* [PATCH v10 1/6] dt-bindings: mfd: add pf1550
2025-08-20 20:44 [PATCH v10 0/6] add support for pf1550 PMIC MFD-based drivers Samuel Kayode via B4 Relay
@ 2025-08-20 20:44 ` Samuel Kayode via B4 Relay
2025-08-20 20:44 ` [PATCH v10 2/6] mfd: pf1550: add core driver Samuel Kayode via B4 Relay
` (4 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Samuel Kayode via B4 Relay @ 2025-08-20 20:44 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Liam Girdwood, Mark Brown, Dmitry Torokhov, Sebastian Reichel,
Frank Li
Cc: imx, devicetree, linux-kernel, linux-input, linux-pm, Abel Vesa,
Abel Vesa, Robin Gong, Robin Gong, Enric Balletbo i Serra,
Sean Nyekjaer, Christophe JAILLET, Samuel Kayode, Abel Vesa,
Krzysztof Kozlowski
From: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
Add a DT binding document for pf1550 PMIC. This describes the core mfd
device along with its children: regulators, charger and onkey.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
---
v10:
- Add regulator-state-mem to examples
v9:
- Add regulator suspend bindings in example
- Add binding for disabling onkey power down
- Fix thermal regulation temperature range
v5:
- Address Krzystof's feedback:
- Drop monitored battery ref already included in power supply schema
- Move `additionalProperties` close to `type` for regulator
- Drop unneccessary |
- Change `additionalProperties` to `unevaluatedProperties` for the
PMIC
v4:
- Address Krzystof's feedback:
- Filename changed to nxp,pf1550.yaml
- Replace Freescale with NXP
- Define include before battery-cell
- Drop operating-range-celsius in example since
nxp,thermal-regulation-celsisus already exists
- Not sure if there is similar binding to thermal-regulation...
for regulating temperature on thermal-zones? @Sebastian and @Krzysztof
v3:
- Address Krzysztof's feedback:
- Fold charger and onkey objects
- Drop compatible for sub-devices: onkey, charger and regulator.
- Drop constant voltage property already included in
monitored-battery
- Fix whitespace warnings
- Fix license
v2:
- Add yamls for the PMIC and the sub-devices
---
.../devicetree/bindings/mfd/nxp,pf1550.yaml | 161 +++++++++++++++++++++
1 file changed, 161 insertions(+)
diff --git a/Documentation/devicetree/bindings/mfd/nxp,pf1550.yaml b/Documentation/devicetree/bindings/mfd/nxp,pf1550.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..e50dc44252c60063463295c5ec3e3c90d1592ec2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/nxp,pf1550.yaml
@@ -0,0 +1,161 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/nxp,pf1550.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP PF1550 Power Management IC
+
+maintainers:
+ - Samuel Kayode <samuel.kayode@savoirfairelinux.com>
+
+description:
+ PF1550 PMIC provides battery charging and power supply for low power IoT and
+ wearable applications. This device consists of an i2c controlled MFD that
+ includes regulators, battery charging and an onkey/power button.
+
+$ref: /schemas/power/supply/power-supply.yaml
+
+properties:
+ compatible:
+ const: nxp,pf1550
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ wakeup-source: true
+
+ regulators:
+ type: object
+ additionalProperties: false
+
+ patternProperties:
+ "^(ldo[1-3]|sw[1-3]|vrefddr)$":
+ type: object
+ $ref: /schemas/regulator/regulator.yaml
+ description:
+ regulator configuration for ldo1-3, buck converters(sw1-3)
+ and DDR termination reference voltage (vrefddr)
+ unevaluatedProperties: false
+
+ monitored-battery:
+ description: |
+ A phandle to a monitored battery node that contains a valid value
+ for:
+ constant-charge-voltage-max-microvolt.
+
+ nxp,thermal-regulation-celsius:
+ description:
+ Temperature threshold for thermal regulation of charger in celsius.
+ enum: [ 80, 95, 110, 125 ]
+
+ nxp,min-system-microvolt:
+ description:
+ System specific lower limit voltage.
+ enum: [ 3500000, 3700000, 4300000 ]
+
+ nxp,disable-key-power:
+ type: boolean
+ description:
+ Disable power-down using a long key-press. The onkey driver will remove
+ support for the KEY_POWER key press when triggered using a long press of
+ the onkey.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/input/linux-event-codes.h>
+
+ battery: battery-cell {
+ compatible = "simple-battery";
+ constant-charge-voltage-max-microvolt = <4400000>;
+ };
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@8 {
+ compatible = "nxp,pf1550";
+ reg = <0x8>;
+
+ interrupt-parent = <&gpio1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ wakeup-source;
+ monitored-battery = <&battery>;
+ nxp,min-system-microvolt = <4300000>;
+ nxp,thermal-regulation-celsius = <80>;
+
+ regulators {
+ sw1_reg: sw1 {
+ regulator-name = "sw1";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1387500>;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-min-microvolt = <1270000>;
+ };
+ };
+
+ sw2_reg: sw2 {
+ regulator-name = "sw2";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1387500>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ sw3_reg: sw3 {
+ regulator-name = "sw3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vldo1_reg: ldo1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vldo2_reg: ldo2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vldo3_reg: ldo3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+ };
--
2.50.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v10 2/6] mfd: pf1550: add core driver
2025-08-20 20:44 [PATCH v10 0/6] add support for pf1550 PMIC MFD-based drivers Samuel Kayode via B4 Relay
2025-08-20 20:44 ` [PATCH v10 1/6] dt-bindings: mfd: add pf1550 Samuel Kayode via B4 Relay
@ 2025-08-20 20:44 ` Samuel Kayode via B4 Relay
2025-08-20 20:44 ` [PATCH v10 3/6] regulator: pf1550: add support for regulator Samuel Kayode via B4 Relay
` (3 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Samuel Kayode via B4 Relay @ 2025-08-20 20:44 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Liam Girdwood, Mark Brown, Dmitry Torokhov, Sebastian Reichel,
Frank Li
Cc: imx, devicetree, linux-kernel, linux-input, linux-pm, Abel Vesa,
Abel Vesa, Robin Gong, Robin Gong, Enric Balletbo i Serra,
Sean Nyekjaer, Christophe JAILLET, Samuel Kayode, Abel Vesa,
Frank Li
From: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
Add the core driver for pf1550 PMIC. There are 3 subdevices for which the
drivers will be added in subsequent patches.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
---
v10:
- Address Lee's feedback:
- Change dvsX_enb to dvsX_enable
- Add new line where necessary
- Can use 100 chars in a line
- Begin comments with uppercase
- Rearrange members of struct pf1550_ddata
- Add support for disabling onkey shutting down system
v9:
- Requested by Sean:
- Add support for SW1 DVS enable/disable
- Use consistent whitespace
- Adjust commenting and log messages of the read_otp function
v8:
- Address Lee's feedback:
- Drop `mfd` from driver description and comments
- Add module name in Kconfig
- Fix license commenting
- Drop filenames from comments
- Drop unnecessary tabbing
- Alphabetical ordering of includes
- Remove magic numbers
- Add comments for pf1550_read_otp function
- Fix log error message in pf1550_read_otp
- Drop pf1550_add_child_device function
- Start comments with upper case
- Rename pf1550_dev to pf1550_ddata
- Drop i2c member in struct pf1550_ddata/pf1550_dev
- Use more helpful log message when device id not recognized
- Fix dvs_enb: when bit is set the DVS is disabled and when bit is clear the
DVS is enabled
- Verified the PM_OPS suspend and resume do act as expected
v7:
- Address Frank's feedback:
- Ensure reverse christmas tree order for local variable definitions
- Drop unnecessary driver data definition in id table
v6:
- Address Frank's feedback:
- Ensure lowercase when defining register addresses
- Use GENMASK macro for masking
- Hardcode IRQ flags in pf1550_add_child_device
- Add dvs_enb variable for SW2 regulator
- Drop chip type variable
v5:
- Use top level interrupt to manage interrupts for the sub-drivers as
recommended by Mark Brown. The regmap_irq_sub_irq_map would have been used
if not for the irregular charger irq address. For all children, the mask
register is directly after the irq register (i.e., 0x08, 0x09) except
for the charger: 0x80, 0x82. Meaning .mask_base would be applicable
for all but the charger
- Fix bad offset for temperature interrupts of regulator
v4:
- Use struct resource to define irq so platform_get_irq can be used in
children as suggested by Dmitry
- Let mfd_add_devices create the mappings for the interrupts
- ack_base and init_ack_masked defined for charger and regulator irq
chips
- No need to define driver_data in table id
v3:
- Address Dmitry's feedback:
- Place Table IDs next to each other
- Drop of_match_ptr
- Replace dev_err with dev_err_probe in probe method
- Drop useless log in probe
- Map all irqs instead of doing it in the sub-devices as recommended by
Dmitry.
v2:
- Address feedback from Enric Balletbo Serra
---
drivers/mfd/Kconfig | 16 ++
drivers/mfd/Makefile | 2 +
drivers/mfd/pf1550.c | 367 +++++++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/pf1550.h | 273 +++++++++++++++++++++++++++++++++
4 files changed, 658 insertions(+)
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 6fb3768e3d71cbb5c81f63de36cdb2d27a0a7726..14e21f0e239b4a609b01c59435f39abaa41dce14 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -558,6 +558,22 @@ config MFD_MX25_TSADC
i.MX25 processors. They consist of a conversion queue for general
purpose ADC and a queue for Touchscreens.
+config MFD_PF1550
+ tristate "NXP PF1550 PMIC Support"
+ depends on I2C=y && OF
+ select MFD_CORE
+ select REGMAP_I2C
+ select REGMAP_IRQ
+ help
+ Say yes here to add support for NXP PF1550. This is a companion Power
+ Management IC with regulators, onkey, and charger control on chip.
+ This driver provides common support for accessing the device;
+ additional drivers must be enabled in order to use the functionality
+ of the device.
+
+ This driver can also be built as a module and if so will be called
+ pf1550.
+
config MFD_HI6421_PMIC
tristate "HiSilicon Hi6421 PMU/Codec IC"
depends on OF
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 79495f9f3457b8a666646ec9671861c64d7939e1..8bf712081deaafa554940c1aac0c317a2dcbbfeb 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -120,6 +120,8 @@ obj-$(CONFIG_MFD_MC13XXX) += mc13xxx-core.o
obj-$(CONFIG_MFD_MC13XXX_SPI) += mc13xxx-spi.o
obj-$(CONFIG_MFD_MC13XXX_I2C) += mc13xxx-i2c.o
+obj-$(CONFIG_MFD_PF1550) += pf1550.o
+
obj-$(CONFIG_MFD_CORE) += mfd-core.o
ocelot-soc-objs := ocelot-core.o ocelot-spi.o
diff --git a/drivers/mfd/pf1550.c b/drivers/mfd/pf1550.c
new file mode 100644
index 0000000000000000000000000000000000000000..c4f567c055640662cc2db742917cc87cf9cabb5f
--- /dev/null
+++ b/drivers/mfd/pf1550.c
@@ -0,0 +1,367 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Core driver for the PF1550
+ *
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Robin Gong <yibin.gong@freescale.com>
+ *
+ * Portions Copyright (c) 2025 Savoir-faire Linux Inc.
+ * Samuel Kayode <samuel.kayode@savoirfairelinux.com>
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/pf1550.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+
+static const struct regmap_config pf1550_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = PF1550_PMIC_REG_END,
+};
+
+static const struct regmap_irq pf1550_irqs[] = {
+ REGMAP_IRQ_REG(PF1550_IRQ_CHG, 0, IRQ_CHG),
+ REGMAP_IRQ_REG(PF1550_IRQ_REGULATOR, 0, IRQ_REGULATOR),
+ REGMAP_IRQ_REG(PF1550_IRQ_ONKEY, 0, IRQ_ONKEY),
+};
+
+static const struct regmap_irq_chip pf1550_irq_chip = {
+ .name = "pf1550",
+ .status_base = PF1550_PMIC_REG_INT_CATEGORY,
+ .init_ack_masked = 1,
+ .num_regs = 1,
+ .irqs = pf1550_irqs,
+ .num_irqs = ARRAY_SIZE(pf1550_irqs),
+};
+
+static const struct regmap_irq pf1550_regulator_irqs[] = {
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_SW1_LS, 0, PMIC_IRQ_SW1_LS),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_SW2_LS, 0, PMIC_IRQ_SW2_LS),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_SW3_LS, 0, PMIC_IRQ_SW3_LS),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_SW1_HS, 3, PMIC_IRQ_SW1_HS),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_SW2_HS, 3, PMIC_IRQ_SW2_HS),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_SW3_HS, 3, PMIC_IRQ_SW3_HS),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_LDO1_FAULT, 16, PMIC_IRQ_LDO1_FAULT),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_LDO2_FAULT, 16, PMIC_IRQ_LDO2_FAULT),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_LDO3_FAULT, 16, PMIC_IRQ_LDO3_FAULT),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_TEMP_110, 24, PMIC_IRQ_TEMP_110),
+ REGMAP_IRQ_REG(PF1550_PMIC_IRQ_TEMP_125, 24, PMIC_IRQ_TEMP_125),
+};
+
+static const struct regmap_irq_chip pf1550_regulator_irq_chip = {
+ .name = "pf1550-regulator",
+ .status_base = PF1550_PMIC_REG_SW_INT_STAT0,
+ .ack_base = PF1550_PMIC_REG_SW_INT_STAT0,
+ .mask_base = PF1550_PMIC_REG_SW_INT_MASK0,
+ .use_ack = 1,
+ .init_ack_masked = 1,
+ .num_regs = 25,
+ .irqs = pf1550_regulator_irqs,
+ .num_irqs = ARRAY_SIZE(pf1550_regulator_irqs),
+};
+
+static const struct resource regulator_resources[] = {
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_SW1_LS),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_SW2_LS),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_SW3_LS),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_SW1_HS),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_SW2_HS),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_SW3_HS),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_LDO1_FAULT),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_LDO2_FAULT),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_LDO3_FAULT),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_TEMP_110),
+ DEFINE_RES_IRQ(PF1550_PMIC_IRQ_TEMP_125),
+};
+
+static const struct regmap_irq pf1550_onkey_irqs[] = {
+ REGMAP_IRQ_REG(PF1550_ONKEY_IRQ_PUSHI, 0, ONKEY_IRQ_PUSHI),
+ REGMAP_IRQ_REG(PF1550_ONKEY_IRQ_1SI, 0, ONKEY_IRQ_1SI),
+ REGMAP_IRQ_REG(PF1550_ONKEY_IRQ_2SI, 0, ONKEY_IRQ_2SI),
+ REGMAP_IRQ_REG(PF1550_ONKEY_IRQ_3SI, 0, ONKEY_IRQ_3SI),
+ REGMAP_IRQ_REG(PF1550_ONKEY_IRQ_4SI, 0, ONKEY_IRQ_4SI),
+ REGMAP_IRQ_REG(PF1550_ONKEY_IRQ_8SI, 0, ONKEY_IRQ_8SI),
+};
+
+static const struct regmap_irq_chip pf1550_onkey_irq_chip = {
+ .name = "pf1550-onkey",
+ .status_base = PF1550_PMIC_REG_ONKEY_INT_STAT0,
+ .ack_base = PF1550_PMIC_REG_ONKEY_INT_STAT0,
+ .mask_base = PF1550_PMIC_REG_ONKEY_INT_MASK0,
+ .use_ack = 1,
+ .init_ack_masked = 1,
+ .num_regs = 1,
+ .irqs = pf1550_onkey_irqs,
+ .num_irqs = ARRAY_SIZE(pf1550_onkey_irqs),
+};
+
+static const struct resource onkey_resources[] = {
+ DEFINE_RES_IRQ(PF1550_ONKEY_IRQ_PUSHI),
+ DEFINE_RES_IRQ(PF1550_ONKEY_IRQ_1SI),
+ DEFINE_RES_IRQ(PF1550_ONKEY_IRQ_2SI),
+ DEFINE_RES_IRQ(PF1550_ONKEY_IRQ_3SI),
+ DEFINE_RES_IRQ(PF1550_ONKEY_IRQ_4SI),
+ DEFINE_RES_IRQ(PF1550_ONKEY_IRQ_8SI),
+};
+
+static const struct regmap_irq pf1550_charger_irqs[] = {
+ REGMAP_IRQ_REG(PF1550_CHARG_IRQ_BAT2SOCI, 0, CHARG_IRQ_BAT2SOCI),
+ REGMAP_IRQ_REG(PF1550_CHARG_IRQ_BATI, 0, CHARG_IRQ_BATI),
+ REGMAP_IRQ_REG(PF1550_CHARG_IRQ_CHGI, 0, CHARG_IRQ_CHGI),
+ REGMAP_IRQ_REG(PF1550_CHARG_IRQ_VBUSI, 0, CHARG_IRQ_VBUSI),
+ REGMAP_IRQ_REG(PF1550_CHARG_IRQ_THMI, 0, CHARG_IRQ_THMI),
+};
+
+static const struct regmap_irq_chip pf1550_charger_irq_chip = {
+ .name = "pf1550-charger",
+ .status_base = PF1550_CHARG_REG_CHG_INT,
+ .ack_base = PF1550_CHARG_REG_CHG_INT,
+ .mask_base = PF1550_CHARG_REG_CHG_INT_MASK,
+ .use_ack = 1,
+ .init_ack_masked = 1,
+ .num_regs = 1,
+ .irqs = pf1550_charger_irqs,
+ .num_irqs = ARRAY_SIZE(pf1550_charger_irqs),
+};
+
+static const struct resource charger_resources[] = {
+ DEFINE_RES_IRQ(PF1550_CHARG_IRQ_BAT2SOCI),
+ DEFINE_RES_IRQ(PF1550_CHARG_IRQ_BATI),
+ DEFINE_RES_IRQ(PF1550_CHARG_IRQ_CHGI),
+ DEFINE_RES_IRQ(PF1550_CHARG_IRQ_VBUSI),
+ DEFINE_RES_IRQ(PF1550_CHARG_IRQ_THMI),
+};
+
+static const struct mfd_cell pf1550_regulator_cell = {
+ .name = "pf1550-regulator",
+ .num_resources = ARRAY_SIZE(regulator_resources),
+ .resources = regulator_resources,
+};
+
+static const struct mfd_cell pf1550_onkey_cell = {
+ .name = "pf1550-onkey",
+ .num_resources = ARRAY_SIZE(onkey_resources),
+ .resources = onkey_resources,
+};
+
+static const struct mfd_cell pf1550_charger_cell = {
+ .name = "pf1550-charger",
+ .num_resources = ARRAY_SIZE(charger_resources),
+ .resources = charger_resources,
+};
+
+/*
+ * The PF1550 is shipped in variants of A0, A1,...A9. Each variant defines a
+ * configuration of the PMIC in a One-Time Programmable (OTP) memory.
+ * This memory is accessed indirectly by writing valid keys to specific
+ * registers of the PMIC. To read the OTP memory after writing the valid keys,
+ * the OTP register address to be read is written to pf1550 register 0xc4 and
+ * its value read from pf1550 register 0xc5.
+ */
+static int pf1550_read_otp(const struct pf1550_ddata *pf1550, unsigned int index,
+ unsigned int *val)
+{
+ int ret = 0;
+
+ ret = regmap_write(pf1550->regmap, PF1550_PMIC_REG_KEY, PF1550_OTP_PMIC_KEY);
+ if (ret)
+ goto read_err;
+
+ ret = regmap_write(pf1550->regmap, PF1550_CHARG_REG_CHGR_KEY2, PF1550_OTP_CHGR_KEY);
+ if (ret)
+ goto read_err;
+
+ ret = regmap_write(pf1550->regmap, PF1550_TEST_REG_KEY3, PF1550_OTP_TEST_KEY);
+ if (ret)
+ goto read_err;
+
+ ret = regmap_write(pf1550->regmap, PF1550_TEST_REG_FMRADDR, index);
+ if (ret)
+ goto read_err;
+
+ ret = regmap_read(pf1550->regmap, PF1550_TEST_REG_FMRDATA, val);
+ if (ret)
+ goto read_err;
+
+ return 0;
+
+read_err:
+ return dev_err_probe(pf1550->dev, ret, "OTP reg %x not found!\n", index);
+}
+
+static int pf1550_i2c_probe(struct i2c_client *i2c)
+{
+ const struct mfd_cell *regulator = &pf1550_regulator_cell;
+ const struct mfd_cell *charger = &pf1550_charger_cell;
+ const struct mfd_cell *onkey = &pf1550_onkey_cell;
+ unsigned int reg_data = 0, otp_data = 0;
+ struct pf1550_ddata *pf1550;
+ struct irq_domain *domain;
+ int irq, ret = 0;
+
+ pf1550 = devm_kzalloc(&i2c->dev, sizeof(*pf1550), GFP_KERNEL);
+ if (!pf1550)
+ return -ENOMEM;
+
+ i2c_set_clientdata(i2c, pf1550);
+ pf1550->dev = &i2c->dev;
+ pf1550->irq = i2c->irq;
+
+ pf1550->regmap = devm_regmap_init_i2c(i2c, &pf1550_regmap_config);
+ if (IS_ERR(pf1550->regmap))
+ return dev_err_probe(pf1550->dev, PTR_ERR(pf1550->regmap),
+ "failed to allocate register map\n");
+
+ ret = regmap_read(pf1550->regmap, PF1550_PMIC_REG_DEVICE_ID, ®_data);
+ if (ret < 0)
+ return dev_err_probe(pf1550->dev, ret, "cannot read chip ID\n");
+ if (reg_data != PF1550_DEVICE_ID)
+ return dev_err_probe(pf1550->dev, -ENODEV, "invalid device ID: 0x%02x\n", reg_data);
+
+ /* Regulator DVS for SW2 */
+ ret = pf1550_read_otp(pf1550, PF1550_OTP_SW2_SW3, &otp_data);
+ if (ret)
+ return ret;
+
+ /* When clear, DVS should be enabled */
+ if (!(otp_data & OTP_SW2_DVS_ENB))
+ pf1550->dvs2_enable = true;
+
+ /* Regulator DVS for SW1 */
+ ret = pf1550_read_otp(pf1550, PF1550_OTP_SW1_SW2, &otp_data);
+ if (ret)
+ return ret;
+
+ if (!(otp_data & OTP_SW1_DVS_ENB))
+ pf1550->dvs1_enable = true;
+
+ /* Add top level interrupts */
+ ret = devm_regmap_add_irq_chip(pf1550->dev, pf1550->regmap, pf1550->irq,
+ IRQF_ONESHOT | IRQF_SHARED |
+ IRQF_TRIGGER_FALLING,
+ 0, &pf1550_irq_chip,
+ &pf1550->irq_data);
+ if (ret)
+ return ret;
+
+ /* Add regulator */
+ irq = regmap_irq_get_virq(pf1550->irq_data, PF1550_IRQ_REGULATOR);
+ if (irq < 0)
+ return dev_err_probe(pf1550->dev, irq,
+ "Failed to get parent vIRQ(%d) for chip %s\n",
+ PF1550_IRQ_REGULATOR, pf1550_irq_chip.name);
+
+ ret = devm_regmap_add_irq_chip(pf1550->dev, pf1550->regmap, irq,
+ IRQF_ONESHOT | IRQF_SHARED |
+ IRQF_TRIGGER_FALLING, 0,
+ &pf1550_regulator_irq_chip,
+ &pf1550->irq_data_regulator);
+ if (ret)
+ return dev_err_probe(pf1550->dev, ret, "Failed to add %s IRQ chip\n",
+ pf1550_regulator_irq_chip.name);
+
+ domain = regmap_irq_get_domain(pf1550->irq_data_regulator);
+
+ ret = devm_mfd_add_devices(pf1550->dev, PLATFORM_DEVID_NONE, regulator, 1, NULL, 0, domain);
+ if (ret)
+ return ret;
+
+ /* Add onkey */
+ irq = regmap_irq_get_virq(pf1550->irq_data, PF1550_IRQ_ONKEY);
+ if (irq < 0)
+ return dev_err_probe(pf1550->dev, irq,
+ "Failed to get parent vIRQ(%d) for chip %s\n",
+ PF1550_IRQ_ONKEY, pf1550_irq_chip.name);
+
+ ret = devm_regmap_add_irq_chip(pf1550->dev, pf1550->regmap, irq,
+ IRQF_ONESHOT | IRQF_SHARED |
+ IRQF_TRIGGER_FALLING, 0,
+ &pf1550_onkey_irq_chip,
+ &pf1550->irq_data_onkey);
+ if (ret)
+ return dev_err_probe(pf1550->dev, ret, "Failed to add %s IRQ chip\n",
+ pf1550_onkey_irq_chip.name);
+
+ domain = regmap_irq_get_domain(pf1550->irq_data_onkey);
+
+ ret = devm_mfd_add_devices(pf1550->dev, PLATFORM_DEVID_NONE, onkey, 1, NULL, 0, domain);
+ if (ret)
+ return ret;
+
+ /* Add battery charger */
+ irq = regmap_irq_get_virq(pf1550->irq_data, PF1550_IRQ_CHG);
+ if (irq < 0)
+ return dev_err_probe(pf1550->dev, irq,
+ "Failed to get parent vIRQ(%d) for chip %s\n",
+ PF1550_IRQ_CHG, pf1550_irq_chip.name);
+
+ ret = devm_regmap_add_irq_chip(pf1550->dev, pf1550->regmap, irq,
+ IRQF_ONESHOT | IRQF_SHARED |
+ IRQF_TRIGGER_FALLING, 0,
+ &pf1550_charger_irq_chip,
+ &pf1550->irq_data_charger);
+ if (ret)
+ return dev_err_probe(pf1550->dev, ret, "Failed to add %s IRQ chip\n",
+ pf1550_charger_irq_chip.name);
+
+ domain = regmap_irq_get_domain(pf1550->irq_data_charger);
+
+ return devm_mfd_add_devices(pf1550->dev, PLATFORM_DEVID_NONE, charger, 1, NULL, 0, domain);
+}
+
+static int pf1550_suspend(struct device *dev)
+{
+ struct pf1550_ddata *pf1550 = dev_get_drvdata(dev);
+
+ if (device_may_wakeup(dev)) {
+ enable_irq_wake(pf1550->irq);
+ disable_irq(pf1550->irq);
+ }
+
+ return 0;
+}
+
+static int pf1550_resume(struct device *dev)
+{
+ struct pf1550_ddata *pf1550 = dev_get_drvdata(dev);
+
+ if (device_may_wakeup(dev)) {
+ disable_irq_wake(pf1550->irq);
+ enable_irq(pf1550->irq);
+ }
+
+ return 0;
+}
+static DEFINE_SIMPLE_DEV_PM_OPS(pf1550_pm, pf1550_suspend, pf1550_resume);
+
+static const struct i2c_device_id pf1550_i2c_id[] = {
+ { "pf1550" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, pf1550_i2c_id);
+
+static const struct of_device_id pf1550_dt_match[] = {
+ { .compatible = "nxp,pf1550" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, pf1550_dt_match);
+
+static struct i2c_driver pf1550_i2c_driver = {
+ .driver = {
+ .name = "pf1550",
+ .pm = pm_sleep_ptr(&pf1550_pm),
+ .of_match_table = pf1550_dt_match,
+ },
+ .probe = pf1550_i2c_probe,
+ .id_table = pf1550_i2c_id,
+};
+module_i2c_driver(pf1550_i2c_driver);
+
+MODULE_DESCRIPTION("NXP PF1550 core driver");
+MODULE_AUTHOR("Robin Gong <yibin.gong@freescale.com>");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/pf1550.h b/include/linux/mfd/pf1550.h
new file mode 100644
index 0000000000000000000000000000000000000000..7cb2340ff2bd92883a709806da58601daaf98a88
--- /dev/null
+++ b/include/linux/mfd/pf1550.h
@@ -0,0 +1,273 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Declarations for the PF1550 PMIC
+ *
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Robin Gong <yibin.gong@freescale.com>
+ *
+ * Portions Copyright (c) 2025 Savoir-faire Linux Inc.
+ * Samuel Kayode <samuel.kayode@savoirfairelinux.com>
+ */
+
+#ifndef __LINUX_MFD_PF1550_H
+#define __LINUX_MFD_PF1550_H
+
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+
+enum pf1550_pmic_reg {
+ /* PMIC regulator part */
+ PF1550_PMIC_REG_DEVICE_ID = 0x00,
+ PF1550_PMIC_REG_OTP_FLAVOR = 0x01,
+ PF1550_PMIC_REG_SILICON_REV = 0x02,
+
+ PF1550_PMIC_REG_INT_CATEGORY = 0x06,
+ PF1550_PMIC_REG_SW_INT_STAT0 = 0x08,
+ PF1550_PMIC_REG_SW_INT_MASK0 = 0x09,
+ PF1550_PMIC_REG_SW_INT_SENSE0 = 0x0a,
+ PF1550_PMIC_REG_SW_INT_STAT1 = 0x0b,
+ PF1550_PMIC_REG_SW_INT_MASK1 = 0x0c,
+ PF1550_PMIC_REG_SW_INT_SENSE1 = 0x0d,
+ PF1550_PMIC_REG_SW_INT_STAT2 = 0x0e,
+ PF1550_PMIC_REG_SW_INT_MASK2 = 0x0f,
+ PF1550_PMIC_REG_SW_INT_SENSE2 = 0x10,
+ PF1550_PMIC_REG_LDO_INT_STAT0 = 0x18,
+ PF1550_PMIC_REG_LDO_INT_MASK0 = 0x19,
+ PF1550_PMIC_REG_LDO_INT_SENSE0 = 0x1a,
+ PF1550_PMIC_REG_TEMP_INT_STAT0 = 0x20,
+ PF1550_PMIC_REG_TEMP_INT_MASK0 = 0x21,
+ PF1550_PMIC_REG_TEMP_INT_SENSE0 = 0x22,
+ PF1550_PMIC_REG_ONKEY_INT_STAT0 = 0x24,
+ PF1550_PMIC_REG_ONKEY_INT_MASK0 = 0x25,
+ PF1550_PMIC_REG_ONKEY_INT_SENSE0 = 0x26,
+ PF1550_PMIC_REG_MISC_INT_STAT0 = 0x28,
+ PF1550_PMIC_REG_MISC_INT_MASK0 = 0x29,
+ PF1550_PMIC_REG_MISC_INT_SENSE0 = 0x2a,
+
+ PF1550_PMIC_REG_COINCELL_CONTROL = 0x30,
+
+ PF1550_PMIC_REG_SW1_VOLT = 0x32,
+ PF1550_PMIC_REG_SW1_STBY_VOLT = 0x33,
+ PF1550_PMIC_REG_SW1_SLP_VOLT = 0x34,
+ PF1550_PMIC_REG_SW1_CTRL = 0x35,
+ PF1550_PMIC_REG_SW1_CTRL1 = 0x36,
+ PF1550_PMIC_REG_SW2_VOLT = 0x38,
+ PF1550_PMIC_REG_SW2_STBY_VOLT = 0x39,
+ PF1550_PMIC_REG_SW2_SLP_VOLT = 0x3a,
+ PF1550_PMIC_REG_SW2_CTRL = 0x3b,
+ PF1550_PMIC_REG_SW2_CTRL1 = 0x3c,
+ PF1550_PMIC_REG_SW3_VOLT = 0x3e,
+ PF1550_PMIC_REG_SW3_STBY_VOLT = 0x3f,
+ PF1550_PMIC_REG_SW3_SLP_VOLT = 0x40,
+ PF1550_PMIC_REG_SW3_CTRL = 0x41,
+ PF1550_PMIC_REG_SW3_CTRL1 = 0x42,
+ PF1550_PMIC_REG_VSNVS_CTRL = 0x48,
+ PF1550_PMIC_REG_VREFDDR_CTRL = 0x4a,
+ PF1550_PMIC_REG_LDO1_VOLT = 0x4c,
+ PF1550_PMIC_REG_LDO1_CTRL = 0x4d,
+ PF1550_PMIC_REG_LDO2_VOLT = 0x4f,
+ PF1550_PMIC_REG_LDO2_CTRL = 0x50,
+ PF1550_PMIC_REG_LDO3_VOLT = 0x52,
+ PF1550_PMIC_REG_LDO3_CTRL = 0x53,
+ PF1550_PMIC_REG_PWRCTRL0 = 0x58,
+ PF1550_PMIC_REG_PWRCTRL1 = 0x59,
+ PF1550_PMIC_REG_PWRCTRL2 = 0x5a,
+ PF1550_PMIC_REG_PWRCTRL3 = 0x5b,
+ PF1550_PMIC_REG_SW1_PWRDN_SEQ = 0x5f,
+ PF1550_PMIC_REG_SW2_PWRDN_SEQ = 0x60,
+ PF1550_PMIC_REG_SW3_PWRDN_SEQ = 0x61,
+ PF1550_PMIC_REG_LDO1_PWRDN_SEQ = 0x62,
+ PF1550_PMIC_REG_LDO2_PWRDN_SEQ = 0x63,
+ PF1550_PMIC_REG_LDO3_PWRDN_SEQ = 0x64,
+ PF1550_PMIC_REG_VREFDDR_PWRDN_SEQ = 0x65,
+
+ PF1550_PMIC_REG_STATE_INFO = 0x67,
+ PF1550_PMIC_REG_I2C_ADDR = 0x68,
+ PF1550_PMIC_REG_IO_DRV0 = 0x69,
+ PF1550_PMIC_REG_IO_DRV1 = 0x6a,
+ PF1550_PMIC_REG_RC_16MHZ = 0x6b,
+ PF1550_PMIC_REG_KEY = 0x6f,
+
+ /* Charger part */
+ PF1550_CHARG_REG_CHG_INT = 0x80,
+ PF1550_CHARG_REG_CHG_INT_MASK = 0x82,
+ PF1550_CHARG_REG_CHG_INT_OK = 0x84,
+ PF1550_CHARG_REG_VBUS_SNS = 0x86,
+ PF1550_CHARG_REG_CHG_SNS = 0x87,
+ PF1550_CHARG_REG_BATT_SNS = 0x88,
+ PF1550_CHARG_REG_CHG_OPER = 0x89,
+ PF1550_CHARG_REG_CHG_TMR = 0x8a,
+ PF1550_CHARG_REG_CHG_EOC_CNFG = 0x8d,
+ PF1550_CHARG_REG_CHG_CURR_CNFG = 0x8e,
+ PF1550_CHARG_REG_BATT_REG = 0x8f,
+ PF1550_CHARG_REG_BATFET_CNFG = 0x91,
+ PF1550_CHARG_REG_THM_REG_CNFG = 0x92,
+ PF1550_CHARG_REG_VBUS_INLIM_CNFG = 0x94,
+ PF1550_CHARG_REG_VBUS_LIN_DPM = 0x95,
+ PF1550_CHARG_REG_USB_PHY_LDO_CNFG = 0x96,
+ PF1550_CHARG_REG_DBNC_DELAY_TIME = 0x98,
+ PF1550_CHARG_REG_CHG_INT_CNFG = 0x99,
+ PF1550_CHARG_REG_THM_ADJ_SETTING = 0x9a,
+ PF1550_CHARG_REG_VBUS2SYS_CNFG = 0x9b,
+ PF1550_CHARG_REG_LED_PWM = 0x9c,
+ PF1550_CHARG_REG_FAULT_BATFET_CNFG = 0x9d,
+ PF1550_CHARG_REG_LED_CNFG = 0x9e,
+ PF1550_CHARG_REG_CHGR_KEY2 = 0x9f,
+
+ PF1550_TEST_REG_FMRADDR = 0xc4,
+ PF1550_TEST_REG_FMRDATA = 0xc5,
+ PF1550_TEST_REG_KEY3 = 0xdf,
+
+ PF1550_PMIC_REG_END = 0xff,
+};
+
+/* One-Time Programmable(OTP) memory */
+enum pf1550_otp_reg {
+ PF1550_OTP_SW1_SW2 = 0x1e,
+ PF1550_OTP_SW2_SW3 = 0x1f,
+};
+
+#define PF1550_DEVICE_ID 0x7c
+
+/* Keys for reading OTP */
+#define PF1550_OTP_PMIC_KEY 0x15
+#define PF1550_OTP_CHGR_KEY 0x50
+#define PF1550_OTP_TEST_KEY 0xab
+
+/* Supported charger modes */
+#define PF1550_CHG_BAT_OFF 1
+#define PF1550_CHG_BAT_ON 2
+
+#define PF1550_CHG_PRECHARGE 0
+#define PF1550_CHG_CONSTANT_CURRENT 1
+#define PF1550_CHG_CONSTANT_VOL 2
+#define PF1550_CHG_EOC 3
+#define PF1550_CHG_DONE 4
+#define PF1550_CHG_TIMER_FAULT 6
+#define PF1550_CHG_SUSPEND 7
+#define PF1550_CHG_OFF_INV 8
+#define PF1550_CHG_BAT_OVER 9
+#define PF1550_CHG_OFF_TEMP 10
+#define PF1550_CHG_LINEAR_ONLY 12
+#define PF1550_CHG_SNS_MASK 0xf
+#define PF1550_CHG_INT_MASK 0x51
+
+#define PF1550_BAT_NO_VBUS 0
+#define PF1550_BAT_LOW_THAN_PRECHARG 1
+#define PF1550_BAT_CHARG_FAIL 2
+#define PF1550_BAT_HIGH_THAN_PRECHARG 4
+#define PF1550_BAT_OVER_VOL 5
+#define PF1550_BAT_NO_DETECT 6
+#define PF1550_BAT_SNS_MASK 0x7
+
+#define PF1550_VBUS_UVLO BIT(2)
+#define PF1550_VBUS_IN2SYS BIT(3)
+#define PF1550_VBUS_OVLO BIT(4)
+#define PF1550_VBUS_VALID BIT(5)
+
+#define PF1550_CHARG_REG_BATT_REG_CHGCV_MASK 0x3f
+#define PF1550_CHARG_REG_BATT_REG_VMINSYS_SHIFT 6
+#define PF1550_CHARG_REG_BATT_REG_VMINSYS_MASK GENMASK(7, 6)
+#define PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_SHIFT 2
+#define PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_MASK GENMASK(3, 2)
+
+#define PF1550_ONKEY_RST_EN BIT(7)
+
+/* DVS enable masks */
+#define OTP_SW1_DVS_ENB BIT(1)
+#define OTP_SW2_DVS_ENB BIT(3)
+
+/* Top level interrupt masks */
+#define IRQ_REGULATOR (BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(6))
+#define IRQ_ONKEY BIT(5)
+#define IRQ_CHG BIT(0)
+
+/* Regulator interrupt masks */
+#define PMIC_IRQ_SW1_LS BIT(0)
+#define PMIC_IRQ_SW2_LS BIT(1)
+#define PMIC_IRQ_SW3_LS BIT(2)
+#define PMIC_IRQ_SW1_HS BIT(0)
+#define PMIC_IRQ_SW2_HS BIT(1)
+#define PMIC_IRQ_SW3_HS BIT(2)
+#define PMIC_IRQ_LDO1_FAULT BIT(0)
+#define PMIC_IRQ_LDO2_FAULT BIT(1)
+#define PMIC_IRQ_LDO3_FAULT BIT(2)
+#define PMIC_IRQ_TEMP_110 BIT(0)
+#define PMIC_IRQ_TEMP_125 BIT(1)
+
+/* Onkey interrupt masks */
+#define ONKEY_IRQ_PUSHI BIT(0)
+#define ONKEY_IRQ_1SI BIT(1)
+#define ONKEY_IRQ_2SI BIT(2)
+#define ONKEY_IRQ_3SI BIT(3)
+#define ONKEY_IRQ_4SI BIT(4)
+#define ONKEY_IRQ_8SI BIT(5)
+
+/* Charger interrupt masks */
+#define CHARG_IRQ_BAT2SOCI BIT(1)
+#define CHARG_IRQ_BATI BIT(2)
+#define CHARG_IRQ_CHGI BIT(3)
+#define CHARG_IRQ_VBUSI BIT(5)
+#define CHARG_IRQ_DPMI BIT(6)
+#define CHARG_IRQ_THMI BIT(7)
+
+enum pf1550_irq {
+ PF1550_IRQ_CHG,
+ PF1550_IRQ_REGULATOR,
+ PF1550_IRQ_ONKEY,
+};
+
+enum pf1550_pmic_irq {
+ PF1550_PMIC_IRQ_SW1_LS,
+ PF1550_PMIC_IRQ_SW2_LS,
+ PF1550_PMIC_IRQ_SW3_LS,
+ PF1550_PMIC_IRQ_SW1_HS,
+ PF1550_PMIC_IRQ_SW2_HS,
+ PF1550_PMIC_IRQ_SW3_HS,
+ PF1550_PMIC_IRQ_LDO1_FAULT,
+ PF1550_PMIC_IRQ_LDO2_FAULT,
+ PF1550_PMIC_IRQ_LDO3_FAULT,
+ PF1550_PMIC_IRQ_TEMP_110,
+ PF1550_PMIC_IRQ_TEMP_125,
+};
+
+enum pf1550_onkey_irq {
+ PF1550_ONKEY_IRQ_PUSHI,
+ PF1550_ONKEY_IRQ_1SI,
+ PF1550_ONKEY_IRQ_2SI,
+ PF1550_ONKEY_IRQ_3SI,
+ PF1550_ONKEY_IRQ_4SI,
+ PF1550_ONKEY_IRQ_8SI,
+};
+
+enum pf1550_charg_irq {
+ PF1550_CHARG_IRQ_BAT2SOCI,
+ PF1550_CHARG_IRQ_BATI,
+ PF1550_CHARG_IRQ_CHGI,
+ PF1550_CHARG_IRQ_VBUSI,
+ PF1550_CHARG_IRQ_THMI,
+};
+
+enum pf1550_regulators {
+ PF1550_SW1,
+ PF1550_SW2,
+ PF1550_SW3,
+ PF1550_VREFDDR,
+ PF1550_LDO1,
+ PF1550_LDO2,
+ PF1550_LDO3,
+};
+
+struct pf1550_ddata {
+ struct regmap_irq_chip_data *irq_data_regulator;
+ struct regmap_irq_chip_data *irq_data_charger;
+ struct regmap_irq_chip_data *irq_data_onkey;
+ struct regmap_irq_chip_data *irq_data;
+ struct regmap *regmap;
+ struct device *dev;
+ bool dvs1_enable;
+ bool dvs2_enable;
+ int irq;
+};
+
+#endif /* __LINUX_MFD_PF1550_H */
--
2.50.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v10 3/6] regulator: pf1550: add support for regulator
2025-08-20 20:44 [PATCH v10 0/6] add support for pf1550 PMIC MFD-based drivers Samuel Kayode via B4 Relay
2025-08-20 20:44 ` [PATCH v10 1/6] dt-bindings: mfd: add pf1550 Samuel Kayode via B4 Relay
2025-08-20 20:44 ` [PATCH v10 2/6] mfd: pf1550: add core driver Samuel Kayode via B4 Relay
@ 2025-08-20 20:44 ` Samuel Kayode via B4 Relay
2025-08-20 20:44 ` [PATCH v10 4/6] input: pf1550: add onkey support Samuel Kayode via B4 Relay
` (2 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Samuel Kayode via B4 Relay @ 2025-08-20 20:44 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Liam Girdwood, Mark Brown, Dmitry Torokhov, Sebastian Reichel,
Frank Li
Cc: imx, devicetree, linux-kernel, linux-input, linux-pm, Abel Vesa,
Abel Vesa, Robin Gong, Robin Gong, Enric Balletbo i Serra,
Sean Nyekjaer, Christophe JAILLET, Samuel Kayode, Abel Vesa,
Frank Li
From: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
Add regulator support for the pf1550 PMIC.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
---
v10:
- Change dvsX_enb to dvsX_enable
v9:
- Requested by Sean:
- Add support for SW1 DVS enable/disable
- Add support for standby voltages
- Add map_voltage for all configurable regulators
- Add regulator enable/disable for all regulators
- Fix for DVS activation when meant to be disabled
v7:
- Use reverese christmas tree style
- Drop unecessary 0 in id table's driver data
v6:
- Use dvs_enb variable in pf1550_dev as suggested by Frank Li
v5:
- Address Mark's feedback:
- Add comments to clarify difference in interrupts
- Issue warn event for _LS(low side) interrupt
- Validate maximum ramp_delay
v4:
- Address Mark's feedback:
- Use C++ comments for SPDX license
- Add portions copyright to reflect my update
- Validate ramp_delay
- Report overcurrent and temperature events
- Use platform_get_irq
v3:
- Drop duplicate include
- Drop unnecessary includes
- Accept lower case regulator names from devicetree
- Use virqs mapped in core MFD driver
v2:
- Add driver for regulator
---
drivers/regulator/Kconfig | 9 +
drivers/regulator/Makefile | 1 +
drivers/regulator/pf1550-regulator.c | 429 +++++++++++++++++++++++++++++++++++
3 files changed, 439 insertions(+)
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 6d8988387da4599633ca9bde2698b9711e34a245..de455887f9aeeada5546e44b8dc9d7ed041618a6 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1049,6 +1049,15 @@ config REGULATOR_PV88090
Say y here to support the voltage regulators and convertors
on PV88090
+config REGULATOR_PF1550
+ tristate "NXP PF1550 regulator"
+ depends on MFD_PF1550
+ help
+ Say y here to select this option to enable the regulators on
+ the PF1550 PMICs.
+ This driver controls the PF1550 regulators via I2C bus.
+ The regulators include three bucks and three ldos.
+
config REGULATOR_PWM
tristate "PWM voltage regulator"
depends on PWM
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index c0bc7a0f4e67098c50ac3cf887ae95f46b2eac44..891174b511fc0653bac662c71659498122e8441f 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -125,6 +125,7 @@ obj-$(CONFIG_REGULATOR_QCOM_USB_VBUS) += qcom_usb_vbus-regulator.o
obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
obj-$(CONFIG_REGULATOR_PCA9450) += pca9450-regulator.o
obj-$(CONFIG_REGULATOR_PF9453) += pf9453-regulator.o
+obj-$(CONFIG_REGULATOR_PF1550) += pf1550-regulator.o
obj-$(CONFIG_REGULATOR_PF8X00) += pf8x00-regulator.o
obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
obj-$(CONFIG_REGULATOR_PV88060) += pv88060-regulator.o
diff --git a/drivers/regulator/pf1550-regulator.c b/drivers/regulator/pf1550-regulator.c
new file mode 100644
index 0000000000000000000000000000000000000000..90492609773886343151c2ba40d2d4bf84c37c5e
--- /dev/null
+++ b/drivers/regulator/pf1550-regulator.c
@@ -0,0 +1,429 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// regulator driver for the PF1550
+//
+// Copyright (C) 2016 Freescale Semiconductor, Inc.
+// Robin Gong <yibin.gong@freescale.com>
+//
+// Portions Copyright (c) 2025 Savoir-faire Linux Inc.
+// Samuel Kayode <samuel.kayode@savoirfairelinux.com>
+//
+
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/pf1550.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+#define PF1550_REGULATOR_IRQ_NR 11
+#define PF1550_MAX_REGULATOR 7
+
+struct pf1550_desc {
+ struct regulator_desc desc;
+ unsigned char stby_reg;
+ unsigned char stby_mask;
+ unsigned char stby_enable_reg;
+ unsigned char stby_enable_mask;
+};
+
+struct pf1550_regulator_info {
+ struct device *dev;
+ const struct pf1550_ddata *pf1550;
+ struct pf1550_desc regulator_descs[PF1550_MAX_REGULATOR];
+ struct regulator_dev *rdevs[PF1550_MAX_REGULATOR];
+};
+
+static const int pf1550_sw12_volts[] = {
+ 1100000, 1200000, 1350000, 1500000, 1800000, 2500000, 3000000, 3300000,
+};
+
+static const int pf1550_ldo13_volts[] = {
+ 750000, 800000, 850000, 900000, 950000, 1000000, 1050000, 1100000,
+ 1150000, 1200000, 1250000, 1300000, 1350000, 1400000, 1450000, 1500000,
+ 1800000, 1900000, 2000000, 2100000, 2200000, 2300000, 2400000, 2500000,
+ 2600000, 2700000, 2800000, 2900000, 3000000, 3100000, 3200000, 3300000,
+};
+
+static int pf1550_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+ int id = rdev_get_id(rdev);
+ unsigned int ramp_bits = 0;
+ int ret;
+
+ if (id > PF1550_VREFDDR)
+ return -EACCES;
+
+ if (ramp_delay < 0 || ramp_delay > 6250)
+ return -EINVAL;
+
+ ramp_delay = 6250 / ramp_delay;
+ ramp_bits = ramp_delay >> 1;
+
+ ret = regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg + 4, 0x10,
+ ramp_bits << 4);
+ if (ret < 0)
+ dev_err(&rdev->dev, "ramp failed, err %d\n", ret);
+
+ return ret;
+}
+
+static int pf1550_set_suspend_enable(struct regulator_dev *rdev)
+{
+ const struct pf1550_desc *desc = container_of(rdev->desc,
+ struct pf1550_desc,
+ desc);
+ unsigned int val = desc->stby_enable_mask;
+
+ return regmap_update_bits(rdev->regmap, desc->stby_enable_reg,
+ desc->stby_enable_mask, val);
+}
+
+static int pf1550_set_suspend_disable(struct regulator_dev *rdev)
+{
+ const struct pf1550_desc *desc = container_of(rdev->desc,
+ struct pf1550_desc,
+ desc);
+
+ return regmap_update_bits(rdev->regmap, desc->stby_enable_reg,
+ desc->stby_enable_mask, 0);
+}
+
+static int pf1550_buck_set_table_suspend_voltage(struct regulator_dev *rdev,
+ int uV)
+{
+ const struct pf1550_desc *desc = container_of(rdev->desc,
+ struct pf1550_desc,
+ desc);
+ int ret;
+
+ ret = regulator_map_voltage_ascend(rdev, uV, uV);
+ if (ret < 0) {
+ dev_err(rdev_get_dev(rdev), "failed to map %i uV\n", uV);
+ return ret;
+ }
+
+ return regmap_update_bits(rdev->regmap, desc->stby_reg,
+ desc->stby_mask, ret);
+}
+
+static int pf1550_buck_set_linear_suspend_voltage(struct regulator_dev *rdev,
+ int uV)
+{
+ const struct pf1550_desc *desc = container_of(rdev->desc,
+ struct pf1550_desc,
+ desc);
+ int ret;
+
+ ret = regulator_map_voltage_linear(rdev, uV, uV);
+ if (ret < 0) {
+ dev_err(rdev_get_dev(rdev), "failed to map %i uV\n", uV);
+ return ret;
+ }
+
+ return regmap_update_bits(rdev->regmap, desc->stby_reg,
+ desc->stby_mask, ret);
+}
+
+static const struct regulator_ops pf1550_sw1_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .set_suspend_enable = pf1550_set_suspend_enable,
+ .set_suspend_disable = pf1550_set_suspend_disable,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_table,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_suspend_voltage = pf1550_buck_set_table_suspend_voltage,
+ .map_voltage = regulator_map_voltage_ascend,
+ .set_ramp_delay = pf1550_set_ramp_delay,
+};
+
+static const struct regulator_ops pf1550_sw2_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .set_suspend_enable = pf1550_set_suspend_enable,
+ .set_suspend_disable = pf1550_set_suspend_disable,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_suspend_voltage = pf1550_buck_set_linear_suspend_voltage,
+ .map_voltage = regulator_map_voltage_linear,
+ .set_ramp_delay = pf1550_set_ramp_delay,
+};
+
+static const struct regulator_ops pf1550_ldo1_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .set_suspend_enable = pf1550_set_suspend_enable,
+ .set_suspend_disable = pf1550_set_suspend_disable,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_table,
+ .map_voltage = regulator_map_voltage_ascend,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static const struct regulator_ops pf1550_ldo2_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .set_suspend_enable = pf1550_set_suspend_enable,
+ .set_suspend_disable = pf1550_set_suspend_disable,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .map_voltage = regulator_map_voltage_linear,
+};
+
+static const struct regulator_ops pf1550_fixed_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .set_suspend_enable = pf1550_set_suspend_enable,
+ .set_suspend_disable = pf1550_set_suspend_disable,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+};
+
+#define PF_VREF(_chip, match, _name, voltage) { \
+ .desc = { \
+ .name = #_name, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .n_voltages = 1, \
+ .ops = &pf1550_fixed_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = _chip ## _ ## _name, \
+ .owner = THIS_MODULE, \
+ .min_uV = (voltage), \
+ .enable_reg = _chip ## _PMIC_REG_ ## _name ## _CTRL, \
+ .enable_mask = 0x1, \
+ }, \
+ .stby_enable_reg = _chip ## _PMIC_REG_ ## _name ## _CTRL, \
+ .stby_enable_mask = 0x2, \
+}
+
+#define PF_SW(_chip, match, _name, min, max, mask, step) { \
+ .desc = { \
+ .name = #_name, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .n_voltages = ((max) - (min)) / (step) + 1, \
+ .ops = &pf1550_sw2_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = _chip ## _ ## _name, \
+ .owner = THIS_MODULE, \
+ .min_uV = (min), \
+ .uV_step = (step), \
+ .linear_min_sel = 0, \
+ .vsel_reg = _chip ## _PMIC_REG_ ## _name ## _VOLT, \
+ .vsel_mask = (mask), \
+ .enable_reg = _chip ## _PMIC_REG_ ## _name ## _CTRL, \
+ .enable_mask = 0x1, \
+ }, \
+ .stby_reg = _chip ## _PMIC_REG_ ## _name ## _STBY_VOLT, \
+ .stby_mask = (mask), \
+ .stby_enable_reg = _chip ## _PMIC_REG_ ## _name ## _CTRL, \
+ .stby_enable_mask = 0x2, \
+}
+
+#define PF_LDO1(_chip, match, _name, mask, voltages) { \
+ .desc = { \
+ .name = #_name, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .n_voltages = ARRAY_SIZE(voltages), \
+ .ops = &pf1550_ldo1_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = _chip ## _ ## _name, \
+ .owner = THIS_MODULE, \
+ .volt_table = voltages, \
+ .vsel_reg = _chip ## _PMIC_REG_ ## _name ## _VOLT, \
+ .vsel_mask = (mask), \
+ .enable_reg = _chip ## _PMIC_REG_ ## _name ## _CTRL, \
+ .enable_mask = 0x1, \
+ }, \
+ .stby_enable_reg = _chip ## _PMIC_REG_ ## _name ## _CTRL, \
+ .stby_enable_mask = 0x2, \
+}
+
+#define PF_LDO2(_chip, match, _name, mask, min, max, step) { \
+ .desc = { \
+ .name = #_name, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .n_voltages = ((max) - (min)) / (step) + 1, \
+ .ops = &pf1550_ldo2_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = _chip ## _ ## _name, \
+ .owner = THIS_MODULE, \
+ .min_uV = (min), \
+ .uV_step = (step), \
+ .linear_min_sel = 0, \
+ .vsel_reg = _chip ## _PMIC_REG_ ## _name ## _VOLT, \
+ .vsel_mask = (mask), \
+ .enable_reg = _chip ## _PMIC_REG_ ## _name ## _CTRL, \
+ .enable_mask = 0x1, \
+ }, \
+ .stby_enable_reg = _chip ## _PMIC_REG_ ## _name ## _CTRL, \
+ .stby_enable_mask = 0x2, \
+}
+
+static struct pf1550_desc pf1550_regulators[] = {
+ PF_SW(PF1550, "sw1", SW1, 600000, 1387500, 0x3f, 12500),
+ PF_SW(PF1550, "sw2", SW2, 600000, 1387500, 0x3f, 12500),
+ PF_SW(PF1550, "sw3", SW3, 1800000, 3300000, 0xf, 100000),
+ PF_VREF(PF1550, "vrefddr", VREFDDR, 1200000),
+ PF_LDO1(PF1550, "ldo1", LDO1, 0x1f, pf1550_ldo13_volts),
+ PF_LDO2(PF1550, "ldo2", LDO2, 0xf, 1800000, 3300000, 100000),
+ PF_LDO1(PF1550, "ldo3", LDO3, 0x1f, pf1550_ldo13_volts),
+};
+
+static irqreturn_t pf1550_regulator_irq_handler(int irq, void *data)
+{
+ struct pf1550_regulator_info *info = data;
+ struct device *dev = info->dev;
+ struct platform_device *pdev = to_platform_device(dev);
+ int i, irq_type = -1;
+ unsigned int event;
+
+ for (i = 0; i < PF1550_REGULATOR_IRQ_NR; i++)
+ if (irq == platform_get_irq(pdev, i))
+ irq_type = i;
+
+ switch (irq_type) {
+ /* The _LS interrupts indicate over-current event. The _HS interrupts
+ * which are more accurate and can detect catastrophic faults, issue
+ * an error event. The current limit FAULT interrupt is similar to the
+ * _HS'
+ */
+ case PF1550_PMIC_IRQ_SW1_LS:
+ case PF1550_PMIC_IRQ_SW2_LS:
+ case PF1550_PMIC_IRQ_SW3_LS:
+ event = REGULATOR_EVENT_OVER_CURRENT_WARN;
+ for (i = 0; i < PF1550_MAX_REGULATOR; i++)
+ if (!strcmp(rdev_get_name(info->rdevs[i]), "SW3"))
+ regulator_notifier_call_chain(info->rdevs[i],
+ event, NULL);
+ break;
+ case PF1550_PMIC_IRQ_SW1_HS:
+ case PF1550_PMIC_IRQ_SW2_HS:
+ case PF1550_PMIC_IRQ_SW3_HS:
+ event = REGULATOR_EVENT_OVER_CURRENT;
+ for (i = 0; i < PF1550_MAX_REGULATOR; i++)
+ if (!strcmp(rdev_get_name(info->rdevs[i]), "SW3"))
+ regulator_notifier_call_chain(info->rdevs[i],
+ event, NULL);
+ break;
+ case PF1550_PMIC_IRQ_LDO1_FAULT:
+ case PF1550_PMIC_IRQ_LDO2_FAULT:
+ case PF1550_PMIC_IRQ_LDO3_FAULT:
+ event = REGULATOR_EVENT_OVER_CURRENT;
+ for (i = 0; i < PF1550_MAX_REGULATOR; i++)
+ if (!strcmp(rdev_get_name(info->rdevs[i]), "LDO3"))
+ regulator_notifier_call_chain(info->rdevs[i],
+ event, NULL);
+ break;
+ case PF1550_PMIC_IRQ_TEMP_110:
+ case PF1550_PMIC_IRQ_TEMP_125:
+ event = REGULATOR_EVENT_OVER_TEMP;
+ for (i = 0; i < PF1550_MAX_REGULATOR; i++)
+ regulator_notifier_call_chain(info->rdevs[i],
+ event, NULL);
+ break;
+ default:
+ dev_err(dev, "regulator interrupt: irq %d occurred\n",
+ irq_type);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int pf1550_regulator_probe(struct platform_device *pdev)
+{
+ const struct pf1550_ddata *pf1550 = dev_get_drvdata(pdev->dev.parent);
+ struct regulator_config config = { };
+ struct pf1550_regulator_info *info;
+ int i, irq = -1, ret = 0;
+
+ info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ config.regmap = dev_get_regmap(pf1550->dev, NULL);
+ if (!config.regmap)
+ return dev_err_probe(&pdev->dev, -ENODEV,
+ "failed to get parent regmap\n");
+
+ config.dev = pf1550->dev;
+ config.regmap = pf1550->regmap;
+ info->dev = &pdev->dev;
+ info->pf1550 = pf1550;
+
+ memcpy(info->regulator_descs, pf1550_regulators,
+ sizeof(info->regulator_descs));
+
+ for (i = 0; i < ARRAY_SIZE(pf1550_regulators); i++) {
+ struct regulator_desc *desc;
+
+ desc = &info->regulator_descs[i].desc;
+
+ if ((desc->id == PF1550_SW2 && !pf1550->dvs2_enable) ||
+ (desc->id == PF1550_SW1 && !pf1550->dvs1_enable)) {
+ /* OTP_SW2_DVS_ENB == 1? or OTP_SW1_DVS_ENB == 1? */
+ desc->volt_table = pf1550_sw12_volts;
+ desc->n_voltages = ARRAY_SIZE(pf1550_sw12_volts);
+ desc->ops = &pf1550_sw1_ops;
+ }
+
+ info->rdevs[i] = devm_regulator_register(&pdev->dev, desc,
+ &config);
+ if (IS_ERR(info->rdevs[i]))
+ return dev_err_probe(&pdev->dev,
+ PTR_ERR(info->rdevs[i]),
+ "failed to initialize regulator-%d\n",
+ i);
+ }
+
+ platform_set_drvdata(pdev, info);
+
+ for (i = 0; i < PF1550_REGULATOR_IRQ_NR; i++) {
+ irq = platform_get_irq(pdev, i);
+ if (irq < 0)
+ return irq;
+
+ ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+ pf1550_regulator_irq_handler,
+ IRQF_NO_SUSPEND,
+ "pf1550-regulator", info);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret,
+ "failed: irq request (IRQ: %d)\n",
+ i);
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id pf1550_regulator_id[] = {
+ { "pf1550-regulator", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, pf1550_regulator_id);
+
+static struct platform_driver pf1550_regulator_driver = {
+ .driver = {
+ .name = "pf1550-regulator",
+ },
+ .probe = pf1550_regulator_probe,
+ .id_table = pf1550_regulator_id,
+};
+module_platform_driver(pf1550_regulator_driver);
+
+MODULE_DESCRIPTION("NXP PF1550 regulator driver");
+MODULE_AUTHOR("Robin Gong <yibin.gong@freescale.com>");
+MODULE_LICENSE("GPL");
--
2.50.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v10 4/6] input: pf1550: add onkey support
2025-08-20 20:44 [PATCH v10 0/6] add support for pf1550 PMIC MFD-based drivers Samuel Kayode via B4 Relay
` (2 preceding siblings ...)
2025-08-20 20:44 ` [PATCH v10 3/6] regulator: pf1550: add support for regulator Samuel Kayode via B4 Relay
@ 2025-08-20 20:44 ` Samuel Kayode via B4 Relay
2025-08-20 20:44 ` [PATCH v10 5/6] power: supply: pf1550: add battery charger support Samuel Kayode via B4 Relay
2025-08-20 20:44 ` [PATCH v10 6/6] MAINTAINERS: add an entry for pf1550 mfd driver Samuel Kayode via B4 Relay
5 siblings, 0 replies; 8+ messages in thread
From: Samuel Kayode via B4 Relay @ 2025-08-20 20:44 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Liam Girdwood, Mark Brown, Dmitry Torokhov, Sebastian Reichel,
Frank Li
Cc: imx, devicetree, linux-kernel, linux-input, linux-pm, Abel Vesa,
Abel Vesa, Robin Gong, Robin Gong, Enric Balletbo i Serra,
Sean Nyekjaer, Christophe JAILLET, Samuel Kayode, Abel Vesa,
Frank Li
From: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
Add support for the onkey of the pf1550 PMIC.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
---
v10:
- Use regmap_clear_bits instead of regmap_write
v9:
- Requested by Sean:
- Add support for disabling power down of system by onkey
v8:
- Pick up `Acked-by` tag from Dmitry
- Use C++ for SPDX license header comment and C type for rest of license
comment
v7:
- Use reverese christmas tree style
- Drop unecessary 0 in id table's driver data
v4:
- Address Dmitry's feedback
- Drop irq variable in onkey_drv_data
- Drop keycode variable in onkey_drv_data
- Define wakeup as type bool
- Use platform_get_irq
- Use type const for struct pf1550_dev in onkey_drv_data
- Replace (error < 0) with (error) in if statement when applicable
- No need to define driver_data in table id
- Define driver.pm with pm_sleep_ptr
v3:
- Address Dmitry's feedback
- Drop compatible string
- Remove dependency on OF
- Use generic device properties
- Drop unnecessary includes
- Drop unnecessary initializations in probe
- Always use the KEY_POWER property for onkey->keycode
- Do mapping of irqs in MFD driver
- Define onkey->input before interrupts are active
- Drop unnecessary input_free_device since devm
- Manage onkey irqs instead of the main interrupt line.
- Fix integer overflow when unmasking onkey irqs in onkey_resume.
v2:
- Add driver for onkey
---
drivers/input/misc/Kconfig | 11 +++
drivers/input/misc/Makefile | 1 +
drivers/input/misc/pf1550-onkey.c | 197 ++++++++++++++++++++++++++++++++++++++
3 files changed, 209 insertions(+)
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
index f5496ca0c0d2bfcb7968503ccd1844ff43bbc1c0..47b3c43ff0550f14d61990997976366436411adc 100644
--- a/drivers/input/misc/Kconfig
+++ b/drivers/input/misc/Kconfig
@@ -179,6 +179,17 @@ config INPUT_PCSPKR
To compile this driver as a module, choose M here: the
module will be called pcspkr.
+config INPUT_PF1550_ONKEY
+ tristate "NXP PF1550 Onkey support"
+ depends on MFD_PF1550
+ help
+ Say Y here if you want support for PF1550 PMIC. Onkey can trigger
+ release and 1s(push hold), 2s, 3s, 4s, 8s interrupt for long press
+ detect.
+
+ To compile this driver as a module, choose M here. The module will be
+ called pf1550-onkey.
+
config INPUT_PM8941_PWRKEY
tristate "Qualcomm PM8941 power key support"
depends on MFD_SPMI_PMIC
diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile
index 6d91804d0a6f761a094e6c380f878f74c3054d63..c652337de464c1eeaf1515d0bc84d10de0cb3a74 100644
--- a/drivers/input/misc/Makefile
+++ b/drivers/input/misc/Makefile
@@ -62,6 +62,7 @@ obj-$(CONFIG_INPUT_PCAP) += pcap_keys.o
obj-$(CONFIG_INPUT_PCF50633_PMU) += pcf50633-input.o
obj-$(CONFIG_INPUT_PCF8574) += pcf8574_keypad.o
obj-$(CONFIG_INPUT_PCSPKR) += pcspkr.o
+obj-$(CONFIG_INPUT_PF1550_ONKEY) += pf1550-onkey.o
obj-$(CONFIG_INPUT_PM8941_PWRKEY) += pm8941-pwrkey.o
obj-$(CONFIG_INPUT_PM8XXX_VIBRATOR) += pm8xxx-vibrator.o
obj-$(CONFIG_INPUT_PMIC8XXX_PWRKEY) += pmic8xxx-pwrkey.o
diff --git a/drivers/input/misc/pf1550-onkey.c b/drivers/input/misc/pf1550-onkey.c
new file mode 100644
index 0000000000000000000000000000000000000000..9be6377151cb3be824ab34ff37f983196b909324
--- /dev/null
+++ b/drivers/input/misc/pf1550-onkey.c
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the PF1550 ONKEY
+ * Copyright (C) 2016 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * Portions Copyright (c) 2025 Savoir-faire Linux Inc.
+ * Samuel Kayode <samuel.kayode@savoirfairelinux.com>
+ */
+
+#include <linux/err.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mfd/pf1550.h>
+#include <linux/platform_device.h>
+
+#define PF1550_ONKEY_IRQ_NR 6
+
+struct onkey_drv_data {
+ struct device *dev;
+ const struct pf1550_ddata *pf1550;
+ bool wakeup;
+ struct input_dev *input;
+};
+
+static irqreturn_t pf1550_onkey_irq_handler(int irq, void *data)
+{
+ struct onkey_drv_data *onkey = data;
+ struct platform_device *pdev = to_platform_device(onkey->dev);
+ int i, state, irq_type = -1;
+
+ for (i = 0; i < PF1550_ONKEY_IRQ_NR; i++)
+ if (irq == platform_get_irq(pdev, i))
+ irq_type = i;
+
+ switch (irq_type) {
+ case PF1550_ONKEY_IRQ_PUSHI:
+ state = 0;
+ break;
+ case PF1550_ONKEY_IRQ_1SI:
+ case PF1550_ONKEY_IRQ_2SI:
+ case PF1550_ONKEY_IRQ_3SI:
+ case PF1550_ONKEY_IRQ_4SI:
+ case PF1550_ONKEY_IRQ_8SI:
+ state = 1;
+ break;
+ default:
+ dev_err(onkey->dev, "onkey interrupt: irq %d occurred\n",
+ irq_type);
+ return IRQ_HANDLED;
+ }
+
+ input_event(onkey->input, EV_KEY, KEY_POWER, state);
+ input_sync(onkey->input);
+
+ return IRQ_HANDLED;
+}
+
+static int pf1550_onkey_probe(struct platform_device *pdev)
+{
+ struct onkey_drv_data *onkey;
+ struct input_dev *input;
+ bool key_power = false;
+ int i, irq, error;
+
+ onkey = devm_kzalloc(&pdev->dev, sizeof(*onkey), GFP_KERNEL);
+ if (!onkey)
+ return -ENOMEM;
+
+ onkey->dev = &pdev->dev;
+
+ onkey->pf1550 = dev_get_drvdata(pdev->dev.parent);
+ if (!onkey->pf1550->regmap)
+ return dev_err_probe(&pdev->dev, -ENODEV,
+ "failed to get regmap\n");
+
+ onkey->wakeup = device_property_read_bool(pdev->dev.parent,
+ "wakeup-source");
+
+ if (device_property_read_bool(pdev->dev.parent,
+ "nxp,disable-key-power")) {
+ error = regmap_clear_bits(onkey->pf1550->regmap,
+ PF1550_PMIC_REG_PWRCTRL1,
+ PF1550_ONKEY_RST_EN);
+ if (error)
+ return dev_err_probe(&pdev->dev, error,
+ "failed: disable turn system off");
+ } else {
+ key_power = true;
+ }
+
+ input = devm_input_allocate_device(&pdev->dev);
+ if (!input)
+ return dev_err_probe(&pdev->dev, -ENOMEM,
+ "failed to allocate the input device\n");
+
+ input->name = pdev->name;
+ input->phys = "pf1550-onkey/input0";
+ input->id.bustype = BUS_HOST;
+
+ if (key_power)
+ input_set_capability(input, EV_KEY, KEY_POWER);
+
+ onkey->input = input;
+ platform_set_drvdata(pdev, onkey);
+
+ for (i = 0; i < PF1550_ONKEY_IRQ_NR; i++) {
+ irq = platform_get_irq(pdev, i);
+ if (irq < 0)
+ return irq;
+
+ error = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+ pf1550_onkey_irq_handler,
+ IRQF_NO_SUSPEND,
+ "pf1550-onkey", onkey);
+ if (error)
+ return dev_err_probe(&pdev->dev, error,
+ "failed: irq request (IRQ: %d)\n",
+ i);
+ }
+
+ error = input_register_device(input);
+ if (error)
+ return dev_err_probe(&pdev->dev, error,
+ "failed to register input device\n");
+
+ device_init_wakeup(&pdev->dev, onkey->wakeup);
+
+ return 0;
+}
+
+static int pf1550_onkey_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct onkey_drv_data *onkey = platform_get_drvdata(pdev);
+ int i, irq;
+
+ if (!device_may_wakeup(&pdev->dev))
+ regmap_write(onkey->pf1550->regmap,
+ PF1550_PMIC_REG_ONKEY_INT_MASK0,
+ ONKEY_IRQ_PUSHI | ONKEY_IRQ_1SI | ONKEY_IRQ_2SI |
+ ONKEY_IRQ_3SI | ONKEY_IRQ_4SI | ONKEY_IRQ_8SI);
+ else
+ for (i = 0; i < PF1550_ONKEY_IRQ_NR; i++) {
+ irq = platform_get_irq(pdev, i);
+ if (irq > 0)
+ enable_irq_wake(irq);
+ }
+
+ return 0;
+}
+
+static int pf1550_onkey_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct onkey_drv_data *onkey = platform_get_drvdata(pdev);
+ int i, irq;
+
+ if (!device_may_wakeup(&pdev->dev))
+ regmap_write(onkey->pf1550->regmap,
+ PF1550_PMIC_REG_ONKEY_INT_MASK0,
+ ~((u8)(ONKEY_IRQ_PUSHI | ONKEY_IRQ_1SI |
+ ONKEY_IRQ_2SI | ONKEY_IRQ_3SI | ONKEY_IRQ_4SI |
+ ONKEY_IRQ_8SI)));
+ else
+ for (i = 0; i < PF1550_ONKEY_IRQ_NR; i++) {
+ irq = platform_get_irq(pdev, i);
+ if (irq > 0)
+ disable_irq_wake(irq);
+ }
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(pf1550_onkey_pm_ops, pf1550_onkey_suspend,
+ pf1550_onkey_resume);
+
+static const struct platform_device_id pf1550_onkey_id[] = {
+ { "pf1550-onkey", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, pf1550_onkey_id);
+
+static struct platform_driver pf1550_onkey_driver = {
+ .driver = {
+ .name = "pf1550-onkey",
+ .pm = pm_sleep_ptr(&pf1550_onkey_pm_ops),
+ },
+ .probe = pf1550_onkey_probe,
+ .id_table = pf1550_onkey_id,
+};
+module_platform_driver(pf1550_onkey_driver);
+
+MODULE_AUTHOR("Freescale Semiconductor");
+MODULE_DESCRIPTION("PF1550 onkey Driver");
+MODULE_LICENSE("GPL");
--
2.50.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v10 5/6] power: supply: pf1550: add battery charger support
2025-08-20 20:44 [PATCH v10 0/6] add support for pf1550 PMIC MFD-based drivers Samuel Kayode via B4 Relay
` (3 preceding siblings ...)
2025-08-20 20:44 ` [PATCH v10 4/6] input: pf1550: add onkey support Samuel Kayode via B4 Relay
@ 2025-08-20 20:44 ` Samuel Kayode via B4 Relay
2025-09-02 13:41 ` Lee Jones
2025-08-20 20:44 ` [PATCH v10 6/6] MAINTAINERS: add an entry for pf1550 mfd driver Samuel Kayode via B4 Relay
5 siblings, 1 reply; 8+ messages in thread
From: Samuel Kayode via B4 Relay @ 2025-08-20 20:44 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Liam Girdwood, Mark Brown, Dmitry Torokhov, Sebastian Reichel,
Frank Li
Cc: imx, devicetree, linux-kernel, linux-input, linux-pm, Abel Vesa,
Abel Vesa, Robin Gong, Robin Gong, Enric Balletbo i Serra,
Sean Nyekjaer, Christophe JAILLET, Samuel Kayode, Abel Vesa,
Frank Li
From: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
Add support for the battery charger for pf1550 PMIC.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
---
v9:
- Fix thermal regulation temperature ranges
- Fix default thermal regulation temperature
- Drop unused `data` variable in reg_init
- Select charger operation mode based on application - suggested by Sean
v8:
- Drop PF1550_CHARGER_NAME
- Drop unnecessary POWER_SUPPLY_STATUS_CHARGING s
- Replace POWER_SUPPLY_HEALTH_DEAD with POWER_SUPPLY_HEALTH_NO_BATTERY
- Drop check for charger in delayed_work s
- Use dev_warn when battery is over-voltage
- Define two power supplies: charger and battery
- Use devm_delayed_work_autocancel to automate cleanup and fix race
condition
v7:
- Use reverse christmas tree order
- Drop unecessary 0 in id table's driver data field
- Store virqs to avoid reinvoking platform_get_irq in the interrupt
service routine
- Drop manufacturer and model global variables
v6:
- Drop lock entirely
- Reverse christmas tree order for variables defined in probe as
suggested by Frank
- return pf1550_reg_init
v5:
- Drop lock for battery and charger delayed_work
- More conservative locking in vbus delayed_work
- Apply lock when setting power supply type during register initialization
v4:
- Finish handling of some interrupts in threaded irq handler
- Use platform_get_irq
v3:
- Use struct power_supply_get_battery_info to get constant charge
voltage if specified
- Use virqs mapped in MFD driver
v2:
- Address feedback from Enric Balletbo Serra
---
drivers/power/supply/Kconfig | 11 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/pf1550-charger.c | 636 ++++++++++++++++++++++++++++++++++
3 files changed, 648 insertions(+)
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 79ddb006e2dad6bf96b71ed570a37c006b5f9433..6d0c872edac1f45da314632e671af1aeda4c87b8 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -471,6 +471,17 @@ config CHARGER_88PM860X
help
Say Y here to enable charger for Marvell 88PM860x chip.
+config CHARGER_PF1550
+ tristate "NXP PF1550 battery charger driver"
+ depends on MFD_PF1550
+ help
+ Say Y to enable support for the NXP PF1550 battery charger.
+ The device is a single cell Li-Ion/Li-Polymer battery charger for
+ portable application.
+
+ This driver can also be built as a module. If so, the module will be
+ called pf1550-charger.
+
config BATTERY_RX51
tristate "Nokia RX-51 (N900) battery driver"
depends on TWL4030_MADC
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index 4f5f8e3507f80da02812f0d08c2d81ddff0a272f..7f68380099c59dab71b73120150612a23e16a745 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -64,6 +64,7 @@ obj-$(CONFIG_CHARGER_RT9467) += rt9467-charger.o
obj-$(CONFIG_CHARGER_RT9471) += rt9471.o
obj-$(CONFIG_BATTERY_TWL4030_MADC) += twl4030_madc_battery.o
obj-$(CONFIG_CHARGER_88PM860X) += 88pm860x_charger.o
+obj-$(CONFIG_CHARGER_PF1550) += pf1550-charger.o
obj-$(CONFIG_BATTERY_RX51) += rx51_battery.o
obj-$(CONFIG_AB8500_BM) += ab8500_bmdata.o ab8500_charger.o ab8500_fg.o ab8500_btemp.o ab8500_chargalg.o
obj-$(CONFIG_CHARGER_CPCAP) += cpcap-charger.o
diff --git a/drivers/power/supply/pf1550-charger.c b/drivers/power/supply/pf1550-charger.c
new file mode 100644
index 0000000000000000000000000000000000000000..2c43cc086a18239b46c73553d73a85a60ba7c41e
--- /dev/null
+++ b/drivers/power/supply/pf1550-charger.c
@@ -0,0 +1,636 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * charger driver for the PF1550
+ *
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Robin Gong <yibin.gong@freescale.com>
+ *
+ * Portions Copyright (c) 2025 Savoir-faire Linux Inc.
+ * Samuel Kayode <samuel.kayode@savoirfairelinux.com>
+ */
+
+#include <linux/devm-helpers.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/pf1550.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+
+#define PF1550_DEFAULT_CONSTANT_VOLT 4200000
+#define PF1550_DEFAULT_MIN_SYSTEM_VOLT 3500000
+#define PF1550_DEFAULT_THERMAL_TEMP 95
+#define PF1550_CHARGER_IRQ_NR 5
+
+struct pf1550_charger {
+ struct device *dev;
+ const struct pf1550_ddata *pf1550;
+ struct power_supply *charger;
+ struct power_supply *battery;
+ struct delayed_work vbus_sense_work;
+ struct delayed_work chg_sense_work;
+ struct delayed_work bat_sense_work;
+ int virqs[PF1550_CHARGER_IRQ_NR];
+
+ u32 constant_volt;
+ u32 min_system_volt;
+ u32 thermal_regulation_temp;
+};
+
+static int pf1550_get_charger_state(struct regmap *regmap, int *val)
+{
+ unsigned int data;
+ int ret;
+
+ ret = regmap_read(regmap, PF1550_CHARG_REG_CHG_SNS, &data);
+ if (ret < 0)
+ return ret;
+
+ data &= PF1550_CHG_SNS_MASK;
+
+ switch (data) {
+ case PF1550_CHG_PRECHARGE:
+ case PF1550_CHG_CONSTANT_CURRENT:
+ case PF1550_CHG_CONSTANT_VOL:
+ case PF1550_CHG_EOC:
+ *val = POWER_SUPPLY_STATUS_CHARGING;
+ break;
+ case PF1550_CHG_DONE:
+ *val = POWER_SUPPLY_STATUS_FULL;
+ break;
+ case PF1550_CHG_TIMER_FAULT:
+ case PF1550_CHG_SUSPEND:
+ *val = POWER_SUPPLY_STATUS_NOT_CHARGING;
+ break;
+ case PF1550_CHG_OFF_INV:
+ case PF1550_CHG_OFF_TEMP:
+ case PF1550_CHG_LINEAR_ONLY:
+ *val = POWER_SUPPLY_STATUS_DISCHARGING;
+ break;
+ default:
+ *val = POWER_SUPPLY_STATUS_UNKNOWN;
+ }
+
+ return 0;
+}
+
+static int pf1550_get_charge_type(struct regmap *regmap, int *val)
+{
+ unsigned int data;
+ int ret;
+
+ ret = regmap_read(regmap, PF1550_CHARG_REG_CHG_SNS, &data);
+ if (ret < 0)
+ return ret;
+
+ data &= PF1550_CHG_SNS_MASK;
+
+ switch (data) {
+ case PF1550_CHG_SNS_MASK:
+ *val = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
+ break;
+ case PF1550_CHG_CONSTANT_CURRENT:
+ case PF1550_CHG_CONSTANT_VOL:
+ case PF1550_CHG_EOC:
+ *val = POWER_SUPPLY_CHARGE_TYPE_FAST;
+ break;
+ case PF1550_CHG_DONE:
+ case PF1550_CHG_TIMER_FAULT:
+ case PF1550_CHG_SUSPEND:
+ case PF1550_CHG_OFF_INV:
+ case PF1550_CHG_BAT_OVER:
+ case PF1550_CHG_OFF_TEMP:
+ case PF1550_CHG_LINEAR_ONLY:
+ *val = POWER_SUPPLY_CHARGE_TYPE_NONE;
+ break;
+ default:
+ *val = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN;
+ }
+
+ return 0;
+}
+
+/*
+ * Supported health statuses:
+ * - POWER_SUPPLY_HEALTH_DEAD
+ * - POWER_SUPPLY_HEALTH_GOOD
+ * - POWER_SUPPLY_HEALTH_OVERVOLTAGE
+ * - POWER_SUPPLY_HEALTH_UNKNOWN
+ */
+static int pf1550_get_battery_health(struct regmap *regmap, int *val)
+{
+ unsigned int data;
+ int ret;
+
+ ret = regmap_read(regmap, PF1550_CHARG_REG_BATT_SNS, &data);
+ if (ret < 0)
+ return ret;
+
+ data &= PF1550_BAT_SNS_MASK;
+
+ switch (data) {
+ case PF1550_BAT_NO_DETECT:
+ *val = POWER_SUPPLY_HEALTH_NO_BATTERY;
+ break;
+ case PF1550_BAT_NO_VBUS:
+ case PF1550_BAT_LOW_THAN_PRECHARG:
+ case PF1550_BAT_CHARG_FAIL:
+ case PF1550_BAT_HIGH_THAN_PRECHARG:
+ *val = POWER_SUPPLY_HEALTH_GOOD;
+ break;
+ case PF1550_BAT_OVER_VOL:
+ *val = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+ break;
+ default:
+ *val = POWER_SUPPLY_HEALTH_UNKNOWN;
+ break;
+ }
+
+ return 0;
+}
+
+static int pf1550_get_present(struct regmap *regmap, int *val)
+{
+ unsigned int data;
+ int ret;
+
+ ret = regmap_read(regmap, PF1550_CHARG_REG_BATT_SNS, &data);
+ if (ret < 0)
+ return ret;
+
+ data &= PF1550_BAT_SNS_MASK;
+ *val = (data == PF1550_BAT_NO_DETECT) ? 0 : 1;
+
+ return 0;
+}
+
+static int pf1550_get_online(struct regmap *regmap, int *val)
+{
+ unsigned int data;
+ int ret;
+
+ ret = regmap_read(regmap, PF1550_CHARG_REG_VBUS_SNS, &data);
+ if (ret < 0)
+ return ret;
+
+ *val = (data & PF1550_VBUS_VALID) ? 1 : 0;
+
+ return 0;
+}
+
+static void pf1550_chg_bat_work(struct work_struct *work)
+{
+ struct pf1550_charger *chg = container_of(to_delayed_work(work),
+ struct pf1550_charger,
+ bat_sense_work);
+ unsigned int data;
+
+ if (regmap_read(chg->pf1550->regmap, PF1550_CHARG_REG_BATT_SNS, &data)) {
+ dev_err(chg->dev, "Read BATT_SNS error.\n");
+ return;
+ }
+
+ switch (data & PF1550_BAT_SNS_MASK) {
+ case PF1550_BAT_NO_VBUS:
+ dev_dbg(chg->dev, "No valid VBUS input.\n");
+ break;
+ case PF1550_BAT_LOW_THAN_PRECHARG:
+ dev_dbg(chg->dev, "VBAT < VPRECHG.LB.\n");
+ break;
+ case PF1550_BAT_CHARG_FAIL:
+ dev_dbg(chg->dev, "Battery charging failed.\n");
+ break;
+ case PF1550_BAT_HIGH_THAN_PRECHARG:
+ dev_dbg(chg->dev, "VBAT > VPRECHG.LB.\n");
+ break;
+ case PF1550_BAT_OVER_VOL:
+ dev_dbg(chg->dev, "VBAT > VBATOV.\n");
+ break;
+ case PF1550_BAT_NO_DETECT:
+ dev_dbg(chg->dev, "Battery not detected.\n");
+ break;
+ default:
+ dev_err(chg->dev, "Unknown value read:%x\n",
+ data & PF1550_CHG_SNS_MASK);
+ }
+}
+
+static void pf1550_chg_chg_work(struct work_struct *work)
+{
+ struct pf1550_charger *chg = container_of(to_delayed_work(work),
+ struct pf1550_charger,
+ chg_sense_work);
+ unsigned int data;
+
+ if (regmap_read(chg->pf1550->regmap, PF1550_CHARG_REG_CHG_SNS, &data)) {
+ dev_err(chg->dev, "Read CHG_SNS error.\n");
+ return;
+ }
+
+ switch (data & PF1550_CHG_SNS_MASK) {
+ case PF1550_CHG_PRECHARGE:
+ dev_dbg(chg->dev, "In pre-charger mode.\n");
+ break;
+ case PF1550_CHG_CONSTANT_CURRENT:
+ dev_dbg(chg->dev, "In fast-charge constant current mode.\n");
+ break;
+ case PF1550_CHG_CONSTANT_VOL:
+ dev_dbg(chg->dev, "In fast-charge constant voltage mode.\n");
+ break;
+ case PF1550_CHG_EOC:
+ dev_dbg(chg->dev, "In EOC mode.\n");
+ break;
+ case PF1550_CHG_DONE:
+ dev_dbg(chg->dev, "In DONE mode.\n");
+ break;
+ case PF1550_CHG_TIMER_FAULT:
+ dev_info(chg->dev, "In timer fault mode.\n");
+ break;
+ case PF1550_CHG_SUSPEND:
+ dev_info(chg->dev, "In thermistor suspend mode.\n");
+ break;
+ case PF1550_CHG_OFF_INV:
+ dev_info(chg->dev, "Input invalid, charger off.\n");
+ break;
+ case PF1550_CHG_BAT_OVER:
+ dev_warn(chg->dev, "Battery over-voltage.\n");
+ break;
+ case PF1550_CHG_OFF_TEMP:
+ dev_info(chg->dev, "Temp high, charger off.\n");
+ break;
+ case PF1550_CHG_LINEAR_ONLY:
+ dev_dbg(chg->dev, "In Linear mode, not charging.\n");
+ break;
+ default:
+ dev_err(chg->dev, "Unknown value read:%x\n",
+ data & PF1550_CHG_SNS_MASK);
+ }
+}
+
+static void pf1550_chg_vbus_work(struct work_struct *work)
+{
+ struct pf1550_charger *chg = container_of(to_delayed_work(work),
+ struct pf1550_charger,
+ vbus_sense_work);
+ unsigned int data;
+
+ if (regmap_read(chg->pf1550->regmap, PF1550_CHARG_REG_VBUS_SNS, &data)) {
+ dev_err(chg->dev, "Read VBUS_SNS error.\n");
+ return;
+ }
+
+ if (data & PF1550_VBUS_UVLO) {
+ dev_dbg(chg->dev, "VBUS detached.\n");
+ power_supply_changed(chg->battery);
+ }
+ if (data & PF1550_VBUS_IN2SYS)
+ dev_dbg(chg->dev, "VBUS_IN2SYS_SNS.\n");
+ if (data & PF1550_VBUS_OVLO)
+ dev_dbg(chg->dev, "VBUS_OVLO_SNS.\n");
+ if (data & PF1550_VBUS_VALID) {
+ dev_dbg(chg->dev, "VBUS attached.\n");
+ power_supply_changed(chg->charger);
+ }
+}
+
+static irqreturn_t pf1550_charger_irq_handler(int irq, void *data)
+{
+ struct pf1550_charger *chg = data;
+ struct device *dev = chg->dev;
+ int i, irq_type = -1;
+
+ for (i = 0; i < PF1550_CHARGER_IRQ_NR; i++)
+ if (irq == chg->virqs[i])
+ irq_type = i;
+
+ switch (irq_type) {
+ case PF1550_CHARG_IRQ_BAT2SOCI:
+ dev_info(dev, "BAT to SYS Overcurrent interrupt.\n");
+ break;
+ case PF1550_CHARG_IRQ_BATI:
+ schedule_delayed_work(&chg->bat_sense_work,
+ msecs_to_jiffies(10));
+ break;
+ case PF1550_CHARG_IRQ_CHGI:
+ schedule_delayed_work(&chg->chg_sense_work,
+ msecs_to_jiffies(10));
+ break;
+ case PF1550_CHARG_IRQ_VBUSI:
+ schedule_delayed_work(&chg->vbus_sense_work,
+ msecs_to_jiffies(10));
+ break;
+ case PF1550_CHARG_IRQ_THMI:
+ dev_info(dev, "Thermal interrupt.\n");
+ break;
+ default:
+ dev_err(dev, "unknown interrupt occurred.\n");
+ }
+
+ return IRQ_HANDLED;
+}
+
+static enum power_supply_property pf1550_charger_props[] = {
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_CHARGE_TYPE,
+ POWER_SUPPLY_PROP_HEALTH,
+ POWER_SUPPLY_PROP_PRESENT,
+ POWER_SUPPLY_PROP_ONLINE,
+ POWER_SUPPLY_PROP_MODEL_NAME,
+ POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static int pf1550_charger_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct pf1550_charger *chg = power_supply_get_drvdata(psy);
+ struct regmap *regmap = chg->pf1550->regmap;
+ int ret = 0;
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_STATUS:
+ ret = pf1550_get_charger_state(regmap, &val->intval);
+ break;
+ case POWER_SUPPLY_PROP_CHARGE_TYPE:
+ ret = pf1550_get_charge_type(regmap, &val->intval);
+ break;
+ case POWER_SUPPLY_PROP_HEALTH:
+ ret = pf1550_get_battery_health(regmap, &val->intval);
+ break;
+ case POWER_SUPPLY_PROP_PRESENT:
+ ret = pf1550_get_present(regmap, &val->intval);
+ break;
+ case POWER_SUPPLY_PROP_ONLINE:
+ ret = pf1550_get_online(regmap, &val->intval);
+ break;
+ case POWER_SUPPLY_PROP_MODEL_NAME:
+ val->strval = "PF1550";
+ break;
+ case POWER_SUPPLY_PROP_MANUFACTURER:
+ val->strval = "NXP";
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return ret;
+}
+
+static const struct power_supply_desc pf1550_charger_desc = {
+ .name = "pf1550-charger",
+ .type = POWER_SUPPLY_TYPE_MAINS,
+ .properties = pf1550_charger_props,
+ .num_properties = ARRAY_SIZE(pf1550_charger_props),
+ .get_property = pf1550_charger_get_property,
+};
+
+static const struct power_supply_desc pf1550_battery_desc = {
+ .name = "pf1550-battery",
+ .type = POWER_SUPPLY_TYPE_BATTERY,
+ .properties = pf1550_charger_props,
+ .num_properties = ARRAY_SIZE(pf1550_charger_props),
+ .get_property = pf1550_charger_get_property,
+};
+
+static int pf1550_set_constant_volt(struct pf1550_charger *chg,
+ unsigned int uvolt)
+{
+ unsigned int data;
+
+ if (uvolt >= 3500000 && uvolt <= 4440000)
+ data = 8 + (uvolt - 3500000) / 20000;
+ else
+ return dev_err_probe(chg->dev, -EINVAL,
+ "Wrong value for constant voltage\n");
+
+ dev_dbg(chg->dev, "Charging constant voltage: %u (0x%x)\n", uvolt,
+ data);
+
+ return regmap_update_bits(chg->pf1550->regmap,
+ PF1550_CHARG_REG_BATT_REG,
+ PF1550_CHARG_REG_BATT_REG_CHGCV_MASK, data);
+}
+
+static int pf1550_set_min_system_volt(struct pf1550_charger *chg,
+ unsigned int uvolt)
+{
+ unsigned int data;
+
+ switch (uvolt) {
+ case 3500000:
+ data = 0x0;
+ break;
+ case 3700000:
+ data = 0x1;
+ break;
+ case 4300000:
+ data = 0x2;
+ break;
+ default:
+ return dev_err_probe(chg->dev, -EINVAL,
+ "Wrong value for minimum system voltage\n");
+ }
+
+ data <<= PF1550_CHARG_REG_BATT_REG_VMINSYS_SHIFT;
+
+ dev_dbg(chg->dev, "Minimum system regulation voltage: %u (0x%x)\n",
+ uvolt, data);
+
+ return regmap_update_bits(chg->pf1550->regmap,
+ PF1550_CHARG_REG_BATT_REG,
+ PF1550_CHARG_REG_BATT_REG_VMINSYS_MASK, data);
+}
+
+static int pf1550_set_thermal_regulation_temp(struct pf1550_charger *chg,
+ unsigned int cells)
+{
+ unsigned int data;
+
+ switch (cells) {
+ case 80:
+ data = 0x0;
+ break;
+ case 95:
+ data = 0x1;
+ break;
+ case 110:
+ data = 0x2;
+ break;
+ case 125:
+ data = 0x3;
+ break;
+ default:
+ return dev_err_probe(chg->dev, -EINVAL,
+ "Wrong value for thermal temperature\n");
+ }
+
+ data <<= PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_SHIFT;
+
+ dev_dbg(chg->dev, "Thermal regulation loop temperature: %u (0x%x)\n",
+ cells, data);
+
+ return regmap_update_bits(chg->pf1550->regmap,
+ PF1550_CHARG_REG_THM_REG_CNFG,
+ PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_MASK,
+ data);
+}
+
+/*
+ * Sets charger registers to proper and safe default values.
+ */
+static int pf1550_reg_init(struct pf1550_charger *chg)
+{
+ struct power_supply_battery_info *info;
+ struct device *dev = chg->dev;
+ int ret;
+
+ /* Unmask charger interrupt, mask DPMI and reserved bit */
+ ret = regmap_write(chg->pf1550->regmap, PF1550_CHARG_REG_CHG_INT_MASK,
+ PF1550_CHG_INT_MASK);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Error unmask charger interrupt\n");
+
+ ret = pf1550_set_constant_volt(chg, chg->constant_volt);
+ if (ret)
+ return ret;
+
+ ret = pf1550_set_min_system_volt(chg, chg->min_system_volt);
+ if (ret)
+ return ret;
+
+ ret = pf1550_set_thermal_regulation_temp(chg,
+ chg->thermal_regulation_temp);
+ if (ret)
+ return ret;
+
+ /*
+ * The PF1550 charger has 3 modes of operation. By default, the charger
+ * is in mode 1; it remains off. Appropriate for applications not using
+ * a battery. The other supported mode is mode 2, the charger is turned
+ * on to charge a battery when present.
+ */
+ if (power_supply_get_battery_info(chg->charger, &info)) {
+ ret = regmap_write(chg->pf1550->regmap,
+ PF1550_CHARG_REG_CHG_OPER,
+ PF1550_CHG_BAT_ON);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Error turn on charger\n");
+ }
+
+ return 0;
+}
+
+static void pf1550_dt_parse_dev_info(struct pf1550_charger *chg)
+{
+ struct power_supply_battery_info *info;
+ struct device *dev = chg->dev;
+
+ if (device_property_read_u32(dev->parent, "nxp,min-system-microvolt",
+ &chg->min_system_volt))
+ chg->min_system_volt = PF1550_DEFAULT_MIN_SYSTEM_VOLT;
+
+ if (device_property_read_u32(dev->parent,
+ "nxp,thermal-regulation-celsius",
+ &chg->thermal_regulation_temp))
+ chg->thermal_regulation_temp = PF1550_DEFAULT_THERMAL_TEMP;
+
+ if (power_supply_get_battery_info(chg->charger, &info))
+ chg->constant_volt = PF1550_DEFAULT_CONSTANT_VOLT;
+ else
+ chg->constant_volt = info->constant_charge_voltage_max_uv;
+}
+
+static int pf1550_charger_probe(struct platform_device *pdev)
+{
+ const struct pf1550_ddata *pf1550 = dev_get_drvdata(pdev->dev.parent);
+ struct power_supply_config psy_cfg = {};
+ struct pf1550_charger *chg;
+ int i, irq, ret;
+
+ chg = devm_kzalloc(&pdev->dev, sizeof(*chg), GFP_KERNEL);
+ if (!chg)
+ return -ENOMEM;
+
+ chg->dev = &pdev->dev;
+ chg->pf1550 = pf1550;
+
+ if (!chg->pf1550->regmap)
+ return dev_err_probe(&pdev->dev, -ENODEV,
+ "failed to get regmap\n");
+
+ platform_set_drvdata(pdev, chg);
+
+ ret = devm_delayed_work_autocancel(chg->dev, &chg->vbus_sense_work,
+ pf1550_chg_vbus_work);
+ if (ret)
+ return dev_err_probe(chg->dev, ret,
+ "failed to add vbus sense work\n");
+
+ ret = devm_delayed_work_autocancel(chg->dev, &chg->chg_sense_work,
+ pf1550_chg_chg_work);
+ if (ret)
+ return dev_err_probe(chg->dev, ret,
+ "failed to add charger sense work\n");
+
+ ret = devm_delayed_work_autocancel(chg->dev, &chg->bat_sense_work,
+ pf1550_chg_bat_work);
+ if (ret)
+ return dev_err_probe(chg->dev, ret,
+ "failed to add battery sense work\n");
+
+ for (i = 0; i < PF1550_CHARGER_IRQ_NR; i++) {
+ irq = platform_get_irq(pdev, i);
+ if (irq < 0)
+ return irq;
+
+ chg->virqs[i] = irq;
+
+ ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+ pf1550_charger_irq_handler,
+ IRQF_NO_SUSPEND,
+ "pf1550-charger", chg);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret,
+ "failed irq request\n");
+ }
+
+ psy_cfg.drv_data = chg;
+
+ chg->charger = devm_power_supply_register(&pdev->dev,
+ &pf1550_charger_desc,
+ &psy_cfg);
+ if (IS_ERR(chg->charger))
+ return dev_err_probe(&pdev->dev, PTR_ERR(chg->charger),
+ "failed: power supply register\n");
+
+ chg->battery = devm_power_supply_register(&pdev->dev,
+ &pf1550_battery_desc,
+ &psy_cfg);
+ if (IS_ERR(chg->battery))
+ return dev_err_probe(&pdev->dev, PTR_ERR(chg->battery),
+ "failed: power supply register\n");
+
+ pf1550_dt_parse_dev_info(chg);
+
+ return pf1550_reg_init(chg);
+}
+
+static const struct platform_device_id pf1550_charger_id[] = {
+ { "pf1550-charger", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, pf1550_charger_id);
+
+static struct platform_driver pf1550_charger_driver = {
+ .driver = {
+ .name = "pf1550-charger",
+ },
+ .probe = pf1550_charger_probe,
+ .id_table = pf1550_charger_id,
+};
+module_platform_driver(pf1550_charger_driver);
+
+MODULE_AUTHOR("Robin Gong <yibin.gong@freescale.com>");
+MODULE_DESCRIPTION("PF1550 charger driver");
+MODULE_LICENSE("GPL");
--
2.50.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH v10 5/6] power: supply: pf1550: add battery charger support
2025-08-20 20:44 ` [PATCH v10 5/6] power: supply: pf1550: add battery charger support Samuel Kayode via B4 Relay
@ 2025-09-02 13:41 ` Lee Jones
0 siblings, 0 replies; 8+ messages in thread
From: Lee Jones @ 2025-09-02 13:41 UTC (permalink / raw)
To: samuel.kayode
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Liam Girdwood,
Mark Brown, Dmitry Torokhov, Sebastian Reichel, Frank Li, imx,
devicetree, linux-kernel, linux-input, linux-pm, Abel Vesa,
Abel Vesa, Robin Gong, Robin Gong, Enric Balletbo i Serra,
Sean Nyekjaer, Christophe JAILLET
Power:
> From: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
>
> Add support for the battery charger for pf1550 PMIC.
>
> Reviewed-by: Frank Li <Frank.Li@nxp.com>
> Tested-by: Sean Nyekjaer <sean@geanix.com>
> Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
> ---
> v9:
> - Fix thermal regulation temperature ranges
> - Fix default thermal regulation temperature
> - Drop unused `data` variable in reg_init
> - Select charger operation mode based on application - suggested by Sean
> v8:
> - Drop PF1550_CHARGER_NAME
> - Drop unnecessary POWER_SUPPLY_STATUS_CHARGING s
> - Replace POWER_SUPPLY_HEALTH_DEAD with POWER_SUPPLY_HEALTH_NO_BATTERY
> - Drop check for charger in delayed_work s
> - Use dev_warn when battery is over-voltage
> - Define two power supplies: charger and battery
> - Use devm_delayed_work_autocancel to automate cleanup and fix race
> condition
> v7:
> - Use reverse christmas tree order
> - Drop unecessary 0 in id table's driver data field
> - Store virqs to avoid reinvoking platform_get_irq in the interrupt
> service routine
> - Drop manufacturer and model global variables
> v6:
> - Drop lock entirely
> - Reverse christmas tree order for variables defined in probe as
> suggested by Frank
> - return pf1550_reg_init
> v5:
> - Drop lock for battery and charger delayed_work
> - More conservative locking in vbus delayed_work
> - Apply lock when setting power supply type during register initialization
> v4:
> - Finish handling of some interrupts in threaded irq handler
> - Use platform_get_irq
> v3:
> - Use struct power_supply_get_battery_info to get constant charge
> voltage if specified
> - Use virqs mapped in MFD driver
> v2:
> - Address feedback from Enric Balletbo Serra
> ---
> drivers/power/supply/Kconfig | 11 +
> drivers/power/supply/Makefile | 1 +
> drivers/power/supply/pf1550-charger.c | 636 ++++++++++++++++++++++++++++++++++
> 3 files changed, 648 insertions(+)
Once Sebastian takes this, I'll merge the set.
--
Lee Jones [李琼斯]
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v10 6/6] MAINTAINERS: add an entry for pf1550 mfd driver
2025-08-20 20:44 [PATCH v10 0/6] add support for pf1550 PMIC MFD-based drivers Samuel Kayode via B4 Relay
` (4 preceding siblings ...)
2025-08-20 20:44 ` [PATCH v10 5/6] power: supply: pf1550: add battery charger support Samuel Kayode via B4 Relay
@ 2025-08-20 20:44 ` Samuel Kayode via B4 Relay
5 siblings, 0 replies; 8+ messages in thread
From: Samuel Kayode via B4 Relay @ 2025-08-20 20:44 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Liam Girdwood, Mark Brown, Dmitry Torokhov, Sebastian Reichel,
Frank Li
Cc: imx, devicetree, linux-kernel, linux-input, linux-pm, Abel Vesa,
Abel Vesa, Robin Gong, Robin Gong, Enric Balletbo i Serra,
Sean Nyekjaer, Christophe JAILLET, Samuel Kayode, Abel Vesa,
Frank Li, Krzysztof Kozlowski
From: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
Add MAINTAINERS entry for pf1550 PMIC.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
---
v9:
- Pick up Frank's `Reviewed-by` tag
v6:
- Add imx mailing list
---
MAINTAINERS | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 60bba48f5479a025f9da3eaf9dbacb67a194df07..ffc834aace4272e663f9717bcffd67100eb546c7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17996,6 +17996,17 @@ F: Documentation/devicetree/bindings/clock/imx*
F: drivers/clk/imx/
F: include/dt-bindings/clock/imx*
+NXP PF1550 PMIC MFD DRIVER
+M: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
+L: imx@lists.linux.dev
+S: Maintained
+F: Documentation/devicetree/bindings/mfd/nxp,pf1550.yaml
+F: drivers/input/misc/pf1550-onkey.c
+F: drivers/mfd/pf1550.c
+F: drivers/power/supply/pf1550-charger.c
+F: drivers/regulator/pf1550-regulator.c
+F: include/linux/mfd/pfd1550.h
+
NXP PF8100/PF8121A/PF8200 PMIC REGULATOR DEVICE DRIVER
M: Jagan Teki <jagan@amarulasolutions.com>
S: Maintained
--
2.50.1
^ permalink raw reply related [flat|nested] 8+ messages in thread