> index 7fe3875a5996..33d9615e63c8 100644
>>>>> --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
>>>>> +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
>>>>> @@ -37,6 +37,9 @@ properties:
>>>>>    interrupts:
>>>>>      maxItems: 1
>>>>>
>>>>> +  interrupts-extended:
>>>>> +    maxItems: 1
>>>>
>>>> The entire patch is not needed. At least should not be needed. What
>>>> problem are you trying to solve here?
>>>
>>> The main problem is the next chunk, which (currently) explicitly
>>> requires `interrupts' property. My goal is to allow
>>> `interrupts-extended' in addition to `interrupts'.
>>
>> They are allowed. Why do you think they aren't? That's why I don't
>> understand what real problem is here.
> 
> qcom-pm8xxx.yaml lists `interrupts' property under the `required'
> clause. So I can not simply replace it with `interrupts-extended'

Since when? So again: The entire patch is not needed.


Best regards,
Krzysztof

Re: [PATCH v4 03/38] dt-bindings: mfd: qcom-pm8xxx: allow using interrupts-extended

[Dmitry Baryshkov]

On Sun, 27 Aug 2023 at 15:00, Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
>
> On 27/08/2023 13:48, Dmitry Baryshkov wrote:
> > On Sun, 27 Aug 2023 at 14:12, Krzysztof Kozlowski
> > <krzysztof.kozlowski@linaro.org> wrote:
> >>
> >> On 27/08/2023 12:42, Dmitry Baryshkov wrote:
> >>> On Sun, 27 Aug 2023 at 11:35, Krzysztof Kozlowski
> >>> <krzysztof.kozlowski@linaro.org> wrote:
> >>>>
> >>>> On 27/08/2023 02:58, Dmitry Baryshkov wrote:
> >>>>> Allow using interrupts-extended, which is a preferred form of interrupts
> >>>>> specification compared to the interrupt-parrent + interrupts pair.
> >>>>>
> >>>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> >>>>> ---
> >>>>>  Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml | 10 +++++++++-
> >>>>>  1 file changed, 9 insertions(+), 1 deletion(-)
> >>>>>
> >>>>> diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> >>>>> index 7fe3875a5996..33d9615e63c8 100644
> >>>>> --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> >>>>> +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.yaml
> >>>>> @@ -37,6 +37,9 @@ properties:
> >>>>>    interrupts:
> >>>>>      maxItems: 1
> >>>>>
> >>>>> +  interrupts-extended:
> >>>>> +    maxItems: 1
> >>>>
> >>>> The entire patch is not needed. At least should not be needed. What
> >>>> problem are you trying to solve here?
> >>>
> >>> The main problem is the next chunk, which (currently) explicitly
> >>> requires `interrupts' property. My goal is to allow
> >>> `interrupts-extended' in addition to `interrupts'.
> >>
> >> They are allowed. Why do you think they aren't? That's why I don't
> >> understand what real problem is here.
> >
> > qcom-pm8xxx.yaml lists `interrupts' property under the `required'
> > clause. So I can not simply replace it with `interrupts-extended'
>
> Since when? So again: The entire patch is not needed.

Hmm, interesting. I'm pretty sure that I saw the issue, but now I can
no longer reproduce it. Maybe I misinterpreted some other warning
which I saw while this was WIP.
I see that it is handled by the `fixup_interrupts` in dtschema itself.

-- 
With best wishes
Dmitry

Re: [PATCH v4 03/38] dt-bindings: mfd: qcom-pm8xxx: allow using interrupts-extended

[Krzysztof Kozlowski]

On 27/08/2023 14:57, Dmitry Baryshkov wrote:

>>>>>>
>>>>>> The entire patch is not needed. At least should not be needed. What
>>>>>> problem are you trying to solve here?
>>>>>
>>>>> The main problem is the next chunk, which (currently) explicitly
>>>>> requires `interrupts' property. My goal is to allow
>>>>> `interrupts-extended' in addition to `interrupts'.
>>>>
>>>> They are allowed. Why do you think they aren't? That's why I don't
>>>> understand what real problem is here.
>>>
>>> qcom-pm8xxx.yaml lists `interrupts' property under the `required'
>>> clause. So I can not simply replace it with `interrupts-extended'
>>
>> Since when? So again: The entire patch is not needed.
> 
> Hmm, interesting. I'm pretty sure that I saw the issue, but now I can
> no longer reproduce it. Maybe I misinterpreted some other warning
> which I saw while this was WIP.
> I see that it is handled by the `fixup_interrupts` in dtschema itself.

If interrupts were brought by some other schema and that one did not
evaluate, then you could see errors about interrupt-extended. But that's
not the case here.

Best regards,
Krzysztof

[PATCH v4 04/38] ARM: dts: qcom: apq8064: correct XOADC register address

[Dmitry Baryshkov]

The XOADC is present at the address 0x197 rather than just 197. It
doesn't change a lot (since the driver hardcodes all register
addresses), but the DT should present correct address anyway.

Fixes: c4b70883ee33 ("ARM: dts: add XOADC and IIO HWMON to APQ8064")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index 516f0d2495e2..950adb63af70 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -738,7 +738,7 @@ pwrkey@1c {
 
 				xoadc: xoadc@197 {
 					compatible = "qcom,pm8921-adc";
-					reg = <197>;
+					reg = <0x197>;
 					interrupts-extended = <&pmicintc 78 IRQ_TYPE_EDGE_RISING>;
 					#address-cells = <2>;
 					#size-cells = <0>;
-- 
2.39.2

[PATCH v4 05/38] ARM: dts: qcom: msm8960: introduce label for PMIC keypad

[Dmitry Baryshkov]

To simplify MSM8960 CDP board file, add label to PMIC keypad node.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts | 20 +++++++++-----------
 arch/arm/boot/dts/qcom/qcom-msm8960.dtsi    |  2 +-
 2 files changed, 10 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
index 6c1bc3818883..4641b4f2195d 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
@@ -88,17 +88,15 @@ clk-pins {
 	};
 };
 
-&pmicintc {
-	keypad@148 {
-		linux,keymap = <
-			MATRIX_KEY(0, 0, KEY_VOLUMEUP)
-			MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
-			MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
-			MATRIX_KEY(0, 3, KEY_CAMERA)
-			>;
-		keypad,num-rows = <1>;
-		keypad,num-columns = <5>;
-	};
+&pm8921_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_VOLUMEUP)
+		MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
+		MATRIX_KEY(0, 3, KEY_CAMERA)
+		>;
+	keypad,num-rows = <1>;
+	keypad,num-columns = <5>;
 };
 
 &rpm {
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
index d13080fcbeea..a34fda93d6a4 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -283,7 +283,7 @@ pwrkey@1c {
 					pull-up;
 				};
 
-				keypad@148 {
+				pm8921_keypad: keypad@148 {
 					compatible = "qcom,pm8921-keypad";
 					reg = <0x148>;
 					interrupt-parent = <&pmicintc>;
-- 
2.39.2

[PATCH v4 06/38] ARM: dts: qcom: msm8660-surf: use keypad label directly

[Dmitry Baryshkov]

Directly use pm8058_keypad to declare keypad properties instead of
referencing pm8058 top-level node.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts | 50 ++++++++++----------
 1 file changed, 24 insertions(+), 26 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
index be18f1be29a1..86fbb6dfdc2a 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
@@ -34,32 +34,30 @@ &gsbi12_serial {
 	status = "okay";
 };
 
-&pm8058 {
-	keypad@148 {
-		linux,keymap = <
-			MATRIX_KEY(0, 0, KEY_FN_F1)
-			MATRIX_KEY(0, 1, KEY_UP)
-			MATRIX_KEY(0, 2, KEY_LEFT)
-			MATRIX_KEY(0, 3, KEY_VOLUMEUP)
-			MATRIX_KEY(1, 0, KEY_FN_F2)
-			MATRIX_KEY(1, 1, KEY_RIGHT)
-			MATRIX_KEY(1, 2, KEY_DOWN)
-			MATRIX_KEY(1, 3, KEY_VOLUMEDOWN)
-			MATRIX_KEY(2, 3, KEY_ENTER)
-			MATRIX_KEY(4, 0, KEY_CAMERA_FOCUS)
-			MATRIX_KEY(4, 1, KEY_UP)
-			MATRIX_KEY(4, 2, KEY_LEFT)
-			MATRIX_KEY(4, 3, KEY_HOME)
-			MATRIX_KEY(4, 4, KEY_FN_F3)
-			MATRIX_KEY(5, 0, KEY_CAMERA)
-			MATRIX_KEY(5, 1, KEY_RIGHT)
-			MATRIX_KEY(5, 2, KEY_DOWN)
-			MATRIX_KEY(5, 3, KEY_BACK)
-			MATRIX_KEY(5, 4, KEY_MENU)
-			>;
-		keypad,num-rows = <6>;
-		keypad,num-columns = <5>;
-	};
+&pm8058_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_FN_F1)
+		MATRIX_KEY(0, 1, KEY_UP)
+		MATRIX_KEY(0, 2, KEY_LEFT)
+		MATRIX_KEY(0, 3, KEY_VOLUMEUP)
+		MATRIX_KEY(1, 0, KEY_FN_F2)
+		MATRIX_KEY(1, 1, KEY_RIGHT)
+		MATRIX_KEY(1, 2, KEY_DOWN)
+		MATRIX_KEY(1, 3, KEY_VOLUMEDOWN)
+		MATRIX_KEY(2, 3, KEY_ENTER)
+		MATRIX_KEY(4, 0, KEY_CAMERA_FOCUS)
+		MATRIX_KEY(4, 1, KEY_UP)
+		MATRIX_KEY(4, 2, KEY_LEFT)
+		MATRIX_KEY(4, 3, KEY_HOME)
+		MATRIX_KEY(4, 4, KEY_FN_F3)
+		MATRIX_KEY(5, 0, KEY_CAMERA)
+		MATRIX_KEY(5, 1, KEY_RIGHT)
+		MATRIX_KEY(5, 2, KEY_DOWN)
+		MATRIX_KEY(5, 3, KEY_BACK)
+		MATRIX_KEY(5, 4, KEY_MENU)
+		>;
+	keypad,num-rows = <6>;
+	keypad,num-columns = <5>;
 };
 
 /* eMMC */
-- 
2.39.2

[PATCH v4 07/38] ARM: dts: qcom: apq8064-nexus7: move sdcc1 node to proper place

[Dmitry Baryshkov]

Move sdcc1 device node to follow the alphanumberic sorting order.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
index c57c27cd8a20..0e80a5a8e3c6 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
@@ -181,13 +181,6 @@ &mdp {
 	status = "okay";
 };
 
-/* eMMC */
-&sdcc1 {
-	vmmc-supply = <&pm8921_l5>;
-	vqmmc-supply = <&pm8921_s4>;
-	status = "okay";
-};
-
 &mdp_dsi1_out {
 	remote-endpoint = <&dsi0_in>;
 };
@@ -336,6 +329,13 @@ lvs7 {
 	};
 };
 
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
 &usb_hs1_phy {
 	v3p3-supply = <&pm8921_l3>;
 	v1p8-supply = <&pm8921_l4>;
-- 
2.39.2

[PATCH v4 08/38] ARM: dts: qcom: mdm9615-wp8548-mangoh-green: group include clauses

[Dmitry Baryshkov]

Group file inclusion to follow contemporary practice.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts
index b269fdca1460..e3b4b93c3d38 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts
@@ -6,11 +6,11 @@
  * Author : Neil Armstrong <narmstrong@baylibre.com>
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 #include "qcom-mdm9615-wp8548.dtsi"
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "MangOH Green with WP8548 Module";
-- 
2.39.2

[PATCH v4 09/38] ARM: dts: qcom: strip prefix from PMIC files

[Dmitry Baryshkov]

As the vendor DTS files were moved to per-vendor subdirs, there no need
to use common prefixes. Drop the `qcom-' prefix from PMIC dtsi file.
This makes 32-bit qcom/ dts files closer to arm64 ones.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/{qcom-pm8226.dtsi => pm8226.dtsi}      | 0
 arch/arm/boot/dts/qcom/{qcom-pm8841.dtsi => pm8841.dtsi}      | 0
 arch/arm/boot/dts/qcom/{qcom-pm8941.dtsi => pm8941.dtsi}      | 0
 arch/arm/boot/dts/qcom/{qcom-pma8084.dtsi => pma8084.dtsi}    | 0
 arch/arm/boot/dts/qcom/{qcom-pmx55.dtsi => pmx55.dtsi}        | 0
 arch/arm/boot/dts/qcom/{qcom-pmx65.dtsi => pmx65.dtsi}        | 0
 arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts          | 2 +-
 arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts       | 2 +-
 arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts              | 2 +-
 arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts  | 2 +-
 arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts           | 4 ++--
 arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts               | 2 +-
 arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts                   | 2 +-
 arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts | 4 ++--
 arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi    | 4 ++--
 arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts      | 4 ++--
 arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts      | 4 ++--
 arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts       | 2 +-
 .../dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts   | 4 ++--
 arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts                     | 2 +-
 arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts                     | 2 +-
 arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts         | 2 +-
 arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts                     | 2 +-
 23 files changed, 23 insertions(+), 23 deletions(-)
 rename arch/arm/boot/dts/qcom/{qcom-pm8226.dtsi => pm8226.dtsi} (100%)
 rename arch/arm/boot/dts/qcom/{qcom-pm8841.dtsi => pm8841.dtsi} (100%)
 rename arch/arm/boot/dts/qcom/{qcom-pm8941.dtsi => pm8941.dtsi} (100%)
 rename arch/arm/boot/dts/qcom/{qcom-pma8084.dtsi => pma8084.dtsi} (100%)
 rename arch/arm/boot/dts/qcom/{qcom-pmx55.dtsi => pmx55.dtsi} (100%)
 rename arch/arm/boot/dts/qcom/{qcom-pmx65.dtsi => pmx65.dtsi} (100%)

diff --git a/arch/arm/boot/dts/qcom/qcom-pm8226.dtsi b/arch/arm/boot/dts/qcom/pm8226.dtsi
similarity index 100%
rename from arch/arm/boot/dts/qcom/qcom-pm8226.dtsi
rename to arch/arm/boot/dts/qcom/pm8226.dtsi
diff --git a/arch/arm/boot/dts/qcom/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom/pm8841.dtsi
similarity index 100%
rename from arch/arm/boot/dts/qcom/qcom-pm8841.dtsi
rename to arch/arm/boot/dts/qcom/pm8841.dtsi
diff --git a/arch/arm/boot/dts/qcom/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom/pm8941.dtsi
similarity index 100%
rename from arch/arm/boot/dts/qcom/qcom-pm8941.dtsi
rename to arch/arm/boot/dts/qcom/pm8941.dtsi
diff --git a/arch/arm/boot/dts/qcom/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom/pma8084.dtsi
similarity index 100%
rename from arch/arm/boot/dts/qcom/qcom-pma8084.dtsi
rename to arch/arm/boot/dts/qcom/pma8084.dtsi
diff --git a/arch/arm/boot/dts/qcom/qcom-pmx55.dtsi b/arch/arm/boot/dts/qcom/pmx55.dtsi
similarity index 100%
rename from arch/arm/boot/dts/qcom/qcom-pmx55.dtsi
rename to arch/arm/boot/dts/qcom/pmx55.dtsi
diff --git a/arch/arm/boot/dts/qcom/qcom-pmx65.dtsi b/arch/arm/boot/dts/qcom/pmx65.dtsi
similarity index 100%
rename from arch/arm/boot/dts/qcom/qcom-pmx65.dtsi
rename to arch/arm/boot/dts/qcom/pmx65.dtsi
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts
index aa0e0e8d2a97..a39f5a161b03 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts
@@ -6,7 +6,7 @@
 /dts-v1/;
 
 #include "qcom-msm8226.dtsi"
-#include "qcom-pm8226.dtsi"
+#include "pm8226.dtsi"
 
 /delete-node/ &adsp_region;
 
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts
index de19640efe55..59b218042d32 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts
@@ -6,7 +6,7 @@
 /dts-v1/;
 
 #include "qcom-msm8226.dtsi"
-#include "qcom-pm8226.dtsi"
+#include "pm8226.dtsi"
 #include <dt-bindings/input/ti-drv260x.h>
 
 /delete-node/ &adsp_region;
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts
index b887e5361ec3..feb78afef3a6 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts
@@ -6,7 +6,7 @@
 /dts-v1/;
 
 #include "qcom-msm8226.dtsi"
-#include "qcom-pm8226.dtsi"
+#include "pm8226.dtsi"
 
 /delete-node/ &adsp_region;
 
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
index 884d99297d4c..42d3867dca42 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
@@ -7,7 +7,7 @@
 
 #include <dt-bindings/input/input.h>
 #include "qcom-msm8226.dtsi"
-#include "qcom-pm8226.dtsi"
+#include "pm8226.dtsi"
 
 /delete-node/ &adsp_region;
 /delete-node/ &smem_region;
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
index 6d1b2439ae3a..950fa652f985 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
@@ -4,8 +4,8 @@
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
 
 /delete-node/ &mpss_region;
 
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts
index 116e59a3b76d..1df24c922be9 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-apq8084.dtsi"
-#include "qcom-pma8084.dtsi"
+#include "pma8084.dtsi"
 
 / {
 	model = "Qualcomm APQ8084/IFC6540";
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts b/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts
index c6b6680248a6..d4e6aee034af 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-apq8084.dtsi"
-#include "qcom-pma8084.dtsi"
+#include "pma8084.dtsi"
 
 / {
 	model = "Qualcomm APQ 8084-MTP";
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
index 60bdfddeae69..da99f770d4f5 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
index 68a2f9094e53..23ae474698aa 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
index 42d253b75dad..6c4153689b39 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-msm8974pro.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
index 8230d0e1d95d..c0ca264d8140 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-msm8974pro.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
index 3e2c86591ee2..325feb89b343 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-msm8974pro.dtsi"
-#include "qcom-pma8084.dtsi"
+#include "pma8084.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/leds/common.h>
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
index 11468d1409f7..0798cce3dbea 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-msm8974pro.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts
index 7e97ad5803d8..247069361909 100644
--- a/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts
@@ -9,7 +9,7 @@
 #include "qcom-sdx55.dtsi"
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include <arm64/qcom/pm8150b.dtsi>
-#include "qcom-pmx55.dtsi"
+#include "pmx55.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SDX55 MTP";
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
index 51058b065279..082f7ed1a01f 100644
--- a/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
@@ -8,7 +8,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "qcom-sdx55.dtsi"
-#include "qcom-pmx55.dtsi"
+#include "pmx55.dtsi"
 
 / {
 	model = "Thundercomm T55 Development Kit";
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts
index 8fadc6e70692..e336a15b45c4 100644
--- a/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts
@@ -8,7 +8,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "qcom-sdx55.dtsi"
-#include "qcom-pmx55.dtsi"
+#include "pmx55.dtsi"
 
 / {
 	model = "Telit FN980 TLB";
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
index fcf1c51c5e7a..b87c5434cc29 100644
--- a/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
@@ -8,7 +8,7 @@
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include <arm64/qcom/pmk8350.dtsi>
 #include <arm64/qcom/pm7250b.dtsi>
-#include "qcom-pmx65.dtsi"
+#include "pmx65.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SDX65 MTP";
-- 
2.39.2

[PATCH v4 10/38] ARM: dts: qcom: apq8064: fix PMIC node labels

[Dmitry Baryshkov]

Change PM8921 node labels to start with pm8921_ prefix, following other
Qualcomm PMIC device nodes.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index 950adb63af70..6514d728b1ec 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -292,13 +292,13 @@ scm {
 	 */
 	iio-hwmon {
 		compatible = "iio-hwmon";
-		io-channels = <&xoadc 0x00 0x01>, /* Battery */
-			    <&xoadc 0x00 0x02>, /* DC in (charger) */
-			    <&xoadc 0x00 0x04>, /* VPH the main system voltage */
-			    <&xoadc 0x00 0x0b>, /* Die temperature */
-			    <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
-			    <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
-			    <&xoadc 0x00 0x0e>; /* Charger temperature */
+		io-channels = <&pm8921_xoadc 0x00 0x01>, /* Battery */
+			      <&pm8921_xoadc 0x00 0x02>, /* DC in (charger) */
+			      <&pm8921_xoadc 0x00 0x04>, /* VPH the main system voltage */
+			      <&pm8921_xoadc 0x00 0x0b>, /* Die temperature */
+			      <&pm8921_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			      <&pm8921_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			      <&pm8921_xoadc 0x00 0x0e>; /* Charger temperature */
 	};
 
 	soc: soc {
@@ -686,7 +686,7 @@ ssbi@500000 {
 			reg = <0x00500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pmicintc: pmic {
+			pm8921: pmic {
 				compatible = "qcom,pm8921";
 				interrupt-parent = <&tlmm_pinmux>;
 				interrupts = <74 8>;
@@ -721,7 +721,7 @@ pm8921_mpps: mpps@50 {
 
 				rtc@11d {
 					compatible = "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8921>;
 					interrupts = <39 1>;
 					reg = <0x11d>;
 					allow-set-time;
@@ -730,16 +730,16 @@ rtc@11d {
 				pwrkey@1c {
 					compatible = "qcom,pm8921-pwrkey";
 					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8921>;
 					interrupts = <50 1>, <51 1>;
 					debounce = <15625>;
 					pull-up;
 				};
 
-				xoadc: xoadc@197 {
+				pm8921_xoadc: xoadc@197 {
 					compatible = "qcom,pm8921-adc";
 					reg = <0x197>;
-					interrupts-extended = <&pmicintc 78 IRQ_TYPE_EDGE_RISING>;
+					interrupts-extended = <&pm8921 78 IRQ_TYPE_EDGE_RISING>;
 					#address-cells = <2>;
 					#size-cells = <0>;
 					#io-channel-cells = <2>;
-- 
2.39.2

[PATCH v4 11/38] ARM: dts: qcom: mdm9615: fix PMIC node labels

[Dmitry Baryshkov]

Change PM8018 node labels to start with pm8018_ prefix, following other
Qualcomm PMIC device nodes.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi |  2 +-
 arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi        | 14 +++++++-------
 2 files changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
index 92c8003dac25..dac3aa793f71 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
@@ -76,7 +76,7 @@ reset-out-pins {
 	};
 };
 
-&pmicgpio {
+&pm8018_gpio {
 	usb_vbus_5v_pins: usb-vbus-5v-state {
 		pins = "gpio4";
 		function = "normal";
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
index fc4f52f9e9f7..c4cfbdbcdf14 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
@@ -263,7 +263,7 @@ qcom,ssbi@500000 {
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pmicintc: pmic {
+			pm8018: pmic {
 				compatible = "qcom,pm8018", "qcom,pm8921";
 				interrupts = <GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <2>;
@@ -274,38 +274,38 @@ pmicintc: pmic {
 				pwrkey@1c {
 					compatible = "qcom,pm8018-pwrkey", "qcom,pm8921-pwrkey";
 					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8018>;
 					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
 						     <51 IRQ_TYPE_EDGE_RISING>;
 					debounce = <15625>;
 					pull-up;
 				};
 
-				pmicmpp: mpps@50 {
+				pm8018_mpps: mpps@50 {
 					compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
 					interrupt-controller;
 					#interrupt-cells = <2>;
 					reg = <0x50>;
 					gpio-controller;
 					#gpio-cells = <2>;
-					gpio-ranges = <&pmicmpp 0 0 6>;
+					gpio-ranges = <&pm8018_mpps 0 0 6>;
 				};
 
 				rtc@11d {
 					compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8018>;
 					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
 					reg = <0x11d>;
 					allow-set-time;
 				};
 
-				pmicgpio: gpio@150 {
+				pm8018_gpio: gpio@150 {
 					compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio";
 					reg = <0x150>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
 					gpio-controller;
-					gpio-ranges = <&pmicgpio 0 0 6>;
+					gpio-ranges = <&pm8018_gpio 0 0 6>;
 					#gpio-cells = <2>;
 				};
 			};
-- 
2.39.2

[PATCH v4 12/38] ARM: dts: qcom: msm8660: fix PMIC node labels

[Dmitry Baryshkov]

Change PM8058 node labels to start with pm8058_ prefix, following other
Qualcomm PMIC device nodes.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../boot/dts/qcom/qcom-apq8060-dragonboard.dts   |  4 ++--
 arch/arm/boot/dts/qcom/qcom-msm8660.dtsi         | 16 ++++++++--------
 2 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
index db4c791b2e2f..48fd1a1feea3 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
@@ -72,7 +72,7 @@ cm3605 {
 		/* Trig on both edges - getting close or far away */
 		interrupts-extended = <&pm8058_gpio 34 IRQ_TYPE_EDGE_BOTH>;
 		/* MPP05 analog input to the XOADC */
-		io-channels = <&xoadc 0x00 0x05>;
+		io-channels = <&pm8058_xoadc 0x00 0x05>;
 		io-channel-names = "aout";
 		pinctrl-names = "default";
 		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
@@ -945,7 +945,7 @@ irq-pins {
 	};
 };
 
-&xoadc {
+&pm8058_xoadc {
 	/* Reference voltage 2.2 V */
 	xoadc-ref-supply = <&pm8058_l18>;
 
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
index 78023ed2fdf7..9217ced108c4 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
@@ -80,13 +80,13 @@ sleep-clk {
 	 */
 	iio-hwmon {
 		compatible = "iio-hwmon";
-		io-channels = <&xoadc 0x00 0x01>, /* Battery */
-			    <&xoadc 0x00 0x02>, /* DC in (charger) */
-			    <&xoadc 0x00 0x04>, /* VPH the main system voltage */
-			    <&xoadc 0x00 0x0b>, /* Die temperature */
-			    <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
-			    <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
-			    <&xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
+		io-channels = <&pm8058_xoadc 0x00 0x01>, /* Battery */
+			      <&pm8058_xoadc 0x00 0x02>, /* DC in (charger) */
+			      <&pm8058_xoadc 0x00 0x04>, /* VPH the main system voltage */
+			      <&pm8058_xoadc 0x00 0x0b>, /* Die temperature */
+			      <&pm8058_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			      <&pm8058_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			      <&pm8058_xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
 	};
 
 	soc: soc {
@@ -390,7 +390,7 @@ pm8058_keypad: keypad@148 {
 					row-hold = <91500>;
 				};
 
-				xoadc: xoadc@197 {
+				pm8058_xoadc: xoadc@197 {
 					compatible = "qcom,pm8058-adc";
 					reg = <0x197>;
 					interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
-- 
2.39.2

[PATCH v4 13/38] ARM: dts: qcom: msm8960: fix PMIC node labels

[Dmitry Baryshkov]

Change PM8921 node labels to start with pm8921_ prefix, following other
Qualcomm PMIC device nodes.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-msm8960.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
index a34fda93d6a4..ea2d961b266b 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -264,7 +264,7 @@ ssbi@500000 {
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pmicintc: pmic {
+			pm8921: pmic {
 				compatible = "qcom,pm8921";
 				interrupt-parent = <&msmgpio>;
 				interrupts = <104 IRQ_TYPE_LEVEL_LOW>;
@@ -276,7 +276,7 @@ pmicintc: pmic {
 				pwrkey@1c {
 					compatible = "qcom,pm8921-pwrkey";
 					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8921>;
 					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
 						     <51 IRQ_TYPE_EDGE_RISING>;
 					debounce = <15625>;
@@ -286,7 +286,7 @@ pwrkey@1c {
 				pm8921_keypad: keypad@148 {
 					compatible = "qcom,pm8921-keypad";
 					reg = <0x148>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8921>;
 					interrupts = <74 IRQ_TYPE_EDGE_RISING>,
 						     <75 IRQ_TYPE_EDGE_RISING>;
 					debounce = <15>;
@@ -296,7 +296,7 @@ pm8921_keypad: keypad@148 {
 
 				rtc@11d {
 					compatible = "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8921>;
 					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
 					reg = <0x11d>;
 					allow-set-time;
-- 
2.39.2

[PATCH v4 14/38] ARM: dts: qcom: apq8064: move PMIC interrupts to the board files

[Dmitry Baryshkov]

The interrupt of SSBI PMICs is routed to the SoCs GPIO. As such, it is
not a property of the SoC, it is a property of the particular board
(even if it is standard and unified between all devices). Move these
interrupt specifications to the board files.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts   | 8 ++++++++
 arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts          | 8 ++++++++
 arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts           | 8 ++++++++
 .../boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts | 8 ++++++++
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi                  | 4 ----
 5 files changed, 32 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
index 0e80a5a8e3c6..b820f3255c16 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
@@ -185,6 +185,14 @@ &mdp_dsi1_out {
 	remote-endpoint = <&dsi0_in>;
 };
 
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
 &rpm {
 	regulators {
 		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
index d6ecfd8addb7..c01254b1a3a7 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
@@ -69,6 +69,14 @@ &pcie {
 	status = "okay";
 };
 
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
 &pm8921_gpio {
 	wlan_default_gpios: wlan-gpios-state {
 		pinconf {
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
index 96307550523a..f1bd29333c9b 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
@@ -171,6 +171,14 @@ &pcie {
 	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
 };
 
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
 &pm8921_gpio {
 	wlan_default_gpios: wlan-gpios-state {
 		pinconf {
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
index 9244512b74d1..7917f1657025 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
@@ -65,6 +65,14 @@ &gsbi5_serial {
 	status = "okay";
 };
 
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
 &pm8921_gpio {
 	gpio_keys_pin_a: gpio-keys-active-state {
 		pins = "gpio3", "gpio4", "gpio29", "gpio35";
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index 6514d728b1ec..76796002bda6 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -662,8 +662,6 @@ ssbi@c00000 {
 
 			pm8821: pmic {
 				compatible = "qcom,pm8821";
-				interrupt-parent = <&tlmm_pinmux>;
-				interrupts = <76 IRQ_TYPE_LEVEL_LOW>;
 				#interrupt-cells = <2>;
 				interrupt-controller;
 				#address-cells = <1>;
@@ -688,8 +686,6 @@ ssbi@500000 {
 
 			pm8921: pmic {
 				compatible = "qcom,pm8921";
-				interrupt-parent = <&tlmm_pinmux>;
-				interrupts = <74 8>;
 				#interrupt-cells = <2>;
 				interrupt-controller;
 				#address-cells = <1>;
-- 
2.39.2

[PATCH v4 15/38] ARM: dts: qcom: mdm9615: move PMIC interrupts to the board files

[Dmitry Baryshkov]

The interrupt of SSBI PMICs is routed to the SoCs GPIO. As such, it is
not a property of the SoC, it is a property of the particular board
(even if it is standard and unified between all devices). Move these
interrupt specifications to the board files.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi | 4 ++++
 arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi        | 1 -
 2 files changed, 4 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
index dac3aa793f71..b782ff0d16cd 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
@@ -76,6 +76,10 @@ reset-out-pins {
 	};
 };
 
+&pm8018 {
+	interrupts-extended = <&intc GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
+};
+
 &pm8018_gpio {
 	usb_vbus_5v_pins: usb-vbus-5v-state {
 		pins = "gpio4";
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
index c4cfbdbcdf14..373d9425b8bd 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
@@ -265,7 +265,6 @@ qcom,ssbi@500000 {
 
 			pm8018: pmic {
 				compatible = "qcom,pm8018", "qcom,pm8921";
-				interrupts = <GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <2>;
 				interrupt-controller;
 				#address-cells = <1>;
-- 
2.39.2

[PATCH v4 16/38] ARM: dts: qcom: msm8660: move PMIC interrupts to the board files

[Dmitry Baryshkov]

The interrupt of SSBI PMICs is routed to the SoCs GPIO. As such, it is
not a property of the SoC, it is a property of the particular board
(even if it is standard and unified between all devices). Move these
interrupt specifications to the board files.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts | 4 ++++
 arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts        | 4 ++++
 arch/arm/boot/dts/qcom/qcom-msm8660.dtsi            | 2 --
 3 files changed, 8 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
index 48fd1a1feea3..e4261d729d35 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
@@ -273,6 +273,10 @@ kxsd9@18 {
 	};
 };
 
+&pm8058 {
+	interrupts-extended = <&tlmm 88 IRQ_TYPE_LEVEL_LOW>;
+};
+
 &pm8058_gpio {
 	dragon_ethernet_gpios: ethernet-state {
 		pinconf {
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
index 86fbb6dfdc2a..a5441aecd637 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
@@ -34,6 +34,10 @@ &gsbi12_serial {
 	status = "okay";
 };
 
+&pm8058 {
+	interrupts-extended = <&tlmm 88 IRQ_TYPE_LEVEL_LOW>;
+};
+
 &pm8058_keypad {
 	linux,keymap = <
 		MATRIX_KEY(0, 0, KEY_FN_F1)
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
index 9217ced108c4..84b0366792d4 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
@@ -341,8 +341,6 @@ ssbi@500000 {
 
 			pm8058: pmic {
 				compatible = "qcom,pm8058";
-				interrupt-parent = <&tlmm>;
-				interrupts = <88 8>;
 				#interrupt-cells = <2>;
 				interrupt-controller;
 				#address-cells = <1>;
-- 
2.39.2

[PATCH v4 17/38] ARM: dts: qcom: msm8960: move PMIC interrupts to the board files

[Dmitry Baryshkov]

The interrupt of SSBI PMICs is routed to the SoCs GPIO. As such, it is
not a property of the SoC, it is a property of the particular board
(even if it is standard and unified between all devices). Move these
interrupt specifications to the board files.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts                | 4 ++++
 arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts | 4 ++++
 arch/arm/boot/dts/qcom/qcom-msm8960.dtsi                   | 2 --
 3 files changed, 8 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
index 4641b4f2195d..43149c90c4fc 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
@@ -88,6 +88,10 @@ clk-pins {
 	};
 };
 
+&pm8921 {
+	interrupts-extended = <&msmgpio 104 IRQ_TYPE_LEVEL_LOW>;
+};
+
 &pm8921_keypad {
 	linux,keymap = <
 		MATRIX_KEY(0, 0, KEY_VOLUMEUP)
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
index 13e85c287498..9e203164beb6 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
@@ -84,6 +84,10 @@ clk-pins {
 	};
 };
 
+&pm8921 {
+	interrupts-extended = <&msmgpio 104 IRQ_TYPE_LEVEL_LOW>;
+};
+
 &rpm {
 	regulators {
 		compatible = "qcom,rpm-pm8921-regulators";
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
index ea2d961b266b..f1267c83d67a 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -266,8 +266,6 @@ ssbi@500000 {
 
 			pm8921: pmic {
 				compatible = "qcom,pm8921";
-				interrupt-parent = <&msmgpio>;
-				interrupts = <104 IRQ_TYPE_LEVEL_LOW>;
 				#interrupt-cells = <2>;
 				interrupt-controller;
 				#address-cells = <1>;
-- 
2.39.2

[PATCH v4 18/38] ARM: dts: qcom: msm8960: split PMIC to separate dtsi files

[Dmitry Baryshkov]

The PMIC is not a part of the SoC, so move PMIC to a separate file and
include it from the board files.

Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8921.dtsi            | 40 +++++++++++++++++++
 arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts   |  1 +
 .../qcom/qcom-msm8960-samsung-expressatt.dts  |  3 +-
 arch/arm/boot/dts/qcom/qcom-msm8960.dtsi      | 39 +-----------------
 4 files changed, 44 insertions(+), 39 deletions(-)
 create mode 100644 arch/arm/boot/dts/qcom/pm8921.dtsi

diff --git a/arch/arm/boot/dts/qcom/pm8921.dtsi b/arch/arm/boot/dts/qcom/pm8921.dtsi
new file mode 100644
index 000000000000..414941f7a42f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8921.dtsi
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0
+
+&ssbi {
+	pm8921: pmic {
+		compatible = "qcom,pm8921";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pwrkey@1c {
+			compatible = "qcom,pm8921-pwrkey";
+			reg = <0x1c>;
+			interrupt-parent = <&pm8921>;
+			interrupts = <50 IRQ_TYPE_EDGE_RISING>,
+				     <51 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8921_keypad: keypad@148 {
+			compatible = "qcom,pm8921-keypad";
+			reg = <0x148>;
+			interrupt-parent = <&pm8921>;
+			interrupts = <74 IRQ_TYPE_EDGE_RISING>,
+				     <75 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15>;
+			scan-delay = <32>;
+			row-hold = <91500>;
+		};
+
+		rtc@11d {
+			compatible = "qcom,pm8921-rtc";
+			interrupt-parent = <&pm8921>;
+			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
+			reg = <0x11d>;
+			allow-set-time;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
index 43149c90c4fc..a5ea4843db43 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
@@ -2,6 +2,7 @@
 #include <dt-bindings/input/input.h>
 
 #include "qcom-msm8960.dtsi"
+#include "pm8921.dtsi"
 
 / {
 	model = "Qualcomm MSM8960 CDP";
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
index 9e203164beb6..1a5116336ff0 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
@@ -1,8 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
 
 #include "qcom-msm8960.dtsi"
-#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+#include "pm8921.dtsi"
 
 / {
 	model = "Samsung Galaxy Express SGH-I437";
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
index f1267c83d67a..774f507fa25a 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -259,47 +259,10 @@ gsbi5_serial: serial@16440000 {
 			};
 		};
 
-		ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8921: pmic {
-				compatible = "qcom,pm8921";
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pwrkey@1c {
-					compatible = "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pm8921>;
-					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
-						     <51 IRQ_TYPE_EDGE_RISING>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				pm8921_keypad: keypad@148 {
-					compatible = "qcom,pm8921-keypad";
-					reg = <0x148>;
-					interrupt-parent = <&pm8921>;
-					interrupts = <74 IRQ_TYPE_EDGE_RISING>,
-						     <75 IRQ_TYPE_EDGE_RISING>;
-					debounce = <15>;
-					scan-delay = <32>;
-					row-hold = <91500>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8921-rtc";
-					interrupt-parent = <&pm8921>;
-					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-			};
 		};
 
 		rng@1a500000 {
-- 
2.39.2

[PATCH v4 19/38] ARM: dts: qcom: apq8064: split PMICs to separate dtsi files

[Dmitry Baryshkov]

The PMICs are not a part of the SoC, so move PMICs to separate files and
include them from the board files.

Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8821.dtsi            |  22 +++
 arch/arm/boot/dts/qcom/pm8921.dtsi            |  99 +++++++++++++
 .../dts/qcom/qcom-apq8064-asus-nexus7-flo.dts |   6 +-
 .../boot/dts/qcom/qcom-apq8064-cm-qs600.dts   |   5 +-
 .../boot/dts/qcom/qcom-apq8064-ifc6410.dts    |   5 +-
 .../qcom-apq8064-sony-xperia-lagan-yuga.dts   |   5 +-
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi      | 134 +-----------------
 7 files changed, 140 insertions(+), 136 deletions(-)
 create mode 100644 arch/arm/boot/dts/qcom/pm8821.dtsi

diff --git a/arch/arm/boot/dts/qcom/pm8821.dtsi b/arch/arm/boot/dts/qcom/pm8821.dtsi
new file mode 100644
index 000000000000..064e3ba54e18
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8821.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* This PMIC is used on a secondary SSBI bus */
+&ssbi2 {
+	pm8821: pmic {
+		compatible = "qcom,pm8821";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8821_mpps: mpps@50 {
+			compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8821_mpps 0 0 4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/pm8921.dtsi b/arch/arm/boot/dts/qcom/pm8921.dtsi
index 414941f7a42f..ad41d99ab265 100644
--- a/arch/arm/boot/dts/qcom/pm8921.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8921.dtsi
@@ -8,6 +8,30 @@ pm8921: pmic {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8921_gpio: gpio@150 {
+
+			compatible = "qcom,pm8921-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8921_gpio 0 0 44>;
+			#gpio-cells = <2>;
+
+		};
+
+		pm8921_mpps: mpps@50 {
+			compatible = "qcom,pm8921-mpp",
+				     "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8921_mpps 0 0 12>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
 		pwrkey@1c {
 			compatible = "qcom,pm8921-pwrkey";
 			reg = <0x1c>;
@@ -36,5 +60,80 @@ rtc@11d {
 			reg = <0x11d>;
 			allow-set-time;
 		};
+
+		pm8921_xoadc: xoadc@197 {
+			compatible = "qcom,pm8921-adc";
+			reg = <0x197>;
+			interrupts-extended = <&pm8921 78 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			#io-channel-cells = <2>;
+
+			vcoin: adc-channel@0 {
+				reg = <0x00 0x00>;
+			};
+
+			vbat: adc-channel@1 {
+				reg = <0x00 0x01>;
+			};
+
+			dcin: adc-channel@2 {
+				reg = <0x00 0x02>;
+			};
+
+			vph_pwr: adc-channel@4 {
+				reg = <0x00 0x04>;
+			};
+
+			batt_therm: adc-channel@8 {
+				reg = <0x00 0x08>;
+			};
+
+			batt_id: adc-channel@9 {
+				reg = <0x00 0x09>;
+			};
+
+			usb_vbus: adc-channel@a {
+				reg = <0x00 0x0a>;
+			};
+
+			die_temp: adc-channel@b {
+				reg = <0x00 0x0b>;
+			};
+
+			ref_625mv: adc-channel@c {
+				reg = <0x00 0x0c>;
+			};
+
+			ref_1250mv: adc-channel@d {
+				reg = <0x00 0x0d>;
+			};
+
+			chg_temp: adc-channel@e {
+				reg = <0x00 0x0e>;
+			};
+
+			ref_muxoff: adc-channel@f {
+				reg = <0x00 0x0f>;
+			};
+		};
+	};
+};
+
+/ {
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&pm8921_xoadc 0x00 0x01>, /* Battery */
+			      <&pm8921_xoadc 0x00 0x02>, /* DC in (charger) */
+			      <&pm8921_xoadc 0x00 0x04>, /* VPH the main system voltage */
+			      <&pm8921_xoadc 0x00 0x0b>, /* Die temperature */
+			      <&pm8921_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			      <&pm8921_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			      <&pm8921_xoadc 0x00 0x0e>; /* Charger temperature */
 	};
 };
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
index b820f3255c16..d709d6e840ec 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
@@ -1,8 +1,12 @@
 // SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
 / {
 	model = "Asus Nexus7(flo)";
 	compatible = "asus,nexus7-flo", "qcom,apq8064";
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
index c01254b1a3a7..d4db84e9fcf3 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
@@ -1,8 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
 / {
 	model = "CompuLab CM-QS600";
 	compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064";
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
index f1bd29333c9b..5fd84319254e 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
@@ -1,9 +1,12 @@
 // SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
 / {
 	model = "Qualcomm APQ8064/IFC6410";
 	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
index 7917f1657025..ba18a02b1c57 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
@@ -1,10 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/mfd/qcom-rpm.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
 / {
 	model = "Sony Xperia Z";
 	compatible = "sony,xperia-yuga", "qcom,apq8064";
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index 76796002bda6..5704d0598b96 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -284,23 +284,6 @@ scm {
 		};
 	};
 
-
-	/*
-	 * These channels from the ADC are simply hardware monitors.
-	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
-	 * ADC.
-	 */
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&pm8921_xoadc 0x00 0x01>, /* Battery */
-			      <&pm8921_xoadc 0x00 0x02>, /* DC in (charger) */
-			      <&pm8921_xoadc 0x00 0x04>, /* VPH the main system voltage */
-			      <&pm8921_xoadc 0x00 0x0b>, /* Die temperature */
-			      <&pm8921_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
-			      <&pm8921_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
-			      <&pm8921_xoadc 0x00 0x0e>; /* Charger temperature */
-	};
-
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -655,129 +638,16 @@ rng@1a500000 {
 			clock-names = "core";
 		};
 
-		ssbi@c00000 {
+		ssbi2: ssbi@c00000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00c00000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8821: pmic {
-				compatible = "qcom,pm8821";
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8821_mpps: mpps@50 {
-					compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
-					reg = <0x50>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pm8821_mpps 0 0 4>;
-				};
-			};
 		};
 
-		ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8921: pmic {
-				compatible = "qcom,pm8921";
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8921_gpio: gpio@150 {
-
-					compatible = "qcom,pm8921-gpio",
-						     "qcom,ssbi-gpio";
-					reg = <0x150>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pm8921_gpio 0 0 44>;
-					#gpio-cells = <2>;
-
-				};
-
-				pm8921_mpps: mpps@50 {
-					compatible = "qcom,pm8921-mpp",
-						     "qcom,ssbi-mpp";
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pm8921_mpps 0 0 12>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8921-rtc";
-					interrupt-parent = <&pm8921>;
-					interrupts = <39 1>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-
-				pwrkey@1c {
-					compatible = "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pm8921>;
-					interrupts = <50 1>, <51 1>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				pm8921_xoadc: xoadc@197 {
-					compatible = "qcom,pm8921-adc";
-					reg = <0x197>;
-					interrupts-extended = <&pm8921 78 IRQ_TYPE_EDGE_RISING>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-					#io-channel-cells = <2>;
-
-					vcoin: adc-channel@0 {
-						reg = <0x00 0x00>;
-					};
-					vbat: adc-channel@1 {
-						reg = <0x00 0x01>;
-					};
-					dcin: adc-channel@2 {
-						reg = <0x00 0x02>;
-					};
-					vph_pwr: adc-channel@4 {
-						reg = <0x00 0x04>;
-					};
-					batt_therm: adc-channel@8 {
-						reg = <0x00 0x08>;
-					};
-					batt_id: adc-channel@9 {
-						reg = <0x00 0x09>;
-					};
-					usb_vbus: adc-channel@a {
-						reg = <0x00 0x0a>;
-					};
-					die_temp: adc-channel@b {
-						reg = <0x00 0x0b>;
-					};
-					ref_625mv: adc-channel@c {
-						reg = <0x00 0x0c>;
-					};
-					ref_1250mv: adc-channel@d {
-						reg = <0x00 0x0d>;
-					};
-					chg_temp: adc-channel@e {
-						reg = <0x00 0x0e>;
-					};
-					ref_muxoff: adc-channel@f {
-						reg = <0x00 0x0f>;
-					};
-				};
-			};
 		};
 
 		qfprom: qfprom@700000 {
-- 
2.39.2

[PATCH v4 20/38] ARM: dts: qcom: mdm9615: split PMIC to separate dtsi files

[Dmitry Baryshkov]

The PMIC is not a part of the SoC, so move PMIC to a separate file and
include it from the board files.

Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8018.dtsi            | 57 +++++++++++++++++++
 .../boot/dts/qcom/qcom-mdm9615-wp8548.dtsi    |  1 +
 arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi      | 48 +---------------
 3 files changed, 59 insertions(+), 47 deletions(-)
 create mode 100644 arch/arm/boot/dts/qcom/pm8018.dtsi

diff --git a/arch/arm/boot/dts/qcom/pm8018.dtsi b/arch/arm/boot/dts/qcom/pm8018.dtsi
new file mode 100644
index 000000000000..c602544900b2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8018.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for Qualcomm PM8018
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+&ssbi {
+	pm8018: pmic {
+		compatible = "qcom,pm8018", "qcom,pm8921";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pwrkey@1c {
+			compatible = "qcom,pm8018-pwrkey",
+				     "qcom,pm8921-pwrkey";
+			reg = <0x1c>;
+			interrupt-parent = <&pm8018>;
+			interrupts = <50 IRQ_TYPE_EDGE_RISING>,
+				     <51 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8018_mpps: mpps@50 {
+			compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8018_mpps 0 0 6>;
+		};
+
+		rtc@11d {
+			compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
+			interrupt-parent = <&pm8018>;
+			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
+			reg = <0x11d>;
+			allow-set-time;
+		};
+
+		pm8018_gpio: gpio@150 {
+			compatible = "qcom,pm8058-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8018_gpio 0 0 6>;
+			#gpio-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
index b782ff0d16cd..27c3d92d9452 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
@@ -7,6 +7,7 @@
  */
 
 #include "qcom-mdm9615.dtsi"
+#include "pm8018.dtsi"
 
 / {
 	model = "Sierra Wireless WP8548 Module";
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
index 373d9425b8bd..e23ca6c42683 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
@@ -258,56 +258,10 @@ gsbi5_serial: serial@16440000 {
 			};
 		};
 
-		qcom,ssbi@500000 {
+		ssbi: qcom,ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8018: pmic {
-				compatible = "qcom,pm8018", "qcom,pm8921";
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pwrkey@1c {
-					compatible = "qcom,pm8018-pwrkey", "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pm8018>;
-					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
-						     <51 IRQ_TYPE_EDGE_RISING>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				pm8018_mpps: mpps@50 {
-					compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pm8018_mpps 0 0 6>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
-					interrupt-parent = <&pm8018>;
-					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-
-				pm8018_gpio: gpio@150 {
-					compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio";
-					reg = <0x150>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pm8018_gpio 0 0 6>;
-					#gpio-cells = <2>;
-				};
-			};
 		};
 
 		sdcc1bam: dma-controller@12182000 {
-- 
2.39.2

[PATCH v4 21/38] ARM: dts: qcom: msm8660: split PMIC to separate dtsi files

[Dmitry Baryshkov]

The PMIC is not a part of the SoC, so move PMIC to a separate file and
include it from the board files.

Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8058.dtsi            | 160 ++++++++++++++++++
 .../dts/qcom/qcom-apq8060-dragonboard.dts     |   1 +
 arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts  |   1 +
 arch/arm/boot/dts/qcom/qcom-msm8660.dtsi      | 149 +---------------
 4 files changed, 163 insertions(+), 148 deletions(-)
 create mode 100644 arch/arm/boot/dts/qcom/pm8058.dtsi

diff --git a/arch/arm/boot/dts/qcom/pm8058.dtsi b/arch/arm/boot/dts/qcom/pm8058.dtsi
new file mode 100644
index 000000000000..ad581c3bcbd2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8058.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: GPL-2.0
+
+&ssbi {
+	pm8058: pmic {
+		compatible = "qcom,pm8058";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8058_gpio: gpio@150 {
+			compatible = "qcom,pm8058-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8058_gpio 0 0 44>;
+			#gpio-cells = <2>;
+		};
+
+		pm8058_mpps: mpps@50 {
+			compatible = "qcom,pm8058-mpp",
+				     "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8058_mpps 0 0 12>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pwrkey@1c {
+			compatible = "qcom,pm8058-pwrkey";
+			reg = <0x1c>;
+			interrupt-parent = <&pm8058>;
+			interrupts = <50 1>, <51 1>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8058_keypad: keypad@148 {
+			compatible = "qcom,pm8058-keypad";
+			reg = <0x148>;
+			interrupt-parent = <&pm8058>;
+			interrupts = <74 1>, <75 1>;
+			debounce = <15>;
+			scan-delay = <32>;
+			row-hold = <91500>;
+		};
+
+		pm8058_xoadc: xoadc@197 {
+			compatible = "qcom,pm8058-adc";
+			reg = <0x197>;
+			interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			#io-channel-cells = <2>;
+
+			vcoin: adc-channel@0 {
+				reg = <0x00 0x00>;
+			};
+
+			vbat: adc-channel@1 {
+				reg = <0x00 0x01>;
+			};
+
+			dcin: adc-channel@2 {
+				reg = <0x00 0x02>;
+			};
+
+			ichg: adc-channel@3 {
+				reg = <0x00 0x03>;
+			};
+
+			vph_pwr: adc-channel@4 {
+				reg = <0x00 0x04>;
+			};
+
+			usb_vbus: adc-channel@a {
+				reg = <0x00 0x0a>;
+			};
+
+			die_temp: adc-channel@b {
+				reg = <0x00 0x0b>;
+			};
+
+			ref_625mv: adc-channel@c {
+				reg = <0x00 0x0c>;
+			};
+
+			ref_1250mv: adc-channel@d {
+				reg = <0x00 0x0d>;
+			};
+
+			ref_325mv: adc-channel@e {
+				reg = <0x00 0x0e>;
+			};
+
+			ref_muxoff: adc-channel@f {
+				reg = <0x00 0x0f>;
+			};
+		};
+
+		rtc@1e8 {
+			compatible = "qcom,pm8058-rtc";
+			reg = <0x1e8>;
+			interrupt-parent = <&pm8058>;
+			interrupts = <39 1>;
+			allow-set-time;
+		};
+
+		vibrator@4a {
+			compatible = "qcom,pm8058-vib";
+			reg = <0x4a>;
+		};
+
+		pm8058_led48: led@48 {
+			compatible = "qcom,pm8058-keypad-led";
+			reg = <0x48>;
+			status = "disabled";
+		};
+
+		pm8058_led131: led@131 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x131>;
+			status = "disabled";
+		};
+
+		pm8058_led132: led@132 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x132>;
+			status = "disabled";
+		};
+
+		pm8058_led133: led@133 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x133>;
+			status = "disabled";
+		};
+	};
+};
+
+/ {
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&pm8058_xoadc 0x00 0x01>, /* Battery */
+			      <&pm8058_xoadc 0x00 0x02>, /* DC in (charger) */
+			      <&pm8058_xoadc 0x00 0x04>, /* VPH the main system voltage */
+			      <&pm8058_xoadc 0x00 0x0b>, /* Die temperature */
+			      <&pm8058_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			      <&pm8058_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			      <&pm8058_xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
index e4261d729d35..10b8f529c337 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
@@ -5,6 +5,7 @@
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
 #include "qcom-msm8660.dtsi"
+#include "pm8058.dtsi"
 
 / {
 	model = "Qualcomm APQ8060 Dragonboard";
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
index a5441aecd637..be2fbc1e0950 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
@@ -2,6 +2,7 @@
 #include <dt-bindings/input/input.h>
 
 #include "qcom-msm8660.dtsi"
+#include "pm8058.dtsi"
 
 / {
 	model = "Qualcomm MSM8660 SURF";
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
index 84b0366792d4..eef4712bbcc4 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
@@ -73,22 +73,6 @@ sleep-clk {
 		};
 	};
 
-	/*
-	 * These channels from the ADC are simply hardware monitors.
-	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
-	 * ADC.
-	 */
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&pm8058_xoadc 0x00 0x01>, /* Battery */
-			      <&pm8058_xoadc 0x00 0x02>, /* DC in (charger) */
-			      <&pm8058_xoadc 0x00 0x04>, /* VPH the main system voltage */
-			      <&pm8058_xoadc 0x00 0x0b>, /* Die temperature */
-			      <&pm8058_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
-			      <&pm8058_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
-			      <&pm8058_xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
-	};
-
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -334,141 +318,10 @@ ebi2: external-bus@1a100000 {
 			status = "disabled";
 		};
 
-		ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8058: pmic {
-				compatible = "qcom,pm8058";
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8058_gpio: gpio@150 {
-					compatible = "qcom,pm8058-gpio",
-						     "qcom,ssbi-gpio";
-					reg = <0x150>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pm8058_gpio 0 0 44>;
-					#gpio-cells = <2>;
-
-				};
-
-				pm8058_mpps: mpps@50 {
-					compatible = "qcom,pm8058-mpp",
-						     "qcom,ssbi-mpp";
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pm8058_mpps 0 0 12>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-				};
-
-				pwrkey@1c {
-					compatible = "qcom,pm8058-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pm8058>;
-					interrupts = <50 1>, <51 1>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				pm8058_keypad: keypad@148 {
-					compatible = "qcom,pm8058-keypad";
-					reg = <0x148>;
-					interrupt-parent = <&pm8058>;
-					interrupts = <74 1>, <75 1>;
-					debounce = <15>;
-					scan-delay = <32>;
-					row-hold = <91500>;
-				};
-
-				pm8058_xoadc: xoadc@197 {
-					compatible = "qcom,pm8058-adc";
-					reg = <0x197>;
-					interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-					#io-channel-cells = <2>;
-
-					vcoin: adc-channel@0 {
-						reg = <0x00 0x00>;
-					};
-					vbat: adc-channel@1 {
-						reg = <0x00 0x01>;
-					};
-					dcin: adc-channel@2 {
-						reg = <0x00 0x02>;
-					};
-					ichg: adc-channel@3 {
-						reg = <0x00 0x03>;
-					};
-					vph_pwr: adc-channel@4 {
-						reg = <0x00 0x04>;
-					};
-					usb_vbus: adc-channel@a {
-						reg = <0x00 0x0a>;
-					};
-					die_temp: adc-channel@b {
-						reg = <0x00 0x0b>;
-					};
-					ref_625mv: adc-channel@c {
-						reg = <0x00 0x0c>;
-					};
-					ref_1250mv: adc-channel@d {
-						reg = <0x00 0x0d>;
-					};
-					ref_325mv: adc-channel@e {
-						reg = <0x00 0x0e>;
-					};
-					ref_muxoff: adc-channel@f {
-						reg = <0x00 0x0f>;
-					};
-				};
-
-				rtc@1e8 {
-					compatible = "qcom,pm8058-rtc";
-					reg = <0x1e8>;
-					interrupt-parent = <&pm8058>;
-					interrupts = <39 1>;
-					allow-set-time;
-				};
-
-				vibrator@4a {
-					compatible = "qcom,pm8058-vib";
-					reg = <0x4a>;
-				};
-
-				pm8058_led48: led@48 {
-					compatible = "qcom,pm8058-keypad-led";
-					reg = <0x48>;
-					status = "disabled";
-				};
-
-				pm8058_led131: led@131 {
-					compatible = "qcom,pm8058-led";
-					reg = <0x131>;
-					status = "disabled";
-				};
-
-				pm8058_led132: led@132 {
-					compatible = "qcom,pm8058-led";
-					reg = <0x132>;
-					status = "disabled";
-				};
-
-				pm8058_led133: led@133 {
-					compatible = "qcom,pm8058-led";
-					reg = <0x133>;
-					status = "disabled";
-				};
-
-			};
 		};
 
 		l2cc: clock-controller@2082000 {
-- 
2.39.2

[PATCH v4 22/38] ARM: dts: qcom: pm8058: reorder nodes

[Dmitry Baryshkov]

Move pm8058 device nodes to follow the alphanumberic sorting order.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8058.dtsi | 90 +++++++++++++++---------------
 1 file changed, 45 insertions(+), 45 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/pm8058.dtsi b/arch/arm/boot/dts/qcom/pm8058.dtsi
index ad581c3bcbd2..913a511719fa 100644
--- a/arch/arm/boot/dts/qcom/pm8058.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8058.dtsi
@@ -8,15 +8,24 @@ pm8058: pmic {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pm8058_gpio: gpio@150 {
-			compatible = "qcom,pm8058-gpio",
-				     "qcom,ssbi-gpio";
-			reg = <0x150>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			gpio-controller;
-			gpio-ranges = <&pm8058_gpio 0 0 44>;
-			#gpio-cells = <2>;
+		pwrkey@1c {
+			compatible = "qcom,pm8058-pwrkey";
+			reg = <0x1c>;
+			interrupt-parent = <&pm8058>;
+			interrupts = <50 1>, <51 1>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8058_led48: led@48 {
+			compatible = "qcom,pm8058-keypad-led";
+			reg = <0x48>;
+			status = "disabled";
+		};
+
+		vibrator@4a {
+			compatible = "qcom,pm8058-vib";
+			reg = <0x4a>;
 		};
 
 		pm8058_mpps: mpps@50 {
@@ -30,13 +39,22 @@ pm8058_mpps: mpps@50 {
 			#interrupt-cells = <2>;
 		};
 
-		pwrkey@1c {
-			compatible = "qcom,pm8058-pwrkey";
-			reg = <0x1c>;
-			interrupt-parent = <&pm8058>;
-			interrupts = <50 1>, <51 1>;
-			debounce = <15625>;
-			pull-up;
+		pm8058_led131: led@131 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x131>;
+			status = "disabled";
+		};
+
+		pm8058_led132: led@132 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x132>;
+			status = "disabled";
+		};
+
+		pm8058_led133: led@133 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x133>;
+			status = "disabled";
 		};
 
 		pm8058_keypad: keypad@148 {
@@ -49,6 +67,17 @@ pm8058_keypad: keypad@148 {
 			row-hold = <91500>;
 		};
 
+		pm8058_gpio: gpio@150 {
+			compatible = "qcom,pm8058-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8058_gpio 0 0 44>;
+			#gpio-cells = <2>;
+		};
+
 		pm8058_xoadc: xoadc@197 {
 			compatible = "qcom,pm8058-adc";
 			reg = <0x197>;
@@ -109,35 +138,6 @@ rtc@1e8 {
 			interrupts = <39 1>;
 			allow-set-time;
 		};
-
-		vibrator@4a {
-			compatible = "qcom,pm8058-vib";
-			reg = <0x4a>;
-		};
-
-		pm8058_led48: led@48 {
-			compatible = "qcom,pm8058-keypad-led";
-			reg = <0x48>;
-			status = "disabled";
-		};
-
-		pm8058_led131: led@131 {
-			compatible = "qcom,pm8058-led";
-			reg = <0x131>;
-			status = "disabled";
-		};
-
-		pm8058_led132: led@132 {
-			compatible = "qcom,pm8058-led";
-			reg = <0x132>;
-			status = "disabled";
-		};
-
-		pm8058_led133: led@133 {
-			compatible = "qcom,pm8058-led";
-			reg = <0x133>;
-			status = "disabled";
-		};
 	};
 };
 
-- 
2.39.2

[PATCH v4 23/38] ARM: dts: qcom: pm8921: reorder nodes

[Dmitry Baryshkov]

Move pm8921 device nodes to follow the alphanumberic sorting order.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8921.dtsi | 48 +++++++++++++++---------------
 1 file changed, 24 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/pm8921.dtsi b/arch/arm/boot/dts/qcom/pm8921.dtsi
index ad41d99ab265..4697ca33666f 100644
--- a/arch/arm/boot/dts/qcom/pm8921.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8921.dtsi
@@ -8,17 +8,14 @@ pm8921: pmic {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pm8921_gpio: gpio@150 {
-
-			compatible = "qcom,pm8921-gpio",
-				     "qcom,ssbi-gpio";
-			reg = <0x150>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			gpio-controller;
-			gpio-ranges = <&pm8921_gpio 0 0 44>;
-			#gpio-cells = <2>;
-
+		pwrkey@1c {
+			compatible = "qcom,pm8921-pwrkey";
+			reg = <0x1c>;
+			interrupt-parent = <&pm8921>;
+			interrupts = <50 IRQ_TYPE_EDGE_RISING>,
+				     <51 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15625>;
+			pull-up;
 		};
 
 		pm8921_mpps: mpps@50 {
@@ -32,14 +29,12 @@ pm8921_mpps: mpps@50 {
 			#interrupt-cells = <2>;
 		};
 
-		pwrkey@1c {
-			compatible = "qcom,pm8921-pwrkey";
-			reg = <0x1c>;
+		rtc@11d {
+			compatible = "qcom,pm8921-rtc";
 			interrupt-parent = <&pm8921>;
-			interrupts = <50 IRQ_TYPE_EDGE_RISING>,
-				     <51 IRQ_TYPE_EDGE_RISING>;
-			debounce = <15625>;
-			pull-up;
+			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
+			reg = <0x11d>;
+			allow-set-time;
 		};
 
 		pm8921_keypad: keypad@148 {
@@ -53,12 +48,17 @@ pm8921_keypad: keypad@148 {
 			row-hold = <91500>;
 		};
 
-		rtc@11d {
-			compatible = "qcom,pm8921-rtc";
-			interrupt-parent = <&pm8921>;
-			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
-			reg = <0x11d>;
-			allow-set-time;
+		pm8921_gpio: gpio@150 {
+
+			compatible = "qcom,pm8921-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8921_gpio 0 0 44>;
+			#gpio-cells = <2>;
+
 		};
 
 		pm8921_xoadc: xoadc@197 {
-- 
2.39.2

[PATCH v4 24/38] ARM: dts: qcom: pm8018: move reg property

[Dmitry Baryshkov]

Move reg property to come after compatible.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8018.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/pm8018.dtsi b/arch/arm/boot/dts/qcom/pm8018.dtsi
index c602544900b2..85ab36b6d006 100644
--- a/arch/arm/boot/dts/qcom/pm8018.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8018.dtsi
@@ -27,9 +27,9 @@ pwrkey@1c {
 
 		pm8018_mpps: mpps@50 {
 			compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
+			reg = <0x50>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
-			reg = <0x50>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pm8018_mpps 0 0 6>;
@@ -37,9 +37,9 @@ pm8018_mpps: mpps@50 {
 
 		rtc@11d {
 			compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
+			reg = <0x11d>;
 			interrupt-parent = <&pm8018>;
 			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
-			reg = <0x11d>;
 			allow-set-time;
 		};
 
-- 
2.39.2

[PATCH v4 25/38] ARM: dts: qcom: pm8921: move reg property

[Dmitry Baryshkov]

Move reg property to come after compatible.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8921.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/qcom/pm8921.dtsi b/arch/arm/boot/dts/qcom/pm8921.dtsi
index 4697ca33666f..fa00b57e28b9 100644
--- a/arch/arm/boot/dts/qcom/pm8921.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8921.dtsi
@@ -31,9 +31,9 @@ pm8921_mpps: mpps@50 {
 
 		rtc@11d {
 			compatible = "qcom,pm8921-rtc";
+			reg = <0x11d>;
 			interrupt-parent = <&pm8921>;
 			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
-			reg = <0x11d>;
 			allow-set-time;
 		};
 
-- 
2.39.2

[PATCH v4 26/38] ARM: dts: qcom: pm8058: use defined IRQ flags

[Dmitry Baryshkov]

Use symbolic names for IRQ flags instead of using the numeric values.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8058.dtsi | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/pm8058.dtsi b/arch/arm/boot/dts/qcom/pm8058.dtsi
index 913a511719fa..3683d7b60918 100644
--- a/arch/arm/boot/dts/qcom/pm8058.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8058.dtsi
@@ -12,7 +12,8 @@ pwrkey@1c {
 			compatible = "qcom,pm8058-pwrkey";
 			reg = <0x1c>;
 			interrupt-parent = <&pm8058>;
-			interrupts = <50 1>, <51 1>;
+			interrupts = <50 IRQ_TYPE_EDGE_RISING>,
+				     <51 IRQ_TYPE_EDGE_RISING>;
 			debounce = <15625>;
 			pull-up;
 		};
@@ -61,7 +62,8 @@ pm8058_keypad: keypad@148 {
 			compatible = "qcom,pm8058-keypad";
 			reg = <0x148>;
 			interrupt-parent = <&pm8058>;
-			interrupts = <74 1>, <75 1>;
+			interrupts = <74 IRQ_TYPE_EDGE_RISING>,
+				     <75 IRQ_TYPE_EDGE_RISING>;
 			debounce = <15>;
 			scan-delay = <32>;
 			row-hold = <91500>;
@@ -135,7 +137,7 @@ rtc@1e8 {
 			compatible = "qcom,pm8058-rtc";
 			reg = <0x1e8>;
 			interrupt-parent = <&pm8058>;
-			interrupts = <39 1>;
+			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
 			allow-set-time;
 		};
 	};
-- 
2.39.2

[PATCH v4 27/38] ARM: dts: qcom: pm8921: switch to interrupts-extended

[Dmitry Baryshkov]

Merge interrups and interrupt-parent properties into a single
interrupts-extended property.

Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad DYbcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8921.dtsi | 13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/pm8921.dtsi b/arch/arm/boot/dts/qcom/pm8921.dtsi
index fa00b57e28b9..360a179670c5 100644
--- a/arch/arm/boot/dts/qcom/pm8921.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8921.dtsi
@@ -11,9 +11,8 @@ pm8921: pmic {
 		pwrkey@1c {
 			compatible = "qcom,pm8921-pwrkey";
 			reg = <0x1c>;
-			interrupt-parent = <&pm8921>;
-			interrupts = <50 IRQ_TYPE_EDGE_RISING>,
-				     <51 IRQ_TYPE_EDGE_RISING>;
+			interrupts-extended = <&pm8921 50 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8921 51 IRQ_TYPE_EDGE_RISING>;
 			debounce = <15625>;
 			pull-up;
 		};
@@ -32,17 +31,15 @@ pm8921_mpps: mpps@50 {
 		rtc@11d {
 			compatible = "qcom,pm8921-rtc";
 			reg = <0x11d>;
-			interrupt-parent = <&pm8921>;
-			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
+			interrupts-extended = <&pm8921 39 IRQ_TYPE_EDGE_RISING>;
 			allow-set-time;
 		};
 
 		pm8921_keypad: keypad@148 {
 			compatible = "qcom,pm8921-keypad";
 			reg = <0x148>;
-			interrupt-parent = <&pm8921>;
-			interrupts = <74 IRQ_TYPE_EDGE_RISING>,
-				     <75 IRQ_TYPE_EDGE_RISING>;
+			interrupts-extended = <&pm8921 74 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8921 75 IRQ_TYPE_EDGE_RISING>;
 			debounce = <15>;
 			scan-delay = <32>;
 			row-hold = <91500>;
-- 
2.39.2

[PATCH v4 28/38] ARM: dts: qcom: pm8018: switch to interrupts-extended

[Dmitry Baryshkov]

Merge interrups and interrupt-parent properties into a single
interrupts-extended property.

Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8018.dtsi | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/pm8018.dtsi b/arch/arm/boot/dts/qcom/pm8018.dtsi
index 85ab36b6d006..22f3c7bac522 100644
--- a/arch/arm/boot/dts/qcom/pm8018.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8018.dtsi
@@ -18,9 +18,8 @@ pwrkey@1c {
 			compatible = "qcom,pm8018-pwrkey",
 				     "qcom,pm8921-pwrkey";
 			reg = <0x1c>;
-			interrupt-parent = <&pm8018>;
-			interrupts = <50 IRQ_TYPE_EDGE_RISING>,
-				     <51 IRQ_TYPE_EDGE_RISING>;
+			interrupts-extended = <&pm8018 50 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8018 51 IRQ_TYPE_EDGE_RISING>;
 			debounce = <15625>;
 			pull-up;
 		};
@@ -38,8 +37,7 @@ pm8018_mpps: mpps@50 {
 		rtc@11d {
 			compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
 			reg = <0x11d>;
-			interrupt-parent = <&pm8018>;
-			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
+			interrupts-extended = <&pm8018 39 IRQ_TYPE_EDGE_RISING>;
 			allow-set-time;
 		};
 
-- 
2.39.2

[PATCH v4 29/38] ARM: dts: qcom: pm8058: switch to interrupts-extended

[Dmitry Baryshkov]

Merge interrups and interrupt-parent properties into a single
interrupts-extended property.

Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8058.dtsi | 13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/pm8058.dtsi b/arch/arm/boot/dts/qcom/pm8058.dtsi
index 3683d7b60918..984b79777984 100644
--- a/arch/arm/boot/dts/qcom/pm8058.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8058.dtsi
@@ -11,9 +11,8 @@ pm8058: pmic {
 		pwrkey@1c {
 			compatible = "qcom,pm8058-pwrkey";
 			reg = <0x1c>;
-			interrupt-parent = <&pm8058>;
-			interrupts = <50 IRQ_TYPE_EDGE_RISING>,
-				     <51 IRQ_TYPE_EDGE_RISING>;
+			interrupts-extended = <&pm8058 50 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8058 51 IRQ_TYPE_EDGE_RISING>;
 			debounce = <15625>;
 			pull-up;
 		};
@@ -61,9 +60,8 @@ pm8058_led133: led@133 {
 		pm8058_keypad: keypad@148 {
 			compatible = "qcom,pm8058-keypad";
 			reg = <0x148>;
-			interrupt-parent = <&pm8058>;
-			interrupts = <74 IRQ_TYPE_EDGE_RISING>,
-				     <75 IRQ_TYPE_EDGE_RISING>;
+			interrupts-extended = <&pm8058 74 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8058 75 IRQ_TYPE_EDGE_RISING>;
 			debounce = <15>;
 			scan-delay = <32>;
 			row-hold = <91500>;
@@ -136,8 +134,7 @@ ref_muxoff: adc-channel@f {
 		rtc@1e8 {
 			compatible = "qcom,pm8058-rtc";
 			reg = <0x1e8>;
-			interrupt-parent = <&pm8058>;
-			interrupts = <39 IRQ_TYPE_EDGE_RISING>;
+			interrupts-extended = <&pm8058 39 IRQ_TYPE_EDGE_RISING>;
 			allow-set-time;
 		};
 	};
-- 
2.39.2

[PATCH v4 30/38] ARM: dts: qcom: apq8064: move RPM regulators to board files

[Dmitry Baryshkov]

The set of regulators available over the RPM requests is not a property
of the SoC. Move them to board files.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../dts/qcom/qcom-apq8064-asus-nexus7-flo.dts | 42 ++++----
 .../boot/dts/qcom/qcom-apq8064-cm-qs600.dts   | 22 ++---
 .../boot/dts/qcom/qcom-apq8064-ifc6410.dts    | 29 +++---
 .../qcom-apq8064-sony-xperia-lagan-yuga.dts   | 98 +++++++++++--------
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi      | 63 ------------
 5 files changed, 108 insertions(+), 146 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
index d709d6e840ec..329c2546aa0a 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
@@ -199,11 +199,12 @@ &pm8921 {
 
 &rpm {
 	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
 		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
 		vin_lvs1_3_6-supply = <&pm8921_s4>;
 		vin_lvs4_5_7-supply = <&pm8921_s4>;
 
-
 		vdd_l24-supply = <&pm8921_s1>;
 		vdd_l25-supply = <&pm8921_s1>;
 		vin_lvs2-supply = <&pm8921_s1>;
@@ -215,7 +216,7 @@ regulators {
 		vdd_ncp-supply = <&pm8921_l6>;
 
 		/* Buck SMPS */
-		s1 {
+		pm8921_s1: s1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
@@ -224,7 +225,7 @@ s1 {
 		};
 
 		/* msm otg HSUSB_VDDCX */
-		s3 {
+		pm8921_s3: s3 {
 			regulator-min-microvolt = <500000>;
 			regulator-max-microvolt = <1150000>;
 			qcom,switch-mode-frequency = <4800000>;
@@ -237,55 +238,58 @@ s3 {
 		 * tabla2x-slim-CDC_VDD_CP
 		 * tabla2x-slim-VDDIO_CDC
 		 */
-		s4 {
+		pm8921_s4: s4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <3200000>;
 			regulator-always-on;
 		};
 
-		s7 {
+		pm8921_s7: s7 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
 		/* mipi_dsi.1-dsi1_pll_vdda */
-		l2 {
+		pm8921_l2: l2 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			regulator-always-on;
 		};
 
 		/* msm_otg-HSUSB_3p3 */
-		l3 {
+		pm8921_l3: l3 {
 			regulator-min-microvolt = <3075000>;
 			regulator-max-microvolt = <3075000>;
 			bias-pull-down;
 		};
 
 		/* msm_otg-HSUSB_1p8 */
-		l4 {
+		pm8921_l4: l4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
 		/* msm_sdcc.1-sdc_vdd */
-		l5 {
+		pm8921_l5: l5 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 			regulator-always-on;
 			bias-pull-down;
 		};
 
-		l6 {
+		pm8921_l6: l6 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 		};
 
+		pm8921_l8: l8 {
+		};
+
 		/* mipi_dsi.1-dsi1_avdd */
-		l11 {
+		pm8921_l11: l11 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
@@ -293,14 +297,14 @@ l11 {
 		};
 
 		/* pwm_power for backlight */
-		l17 {
+		pm8921_l17: l17 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
 			regulator-always-on;
 		};
 
 		/* camera, qdsp6 */
-		l23 {
+		pm8921_l23: l23 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
@@ -310,32 +314,32 @@ l23 {
 		 * tabla2x-slim-CDC_VDDA_A_1P2V
 		 * tabla2x-slim-VDDD_CDC_D
 		 */
-		l25 {
+		pm8921_l25: l25 {
 			regulator-min-microvolt = <1250000>;
 			regulator-max-microvolt = <1250000>;
 			bias-pull-down;
 		};
 
-		lvs1 {
+		pm8921_lvs1: lvs1 {
 			bias-pull-down;
 		};
 
-		lvs4 {
+		pm8921_lvs4: lvs4 {
 			bias-pull-down;
 		};
 
-		lvs5 {
+		pm8921_lvs5: lvs5 {
 			bias-pull-down;
 		};
 
-		lvs6 {
+		pm8921_lvs6: lvs6 {
 			bias-pull-down;
 		};
 		/*
 		 * mipi_dsi.1-dsi1_vddio
 		 * pil_riva-pll_vdd
 		 */
-		lvs7 {
+		pm8921_lvs7: lvs7 {
 			bias-pull-down;
 		};
 	};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
index d4db84e9fcf3..671d58cc2741 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
@@ -93,6 +93,8 @@ pinconf {
 
 &rpm {
 	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
 		vin_lvs1_3_6-supply = <&pm8921_s4>;
 		vin_lvs2-supply = <&pm8921_s1>;
 		vin_lvs4_5_7-supply = <&pm8921_s4>;
@@ -104,9 +106,8 @@ regulators {
 		vdd_l27-supply = <&pm8921_s7>;
 		vdd_l28-supply = <&pm8921_s7>;
 
-
 		/* Buck SMPS */
-		s1 {
+		pm8921_s1: s1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
@@ -114,52 +115,51 @@ s1 {
 			bias-pull-down;
 		};
 
-		s3 {
+		pm8921_s3: s3 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1400000>;
 			qcom,switch-mode-frequency = <4800000>;
 		};
 
-		s4 {
+		pm8921_s4: s4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		s7 {
+		pm8921_s7: s7 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		l3 {
+		pm8921_l3: l3 {
 			regulator-min-microvolt = <3050000>;
 			regulator-max-microvolt = <3300000>;
 			bias-pull-down;
 		};
 
-		l4 {
+		pm8921_l4: l4 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l5 {
+		pm8921_l5: l5 {
 			regulator-min-microvolt = <2750000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
 		};
 
-		l23 {
+		pm8921_l23: l23 {
 			regulator-min-microvolt = <1700000>;
 			regulator-max-microvolt = <1900000>;
 			bias-pull-down;
 		};
 
-		lvs6 {
+		pm8921_lvs6: lvs6 {
 			bias-pull-down;
 		};
-
 	};
 };
 
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
index 5fd84319254e..3078afda37c6 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
@@ -204,6 +204,8 @@ pinconf {
 
 &rpm {
 	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
 		vin_lvs1_3_6-supply = <&pm8921_s4>;
 		vin_lvs2-supply = <&pm8921_s1>;
 		vin_lvs4_5_7-supply = <&pm8921_s4>;
@@ -215,9 +217,8 @@ regulators {
 		vdd_l27-supply = <&pm8921_s7>;
 		vdd_l28-supply = <&pm8921_s7>;
 
-
 		/* Buck SMPS */
-		s1 {
+		pm8921_s1: s1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
@@ -225,59 +226,63 @@ s1 {
 			bias-pull-down;
 		};
 
-		s3 {
+		pm8921_s3: s3 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1400000>;
 			qcom,switch-mode-frequency = <4800000>;
 		};
 
-		s4 {
+		pm8921_s4: s4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		s7 {
+		pm8921_s7: s7 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		l3 {
+		pm8921_l3: l3 {
 			regulator-min-microvolt = <3050000>;
 			regulator-max-microvolt = <3300000>;
 			bias-pull-down;
 		};
 
-		l4 {
+		pm8921_l4: l4 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l5 {
+		pm8921_l5: l5 {
 			regulator-min-microvolt = <2750000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
 		};
 
-		l6 {
+		pm8921_l6: l6 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l23 {
+		pm8921_l23: l23 {
 			regulator-min-microvolt = <1700000>;
 			regulator-max-microvolt = <1900000>;
 			bias-pull-down;
 		};
 
-		lvs1 {
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
 			bias-pull-down;
 		};
 
-		lvs6 {
+		pm8921_hdmi_switch: hdmi-switch {
 			bias-pull-down;
 		};
 	};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
index ba18a02b1c57..2412aa3e3e8d 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
@@ -93,11 +93,25 @@ gpio_keys_pin_a: gpio-keys-active-state {
 &riva {
 	pinctrl-names = "default";
 	pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
+
+	vddcx-supply = <&pm8921_s3>;
+	vddmx-supply = <&pm8921_l24>;
+	vddpx-supply = <&pm8921_s4>;
+
 	status = "okay";
+
+	iris {
+		vddxo-supply = <&pm8921_l4>;
+		vddrfa-supply = <&pm8921_s2>;
+		vddpa-supply = <&pm8921_l10>;
+		vdddig-supply = <&pm8921_lvs2>;
+	};
 };
 
 &rpm {
 	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
 		vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
 		vin_lvs_1_3_6-supply = <&pm8921_s4>;
 		vin_lvs_4_5_7-supply = <&pm8921_s4>;
@@ -109,7 +123,7 @@ regulators {
 		vin_l28-supply = <&pm8921_s7>;
 
 		/* Buck SMPS */
-		s1 {
+		pm8921_s1: s1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
@@ -117,21 +131,21 @@ s1 {
 			bias-pull-down;
 		};
 
-		s2 {
+		pm8921_s2: s2 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <1600000>;
 			bias-pull-down;
 		};
 
-		s3 {
+		pm8921_s3: s3 {
 			regulator-min-microvolt = <500000>;
 			regulator-max-microvolt = <1150000>;
 			qcom,switch-mode-frequency = <4800000>;
 			bias-pull-down;
 		};
 
-		s4 {
+		pm8921_s4: s4 {
 			regulator-always-on;
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
@@ -140,205 +154,207 @@ s4 {
 			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
 		};
 
-		s7 {
+		pm8921_s7: s7 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		s8 {
+		pm8921_s8: s8 {
 			regulator-min-microvolt = <2200000>;
 			regulator-max-microvolt = <2200000>;
 			qcom,switch-mode-frequency = <1600000>;
 		};
 
 		/* PMOS LDO */
-		l1 {
+		pm8921_l1: l1 {
 			regulator-always-on;
 			regulator-min-microvolt = <1100000>;
 			regulator-max-microvolt = <1100000>;
 			bias-pull-down;
 		};
 
-		l2 {
+		pm8921_l2: l2 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
 
-		l3 {
+		pm8921_l3: l3 {
 			regulator-min-microvolt = <3075000>;
 			regulator-max-microvolt = <3075000>;
 			bias-pull-down;
 		};
 
-		l4 {
+		pm8921_l4: l4 {
 			regulator-always-on;
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l5 {
+		pm8921_l5: l5 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l6 {
+		pm8921_l6: l6 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l7 {
+		pm8921_l7: l7 {
 			regulator-min-microvolt = <1850000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l8 {
+		pm8921_l8: l8 {
 			regulator-min-microvolt = <2800000>;
 			regulator-max-microvolt = <2800000>;
 			bias-pull-down;
 		};
 
-		l9 {
+		pm8921_l9: l9 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
 		};
 
-		l10 {
+		pm8921_l10: l10 {
 			regulator-min-microvolt = <2900000>;
 			regulator-max-microvolt = <2900000>;
 			bias-pull-down;
 		};
 
-		l11 {
+		pm8921_l11: l11 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
 			bias-pull-down;
 		};
 
-		l12 {
+		pm8921_l12: l12 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
 
-		l14 {
+		pm8921_l14: l14 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l15 {
+		pm8921_l15: l15 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <2950000>;
 			bias-pull-down;
 		};
 
-		l16 {
+		pm8921_l16: l16 {
 			regulator-min-microvolt = <2800000>;
 			regulator-max-microvolt = <2800000>;
 			bias-pull-down;
 		};
 
-		l17 {
+		pm8921_l17: l17 {
 			regulator-min-microvolt = <2000000>;
 			regulator-max-microvolt = <2000000>;
 			bias-pull-down;
 		};
 
-		l18 {
+		pm8921_l18: l18 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
 
-		l21 {
+		pm8921_l21: l21 {
 			regulator-min-microvolt = <1050000>;
 			regulator-max-microvolt = <1050000>;
 			bias-pull-down;
 		};
 
-		l22 {
+		pm8921_l22: l22 {
 			regulator-min-microvolt = <2600000>;
 			regulator-max-microvolt = <2600000>;
 			bias-pull-down;
 		};
 
-		l23 {
+		pm8921_l23: l23 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
 
-		l24 {
+		pm8921_l24: l24 {
 			regulator-min-microvolt = <750000>;
 			regulator-max-microvolt = <1150000>;
 			bias-pull-down;
 		};
 
-		l25 {
+		pm8921_l25: l25 {
 			regulator-always-on;
 			regulator-min-microvolt = <1250000>;
 			regulator-max-microvolt = <1250000>;
 			bias-pull-down;
 		};
 
-		l27 {
+		pm8921_l27: l27 {
 			regulator-min-microvolt = <1100000>;
 			regulator-max-microvolt = <1100000>;
 		};
 
-		l28 {
+		pm8921_l28: l28 {
 			regulator-min-microvolt = <1050000>;
 			regulator-max-microvolt = <1050000>;
 			bias-pull-down;
 		};
 
-		l29 {
+		pm8921_l29: l29 {
 			regulator-min-microvolt = <2000000>;
 			regulator-max-microvolt = <2000000>;
 			bias-pull-down;
 		};
 
 		/* Low Voltage Switch */
-		lvs1 {
+		pm8921_lvs1: lvs1 {
 			bias-pull-down;
 		};
 
-		lvs2 {
+		pm8921_lvs2: lvs2 {
 			bias-pull-down;
 		};
 
-		lvs3 {
+		pm8921_lvs3: lvs3 {
 			bias-pull-down;
 		};
 
-		lvs4 {
+		pm8921_lvs4: lvs4 {
 			bias-pull-down;
 		};
 
-		lvs5 {
+		pm8921_lvs5: lvs5 {
 			bias-pull-down;
 		};
 
-		lvs6 {
+		pm8921_lvs6: lvs6 {
 			bias-pull-down;
 		};
 
-		lvs7 {
+		pm8921_lvs7: lvs7 {
 			bias-pull-down;
 		};
 
-		usb-switch {};
+		pm8921_usb_switch: usb-switch {};
 
-		hdmi-switch {};
+		pm8921_hdmi_switch: hdmi-switch {
+			bias-pull-down;
+		};
 
-		ncp {
+		pm8921_ncp: ncp {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <1600000>;
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index 5704d0598b96..5b7d2c6f0ce9 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -757,60 +757,6 @@ rpmcc: clock-controller {
 				clocks = <&pxo_board>, <&cxo_board>;
 				clock-names = "pxo", "cxo";
 			};
-
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-
-				pm8921_s1: s1 {};
-				pm8921_s2: s2 {};
-				pm8921_s3: s3 {};
-				pm8921_s4: s4 {};
-				pm8921_s7: s7 {};
-				pm8921_s8: s8 {};
-
-				pm8921_l1: l1 {};
-				pm8921_l2: l2 {};
-				pm8921_l3: l3 {};
-				pm8921_l4: l4 {};
-				pm8921_l5: l5 {};
-				pm8921_l6: l6 {};
-				pm8921_l7: l7 {};
-				pm8921_l8: l8 {};
-				pm8921_l9: l9 {};
-				pm8921_l10: l10 {};
-				pm8921_l11: l11 {};
-				pm8921_l12: l12 {};
-				pm8921_l14: l14 {};
-				pm8921_l15: l15 {};
-				pm8921_l16: l16 {};
-				pm8921_l17: l17 {};
-				pm8921_l18: l18 {};
-				pm8921_l21: l21 {};
-				pm8921_l22: l22 {};
-				pm8921_l23: l23 {};
-				pm8921_l24: l24 {};
-				pm8921_l25: l25 {};
-				pm8921_l26: l26 {};
-				pm8921_l27: l27 {};
-				pm8921_l28: l28 {};
-				pm8921_l29: l29 {};
-
-				pm8921_lvs1: lvs1 {};
-				pm8921_lvs2: lvs2 {};
-				pm8921_lvs3: lvs3 {};
-				pm8921_lvs4: lvs4 {};
-				pm8921_lvs5: lvs5 {};
-				pm8921_lvs6: lvs6 {};
-				pm8921_lvs7: lvs7 {};
-
-				pm8921_usb_switch: usb-switch {};
-
-				pm8921_hdmi_switch: hdmi-switch {
-					bias-pull-down;
-				};
-
-				pm8921_ncp: ncp {};
-			};
 		};
 
 		usb1: usb@12500000 {
@@ -1490,10 +1436,6 @@ riva: riva-pil@3200800 {
 
 			memory-region = <&wcnss_mem>;
 
-			vddcx-supply = <&pm8921_s3>;
-			vddmx-supply = <&pm8921_l24>;
-			vddpx-supply = <&pm8921_s4>;
-
 			status = "disabled";
 
 			iris {
@@ -1501,11 +1443,6 @@ iris {
 
 				clocks = <&cxo_board>;
 				clock-names = "xo";
-
-				vddxo-supply = <&pm8921_l4>;
-				vddrfa-supply = <&pm8921_s2>;
-				vddpa-supply = <&pm8921_l10>;
-				vdddig-supply = <&pm8921_lvs2>;
 			};
 
 			smd-edge {
-- 
2.39.2

[PATCH v4 31/38] ARM: dts: qcom: mdm9615: move RPM regulators to board files

[Dmitry Baryshkov]

The set of regulators available over the RPM requests is not a property
of the SoC. Move them to board files.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../boot/dts/qcom/qcom-mdm9615-wp8548.dtsi    | 136 ++++++++++++++++++
 arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi      | 134 -----------------
 2 files changed, 136 insertions(+), 134 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
index 27c3d92d9452..0dd52cac0e2e 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
@@ -134,6 +134,142 @@ &gsbi5_serial {
 	pinctrl-names = "default";
 };
 
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8018-regulators";
+
+		vin_lvs1-supply = <&pm8018_s3>;
+
+		vdd_l7-supply = <&pm8018_s4>;
+		vdd_l8-supply = <&pm8018_s3>;
+		vdd_l9_l10_l11_l12-supply = <&pm8018_s5>;
+
+		/* Buck SMPS */
+		pm8018_s1: s1 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s2: s2 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s3: s3 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s4: s4 {
+			regulator-min-microvolt = <2100000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s5: s5 {
+			regulator-always-on;
+			regulator-min-microvolt = <1350000>;
+			regulator-max-microvolt = <1350000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8018_l2: l2 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8018_l3: l3 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8018_l4: l4 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8018_l5: l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8018_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8018_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8018_l8: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8018_l9: l9 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8018_l10: l10 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8018_l11: l11 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8018_l12: l12 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8018_l13: l13 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8018_l14: l14 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8018_lvs1: lvs1 {
+			bias-pull-down;
+		};
+	};
+};
+
 &sdcc1 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
index e23ca6c42683..07e712e890f6 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
@@ -338,140 +338,6 @@ rpm: rpm@108000 {
 				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "ack", "err", "wakeup";
-
-			regulators {
-				compatible = "qcom,rpm-pm8018-regulators";
-
-				vin_lvs1-supply = <&pm8018_s3>;
-
-				vdd_l7-supply = <&pm8018_s4>;
-				vdd_l8-supply = <&pm8018_s3>;
-				vdd_l9_l10_l11_l12-supply = <&pm8018_s5>;
-
-				/* Buck SMPS */
-				pm8018_s1: s1 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s2: s2 {
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s3: s3 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s4: s4 {
-					regulator-min-microvolt = <2100000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s5: s5 {
-					regulator-always-on;
-					regulator-min-microvolt = <1350000>;
-					regulator-max-microvolt = <1350000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				/* PMOS LDO */
-				pm8018_l2: l2 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8018_l3: l3 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8018_l4: l4 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				pm8018_l5: l5 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				pm8018_l6: l6 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				pm8018_l7: l7 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8018_l8: l8 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				pm8018_l9: l9 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				pm8018_l10: l10 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8018_l11: l11 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8018_l12: l12 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8018_l13: l13 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8018_l14: l14 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				pm8018_lvs1: lvs1 {
-					bias-pull-down;
-				};
-			};
 		};
 	};
 };
-- 
2.39.2

[PATCH v4 32/38] ARM: dts: qcom: msm8660: move RPM regulators to board files

[Dmitry Baryshkov]

The set of regulators available over the RPM requests is not a property
of the SoC. Move them to board files.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../dts/qcom/qcom-apq8060-dragonboard.dts     | 141 ++++++++++++------
 arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts  |  10 ++
 arch/arm/boot/dts/qcom/qcom-msm8660.dtsi      |  66 --------
 3 files changed, 102 insertions(+), 115 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
index 10b8f529c337..8b70d4a59c7b 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
@@ -453,6 +453,8 @@ &rpm {
 	 * that means
 	 */
 	regulators-0 {
+		compatible = "qcom,rpm-pm8901-regulators";
+
 		vdd_l0-supply = <&pm8901_s4>;
 		vdd_l1-supply = <&vph>;
 		vdd_l2-supply = <&vph>;
@@ -470,57 +472,63 @@ regulators-0 {
 		lvs3_in-supply = <&pm8058_s2>;
 		mvs_in-supply = <&pm8058_s3>;
 
-		l0 {
+		pm8901_l0: l0 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
-		l1 {
+
+		pm8901_l1: l1 {
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;
 			bias-pull-down;
 		};
-		l2 {
+
+		pm8901_l2: l2 {
 			/* TMA340 requires strictly 3.3V */
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;
 			bias-pull-down;
 		};
-		l3 {
+
+		pm8901_l3: l3 {
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;
 			bias-pull-down;
 		};
-		l4 {
+
+		pm8901_l4: l4 {
 			regulator-min-microvolt = <2600000>;
 			regulator-max-microvolt = <2600000>;
 			bias-pull-down;
 		};
-		l5 {
+
+		pm8901_l5: l5 {
 			regulator-min-microvolt = <2850000>;
 			regulator-max-microvolt = <2850000>;
 			bias-pull-down;
 		};
-		l6 {
+
+		pm8901_l6: l6 {
 			regulator-min-microvolt = <2200000>;
 			regulator-max-microvolt = <2200000>;
 			bias-pull-down;
 		};
 
 		/* s0 and s1 are SAW regulators controlled over SPM */
-		s2 {
+		pm8901_s2: s2 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
 			qcom,switch-mode-frequency = <1600000>;
 			bias-pull-down;
 		};
-		s3 {
+		pm8901_s3: s3 {
 			regulator-min-microvolt = <1100000>;
 			regulator-max-microvolt = <1100000>;
 			qcom,switch-mode-frequency = <1600000>;
 			bias-pull-down;
 		};
-		s4 {
+		pm8901_s4: s4 {
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
 			qcom,switch-mode-frequency = <1600000>;
@@ -528,17 +536,22 @@ s4 {
 		};
 
 		/* LVS0 thru 3 and mvs are just switches */
-		lvs0 {
+		pm8901_lvs0: lvs0 {
 			regulator-always-on;
 		};
-		lvs1 { };
-		lvs2 { };
-		lvs3 { };
-		mvs { };
 
+		pm8901_lvs1: lvs1 { };
+
+		pm8901_lvs2: lvs2 { };
+
+		pm8901_lvs3: lvs3 { };
+
+		pm8901_mvs: mvs { };
 	};
 
 	regulators-1 {
+		compatible = "qcom,rpm-pm8058-regulators";
+
 		vdd_l0_l1_lvs-supply = <&pm8058_s3>;
 		vdd_l2_l11_l12-supply = <&vph>;
 		vdd_l3_l4_l5-supply = <&vph>;
@@ -560,144 +573,169 @@ regulators-1 {
 		vdd_s4-supply = <&vph>;
 		vdd_ncp-supply = <&vph>;
 
-		l0 {
+		pm8058_l0: l0 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
-		l1 {
+
+		pm8058_l1: l1 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
-		l2 {
+
+		pm8058_l2: l2 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <2600000>;
 			bias-pull-down;
 		};
-		l3 {
+
+		pm8058_l3: l3 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
-		l4 {
+
+		pm8058_l4: l4 {
 			regulator-min-microvolt = <2850000>;
 			regulator-max-microvolt = <2850000>;
 			bias-pull-down;
 		};
-		l5 {
+
+		pm8058_l5: l5 {
 			regulator-min-microvolt = <2850000>;
 			regulator-max-microvolt = <2850000>;
 			bias-pull-down;
 		};
-		l6 {
+
+		pm8058_l6: l6 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3600000>;
 			bias-pull-down;
 		};
-		l7 {
+
+		pm8058_l7: l7 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
-		l8 {
+
+		pm8058_l8: l8 {
 			regulator-min-microvolt = <2900000>;
 			regulator-max-microvolt = <3050000>;
 			bias-pull-down;
 		};
-		l9 {
+
+		pm8058_l9: l9 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
-		l10 {
+
+		pm8058_l10: l10 {
 			regulator-min-microvolt = <2600000>;
 			regulator-max-microvolt = <2600000>;
 			bias-pull-down;
 		};
-		l11 {
+
+		pm8058_l11: l11 {
 			regulator-min-microvolt = <1500000>;
 			regulator-max-microvolt = <1500000>;
 			bias-pull-down;
 		};
-		l12 {
+
+		pm8058_l12: l12 {
 			regulator-min-microvolt = <2900000>;
 			regulator-max-microvolt = <2900000>;
 			bias-pull-down;
 		};
-		l13 {
+
+		pm8058_l13: l13 {
 			regulator-min-microvolt = <2050000>;
 			regulator-max-microvolt = <2050000>;
 			bias-pull-down;
 		};
-		l14 {
+
+		pm8058_l14: l14 {
 			regulator-min-microvolt = <2850000>;
 			regulator-max-microvolt = <2850000>;
 		};
-		l15 {
+
+		pm8058_l15: l15 {
 			regulator-min-microvolt = <2850000>;
 			regulator-max-microvolt = <2850000>;
 			bias-pull-down;
 		};
-		l16 {
+
+		pm8058_l16: l16 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 			regulator-always-on;
 		};
-		l17 {
+
+		pm8058_l17: l17 {
 			// 1.5V according to schematic
 			regulator-min-microvolt = <2600000>;
 			regulator-max-microvolt = <2600000>;
 			bias-pull-down;
 		};
-		l18 {
+
+		pm8058_l18: l18 {
 			regulator-min-microvolt = <2200000>;
 			regulator-max-microvolt = <2200000>;
 			bias-pull-down;
 		};
-		l19 {
+
+		pm8058_l19: l19 {
 			regulator-min-microvolt = <2500000>;
 			regulator-max-microvolt = <2500000>;
 			bias-pull-down;
 		};
-		l20 {
+
+		pm8058_l20: l20 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			bias-pull-down;
 		};
-		l21 {
+
+		pm8058_l21: l21 {
 			// 1.1 V according to schematic
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 			regulator-always-on;
 		};
-		l22 {
+
+		pm8058_l22: l22 {
 			// 1.2 V according to schematic
 			regulator-min-microvolt = <1150000>;
 			regulator-max-microvolt = <1150000>;
 			bias-pull-down;
 		};
-		l23 {
+
+		pm8058_l23: l23 {
 			// Unused
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
-		l24 {
+
+		pm8058_l24: l24 {
 			// Unused
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
-		l25 {
+
+		pm8058_l25: l25 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			bias-pull-down;
 		};
 
-		s0 {
+		pm8058_s0: s0 {
 			// regulator-min-microvolt = <500000>;
 			// regulator-max-microvolt = <1325000>;
 			regulator-min-microvolt = <1100000>;
@@ -705,7 +743,8 @@ s0 {
 			qcom,switch-mode-frequency = <1600000>;
 			bias-pull-down;
 		};
-		s1 {
+
+		pm8058_s1: s1 {
 			// regulator-min-microvolt = <500000>;
 			// regulator-max-microvolt = <1250000>;
 			regulator-min-microvolt = <1100000>;
@@ -713,21 +752,24 @@ s1 {
 			qcom,switch-mode-frequency = <1600000>;
 			bias-pull-down;
 		};
-		s2 {
+
+		pm8058_s2: s2 {
 			// 1.3 V according to schematic
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1400000>;
 			qcom,switch-mode-frequency = <1600000>;
 			bias-pull-down;
 		};
-		s3 {
+
+		pm8058_s3: s3 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <1600000>;
 			regulator-always-on;
 			bias-pull-down;
 		};
-		s4 {
+
+		pm8058_s4: s4 {
 			regulator-min-microvolt = <2200000>;
 			regulator-max-microvolt = <2200000>;
 			qcom,switch-mode-frequency = <1600000>;
@@ -736,14 +778,15 @@ s4 {
 		};
 
 		/* LVS0 and LVS1 are just switches */
-		lvs0 {
+		pm8058_lvs0: lvs0 {
 			bias-pull-down;
 		};
-		lvs1 {
+
+		pm8058_lvs1: lvs1 {
 			bias-pull-down;
 		};
 
-		ncp {
+		pm8058_ncp: ncp {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			qcom,switch-mode-frequency = <1600000>;
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
index be2fbc1e0950..69fe651f564d 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
@@ -65,6 +65,16 @@ MATRIX_KEY(5, 4, KEY_MENU)
 	keypad,num-columns = <5>;
 };
 
+&rpm {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8901-regulators";
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8058-regulators";
+	};
+};
+
 /* eMMC */
 &sdcc1 {
 	vmmc-supply = <&vsdcc_fixed>;
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
index eef4712bbcc4..a7c245b9c8f9 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
@@ -347,72 +347,6 @@ rpmcc: clock-controller {
 				clocks = <&pxo_board>;
 				clock-names = "pxo";
 			};
-
-			regulators-0 {
-				compatible = "qcom,rpm-pm8901-regulators";
-
-				pm8901_l0: l0 {};
-				pm8901_l1: l1 {};
-				pm8901_l2: l2 {};
-				pm8901_l3: l3 {};
-				pm8901_l4: l4 {};
-				pm8901_l5: l5 {};
-				pm8901_l6: l6 {};
-
-				/* S0 and S1 Handled as SAW regulators by SPM */
-				pm8901_s2: s2 {};
-				pm8901_s3: s3 {};
-				pm8901_s4: s4 {};
-
-				pm8901_lvs0: lvs0 {};
-				pm8901_lvs1: lvs1 {};
-				pm8901_lvs2: lvs2 {};
-				pm8901_lvs3: lvs3 {};
-
-				pm8901_mvs: mvs {};
-			};
-
-			regulators-1 {
-				compatible = "qcom,rpm-pm8058-regulators";
-
-				pm8058_l0: l0 {};
-				pm8058_l1: l1 {};
-				pm8058_l2: l2 {};
-				pm8058_l3: l3 {};
-				pm8058_l4: l4 {};
-				pm8058_l5: l5 {};
-				pm8058_l6: l6 {};
-				pm8058_l7: l7 {};
-				pm8058_l8: l8 {};
-				pm8058_l9: l9 {};
-				pm8058_l10: l10 {};
-				pm8058_l11: l11 {};
-				pm8058_l12: l12 {};
-				pm8058_l13: l13 {};
-				pm8058_l14: l14 {};
-				pm8058_l15: l15 {};
-				pm8058_l16: l16 {};
-				pm8058_l17: l17 {};
-				pm8058_l18: l18 {};
-				pm8058_l19: l19 {};
-				pm8058_l20: l20 {};
-				pm8058_l21: l21 {};
-				pm8058_l22: l22 {};
-				pm8058_l23: l23 {};
-				pm8058_l24: l24 {};
-				pm8058_l25: l25 {};
-
-				pm8058_s0: s0 {};
-				pm8058_s1: s1 {};
-				pm8058_s2: s2 {};
-				pm8058_s3: s3 {};
-				pm8058_s4: s4 {};
-
-				pm8058_lvs0: lvs0 {};
-				pm8058_lvs1: lvs1 {};
-
-				pm8058_ncp: ncp {};
-			};
 		};
 
 		amba {
-- 
2.39.2

[PATCH v4 33/38] ARM: dts: qcom: msm8960: drop useless rpm regulators node

[Dmitry Baryshkov]

The set of regulators available over the RPM requests is not a property
of the SoC. The only msm8960 board file (qcom-msm8960-cdp) also defines
this node together with the compatible string. Drop the useless device
node.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-msm8960.dtsi | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
index 774f507fa25a..f420740e068e 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -200,10 +200,6 @@ rpm: rpm@108000 {
 				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "ack", "err", "wakeup";
-
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-			};
 		};
 
 		acc0: clock-controller@2088000 {
-- 
2.39.2

[PATCH v4 34/38] ARM: dts: qcom: msm8974: move regulators to board files

[Dmitry Baryshkov]

The vph-pwr and boost regulators (even if they are unified by design)
are not a property of SoC, so move them to board files.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../dts/qcom/qcom-apq8074-dragonboard.dts     | 27 +++++++++++++++++++
 .../qcom-msm8974-lge-nexus5-hammerhead.dts    | 27 +++++++++++++++++++
 .../qcom/qcom-msm8974-sony-xperia-rhine.dtsi  | 27 +++++++++++++++++++
 arch/arm/boot/dts/qcom/qcom-msm8974.dtsi      | 27 -------------------
 .../qcom/qcom-msm8974pro-fairphone-fp2.dts    | 27 +++++++++++++++++++
 .../qcom/qcom-msm8974pro-oneplus-bacon.dts    | 27 +++++++++++++++++++
 .../dts/qcom/qcom-msm8974pro-samsung-klte.dts | 10 ++++++-
 ...-msm8974pro-sony-xperia-shinano-castor.dts | 27 +++++++++++++++++++
 8 files changed, 171 insertions(+), 28 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
index 950fa652f985..d7fb3e0e8886 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
@@ -49,6 +49,33 @@ mpss_region: mpss@ac00000 {
 			no-map;
 		};
 	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
 };
 
 &blsp1_uart2 {
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
index da99f770d4f5..ca402b4a68bd 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -60,6 +60,33 @@ vibrator {
 		enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
 	};
 
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+
 	vreg_wlan: wlan-regulator {
 		compatible = "regulator-fixed";
 
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
index 23ae474698aa..a43341ae4495 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
@@ -65,6 +65,33 @@ ramoops@3e8e0000 {
 			pmsg-size = <0x80000>;
 		};
 	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
 };
 
 &blsp1_i2c2 {
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
index 706fef53767e..d54be72fe3b2 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
@@ -2376,31 +2376,4 @@ timer {
 			     <GIC_PPI 1 0xf08>;
 		clock-frequency = <19200000>;
 	};
-
-	vreg_boost: vreg-boost {
-		compatible = "regulator-fixed";
-
-		regulator-name = "vreg-boost";
-		regulator-min-microvolt = <3150000>;
-		regulator-max-microvolt = <3150000>;
-
-		regulator-always-on;
-		regulator-boot-on;
-
-		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&boost_bypass_n_pin>;
-	};
-
-	vreg_vph_pwr: vreg-vph-pwr {
-		compatible = "regulator-fixed";
-		regulator-name = "vph-pwr";
-
-		regulator-min-microvolt = <3600000>;
-		regulator-max-microvolt = <3600000>;
-
-		regulator-always-on;
-	};
 };
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
index 6c4153689b39..66c422004dcd 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
@@ -57,6 +57,33 @@ vibrator {
 		enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
 		vcc-supply = <&pm8941_l18>;
 	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
 };
 
 &blsp1_i2c2 {
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
index c0ca264d8140..6d1412aec45a 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
@@ -51,6 +51,33 @@ event-hall-sensor {
 			debounce-interval = <150>;
 		};
 	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
 };
 
 &blsp1_i2c1 {
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
index 325feb89b343..ca3aa16b4b10 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
@@ -155,7 +155,15 @@ vreg_panel: panel-regulator {
 		enable-active-high;
 	};
 
-	/delete-node/ vreg-boost;
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
 };
 
 &blsp1_i2c2 {
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
index 0798cce3dbea..818ff5835031 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
@@ -84,6 +84,33 @@ vreg_vsp: lcd-dcdc-regulator {
 		pinctrl-0 = <&lcd_dcdc_en_pin_a>;
 	};
 
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+
 	vreg_wlan: wlan-regulator {
 		compatible = "regulator-fixed";
 
-- 
2.39.2

[PATCH v4 35/38] ARM: dts: qcom: pm8921: Disable keypad by default

[Dmitry Baryshkov]

Since keypad is used only by some devices, disable it by default and enable explicitly.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/pm8921.dtsi          | 1 +
 arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts | 2 ++
 2 files changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/qcom/pm8921.dtsi b/arch/arm/boot/dts/qcom/pm8921.dtsi
index 360a179670c5..058962af3005 100644
--- a/arch/arm/boot/dts/qcom/pm8921.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8921.dtsi
@@ -43,6 +43,7 @@ pm8921_keypad: keypad@148 {
 			debounce = <15>;
 			scan-delay = <32>;
 			row-hold = <91500>;
+			status = "disabled";
 		};
 
 		pm8921_gpio: gpio@150 {
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
index a5ea4843db43..36f4c997b0b3 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
@@ -102,6 +102,8 @@ MATRIX_KEY(0, 3, KEY_CAMERA)
 		>;
 	keypad,num-rows = <1>;
 	keypad,num-columns = <5>;
+
+	status = "okay";
 };
 
 &rpm {
-- 
2.39.2

[PATCH v4 36/38] ARM: dts: qcom: apq8060-dragonboard: rename mpp ADC channels to adc-channel

[Dmitry Baryshkov]

Use generic `adc-channel@N' node names for board-specific ADC channels
(routed to MPP pins) to follow the schema.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
index 8b70d4a59c7b..bf2527941917 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
@@ -998,23 +998,27 @@ &pm8058_xoadc {
 	xoadc-ref-supply = <&pm8058_l18>;
 
 	/* Board-specific channels */
-	mpp5@5 {
+	adc-channel@5 {
 		/* Connected to AOUT of ALS sensor */
 		reg = <0x00 0x05>;
 	};
-	mpp6@6 {
+
+	adc-channel@6 {
 		/* Connected to test point TP43 */
 		reg = <0x00 0x06>;
 	};
-	mpp7@7 {
+
+	adc-channel@7 {
 		/* Connected to battery thermistor */
 		reg = <0x00 0x07>;
 	};
-	mpp8@8 {
+
+	adc-channel@8 {
 		/* Connected to battery ID detector */
 		reg = <0x00 0x08>;
 	};
-	mpp9@9 {
+
+	adc-channel@9 {
 		/* Connected to XO thermistor */
 		reg = <0x00 0x09>;
 	};
-- 
2.39.2

[PATCH v4 37/38] ARM: dts: qcom: ipq8064: drop qcom, prefix from SSBI node name

[Dmitry Baryshkov]

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
index 6198f42f6a9c..c3677440b786 100644
--- a/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
@@ -366,7 +366,7 @@ rpmcc: clock-controller {
 			};
 		};
 
-		qcom,ssbi@500000 {
+		ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-- 
2.39.2

[PATCH v4 38/38] ARM: dts: qcom: mdm9615: drop qcom, prefix from SSBI node name

[Dmitry Baryshkov]

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
index 07e712e890f6..b02336bd8370 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
@@ -258,7 +258,7 @@ gsbi5_serial: serial@16440000 {
 			};
 		};
 
-		ssbi: qcom,ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-- 
2.39.2