* [PATCH v3 01/11] Documentation: Correction in HID output_report callback description.
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 02/11] HID: Add BUS_SPI support and define HID_SPI_DEVICE macro Jingyuan Liang
` (9 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang,
Jarrett Schultz, Dmitry Antipov
From: Jarrett Schultz <jaschultz@microsoft.com>
Originally output_report callback was described as must-be asynchronous,
but that is not the case in some implementations, namely i2c-hid.
Correct the documentation to say that it may be asynchronous.
Signed-off-by: Dmitry Antipov <dmanti@microsoft.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
Documentation/hid/hid-transport.rst | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/Documentation/hid/hid-transport.rst b/Documentation/hid/hid-transport.rst
index 6f1692da296c..2008cf432af1 100644
--- a/Documentation/hid/hid-transport.rst
+++ b/Documentation/hid/hid-transport.rst
@@ -327,8 +327,8 @@ The available HID callbacks are:
Send raw output report via intr channel. Used by some HID device drivers
which require high throughput for outgoing requests on the intr channel. This
- must not cause SET_REPORT calls! This must be implemented as asynchronous
- output report on the intr channel!
+ must not cause SET_REPORT calls! This call might be asynchronous, so the
+ caller should not expect an immediate response!
::
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 02/11] HID: Add BUS_SPI support and define HID_SPI_DEVICE macro
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 01/11] Documentation: Correction in HID output_report callback description Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 03/11] HID: spi-hid: add transport driver skeleton for HID over SPI bus Jingyuan Liang
` (8 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang,
Jarrett Schultz, Dmitry Antipov
From: Jarrett Schultz <jaschultz@microsoft.com>
If connecting a hid_device with bus field indicating BUS_SPI print out
"SPI" in the debug print.
Macro sets the bus field to BUS_SPI and uses arguments to set vendor
product fields.
Signed-off-by: Dmitry Antipov <dmanti@microsoft.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
drivers/hid/hid-core.c | 3 +++
include/linux/hid.h | 2 ++
2 files changed, 5 insertions(+)
diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
index a5b3a8ca2fcb..813c9c743ccd 100644
--- a/drivers/hid/hid-core.c
+++ b/drivers/hid/hid-core.c
@@ -2316,6 +2316,9 @@ int hid_connect(struct hid_device *hdev, unsigned int connect_mask)
case BUS_I2C:
bus = "I2C";
break;
+ case BUS_SPI:
+ bus = "SPI";
+ break;
case BUS_SDW:
bus = "SOUNDWIRE";
break;
diff --git a/include/linux/hid.h b/include/linux/hid.h
index dce862cafbbd..957f322a0ebd 100644
--- a/include/linux/hid.h
+++ b/include/linux/hid.h
@@ -786,6 +786,8 @@ struct hid_descriptor {
.bus = BUS_BLUETOOTH, .vendor = (ven), .product = (prod)
#define HID_I2C_DEVICE(ven, prod) \
.bus = BUS_I2C, .vendor = (ven), .product = (prod)
+#define HID_SPI_DEVICE(ven, prod) \
+ .bus = BUS_SPI, .vendor = (ven), .product = (prod)
#define HID_REPORT_ID(rep) \
.report_type = (rep)
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 03/11] HID: spi-hid: add transport driver skeleton for HID over SPI bus
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 01/11] Documentation: Correction in HID output_report callback description Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 02/11] HID: Add BUS_SPI support and define HID_SPI_DEVICE macro Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 04/11] HID: spi-hid: add spi-hid driver HID layer Jingyuan Liang
` (7 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang,
Angela Czubak, Dmitry Antipov
From: Angela Czubak <acz@semihalf.com>
Create spi-hid folder and add Kconfig and Makefile for spi-hid driver.
Add basic device structure, definitions, and probe/remove functions.
Signed-off-by: Dmitry Antipov <dmanti@microsoft.com>
Signed-off-by: Angela Czubak <acz@semihalf.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
drivers/hid/Kconfig | 2 +
drivers/hid/Makefile | 2 +
drivers/hid/spi-hid/Kconfig | 15 +++
drivers/hid/spi-hid/Makefile | 9 ++
drivers/hid/spi-hid/spi-hid-core.c | 213 +++++++++++++++++++++++++++++++++++++
5 files changed, 241 insertions(+)
diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
index 920a64b66b25..c6ae23bfb75d 100644
--- a/drivers/hid/Kconfig
+++ b/drivers/hid/Kconfig
@@ -1434,6 +1434,8 @@ source "drivers/hid/bpf/Kconfig"
source "drivers/hid/i2c-hid/Kconfig"
+source "drivers/hid/spi-hid/Kconfig"
+
source "drivers/hid/intel-ish-hid/Kconfig"
source "drivers/hid/amd-sfh-hid/Kconfig"
diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile
index 361a7daedeb8..6b43e789b39a 100644
--- a/drivers/hid/Makefile
+++ b/drivers/hid/Makefile
@@ -169,6 +169,8 @@ obj-$(CONFIG_USB_KBD) += usbhid/
obj-$(CONFIG_I2C_HID_CORE) += i2c-hid/
+obj-$(CONFIG_SPI_HID_CORE) += spi-hid/
+
obj-$(CONFIG_INTEL_ISH_HID) += intel-ish-hid/
obj-$(CONFIG_AMD_SFH_HID) += amd-sfh-hid/
diff --git a/drivers/hid/spi-hid/Kconfig b/drivers/hid/spi-hid/Kconfig
new file mode 100644
index 000000000000..836fdefe8345
--- /dev/null
+++ b/drivers/hid/spi-hid/Kconfig
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Copyright (c) 2021 Microsoft Corporation
+#
+
+menuconfig SPI_HID
+ tristate "SPI HID support"
+ default y
+ depends on SPI
+
+if SPI_HID
+
+config SPI_HID_CORE
+ tristate
+endif
diff --git a/drivers/hid/spi-hid/Makefile b/drivers/hid/spi-hid/Makefile
new file mode 100644
index 000000000000..92e24cddbfc2
--- /dev/null
+++ b/drivers/hid/spi-hid/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the SPI HID input drivers
+#
+# Copyright (c) 2021 Microsoft Corporation
+#
+
+obj-$(CONFIG_SPI_HID_CORE) += spi-hid.o
+spi-hid-objs = spi-hid-core.o
diff --git a/drivers/hid/spi-hid/spi-hid-core.c b/drivers/hid/spi-hid/spi-hid-core.c
new file mode 100644
index 000000000000..d7b4d4adad95
--- /dev/null
+++ b/drivers/hid/spi-hid/spi-hid-core.c
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * HID over SPI protocol implementation
+ *
+ * Copyright (c) 2021 Microsoft Corporation
+ * Copyright (c) 2026 Google LLC
+ *
+ * This code is partly based on "HID over I2C protocol implementation:
+ *
+ * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@gmail.com>
+ * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France
+ * Copyright (c) 2012 Red Hat, Inc
+ *
+ * which in turn is partly based on "USB HID support for Linux":
+ *
+ * Copyright (c) 1999 Andreas Gal
+ * Copyright (c) 2000-2005 Vojtech Pavlik <vojtech@suse.cz>
+ * Copyright (c) 2005 Michael Haboustak <mike-@cinci.rr.com> for Concept2, Inc
+ * Copyright (c) 2007-2008 Oliver Neukum
+ * Copyright (c) 2006-2010 Jiri Kosina
+ */
+
+#include <linux/device.h>
+#include <linux/hid.h>
+#include <linux/hid-over-spi.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+
+/* struct spi_hid_conf - Conf provided to the core */
+struct spi_hid_conf {
+ u32 input_report_header_address;
+ u32 input_report_body_address;
+ u32 output_report_address;
+ u8 read_opcode;
+ u8 write_opcode;
+};
+
+/**
+ * struct spihid_ops - Ops provided to the core
+ * @power_up: do sequencing to power up the device
+ * @power_down: do sequencing to power down the device
+ * @assert_reset: do sequencing to assert the reset line
+ * @deassert_reset: do sequencing to deassert the reset line
+ * @sleep_minimal_reset_delay: minimal sleep delay during reset
+ */
+struct spihid_ops {
+ int (*power_up)(struct spihid_ops *ops);
+ int (*power_down)(struct spihid_ops *ops);
+ int (*assert_reset)(struct spihid_ops *ops);
+ int (*deassert_reset)(struct spihid_ops *ops);
+ void (*sleep_minimal_reset_delay)(struct spihid_ops *ops);
+};
+
+/* Driver context */
+struct spi_hid {
+ struct spi_device *spi; /* spi device. */
+ struct hid_device *hid; /* pointer to corresponding HID dev. */
+
+ struct spihid_ops *ops;
+ struct spi_hid_conf *conf;
+
+ enum hidspi_power_state power_state;
+
+ u32 regulator_error_count;
+ int regulator_last_error;
+ u32 bus_error_count;
+ int bus_last_error;
+ u32 dir_count; /* device initiated reset count. */
+};
+
+static const char *spi_hid_power_mode_string(enum hidspi_power_state power_state)
+{
+ switch (power_state) {
+ case HIDSPI_ON:
+ return "d0";
+ case HIDSPI_SLEEP:
+ return "d2";
+ case HIDSPI_OFF:
+ return "d3";
+ default:
+ return "unknown";
+ }
+}
+
+static irqreturn_t spi_hid_dev_irq(int irq, void *_shid)
+{
+ return IRQ_HANDLED;
+}
+
+static ssize_t bus_error_count_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct spi_hid *shid = dev_get_drvdata(dev);
+
+ return sysfs_emit(buf, "%d (%d)\n",
+ shid->bus_error_count, shid->bus_last_error);
+}
+static DEVICE_ATTR_RO(bus_error_count);
+
+static ssize_t regulator_error_count_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct spi_hid *shid = dev_get_drvdata(dev);
+
+ return sysfs_emit(buf, "%d (%d)\n",
+ shid->regulator_error_count,
+ shid->regulator_last_error);
+}
+static DEVICE_ATTR_RO(regulator_error_count);
+
+static ssize_t device_initiated_reset_count_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct spi_hid *shid = dev_get_drvdata(dev);
+
+ return sysfs_emit(buf, "%d\n", shid->dir_count);
+}
+static DEVICE_ATTR_RO(device_initiated_reset_count);
+
+static struct attribute *spi_hid_attrs[] = {
+ &dev_attr_bus_error_count.attr,
+ &dev_attr_regulator_error_count.attr,
+ &dev_attr_device_initiated_reset_count.attr,
+ NULL /* Terminator */
+};
+
+static const struct attribute_group spi_hid_group = {
+ .attrs = spi_hid_attrs,
+};
+
+const struct attribute_group *spi_hid_groups[] = {
+ &spi_hid_group,
+ NULL
+};
+EXPORT_SYMBOL_GPL(spi_hid_groups);
+
+int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
+ struct spi_hid_conf *conf)
+{
+ struct device *dev = &spi->dev;
+ struct spi_hid *shid;
+ int error;
+
+ if (spi->irq <= 0)
+ return dev_err_probe(dev, spi->irq ?: -EINVAL, "Missing IRQ\n");
+
+ shid = devm_kzalloc(dev, sizeof(*shid), GFP_KERNEL);
+ if (!shid)
+ return -ENOMEM;
+
+ shid->spi = spi;
+ shid->power_state = HIDSPI_ON;
+ shid->ops = ops;
+ shid->conf = conf;
+
+ spi_set_drvdata(spi, shid);
+
+ /*
+ * At the end of probe we initialize the device:
+ * 0) assert reset, bias the interrupt line
+ * 1) sleep minimal reset delay
+ * 2) request IRQ
+ * 3) power up the device
+ * 4) deassert reset (high)
+ * After this we expect an IRQ with a reset response.
+ */
+
+ shid->ops->assert_reset(shid->ops);
+
+ shid->ops->sleep_minimal_reset_delay(shid->ops);
+
+ error = devm_request_threaded_irq(dev, spi->irq, NULL, spi_hid_dev_irq,
+ IRQF_ONESHOT, dev_name(&spi->dev), shid);
+ if (error) {
+ dev_err(dev, "%s: unable to request threaded IRQ.", __func__);
+ return error;
+ }
+
+ error = shid->ops->power_up(shid->ops);
+ if (error) {
+ dev_err(dev, "%s: could not power up.", __func__);
+ return error;
+ }
+
+ shid->ops->deassert_reset(shid->ops);
+
+ dev_dbg(dev, "%s: d3 -> %s.", __func__,
+ spi_hid_power_mode_string(shid->power_state));
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(spi_hid_core_probe);
+
+void spi_hid_core_remove(struct spi_device *spi)
+{
+ struct spi_hid *shid = spi_get_drvdata(spi);
+ struct device *dev = &spi->dev;
+ int error;
+
+ shid->ops->assert_reset(shid->ops);
+ error = shid->ops->power_down(shid->ops);
+ if (error)
+ dev_err(dev, "failed to disable regulator.");
+}
+EXPORT_SYMBOL_GPL(spi_hid_core_remove);
+
+MODULE_DESCRIPTION("HID over SPI transport driver");
+MODULE_AUTHOR("Dmitry Antipov <dmanti@microsoft.com>");
+MODULE_LICENSE("GPL");
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 04/11] HID: spi-hid: add spi-hid driver HID layer
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
` (2 preceding siblings ...)
2026-04-02 1:59 ` [PATCH v3 03/11] HID: spi-hid: add transport driver skeleton for HID over SPI bus Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 05/11] HID: spi-hid: add HID SPI protocol implementation Jingyuan Liang
` (6 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang,
Dmitry Antipov, Angela Czubak
Add HID low level driver callbacks to register SPI as a HID driver, and
an external touch device as a HID device.
Signed-off-by: Dmitry Antipov <dmanti@microsoft.com>
Signed-off-by: Angela Czubak <acz@semihalf.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
drivers/hid/spi-hid/spi-hid-core.c | 519 +++++++++++++++++++++++++++++++++++++
1 file changed, 519 insertions(+)
diff --git a/drivers/hid/spi-hid/spi-hid-core.c b/drivers/hid/spi-hid/spi-hid-core.c
index d7b4d4adad95..4723b87346d4 100644
--- a/drivers/hid/spi-hid/spi-hid-core.c
+++ b/drivers/hid/spi-hid/spi-hid-core.c
@@ -20,13 +20,69 @@
* Copyright (c) 2006-2010 Jiri Kosina
*/
+#include <linux/completion.h>
+#include <linux/crc32.h>
#include <linux/device.h>
+#include <linux/err.h>
#include <linux/hid.h>
#include <linux/hid-over-spi.h>
#include <linux/interrupt.h>
+#include <linux/jiffies.h>
#include <linux/module.h>
+#include <linux/mutex.h>
#include <linux/slab.h>
#include <linux/spi/spi.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include <linux/unaligned.h>
+
+#define SPI_HID_OUTPUT_REPORT_CONTENT_ID_DESC_REQUEST 0x00
+
+#define SPI_HID_RESP_TIMEOUT 1000
+
+/* Protocol message size constants */
+#define SPI_HID_OUTPUT_HEADER_LEN 8
+
+/* flags */
+/*
+ * ready flag indicates that the FW is ready to accept commands and
+ * requests. The FW becomes ready after sending the report descriptor.
+ */
+#define SPI_HID_READY 0
+
+/* Raw input buffer with data from the bus */
+struct spi_hid_input_buf {
+ u8 header[HIDSPI_INPUT_HEADER_SIZE];
+ u8 body[HIDSPI_INPUT_BODY_HEADER_SIZE];
+ u8 content[];
+};
+
+/* Raw output report buffer to be put on the bus */
+struct spi_hid_output_buf {
+ u8 header[SPI_HID_OUTPUT_HEADER_LEN];
+ u8 content[];
+};
+
+/* Data necessary to send an output report */
+struct spi_hid_output_report {
+ u8 report_type;
+ u16 content_length;
+ u8 content_id;
+ u8 *content;
+};
+
+/* Processed data from a device descriptor */
+struct spi_hid_device_descriptor {
+ u16 hid_version;
+ u16 report_descriptor_length;
+ u16 max_input_length;
+ u16 max_output_length;
+ u16 max_fragment_length;
+ u16 vendor_id;
+ u16 product_id;
+ u16 version_id;
+ u8 no_output_report_ack;
+};
/* struct spi_hid_conf - Conf provided to the core */
struct spi_hid_conf {
@@ -61,8 +117,26 @@ struct spi_hid {
struct spihid_ops *ops;
struct spi_hid_conf *conf;
+ struct spi_hid_device_descriptor desc; /* HID device descriptor. */
+ struct spi_hid_output_buf *output; /* Output buffer. */
+ struct spi_hid_input_buf *input; /* Input buffer. */
+ struct spi_hid_input_buf *response; /* Response buffer. */
+
+ u16 response_length;
+ u16 bufsize;
+
enum hidspi_power_state power_state;
+ u8 reset_attempts; /* The number of reset attempts. */
+
+ unsigned long flags; /* device flags. */
+
+ /* Control lock to make sure one output transaction at a time. */
+ struct mutex output_lock;
+ struct completion output_done;
+
+ u32 report_descriptor_crc32; /* HID report descriptor crc32 checksum. */
+
u32 regulator_error_count;
int regulator_last_error;
u32 bus_error_count;
@@ -70,6 +144,33 @@ struct spi_hid {
u32 dir_count; /* device initiated reset count. */
};
+static struct hid_ll_driver spi_hid_ll_driver;
+
+static void spi_hid_populate_output_header(u8 *buf,
+ const struct spi_hid_conf *conf,
+ const struct spi_hid_output_report *report)
+{
+ buf[0] = conf->write_opcode;
+ put_unaligned_be24(conf->output_report_address, &buf[1]);
+ buf[4] = report->report_type;
+ put_unaligned_le16(report->content_length, &buf[5]);
+ buf[7] = report->content_id;
+}
+
+static int spi_hid_output(struct spi_hid *shid, const void *buf, u16 length)
+{
+ int error;
+
+ error = spi_write(shid->spi, buf, length);
+
+ if (error) {
+ shid->bus_error_count++;
+ shid->bus_last_error = error;
+ }
+
+ return error;
+}
+
static const char *spi_hid_power_mode_string(enum hidspi_power_state power_state)
{
switch (power_state) {
@@ -84,11 +185,416 @@ static const char *spi_hid_power_mode_string(enum hidspi_power_state power_state
}
}
+static void spi_hid_stop_hid(struct spi_hid *shid)
+{
+ struct hid_device *hid = shid->hid;
+
+ shid->hid = NULL;
+ clear_bit(SPI_HID_READY, &shid->flags);
+
+ if (hid)
+ hid_destroy_device(hid);
+}
+
+static int spi_hid_send_output_report(struct spi_hid *shid,
+ struct spi_hid_output_report *report)
+{
+ struct spi_hid_output_buf *buf = shid->output;
+ struct device *dev = &shid->spi->dev;
+ u16 report_length;
+ u16 padded_length;
+ u8 padding;
+ int error;
+
+ guard(mutex)(&shid->output_lock);
+ if (report->content_length > shid->desc.max_output_length) {
+ dev_err(dev, "Output report too big, content_length 0x%x.",
+ report->content_length);
+ return -E2BIG;
+ }
+
+ spi_hid_populate_output_header(buf->header, shid->conf, report);
+
+ if (report->content_length)
+ memcpy(&buf->content, report->content, report->content_length);
+
+ report_length = sizeof(buf->header) + report->content_length;
+ padded_length = round_up(report_length, 4);
+ padding = padded_length - report_length;
+ memset(&buf->content[report->content_length], 0, padding);
+
+ error = spi_hid_output(shid, buf, padded_length);
+ if (error)
+ dev_err(dev, "Failed output transfer: %d.", error);
+
+ return error;
+}
+
+static int spi_hid_sync_request(struct spi_hid *shid,
+ struct spi_hid_output_report *report)
+{
+ struct device *dev = &shid->spi->dev;
+ int error;
+
+ error = spi_hid_send_output_report(shid, report);
+ if (error)
+ return error;
+
+ error = wait_for_completion_interruptible_timeout(&shid->output_done,
+ msecs_to_jiffies(SPI_HID_RESP_TIMEOUT));
+ if (error == 0) {
+ dev_err(dev, "Response timed out.");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+/*
+ * This function returns the length of the report descriptor, or a negative
+ * error code if something went wrong.
+ */
+static int spi_hid_report_descriptor_request(struct spi_hid *shid)
+{
+ struct device *dev = &shid->spi->dev;
+ struct spi_hid_output_report report = {
+ .report_type = REPORT_DESCRIPTOR,
+ .content_length = 0,
+ .content_id = SPI_HID_OUTPUT_REPORT_CONTENT_ID_DESC_REQUEST,
+ .content = NULL,
+ };
+ int ret;
+
+ ret = spi_hid_sync_request(shid, &report);
+ if (ret) {
+ dev_err(dev,
+ "Expected report descriptor not received: %d.", ret);
+ return ret;
+ }
+
+ ret = shid->response_length;
+ if (ret != shid->desc.report_descriptor_length) {
+ ret = min_t(unsigned int, ret, shid->desc.report_descriptor_length);
+ dev_err(dev, "Received report descriptor length doesn't match device descriptor field, using min of the two: %d.",
+ ret);
+ }
+
+ return ret;
+}
+
+static int spi_hid_create_device(struct spi_hid *shid)
+{
+ struct hid_device *hid;
+ struct device *dev = &shid->spi->dev;
+ int error;
+
+ hid = hid_allocate_device();
+ error = PTR_ERR_OR_ZERO(hid);
+ if (error) {
+ dev_err(dev, "Failed to allocate hid device: %d.", error);
+ return error;
+ }
+
+ hid->driver_data = shid->spi;
+ hid->ll_driver = &spi_hid_ll_driver;
+ hid->dev.parent = &shid->spi->dev;
+ hid->bus = BUS_SPI;
+ hid->version = shid->desc.hid_version;
+ hid->vendor = shid->desc.vendor_id;
+ hid->product = shid->desc.product_id;
+
+ snprintf(hid->name, sizeof(hid->name), "spi %04X:%04X",
+ hid->vendor, hid->product);
+ strscpy(hid->phys, dev_name(&shid->spi->dev), sizeof(hid->phys));
+
+ shid->hid = hid;
+
+ error = hid_add_device(hid);
+ if (error) {
+ dev_err(dev, "Failed to add hid device: %d.", error);
+ /*
+ * We likely got here because report descriptor request timed
+ * out. Let's disconnect and destroy the hid_device structure.
+ */
+ spi_hid_stop_hid(shid);
+ return error;
+ }
+
+ return 0;
+}
+
+static int spi_hid_get_request(struct spi_hid *shid, u8 content_id)
+{
+ struct device *dev = &shid->spi->dev;
+ struct spi_hid_output_report report = {
+ .report_type = GET_FEATURE,
+ .content_length = 0,
+ .content_id = content_id,
+ .content = NULL,
+ };
+ int error;
+
+ error = spi_hid_sync_request(shid, &report);
+ if (error) {
+ dev_err(dev,
+ "Expected get request response not received! Error %d.",
+ error);
+ return error;
+ }
+
+ return 0;
+}
+
+static int spi_hid_set_request(struct spi_hid *shid, u8 *arg_buf, u16 arg_len,
+ u8 content_id)
+{
+ struct spi_hid_output_report report = {
+ .report_type = SET_FEATURE,
+ .content_length = arg_len,
+ .content_id = content_id,
+ .content = arg_buf,
+ };
+
+ return spi_hid_sync_request(shid, &report);
+}
+
+/* This is a placeholder. Will be implemented in the next patch. */
static irqreturn_t spi_hid_dev_irq(int irq, void *_shid)
{
return IRQ_HANDLED;
}
+static int spi_hid_alloc_buffers(struct spi_hid *shid, size_t report_size)
+{
+ struct device *dev = &shid->spi->dev;
+ int inbufsize = sizeof(shid->input->header) + sizeof(shid->input->body) + report_size;
+ int outbufsize = sizeof(shid->output->header) + report_size;
+
+ // devm_krealloc with __GFP_ZERO ensures the new memory is initialized
+ shid->output = devm_krealloc(dev, shid->output, outbufsize, GFP_KERNEL | __GFP_ZERO);
+ shid->input = devm_krealloc(dev, shid->input, inbufsize, GFP_KERNEL | __GFP_ZERO);
+ shid->response = devm_krealloc(dev, shid->response, inbufsize, GFP_KERNEL | __GFP_ZERO);
+
+ if (!shid->output || !shid->input || !shid->response)
+ return -ENOMEM;
+
+ shid->bufsize = report_size;
+
+ return 0;
+}
+
+static int spi_hid_get_report_length(struct hid_report *report)
+{
+ return ((report->size - 1) >> 3) + 1 +
+ report->device->report_enum[report->type].numbered + 2;
+}
+
+/*
+ * Traverse the supplied list of reports and find the longest
+ */
+static void spi_hid_find_max_report(struct hid_device *hid, u32 type,
+ u16 *max)
+{
+ struct hid_report *report;
+ u16 size;
+
+ /*
+ * We should not rely on wMaxInputLength, as some devices may set it to
+ * a wrong length.
+ */
+ list_for_each_entry(report, &hid->report_enum[type].report_list, list) {
+ size = spi_hid_get_report_length(report);
+ if (*max < size)
+ *max = size;
+ }
+}
+
+/* hid_ll_driver interface functions */
+
+static int spi_hid_ll_start(struct hid_device *hid)
+{
+ struct spi_device *spi = hid->driver_data;
+ struct spi_hid *shid = spi_get_drvdata(spi);
+ int error = 0;
+ u16 bufsize = 0;
+
+ spi_hid_find_max_report(hid, HID_INPUT_REPORT, &bufsize);
+ spi_hid_find_max_report(hid, HID_OUTPUT_REPORT, &bufsize);
+ spi_hid_find_max_report(hid, HID_FEATURE_REPORT, &bufsize);
+
+ if (bufsize < HID_MIN_BUFFER_SIZE) {
+ dev_err(&spi->dev,
+ "HID_MIN_BUFFER_SIZE > max_input_length (%d).",
+ bufsize);
+ return -EINVAL;
+ }
+
+ if (bufsize > shid->bufsize) {
+ guard(disable_irq)(&shid->spi->irq);
+
+ error = spi_hid_alloc_buffers(shid, bufsize);
+ if (error)
+ return error;
+ }
+
+ return 0;
+}
+
+static void spi_hid_ll_stop(struct hid_device *hid)
+{
+ hid->claimed = 0;
+}
+
+static int spi_hid_ll_open(struct hid_device *hid)
+{
+ struct spi_device *spi = hid->driver_data;
+ struct spi_hid *shid = spi_get_drvdata(spi);
+
+ set_bit(SPI_HID_READY, &shid->flags);
+ return 0;
+}
+
+static void spi_hid_ll_close(struct hid_device *hid)
+{
+ struct spi_device *spi = hid->driver_data;
+ struct spi_hid *shid = spi_get_drvdata(spi);
+
+ clear_bit(SPI_HID_READY, &shid->flags);
+ shid->reset_attempts = 0;
+}
+
+static int spi_hid_ll_power(struct hid_device *hid, int level)
+{
+ struct spi_device *spi = hid->driver_data;
+ struct spi_hid *shid = spi_get_drvdata(spi);
+ int error = 0;
+
+ guard(mutex)(&shid->output_lock);
+ if (!shid->hid)
+ error = -ENODEV;
+
+ return error;
+}
+
+static int spi_hid_ll_parse(struct hid_device *hid)
+{
+ struct spi_device *spi = hid->driver_data;
+ struct spi_hid *shid = spi_get_drvdata(spi);
+ struct device *dev = &spi->dev;
+ int error, len;
+
+ len = spi_hid_report_descriptor_request(shid);
+ if (len < 0) {
+ dev_err(dev, "Report descriptor request failed, %d.", len);
+ return len;
+ }
+
+ /*
+ * FIXME: below call returning 0 doesn't mean that the report descriptor
+ * is good. We might be caching a crc32 of a corrupted r. d. or who
+ * knows what the FW sent. Need to have a feedback loop about r. d.
+ * being ok and only then cache it.
+ */
+ error = hid_parse_report(hid, (u8 *)shid->response->content, len);
+ if (error) {
+ dev_err(dev, "failed parsing report: %d.", error);
+ return error;
+ }
+ shid->report_descriptor_crc32 = crc32_le(0,
+ (unsigned char const *)shid->response->content,
+ len);
+
+ return 0;
+}
+
+static int spi_hid_ll_raw_request(struct hid_device *hid,
+ unsigned char reportnum, __u8 *buf,
+ size_t len, unsigned char rtype, int reqtype)
+{
+ struct spi_device *spi = hid->driver_data;
+ struct spi_hid *shid = spi_get_drvdata(spi);
+ struct device *dev = &spi->dev;
+ int ret;
+
+ switch (reqtype) {
+ case HID_REQ_SET_REPORT:
+ if (buf[0] != reportnum) {
+ dev_err(dev, "report id mismatch.");
+ return -EINVAL;
+ }
+
+ ret = spi_hid_set_request(shid, &buf[1], len - 1,
+ reportnum);
+ if (ret) {
+ dev_err(dev, "failed to set report.");
+ return ret;
+ }
+
+ ret = len;
+ break;
+ case HID_REQ_GET_REPORT:
+ ret = spi_hid_get_request(shid, reportnum);
+ if (ret) {
+ dev_err(dev, "failed to get report.");
+ return ret;
+ }
+
+ ret = min_t(size_t, len,
+ (shid->response->body[1] | (shid->response->body[2] << 8)) + 1);
+ buf[0] = shid->response->body[3];
+ memcpy(&buf[1], &shid->response->content, ret);
+ break;
+ default:
+ dev_err(dev, "invalid request type.");
+ return -EIO;
+ }
+
+ return ret;
+}
+
+static int spi_hid_ll_output_report(struct hid_device *hid, __u8 *buf,
+ size_t len)
+{
+ struct spi_device *spi = hid->driver_data;
+ struct spi_hid *shid = spi_get_drvdata(spi);
+ struct device *dev = &spi->dev;
+ struct spi_hid_output_report report = {
+ .report_type = OUTPUT_REPORT,
+ .content_length = len - 1,
+ .content_id = buf[0],
+ .content = &buf[1],
+ };
+ int error;
+
+ if (!test_bit(SPI_HID_READY, &shid->flags)) {
+ dev_err(dev, "%s called in unready state", __func__);
+ return -ENODEV;
+ }
+
+ if (shid->desc.no_output_report_ack)
+ error = spi_hid_send_output_report(shid, &report);
+ else
+ error = spi_hid_sync_request(shid, &report);
+
+ if (error) {
+ dev_err(dev, "failed to send output report.");
+ return error;
+ }
+
+ return len;
+}
+
+static struct hid_ll_driver spi_hid_ll_driver = {
+ .start = spi_hid_ll_start,
+ .stop = spi_hid_ll_stop,
+ .open = spi_hid_ll_open,
+ .close = spi_hid_ll_close,
+ .power = spi_hid_ll_power,
+ .parse = spi_hid_ll_parse,
+ .output_report = spi_hid_ll_output_report,
+ .raw_request = spi_hid_ll_raw_request,
+};
+
static ssize_t bus_error_count_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
@@ -159,6 +665,15 @@ int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
spi_set_drvdata(spi, shid);
+ /*
+ * we need to allocate the buffer without knowing the maximum
+ * size of the reports. Let's use SZ_2K, then we do the
+ * real computation later.
+ */
+ error = spi_hid_alloc_buffers(shid, SZ_2K);
+ if (error)
+ return error;
+
/*
* At the end of probe we initialize the device:
* 0) assert reset, bias the interrupt line
@@ -191,6 +706,8 @@ int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
dev_dbg(dev, "%s: d3 -> %s.", __func__,
spi_hid_power_mode_string(shid->power_state));
+ spi_hid_create_device(shid);
+
return 0;
}
EXPORT_SYMBOL_GPL(spi_hid_core_probe);
@@ -201,6 +718,8 @@ void spi_hid_core_remove(struct spi_device *spi)
struct device *dev = &spi->dev;
int error;
+ spi_hid_stop_hid(shid);
+
shid->ops->assert_reset(shid->ops);
error = shid->ops->power_down(shid->ops);
if (error)
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 05/11] HID: spi-hid: add HID SPI protocol implementation
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
` (3 preceding siblings ...)
2026-04-02 1:59 ` [PATCH v3 04/11] HID: spi-hid: add spi-hid driver HID layer Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 06/11] HID: spi_hid: add spi_hid traces Jingyuan Liang
` (5 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang,
Dmitry Antipov, Angela Czubak
This driver follows HID Over SPI Protocol Specification 1.0 available at
https://www.microsoft.com/en-us/download/details.aspx?id=103325. The
initial version of the driver does not support: 1) multi-fragment input
reports, 2) sending GET_INPUT and COMMAND output report types and
processing their respective acknowledge input reports, and 3) device
sleep power state.
Signed-off-by: Dmitry Antipov <dmanti@microsoft.com>
Signed-off-by: Angela Czubak <acz@semihalf.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
drivers/hid/spi-hid/spi-hid-core.c | 582 ++++++++++++++++++++++++++++++++++++-
1 file changed, 572 insertions(+), 10 deletions(-)
diff --git a/drivers/hid/spi-hid/spi-hid-core.c b/drivers/hid/spi-hid/spi-hid-core.c
index 4723b87346d4..00b9718ba2c3 100644
--- a/drivers/hid/spi-hid/spi-hid-core.c
+++ b/drivers/hid/spi-hid/spi-hid-core.c
@@ -23,11 +23,16 @@
#include <linux/completion.h>
#include <linux/crc32.h>
#include <linux/device.h>
+#include <linux/dma-mapping.h>
#include <linux/err.h>
#include <linux/hid.h>
#include <linux/hid-over-spi.h>
+#include <linux/input.h>
#include <linux/interrupt.h>
+#include <linux/irq.h>
#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/slab.h>
@@ -35,12 +40,22 @@
#include <linux/string.h>
#include <linux/sysfs.h>
#include <linux/unaligned.h>
+#include <linux/wait.h>
+#include <linux/workqueue.h>
+
+/* Protocol constants */
+#define SPI_HID_READ_APPROVAL_CONSTANT 0xff
+#define SPI_HID_INPUT_HEADER_SYNC_BYTE 0x5a
+#define SPI_HID_INPUT_HEADER_VERSION 0x03
+#define SPI_HID_SUPPORTED_VERSION 0x0300
#define SPI_HID_OUTPUT_REPORT_CONTENT_ID_DESC_REQUEST 0x00
-#define SPI_HID_RESP_TIMEOUT 1000
+#define SPI_HID_MAX_RESET_ATTEMPTS 3
+#define SPI_HID_RESP_TIMEOUT 1000
/* Protocol message size constants */
+#define SPI_HID_READ_APPROVAL_LEN 5
#define SPI_HID_OUTPUT_HEADER_LEN 8
/* flags */
@@ -49,6 +64,22 @@
* requests. The FW becomes ready after sending the report descriptor.
*/
#define SPI_HID_READY 0
+/*
+ * refresh_in_progress is set to true while the refresh_device worker
+ * thread is destroying and recreating the hidraw device. When this flag
+ * is set to true, the ll_close and ll_open functions will not cause
+ * power state changes.
+ */
+#define SPI_HID_REFRESH_IN_PROGRESS 1
+/*
+ * reset_pending indicates that the device is being reset. When this flag
+ * is set to true, garbage interrupts triggered during reset will be
+ * dropped and will not cause error handling.
+ */
+#define SPI_HID_RESET_PENDING 2
+#define SPI_HID_RESET_RESPONSE 3
+#define SPI_HID_CREATE_DEVICE 4
+#define SPI_HID_ERROR 5
/* Raw input buffer with data from the bus */
struct spi_hid_input_buf {
@@ -57,6 +88,22 @@ struct spi_hid_input_buf {
u8 content[];
};
+/* Processed data from input report header */
+struct spi_hid_input_header {
+ u8 version;
+ u16 report_length;
+ u8 last_fragment_flag;
+ u8 sync_const;
+};
+
+/* Processed data from an input report */
+struct spi_hid_input_report {
+ u8 report_type;
+ u16 content_length;
+ u8 content_id;
+ u8 *content;
+};
+
/* Raw output report buffer to be put on the bus */
struct spi_hid_output_buf {
u8 header[SPI_HID_OUTPUT_HEADER_LEN];
@@ -114,6 +161,9 @@ struct spi_hid {
struct spi_device *spi; /* spi device. */
struct hid_device *hid; /* pointer to corresponding HID dev. */
+ struct spi_transfer input_transfer[2]; /* Transfer buffer for read and write. */
+ struct spi_message input_message; /* used to execute a sequence of spi transfers. */
+
struct spihid_ops *ops;
struct spi_hid_conf *conf;
@@ -131,10 +181,20 @@ struct spi_hid {
unsigned long flags; /* device flags. */
- /* Control lock to make sure one output transaction at a time. */
+ struct work_struct reset_work;
+
+ /* Control lock to ensure complete output transaction. */
struct mutex output_lock;
+ /* Power lock to make sure one power state change at a time. */
+ struct mutex power_lock;
+ /* I/O lock to prevent concurrent output writes during the input read. */
+ struct mutex io_lock;
+
struct completion output_done;
+ u8 read_approval_header[SPI_HID_READ_APPROVAL_LEN];
+ u8 read_approval_body[SPI_HID_READ_APPROVAL_LEN];
+
u32 report_descriptor_crc32; /* HID report descriptor crc32 checksum. */
u32 regulator_error_count;
@@ -146,6 +206,66 @@ struct spi_hid {
static struct hid_ll_driver spi_hid_ll_driver;
+static void spi_hid_populate_read_approvals(const struct spi_hid_conf *conf,
+ u8 *header_buf, u8 *body_buf)
+{
+ header_buf[0] = conf->read_opcode;
+ put_unaligned_be24(conf->input_report_header_address, &header_buf[1]);
+ header_buf[4] = SPI_HID_READ_APPROVAL_CONSTANT;
+
+ body_buf[0] = conf->read_opcode;
+ put_unaligned_be24(conf->input_report_body_address, &body_buf[1]);
+ body_buf[4] = SPI_HID_READ_APPROVAL_CONSTANT;
+}
+
+static void spi_hid_parse_dev_desc(const struct hidspi_dev_descriptor *raw,
+ struct spi_hid_device_descriptor *desc)
+{
+ desc->hid_version = le16_to_cpu(raw->bcd_ver);
+ desc->report_descriptor_length = le16_to_cpu(raw->rep_desc_len);
+ desc->max_input_length = le16_to_cpu(raw->max_input_len);
+ desc->max_output_length = le16_to_cpu(raw->max_output_len);
+
+ /* FIXME: multi-fragment not supported, field below not used */
+ desc->max_fragment_length = le16_to_cpu(raw->max_frag_len);
+
+ desc->vendor_id = le16_to_cpu(raw->vendor_id);
+ desc->product_id = le16_to_cpu(raw->product_id);
+ desc->version_id = le16_to_cpu(raw->version_id);
+ desc->no_output_report_ack = le16_to_cpu(raw->flags) & BIT(0);
+}
+
+static void spi_hid_populate_input_header(const u8 *buf,
+ struct spi_hid_input_header *header)
+{
+ header->version = buf[0] & 0xf;
+ header->report_length = (get_unaligned_le16(&buf[1]) & 0x3fff) * 4;
+ header->last_fragment_flag = (buf[2] & 0x40) >> 6;
+ header->sync_const = buf[3];
+}
+
+static void spi_hid_populate_input_body(const u8 *buf,
+ struct input_report_body_header *body)
+{
+ body->input_report_type = buf[0];
+ body->content_len = get_unaligned_le16(&buf[1]);
+ body->content_id = buf[3];
+}
+
+static void spi_hid_input_report_prepare(struct spi_hid_input_buf *buf,
+ struct spi_hid_input_report *report)
+{
+ struct spi_hid_input_header header;
+ struct input_report_body_header body;
+
+ spi_hid_populate_input_header(buf->header, &header);
+ spi_hid_populate_input_body(buf->body, &body);
+ report->report_type = body.input_report_type;
+ report->content_length = body.content_len;
+ report->content_id = body.content_id;
+ report->content = buf->content;
+}
+
static void spi_hid_populate_output_header(u8 *buf,
const struct spi_hid_conf *conf,
const struct spi_hid_output_report *report)
@@ -157,6 +277,33 @@ static void spi_hid_populate_output_header(u8 *buf,
buf[7] = report->content_id;
}
+static int spi_hid_input_sync(struct spi_hid *shid, void *buf, u16 length,
+ bool is_header)
+{
+ int error;
+
+ shid->input_transfer[0].tx_buf = is_header ?
+ shid->read_approval_header :
+ shid->read_approval_body;
+ shid->input_transfer[0].len = SPI_HID_READ_APPROVAL_LEN;
+
+ shid->input_transfer[1].rx_buf = buf;
+ shid->input_transfer[1].len = length;
+
+ spi_message_init_with_transfers(&shid->input_message,
+ shid->input_transfer, 2);
+
+ error = spi_sync(shid->spi, &shid->input_message);
+ if (error) {
+ dev_err(&shid->spi->dev, "Error starting sync transfer: %d.", error);
+ shid->bus_error_count++;
+ shid->bus_last_error = error;
+ return error;
+ }
+
+ return 0;
+}
+
static int spi_hid_output(struct spi_hid *shid, const void *buf, u16 length)
{
int error;
@@ -196,6 +343,50 @@ static void spi_hid_stop_hid(struct spi_hid *shid)
hid_destroy_device(hid);
}
+static void spi_hid_error(struct spi_hid *shid)
+{
+ struct device *dev = &shid->spi->dev;
+ int error;
+
+ guard(mutex)(&shid->power_lock);
+ if (shid->power_state == HIDSPI_OFF)
+ return;
+
+ if (shid->reset_attempts++ >= SPI_HID_MAX_RESET_ATTEMPTS) {
+ dev_err(dev, "unresponsive device, aborting.");
+ spi_hid_stop_hid(shid);
+ shid->ops->assert_reset(shid->ops);
+ error = shid->ops->power_down(shid->ops);
+ if (error) {
+ dev_err(dev, "failed to disable regulator.");
+ shid->regulator_error_count++;
+ shid->regulator_last_error = error;
+ }
+ return;
+ }
+
+ clear_bit(SPI_HID_READY, &shid->flags);
+ set_bit(SPI_HID_RESET_PENDING, &shid->flags);
+
+ shid->ops->assert_reset(shid->ops);
+
+ shid->power_state = HIDSPI_OFF;
+
+ /*
+ * We want to cancel pending reset work as the device is being reset
+ * to recover from an error. cancel_work_sync will put us in a deadlock
+ * because this function is scheduled in 'reset_work' and we should
+ * avoid waiting for itself.
+ */
+ cancel_work(&shid->reset_work);
+
+ shid->ops->sleep_minimal_reset_delay(shid->ops);
+
+ shid->power_state = HIDSPI_ON;
+
+ shid->ops->deassert_reset(shid->ops);
+}
+
static int spi_hid_send_output_report(struct spi_hid *shid,
struct spi_hid_output_report *report)
{
@@ -206,13 +397,13 @@ static int spi_hid_send_output_report(struct spi_hid *shid,
u8 padding;
int error;
- guard(mutex)(&shid->output_lock);
if (report->content_length > shid->desc.max_output_length) {
dev_err(dev, "Output report too big, content_length 0x%x.",
report->content_length);
return -E2BIG;
}
+ guard(mutex)(&shid->io_lock);
spi_hid_populate_output_header(buf->header, shid->conf, report);
if (report->content_length)
@@ -236,6 +427,7 @@ static int spi_hid_sync_request(struct spi_hid *shid,
struct device *dev = &shid->spi->dev;
int error;
+ guard(mutex)(&shid->output_lock);
error = spi_hid_send_output_report(shid, report);
if (error)
return error;
@@ -250,6 +442,86 @@ static int spi_hid_sync_request(struct spi_hid *shid,
return 0;
}
+/*
+ * Handle the reset response from the FW by sending a request for the device
+ * descriptor.
+ */
+static void spi_hid_reset_response(struct spi_hid *shid)
+{
+ struct device *dev = &shid->spi->dev;
+ struct spi_hid_output_report report = {
+ .report_type = DEVICE_DESCRIPTOR,
+ .content_length = 0x0,
+ .content_id = SPI_HID_OUTPUT_REPORT_CONTENT_ID_DESC_REQUEST,
+ .content = NULL,
+ };
+ int error;
+
+ if (test_bit(SPI_HID_READY, &shid->flags)) {
+ dev_err(dev, "Spontaneous FW reset!");
+ clear_bit(SPI_HID_READY, &shid->flags);
+ shid->dir_count++;
+ }
+
+ if (shid->power_state == HIDSPI_OFF)
+ return;
+
+ error = spi_hid_sync_request(shid, &report);
+ if (error) {
+ dev_WARN_ONCE(dev, true,
+ "Failed to send device descriptor request: %d.", error);
+ set_bit(SPI_HID_ERROR, &shid->flags);
+ schedule_work(&shid->reset_work);
+ }
+}
+
+static int spi_hid_input_report_handler(struct spi_hid *shid,
+ struct spi_hid_input_buf *buf)
+{
+ struct device *dev = &shid->spi->dev;
+ struct spi_hid_input_report r;
+ int error = 0;
+
+ if (!test_bit(SPI_HID_READY, &shid->flags) ||
+ test_bit(SPI_HID_REFRESH_IN_PROGRESS, &shid->flags) || !shid->hid) {
+ dev_err(dev, "HID not ready");
+ return 0;
+ }
+
+ spi_hid_input_report_prepare(buf, &r);
+
+ error = hid_input_report(shid->hid, HID_INPUT_REPORT,
+ r.content - 1, r.content_length + 1, 1);
+
+ if (error == -ENODEV || error == -EBUSY) {
+ dev_err(dev, "ignoring report --> %d.", error);
+ return 0;
+ } else if (error) {
+ dev_err(dev, "Bad input report: %d.", error);
+ }
+
+ return error;
+}
+
+static void spi_hid_response_handler(struct spi_hid *shid,
+ struct input_report_body_header *body)
+{
+ shid->response_length = body->content_len;
+ /* completion_done returns 0 if there are waiters, otherwise 1 */
+ if (completion_done(&shid->output_done)) {
+ dev_err(&shid->spi->dev, "Unexpected response report.");
+ } else {
+ if (body->input_report_type == REPORT_DESCRIPTOR_RESPONSE ||
+ body->input_report_type == GET_FEATURE_RESPONSE) {
+ memcpy(shid->response->body, shid->input->body,
+ sizeof(shid->input->body));
+ memcpy(shid->response->content, shid->input->content,
+ body->content_len);
+ }
+ complete(&shid->output_done);
+ }
+}
+
/*
* This function returns the length of the report descriptor, or a negative
* error code if something went wrong.
@@ -269,6 +541,8 @@ static int spi_hid_report_descriptor_request(struct spi_hid *shid)
if (ret) {
dev_err(dev,
"Expected report descriptor not received: %d.", ret);
+ set_bit(SPI_HID_ERROR, &shid->flags);
+ schedule_work(&shid->reset_work);
return ret;
}
@@ -323,6 +597,205 @@ static int spi_hid_create_device(struct spi_hid *shid)
return 0;
}
+static void spi_hid_refresh_device(struct spi_hid *shid)
+{
+ struct device *dev = &shid->spi->dev;
+ u32 new_crc32 = 0;
+ int error = 0;
+
+ error = spi_hid_report_descriptor_request(shid);
+ if (error < 0) {
+ dev_err(dev,
+ "%s: failed report descriptor request: %d",
+ __func__, error);
+ return;
+ }
+ new_crc32 = crc32_le(0, (unsigned char const *)shid->response->content,
+ (size_t)error);
+
+ /* Same report descriptor, so no need to create a new hid device. */
+ if (new_crc32 == shid->report_descriptor_crc32) {
+ set_bit(SPI_HID_READY, &shid->flags);
+ return;
+ }
+
+ shid->report_descriptor_crc32 = new_crc32;
+
+ set_bit(SPI_HID_REFRESH_IN_PROGRESS, &shid->flags);
+
+ spi_hid_stop_hid(shid);
+
+ error = spi_hid_create_device(shid);
+ if (error) {
+ dev_err(dev, "%s: Failed to create hid device: %d.", __func__, error);
+ return;
+ }
+
+ clear_bit(SPI_HID_REFRESH_IN_PROGRESS, &shid->flags);
+}
+
+static void spi_hid_reset_work(struct work_struct *work)
+{
+ struct spi_hid *shid =
+ container_of(work, struct spi_hid, reset_work);
+ struct device *dev = &shid->spi->dev;
+ int error = 0;
+
+ if (test_and_clear_bit(SPI_HID_RESET_RESPONSE, &shid->flags)) {
+ spi_hid_reset_response(shid);
+ return;
+ }
+
+ if (test_and_clear_bit(SPI_HID_CREATE_DEVICE, &shid->flags)) {
+ guard(mutex)(&shid->power_lock);
+ if (shid->power_state == HIDSPI_OFF) {
+ dev_err(dev, "%s: Powered off, returning", __func__);
+ return;
+ }
+
+ if (!shid->hid) {
+ error = spi_hid_create_device(shid);
+ if (error) {
+ dev_err(dev, "%s: Failed to create hid device: %d.",
+ __func__, error);
+ return;
+ }
+ } else {
+ spi_hid_refresh_device(shid);
+ }
+
+ return;
+ }
+
+ if (test_and_clear_bit(SPI_HID_ERROR, &shid->flags)) {
+ spi_hid_error(shid);
+ return;
+ }
+}
+
+static int spi_hid_process_input_report(struct spi_hid *shid,
+ struct spi_hid_input_buf *buf)
+{
+ struct spi_hid_input_header header;
+ struct input_report_body_header body;
+ struct device *dev = &shid->spi->dev;
+ struct hidspi_dev_descriptor *raw;
+
+ spi_hid_populate_input_header(buf->header, &header);
+ spi_hid_populate_input_body(buf->body, &body);
+
+ if (body.content_len > header.report_length) {
+ dev_err(dev, "Bad body length %d > %d.", body.content_len,
+ header.report_length);
+ return -EPROTO;
+ }
+
+ switch (body.input_report_type) {
+ case DATA:
+ return spi_hid_input_report_handler(shid, buf);
+ case RESET_RESPONSE:
+ clear_bit(SPI_HID_RESET_PENDING, &shid->flags);
+ set_bit(SPI_HID_RESET_RESPONSE, &shid->flags);
+ schedule_work(&shid->reset_work);
+ break;
+ case DEVICE_DESCRIPTOR_RESPONSE:
+ /* Mark the completion done to avoid timeout */
+ spi_hid_response_handler(shid, &body);
+
+ /* Reset attempts at every device descriptor fetch */
+ shid->reset_attempts = 0;
+ raw = (struct hidspi_dev_descriptor *)buf->content;
+
+ /* Validate device descriptor length before parsing */
+ if (body.content_len != HIDSPI_DEVICE_DESCRIPTOR_SIZE) {
+ dev_err(dev, "Invalid content length %d, expected %lu.",
+ body.content_len,
+ HIDSPI_DEVICE_DESCRIPTOR_SIZE);
+ return -EPROTO;
+ }
+
+ if (le16_to_cpu(raw->dev_desc_len) !=
+ HIDSPI_DEVICE_DESCRIPTOR_SIZE) {
+ dev_err(dev,
+ "Invalid wDeviceDescLength %d, expected %lu.",
+ raw->dev_desc_len,
+ HIDSPI_DEVICE_DESCRIPTOR_SIZE);
+ return -EPROTO;
+ }
+
+ spi_hid_parse_dev_desc(raw, &shid->desc);
+
+ if (shid->desc.hid_version != SPI_HID_SUPPORTED_VERSION) {
+ dev_err(dev,
+ "Unsupported device descriptor version %4x.",
+ shid->desc.hid_version);
+ return -EPROTONOSUPPORT;
+ }
+
+ set_bit(SPI_HID_CREATE_DEVICE, &shid->flags);
+ schedule_work(&shid->reset_work);
+
+ break;
+ case OUTPUT_REPORT_RESPONSE:
+ if (shid->desc.no_output_report_ack) {
+ dev_err(dev, "Unexpected output report response.");
+ break;
+ }
+ fallthrough;
+ case GET_FEATURE_RESPONSE:
+ case SET_FEATURE_RESPONSE:
+ case REPORT_DESCRIPTOR_RESPONSE:
+ spi_hid_response_handler(shid, &body);
+ break;
+ /*
+ * FIXME: sending GET_INPUT and COMMAND reports not supported, thus
+ * throw away responses to those, they should never come.
+ */
+ case GET_INPUT_REPORT_RESPONSE:
+ case COMMAND_RESPONSE:
+ dev_err(dev, "Not a supported report type: 0x%x.",
+ body.input_report_type);
+ break;
+ default:
+ dev_err(dev, "Unknown input report: 0x%x.", body.input_report_type);
+ return -EPROTO;
+ }
+
+ return 0;
+}
+
+static int spi_hid_bus_validate_header(struct spi_hid *shid,
+ struct spi_hid_input_header *header)
+{
+ struct device *dev = &shid->spi->dev;
+
+ if (header->version != SPI_HID_INPUT_HEADER_VERSION) {
+ dev_err(dev, "Unknown input report version (v 0x%x).",
+ header->version);
+ return -EINVAL;
+ }
+
+ if (shid->desc.max_input_length != 0 &&
+ header->report_length > shid->desc.max_input_length) {
+ dev_err(dev, "Input report body size %u > max expected of %u.",
+ header->report_length, shid->desc.max_input_length);
+ return -EMSGSIZE;
+ }
+
+ if (header->last_fragment_flag != 1) {
+ dev_err(dev, "Multi-fragment reports not supported.");
+ return -EOPNOTSUPP;
+ }
+
+ if (header->sync_const != SPI_HID_INPUT_HEADER_SYNC_BYTE) {
+ dev_err(dev, "Invalid input report sync constant (0x%x).",
+ header->sync_const);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
static int spi_hid_get_request(struct spi_hid *shid, u8 content_id)
{
struct device *dev = &shid->spi->dev;
@@ -339,6 +812,8 @@ static int spi_hid_get_request(struct spi_hid *shid, u8 content_id)
dev_err(dev,
"Expected get request response not received! Error %d.",
error);
+ set_bit(SPI_HID_ERROR, &shid->flags);
+ schedule_work(&shid->reset_work);
return error;
}
@@ -358,9 +833,83 @@ static int spi_hid_set_request(struct spi_hid *shid, u8 *arg_buf, u16 arg_len,
return spi_hid_sync_request(shid, &report);
}
-/* This is a placeholder. Will be implemented in the next patch. */
static irqreturn_t spi_hid_dev_irq(int irq, void *_shid)
{
+ struct spi_hid *shid = _shid;
+ struct device *dev = &shid->spi->dev;
+ struct spi_hid_input_header header;
+ int error = 0;
+
+ scoped_guard(mutex, &shid->io_lock) {
+ error = spi_hid_input_sync(shid, shid->input->header,
+ sizeof(shid->input->header), true);
+ if (error) {
+ dev_err(dev, "Failed to transfer header: %d.", error);
+ goto err;
+ }
+
+ if (shid->power_state == HIDSPI_OFF) {
+ dev_warn(dev, "Device is off after header was received.");
+ goto out;
+ }
+
+ if (shid->input_message.status < 0) {
+ dev_warn(dev, "Error reading header: %d.",
+ shid->input_message.status);
+ shid->bus_error_count++;
+ shid->bus_last_error = shid->input_message.status;
+ goto err;
+ }
+
+ spi_hid_populate_input_header(shid->input->header, &header);
+
+ error = spi_hid_bus_validate_header(shid, &header);
+ if (error) {
+ if (!test_bit(SPI_HID_RESET_PENDING, &shid->flags)) {
+ dev_err(dev, "Failed to validate header: %d.", error);
+ print_hex_dump(KERN_ERR, "spi_hid: header buffer: ",
+ DUMP_PREFIX_NONE, 16, 1, shid->input->header,
+ sizeof(shid->input->header), false);
+ shid->bus_error_count++;
+ shid->bus_last_error = error;
+ goto err;
+ }
+ goto out;
+ }
+
+ error = spi_hid_input_sync(shid, shid->input->body, header.report_length,
+ false);
+ if (error) {
+ dev_err(dev, "Failed to transfer body: %d.", error);
+ goto err;
+ }
+
+ if (shid->power_state == HIDSPI_OFF) {
+ dev_warn(dev, "Device is off after body was received.");
+ goto out;
+ }
+
+ if (shid->input_message.status < 0) {
+ dev_warn(dev, "Error reading body: %d.",
+ shid->input_message.status);
+ shid->bus_error_count++;
+ shid->bus_last_error = shid->input_message.status;
+ goto err;
+ }
+ }
+
+ error = spi_hid_process_input_report(shid, shid->input);
+ if (error) {
+ dev_err(dev, "Failed to process input report: %d.", error);
+ goto err;
+ }
+
+out:
+ return IRQ_HANDLED;
+
+err:
+ set_bit(SPI_HID_ERROR, &shid->flags);
+ schedule_work(&shid->reset_work);
return IRQ_HANDLED;
}
@@ -571,10 +1120,13 @@ static int spi_hid_ll_output_report(struct hid_device *hid, __u8 *buf,
return -ENODEV;
}
- if (shid->desc.no_output_report_ack)
- error = spi_hid_send_output_report(shid, &report);
- else
+ if (shid->desc.no_output_report_ack) {
+ scoped_guard(mutex, &shid->output_lock) {
+ error = spi_hid_send_output_report(shid, &report);
+ }
+ } else {
error = spi_hid_sync_request(shid, &report);
+ }
if (error) {
dev_err(dev, "failed to send output report.");
@@ -662,11 +1214,23 @@ int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
shid->power_state = HIDSPI_ON;
shid->ops = ops;
shid->conf = conf;
+ set_bit(SPI_HID_RESET_PENDING, &shid->flags);
spi_set_drvdata(spi, shid);
+ /* Using now populated conf let's pre-calculate the read approvals */
+ spi_hid_populate_read_approvals(shid->conf, shid->read_approval_header,
+ shid->read_approval_body);
+
+ mutex_init(&shid->output_lock);
+ mutex_init(&shid->power_lock);
+ mutex_init(&shid->io_lock);
+ init_completion(&shid->output_done);
+
+ INIT_WORK(&shid->reset_work, spi_hid_reset_work);
+
/*
- * we need to allocate the buffer without knowing the maximum
+ * We need to allocate the buffer without knowing the maximum
* size of the reports. Let's use SZ_2K, then we do the
* real computation later.
*/
@@ -706,8 +1270,6 @@ int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
dev_dbg(dev, "%s: d3 -> %s.", __func__,
spi_hid_power_mode_string(shid->power_state));
- spi_hid_create_device(shid);
-
return 0;
}
EXPORT_SYMBOL_GPL(spi_hid_core_probe);
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 06/11] HID: spi_hid: add spi_hid traces
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
` (4 preceding siblings ...)
2026-04-02 1:59 ` [PATCH v3 05/11] HID: spi-hid: add HID SPI protocol implementation Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 07/11] HID: spi_hid: add ACPI support for SPI over HID Jingyuan Liang
` (4 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang,
Dmitry Antipov, Angela Czubak
Add traces for purposed of debugging spi_hid driver.
Signed-off-by: Dmitry Antipov <dmanti@microsoft.com>
Signed-off-by: Angela Czubak <acz@semihalf.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
drivers/hid/spi-hid/Makefile | 1 +
drivers/hid/spi-hid/spi-hid-core.c | 118 +++++++++----------------
drivers/hid/spi-hid/spi-hid-core.h | 91 +++++++++++++++++++
drivers/hid/spi-hid/spi-hid-trace.h | 169 ++++++++++++++++++++++++++++++++++++
4 files changed, 303 insertions(+), 76 deletions(-)
diff --git a/drivers/hid/spi-hid/Makefile b/drivers/hid/spi-hid/Makefile
index 92e24cddbfc2..733e006df56e 100644
--- a/drivers/hid/spi-hid/Makefile
+++ b/drivers/hid/spi-hid/Makefile
@@ -7,3 +7,4 @@
obj-$(CONFIG_SPI_HID_CORE) += spi-hid.o
spi-hid-objs = spi-hid-core.o
+CFLAGS_spi-hid-core.o := -I$(src)
diff --git a/drivers/hid/spi-hid/spi-hid-core.c b/drivers/hid/spi-hid/spi-hid-core.c
index 00b9718ba2c3..802615565541 100644
--- a/drivers/hid/spi-hid/spi-hid-core.c
+++ b/drivers/hid/spi-hid/spi-hid-core.c
@@ -43,6 +43,11 @@
#include <linux/wait.h>
#include <linux/workqueue.h>
+#include "spi-hid-core.h"
+
+#define CREATE_TRACE_POINTS
+#include "spi-hid-trace.h"
+
/* Protocol constants */
#define SPI_HID_READ_APPROVAL_CONSTANT 0xff
#define SPI_HID_INPUT_HEADER_SYNC_BYTE 0x5a
@@ -81,13 +86,6 @@
#define SPI_HID_CREATE_DEVICE 4
#define SPI_HID_ERROR 5
-/* Raw input buffer with data from the bus */
-struct spi_hid_input_buf {
- u8 header[HIDSPI_INPUT_HEADER_SIZE];
- u8 body[HIDSPI_INPUT_BODY_HEADER_SIZE];
- u8 content[];
-};
-
/* Processed data from input report header */
struct spi_hid_input_header {
u8 version;
@@ -104,12 +102,6 @@ struct spi_hid_input_report {
u8 *content;
};
-/* Raw output report buffer to be put on the bus */
-struct spi_hid_output_buf {
- u8 header[SPI_HID_OUTPUT_HEADER_LEN];
- u8 content[];
-};
-
/* Data necessary to send an output report */
struct spi_hid_output_report {
u8 report_type;
@@ -118,19 +110,6 @@ struct spi_hid_output_report {
u8 *content;
};
-/* Processed data from a device descriptor */
-struct spi_hid_device_descriptor {
- u16 hid_version;
- u16 report_descriptor_length;
- u16 max_input_length;
- u16 max_output_length;
- u16 max_fragment_length;
- u16 vendor_id;
- u16 product_id;
- u16 version_id;
- u8 no_output_report_ack;
-};
-
/* struct spi_hid_conf - Conf provided to the core */
struct spi_hid_conf {
u32 input_report_header_address;
@@ -156,54 +135,6 @@ struct spihid_ops {
void (*sleep_minimal_reset_delay)(struct spihid_ops *ops);
};
-/* Driver context */
-struct spi_hid {
- struct spi_device *spi; /* spi device. */
- struct hid_device *hid; /* pointer to corresponding HID dev. */
-
- struct spi_transfer input_transfer[2]; /* Transfer buffer for read and write. */
- struct spi_message input_message; /* used to execute a sequence of spi transfers. */
-
- struct spihid_ops *ops;
- struct spi_hid_conf *conf;
-
- struct spi_hid_device_descriptor desc; /* HID device descriptor. */
- struct spi_hid_output_buf *output; /* Output buffer. */
- struct spi_hid_input_buf *input; /* Input buffer. */
- struct spi_hid_input_buf *response; /* Response buffer. */
-
- u16 response_length;
- u16 bufsize;
-
- enum hidspi_power_state power_state;
-
- u8 reset_attempts; /* The number of reset attempts. */
-
- unsigned long flags; /* device flags. */
-
- struct work_struct reset_work;
-
- /* Control lock to ensure complete output transaction. */
- struct mutex output_lock;
- /* Power lock to make sure one power state change at a time. */
- struct mutex power_lock;
- /* I/O lock to prevent concurrent output writes during the input read. */
- struct mutex io_lock;
-
- struct completion output_done;
-
- u8 read_approval_header[SPI_HID_READ_APPROVAL_LEN];
- u8 read_approval_body[SPI_HID_READ_APPROVAL_LEN];
-
- u32 report_descriptor_crc32; /* HID report descriptor crc32 checksum. */
-
- u32 regulator_error_count;
- int regulator_last_error;
- u32 bus_error_count;
- int bus_last_error;
- u32 dir_count; /* device initiated reset count. */
-};
-
static struct hid_ll_driver spi_hid_ll_driver;
static void spi_hid_populate_read_approvals(const struct spi_hid_conf *conf,
@@ -293,6 +224,11 @@ static int spi_hid_input_sync(struct spi_hid *shid, void *buf, u16 length,
spi_message_init_with_transfers(&shid->input_message,
shid->input_transfer, 2);
+ trace_spi_hid_input_sync(shid, shid->input_transfer[0].tx_buf,
+ shid->input_transfer[0].len,
+ shid->input_transfer[1].rx_buf,
+ shid->input_transfer[1].len, 0);
+
error = spi_sync(shid->spi, &shid->input_message);
if (error) {
dev_err(&shid->spi->dev, "Error starting sync transfer: %d.", error);
@@ -343,11 +279,13 @@ static void spi_hid_stop_hid(struct spi_hid *shid)
hid_destroy_device(hid);
}
-static void spi_hid_error(struct spi_hid *shid)
+static void spi_hid_error_handler(struct spi_hid *shid)
{
struct device *dev = &shid->spi->dev;
int error;
+ trace_spi_hid_error_handler(shid);
+
guard(mutex)(&shid->power_lock);
if (shid->power_state == HIDSPI_OFF)
return;
@@ -457,6 +395,8 @@ static void spi_hid_reset_response(struct spi_hid *shid)
};
int error;
+ trace_spi_hid_reset_response(shid);
+
if (test_bit(SPI_HID_READY, &shid->flags)) {
dev_err(dev, "Spontaneous FW reset!");
clear_bit(SPI_HID_READY, &shid->flags);
@@ -482,6 +422,8 @@ static int spi_hid_input_report_handler(struct spi_hid *shid,
struct spi_hid_input_report r;
int error = 0;
+ trace_spi_hid_input_report_handler(shid);
+
if (!test_bit(SPI_HID_READY, &shid->flags) ||
test_bit(SPI_HID_REFRESH_IN_PROGRESS, &shid->flags) || !shid->hid) {
dev_err(dev, "HID not ready");
@@ -506,6 +448,8 @@ static int spi_hid_input_report_handler(struct spi_hid *shid,
static void spi_hid_response_handler(struct spi_hid *shid,
struct input_report_body_header *body)
{
+ trace_spi_hid_response_handler(shid);
+
shid->response_length = body->content_len;
/* completion_done returns 0 if there are waiters, otherwise 1 */
if (completion_done(&shid->output_done)) {
@@ -562,6 +506,8 @@ static int spi_hid_create_device(struct spi_hid *shid)
struct device *dev = &shid->spi->dev;
int error;
+ trace_spi_hid_create_device(shid);
+
hid = hid_allocate_device();
error = PTR_ERR_OR_ZERO(hid);
if (error) {
@@ -603,6 +549,8 @@ static void spi_hid_refresh_device(struct spi_hid *shid)
u32 new_crc32 = 0;
int error = 0;
+ trace_spi_hid_refresh_device(shid);
+
error = spi_hid_report_descriptor_request(shid);
if (error < 0) {
dev_err(dev,
@@ -668,7 +616,7 @@ static void spi_hid_reset_work(struct work_struct *work)
}
if (test_and_clear_bit(SPI_HID_ERROR, &shid->flags)) {
- spi_hid_error(shid);
+ spi_hid_error_handler(shid);
return;
}
}
@@ -681,6 +629,8 @@ static int spi_hid_process_input_report(struct spi_hid *shid,
struct device *dev = &shid->spi->dev;
struct hidspi_dev_descriptor *raw;
+ trace_spi_hid_process_input_report(shid);
+
spi_hid_populate_input_header(buf->header, &header);
spi_hid_populate_input_body(buf->body, &body);
@@ -840,6 +790,9 @@ static irqreturn_t spi_hid_dev_irq(int irq, void *_shid)
struct spi_hid_input_header header;
int error = 0;
+ trace_spi_hid_dev_irq(shid, irq);
+ trace_spi_hid_header_transfer(shid);
+
scoped_guard(mutex, &shid->io_lock) {
error = spi_hid_input_sync(shid, shid->input->header,
sizeof(shid->input->header), true);
@@ -853,6 +806,13 @@ static irqreturn_t spi_hid_dev_irq(int irq, void *_shid)
goto out;
}
+ trace_spi_hid_input_header_complete(shid,
+ shid->input_transfer[0].tx_buf,
+ shid->input_transfer[0].len,
+ shid->input_transfer[1].rx_buf,
+ shid->input_transfer[1].len,
+ shid->input_message.status);
+
if (shid->input_message.status < 0) {
dev_warn(dev, "Error reading header: %d.",
shid->input_message.status);
@@ -889,6 +849,12 @@ static irqreturn_t spi_hid_dev_irq(int irq, void *_shid)
goto out;
}
+ trace_spi_hid_input_body_complete(shid, shid->input_transfer[0].tx_buf,
+ shid->input_transfer[0].len,
+ shid->input_transfer[1].rx_buf,
+ shid->input_transfer[1].len,
+ shid->input_message.status);
+
if (shid->input_message.status < 0) {
dev_warn(dev, "Error reading body: %d.",
shid->input_message.status);
diff --git a/drivers/hid/spi-hid/spi-hid-core.h b/drivers/hid/spi-hid/spi-hid-core.h
new file mode 100644
index 000000000000..293e2cfcfbf7
--- /dev/null
+++ b/drivers/hid/spi-hid/spi-hid-core.h
@@ -0,0 +1,91 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2021 Microsoft Corporation
+ * Copyright (c) 2026 Google LLC
+ */
+
+#ifndef SPI_HID_CORE_H
+#define SPI_HID_CORE_H
+
+#include <linux/hid-over-spi.h>
+#include <linux/spi/spi.h>
+
+/* Protocol message size constants */
+#define SPI_HID_READ_APPROVAL_LEN 5
+#define SPI_HID_OUTPUT_HEADER_LEN 8
+
+/* Raw input buffer with data from the bus */
+struct spi_hid_input_buf {
+ u8 header[HIDSPI_INPUT_HEADER_SIZE];
+ u8 body[HIDSPI_INPUT_BODY_HEADER_SIZE];
+ u8 content[];
+};
+
+/* Raw output report buffer to be put on the bus */
+struct spi_hid_output_buf {
+ u8 header[SPI_HID_OUTPUT_HEADER_LEN];
+ u8 content[];
+};
+
+/* Processed data from a device descriptor */
+struct spi_hid_device_descriptor {
+ u16 hid_version;
+ u16 report_descriptor_length;
+ u16 max_input_length;
+ u16 max_output_length;
+ u16 max_fragment_length;
+ u16 vendor_id;
+ u16 product_id;
+ u16 version_id;
+ u8 no_output_report_ack;
+};
+
+/* Driver context */
+struct spi_hid {
+ struct spi_device *spi; /* spi device. */
+ struct hid_device *hid; /* pointer to corresponding HID dev. */
+
+ struct spi_transfer input_transfer[2]; /* Transfer buffer for read and write. */
+ struct spi_message input_message; /* used to execute a sequence of spi transfers. */
+
+ struct spihid_ops *ops;
+ struct spi_hid_conf *conf;
+
+ struct spi_hid_device_descriptor desc; /* HID device descriptor. */
+ struct spi_hid_output_buf *output; /* Output buffer. */
+ struct spi_hid_input_buf *input; /* Input buffer. */
+ struct spi_hid_input_buf *response; /* Response buffer. */
+
+ u16 response_length;
+ u16 bufsize;
+
+ enum hidspi_power_state power_state;
+
+ u8 reset_attempts; /* The number of reset attempts. */
+
+ unsigned long flags; /* device flags. */
+
+ struct work_struct reset_work;
+
+ /* Control lock to ensure complete output transaction. */
+ struct mutex output_lock;
+ /* Power lock to make sure one power state change at a time. */
+ struct mutex power_lock;
+ /* I/O lock to prevent concurrent output writes during the input read. */
+ struct mutex io_lock;
+
+ struct completion output_done;
+
+ u8 read_approval_header[SPI_HID_READ_APPROVAL_LEN];
+ u8 read_approval_body[SPI_HID_READ_APPROVAL_LEN];
+
+ u32 report_descriptor_crc32; /* HID report descriptor crc32 checksum. */
+
+ u32 regulator_error_count;
+ int regulator_last_error;
+ u32 bus_error_count;
+ int bus_last_error;
+ u32 dir_count; /* device initiated reset count. */
+};
+
+#endif /* SPI_HID_CORE_H */
diff --git a/drivers/hid/spi-hid/spi-hid-trace.h b/drivers/hid/spi-hid/spi-hid-trace.h
new file mode 100644
index 000000000000..cc13d71a14de
--- /dev/null
+++ b/drivers/hid/spi-hid/spi-hid-trace.h
@@ -0,0 +1,169 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2021 Microsoft Corporation
+ */
+
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM spi_hid
+
+#if !defined(_SPI_HID_TRACE_H) || defined(TRACE_HEADER_MULTI_READ)
+#define _SPI_HID_TRACE_H
+
+#include <linux/types.h>
+#include <linux/tracepoint.h>
+#include "spi-hid-core.h"
+
+DECLARE_EVENT_CLASS(spi_hid_transfer,
+ TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
+ const void *rx_buf, u16 rx_len, int ret),
+
+ TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret),
+
+ TP_STRUCT__entry(
+ __field(int, bus_num)
+ __field(int, chip_select)
+ __field(int, ret)
+ __dynamic_array(u8, rx_buf, rx_len)
+ __dynamic_array(u8, tx_buf, tx_len)
+ ),
+
+ TP_fast_assign(
+ __entry->bus_num = shid->spi->controller->bus_num;
+ __entry->chip_select = shid->spi->chip_select;
+ __entry->ret = ret;
+
+ memcpy(__get_dynamic_array(tx_buf), tx_buf, tx_len);
+ memcpy(__get_dynamic_array(rx_buf), rx_buf, rx_len);
+ ),
+
+ TP_printk("spi%d.%d: len=%d tx=[%*phD] rx=[%*phD] --> %d",
+ __entry->bus_num, __entry->chip_select,
+ __get_dynamic_array_len(tx_buf) + __get_dynamic_array_len(rx_buf),
+ __get_dynamic_array_len(tx_buf), __get_dynamic_array(tx_buf),
+ __get_dynamic_array_len(rx_buf), __get_dynamic_array(rx_buf),
+ __entry->ret)
+);
+
+DEFINE_EVENT(spi_hid_transfer, spi_hid_input_sync,
+ TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
+ const void *rx_buf, u16 rx_len, int ret),
+ TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret));
+
+DEFINE_EVENT(spi_hid_transfer, spi_hid_input_header_complete,
+ TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
+ const void *rx_buf, u16 rx_len, int ret),
+ TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret));
+
+DEFINE_EVENT(spi_hid_transfer, spi_hid_input_body_complete,
+ TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
+ const void *rx_buf, u16 rx_len, int ret),
+ TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret));
+
+DECLARE_EVENT_CLASS(spi_hid_irq,
+ TP_PROTO(struct spi_hid *shid, int irq),
+
+ TP_ARGS(shid, irq),
+
+ TP_STRUCT__entry(
+ __field(int, bus_num)
+ __field(int, chip_select)
+ __field(int, irq)
+ ),
+
+ TP_fast_assign(
+ __entry->bus_num = shid->spi->controller->bus_num;
+ __entry->chip_select = shid->spi->chip_select;
+ __entry->irq = irq;
+ ),
+
+ TP_printk("spi%d.%d: IRQ %d",
+ __entry->bus_num, __entry->chip_select, __entry->irq)
+);
+
+DEFINE_EVENT(spi_hid_irq, spi_hid_dev_irq,
+ TP_PROTO(struct spi_hid *shid, int irq), TP_ARGS(shid, irq));
+
+DECLARE_EVENT_CLASS(spi_hid,
+ TP_PROTO(struct spi_hid *shid),
+
+ TP_ARGS(shid),
+
+ TP_STRUCT__entry(
+ __field(int, bus_num)
+ __field(int, chip_select)
+ __field(int, power_state)
+ __field(u32, flags)
+
+ __field(int, vendor_id)
+ __field(int, product_id)
+ __field(int, max_input_length)
+ __field(int, max_output_length)
+ __field(u16, hid_version)
+ __field(u16, report_descriptor_length)
+ __field(u16, version_id)
+ ),
+
+ TP_fast_assign(
+ __entry->bus_num = shid->spi->controller->bus_num;
+ __entry->chip_select = shid->spi->chip_select;
+ __entry->power_state = shid->power_state;
+ __entry->flags = shid->flags;
+
+ __entry->vendor_id = shid->desc.vendor_id;
+ __entry->product_id = shid->desc.product_id;
+ __entry->max_input_length = shid->desc.max_input_length;
+ __entry->max_output_length = shid->desc.max_output_length;
+ __entry->hid_version = shid->desc.hid_version;
+ __entry->report_descriptor_length =
+ shid->desc.report_descriptor_length;
+ __entry->version_id = shid->desc.version_id;
+ ),
+
+ TP_printk("spi%d.%d: (%04x:%04x v%d) HID v%d.%d state p:%d len i:%d o:%d r:%d flags 0x%08x",
+ __entry->bus_num, __entry->chip_select,
+ __entry->vendor_id, __entry->product_id, __entry->version_id,
+ __entry->hid_version >> 8, __entry->hid_version & 0xff,
+ __entry->power_state, __entry->max_input_length,
+ __entry->max_output_length, __entry->report_descriptor_length,
+ __entry->flags)
+);
+
+DEFINE_EVENT(spi_hid, spi_hid_header_transfer, TP_PROTO(struct spi_hid *shid),
+ TP_ARGS(shid));
+
+DEFINE_EVENT(spi_hid, spi_hid_process_input_report,
+ TP_PROTO(struct spi_hid *shid), TP_ARGS(shid));
+
+DEFINE_EVENT(spi_hid, spi_hid_input_report_handler,
+ TP_PROTO(struct spi_hid *shid), TP_ARGS(shid));
+
+DEFINE_EVENT(spi_hid, spi_hid_reset_response, TP_PROTO(struct spi_hid *shid),
+ TP_ARGS(shid));
+
+DEFINE_EVENT(spi_hid, spi_hid_create_device, TP_PROTO(struct spi_hid *shid),
+ TP_ARGS(shid));
+
+DEFINE_EVENT(spi_hid, spi_hid_refresh_device, TP_PROTO(struct spi_hid *shid),
+ TP_ARGS(shid));
+
+DEFINE_EVENT(spi_hid, spi_hid_response_handler, TP_PROTO(struct spi_hid *shid),
+ TP_ARGS(shid));
+
+DEFINE_EVENT(spi_hid, spi_hid_error_handler, TP_PROTO(struct spi_hid *shid),
+ TP_ARGS(shid));
+
+#endif /* _SPI_HID_TRACE_H */
+
+/*
+ * The following must be outside the protection of the above #if block.
+ */
+#undef TRACE_INCLUDE_PATH
+#undef TRACE_INCLUDE_FILE
+#define TRACE_INCLUDE_PATH .
+
+/*
+ * It is required that the TRACE_INCLUDE_FILE be the same
+ * as this file without the ".h".
+ */
+#define TRACE_INCLUDE_FILE spi-hid-trace
+#include <trace/define_trace.h>
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 07/11] HID: spi_hid: add ACPI support for SPI over HID
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
` (5 preceding siblings ...)
2026-04-02 1:59 ` [PATCH v3 06/11] HID: spi_hid: add spi_hid traces Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 08/11] HID: spi_hid: add device tree " Jingyuan Liang
` (3 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang,
Angela Czubak
From: Angela Czubak <acz@semihalf.com>
Detect SPI HID devices described in ACPI.
Signed-off-by: Angela Czubak <acz@semihalf.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
drivers/hid/spi-hid/Kconfig | 15 +++
drivers/hid/spi-hid/Makefile | 1 +
drivers/hid/spi-hid/spi-hid-acpi.c | 253 +++++++++++++++++++++++++++++++++++++
drivers/hid/spi-hid/spi-hid-core.c | 26 +---
drivers/hid/spi-hid/spi-hid.h | 45 +++++++
5 files changed, 315 insertions(+), 25 deletions(-)
diff --git a/drivers/hid/spi-hid/Kconfig b/drivers/hid/spi-hid/Kconfig
index 836fdefe8345..114b1e00da39 100644
--- a/drivers/hid/spi-hid/Kconfig
+++ b/drivers/hid/spi-hid/Kconfig
@@ -10,6 +10,21 @@ menuconfig SPI_HID
if SPI_HID
+config SPI_HID_ACPI
+ tristate "HID over SPI transport layer ACPI driver"
+ depends on ACPI
+ select SPI_HID_CORE
+ help
+ Say Y here if you use a keyboard, a touchpad, a touchscreen, or any
+ other HID based devices which are connected to your computer via SPI.
+ This driver supports ACPI-based systems.
+
+ If unsure, say N.
+
+ This support is also available as a module. If so, the module
+ will be called spi-hid-acpi. It will also build/depend on the
+ module spi-hid.
+
config SPI_HID_CORE
tristate
endif
diff --git a/drivers/hid/spi-hid/Makefile b/drivers/hid/spi-hid/Makefile
index 733e006df56e..3ca326602643 100644
--- a/drivers/hid/spi-hid/Makefile
+++ b/drivers/hid/spi-hid/Makefile
@@ -8,3 +8,4 @@
obj-$(CONFIG_SPI_HID_CORE) += spi-hid.o
spi-hid-objs = spi-hid-core.o
CFLAGS_spi-hid-core.o := -I$(src)
+obj-$(CONFIG_SPI_HID_ACPI) += spi-hid-acpi.o
diff --git a/drivers/hid/spi-hid/spi-hid-acpi.c b/drivers/hid/spi-hid/spi-hid-acpi.c
new file mode 100644
index 000000000000..298e3ba44d8a
--- /dev/null
+++ b/drivers/hid/spi-hid/spi-hid-acpi.c
@@ -0,0 +1,253 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * HID over SPI protocol, ACPI related code
+ *
+ * Copyright (c) 2021 Microsoft Corporation
+ * Copyright (c) 2026 Google LLC
+ *
+ * This code was forked out of the HID over SPI core code, which is partially
+ * based on "HID over I2C protocol implementation:
+ *
+ * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@gmail.com>
+ * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France
+ * Copyright (c) 2012 Red Hat, Inc
+ *
+ * which in turn is partially based on "USB HID support for Linux":
+ *
+ * Copyright (c) 1999 Andreas Gal
+ * Copyright (c) 2000-2005 Vojtech Pavlik <vojtech@suse.cz>
+ * Copyright (c) 2005 Michael Haboustak <mike-@cinci.rr.com> for Concept2, Inc
+ * Copyright (c) 2007-2008 Oliver Neukum
+ * Copyright (c) 2006-2010 Jiri Kosina
+ */
+
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/reset.h>
+#include <linux/uuid.h>
+
+#include "spi-hid.h"
+
+/* Config structure is filled with data from ACPI */
+struct spi_hid_acpi_config {
+ struct spihid_ops ops;
+
+ struct spi_hid_conf property_conf;
+ u32 post_power_on_delay_ms;
+ u32 minimal_reset_delay_ms;
+ struct acpi_device *adev;
+};
+
+/* HID SPI Device: 6e2ac436-0fcf41af-a265-b32a220dcfab */
+static guid_t spi_hid_guid =
+ GUID_INIT(0x6E2AC436, 0x0FCF, 0x41AF,
+ 0xA2, 0x65, 0xB3, 0x2A, 0x22, 0x0D, 0xCF, 0xAB);
+
+static int spi_hid_acpi_populate_config(struct spi_hid_acpi_config *conf,
+ struct acpi_device *adev)
+{
+ acpi_handle handle = acpi_device_handle(adev);
+ union acpi_object *obj;
+
+ conf->adev = adev;
+
+ /* Revision 3 for HID over SPI V1, see specification. */
+ obj = acpi_evaluate_dsm_typed(handle, &spi_hid_guid, 3, 1, NULL,
+ ACPI_TYPE_INTEGER);
+ if (!obj) {
+ acpi_handle_err(handle,
+ "Error _DSM call to get HID input report header address failed");
+ return -ENODEV;
+ }
+ conf->property_conf.input_report_header_address = obj->integer.value;
+ ACPI_FREE(obj);
+
+ obj = acpi_evaluate_dsm_typed(handle, &spi_hid_guid, 3, 2, NULL,
+ ACPI_TYPE_INTEGER);
+ if (!obj) {
+ acpi_handle_err(handle,
+ "Error _DSM call to get HID input report body address failed");
+ return -ENODEV;
+ }
+ conf->property_conf.input_report_body_address = obj->integer.value;
+ ACPI_FREE(obj);
+
+ obj = acpi_evaluate_dsm_typed(handle, &spi_hid_guid, 3, 3, NULL,
+ ACPI_TYPE_INTEGER);
+ if (!obj) {
+ acpi_handle_err(handle,
+ "Error _DSM call to get HID output report header address failed");
+ return -ENODEV;
+ }
+ conf->property_conf.output_report_address = obj->integer.value;
+ ACPI_FREE(obj);
+
+ obj = acpi_evaluate_dsm_typed(handle, &spi_hid_guid, 3, 4, NULL,
+ ACPI_TYPE_BUFFER);
+ if (!obj) {
+ acpi_handle_err(handle,
+ "Error _DSM call to get HID read opcode failed");
+ return -ENODEV;
+ }
+ if (obj->buffer.length == 1) {
+ conf->property_conf.read_opcode = obj->buffer.pointer[0];
+ } else {
+ acpi_handle_err(handle,
+ "Error _DSM call to get HID read opcode, too long buffer");
+ ACPI_FREE(obj);
+ return -ENODEV;
+ }
+ ACPI_FREE(obj);
+
+ obj = acpi_evaluate_dsm_typed(handle, &spi_hid_guid, 3, 5, NULL,
+ ACPI_TYPE_BUFFER);
+ if (!obj) {
+ acpi_handle_err(handle,
+ "Error _DSM call to get HID write opcode failed");
+ return -ENODEV;
+ }
+ if (obj->buffer.length == 1) {
+ conf->property_conf.write_opcode = obj->buffer.pointer[0];
+ } else {
+ acpi_handle_err(handle,
+ "Error _DSM call to get HID write opcode, too long buffer");
+ ACPI_FREE(obj);
+ return -ENODEV;
+ }
+ ACPI_FREE(obj);
+
+ /* Value not provided in ACPI,*/
+ conf->post_power_on_delay_ms = 5;
+ conf->minimal_reset_delay_ms = 150;
+
+ if (!acpi_has_method(handle, "_RST")) {
+ acpi_handle_err(handle, "No reset method for acpi handle");
+ return -EINVAL;
+ }
+
+ /* FIXME: not reading hid-over-spi-flags, multi-SPI not supported */
+
+ return 0;
+}
+
+static int spi_hid_acpi_power_none(struct spihid_ops *ops)
+{
+ return 0;
+}
+
+static int spi_hid_acpi_power_down(struct spihid_ops *ops)
+{
+ struct spi_hid_acpi_config *conf = container_of(ops,
+ struct spi_hid_acpi_config,
+ ops);
+
+ return acpi_device_set_power(conf->adev, ACPI_STATE_D3);
+}
+
+static int spi_hid_acpi_power_up(struct spihid_ops *ops)
+{
+ struct spi_hid_acpi_config *conf = container_of(ops,
+ struct spi_hid_acpi_config,
+ ops);
+ int error;
+
+ error = acpi_device_set_power(conf->adev, ACPI_STATE_D0);
+ if (error) {
+ dev_err(&conf->adev->dev, "Error could not power up ACPI device: %d.", error);
+ return error;
+ }
+
+ if (conf->post_power_on_delay_ms)
+ msleep(conf->post_power_on_delay_ms);
+
+ return 0;
+}
+
+static int spi_hid_acpi_assert_reset(struct spihid_ops *ops)
+{
+ return 0;
+}
+
+static int spi_hid_acpi_deassert_reset(struct spihid_ops *ops)
+{
+ struct spi_hid_acpi_config *conf = container_of(ops,
+ struct spi_hid_acpi_config,
+ ops);
+
+ return device_reset(&conf->adev->dev);
+}
+
+static void spi_hid_acpi_sleep_minimal_reset_delay(struct spihid_ops *ops)
+{
+ struct spi_hid_acpi_config *conf = container_of(ops,
+ struct spi_hid_acpi_config,
+ ops);
+ fsleep(1000 * conf->minimal_reset_delay_ms);
+}
+
+static int spi_hid_acpi_probe(struct spi_device *spi)
+{
+ struct device *dev = &spi->dev;
+ struct acpi_device *adev;
+ struct spi_hid_acpi_config *config;
+ int error;
+
+ adev = ACPI_COMPANION(dev);
+ if (!adev) {
+ dev_err(dev, "Error could not get ACPI device.");
+ return -ENODEV;
+ }
+
+ config = devm_kzalloc(dev, sizeof(struct spi_hid_acpi_config),
+ GFP_KERNEL);
+ if (!config)
+ return -ENOMEM;
+
+ if (acpi_device_power_manageable(adev)) {
+ config->ops.power_up = spi_hid_acpi_power_up;
+ config->ops.power_down = spi_hid_acpi_power_down;
+ } else {
+ config->ops.power_up = spi_hid_acpi_power_none;
+ config->ops.power_down = spi_hid_acpi_power_none;
+ }
+ config->ops.assert_reset = spi_hid_acpi_assert_reset;
+ config->ops.deassert_reset = spi_hid_acpi_deassert_reset;
+ config->ops.sleep_minimal_reset_delay =
+ spi_hid_acpi_sleep_minimal_reset_delay;
+
+ error = spi_hid_acpi_populate_config(config, adev);
+ if (error) {
+ dev_err(dev, "%s: unable to populate config data.", __func__);
+ return error;
+ }
+
+ return spi_hid_core_probe(spi, &config->ops, &config->property_conf);
+}
+
+static const struct acpi_device_id spi_hid_acpi_match[] = {
+ { "ACPI0C51", 0 },
+ { "PNP0C51", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, spi_hid_acpi_match);
+
+static struct spi_driver spi_hid_acpi_driver = {
+ .driver = {
+ .name = "spi_hid_acpi",
+ .owner = THIS_MODULE,
+ .acpi_match_table = spi_hid_acpi_match,
+ .probe_type = PROBE_PREFER_ASYNCHRONOUS,
+ .dev_groups = spi_hid_groups,
+ },
+ .probe = spi_hid_acpi_probe,
+ .remove = spi_hid_core_remove,
+};
+
+module_spi_driver(spi_hid_acpi_driver);
+
+MODULE_DESCRIPTION("HID over SPI ACPI transport driver");
+MODULE_AUTHOR("Angela Czubak <aczubak@google.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/hid/spi-hid/spi-hid-core.c b/drivers/hid/spi-hid/spi-hid-core.c
index 802615565541..d48175c764b9 100644
--- a/drivers/hid/spi-hid/spi-hid-core.c
+++ b/drivers/hid/spi-hid/spi-hid-core.c
@@ -43,6 +43,7 @@
#include <linux/wait.h>
#include <linux/workqueue.h>
+#include "spi-hid.h"
#include "spi-hid-core.h"
#define CREATE_TRACE_POINTS
@@ -110,31 +111,6 @@ struct spi_hid_output_report {
u8 *content;
};
-/* struct spi_hid_conf - Conf provided to the core */
-struct spi_hid_conf {
- u32 input_report_header_address;
- u32 input_report_body_address;
- u32 output_report_address;
- u8 read_opcode;
- u8 write_opcode;
-};
-
-/**
- * struct spihid_ops - Ops provided to the core
- * @power_up: do sequencing to power up the device
- * @power_down: do sequencing to power down the device
- * @assert_reset: do sequencing to assert the reset line
- * @deassert_reset: do sequencing to deassert the reset line
- * @sleep_minimal_reset_delay: minimal sleep delay during reset
- */
-struct spihid_ops {
- int (*power_up)(struct spihid_ops *ops);
- int (*power_down)(struct spihid_ops *ops);
- int (*assert_reset)(struct spihid_ops *ops);
- int (*deassert_reset)(struct spihid_ops *ops);
- void (*sleep_minimal_reset_delay)(struct spihid_ops *ops);
-};
-
static struct hid_ll_driver spi_hid_ll_driver;
static void spi_hid_populate_read_approvals(const struct spi_hid_conf *conf,
diff --git a/drivers/hid/spi-hid/spi-hid.h b/drivers/hid/spi-hid/spi-hid.h
new file mode 100644
index 000000000000..f5a5f4d54beb
--- /dev/null
+++ b/drivers/hid/spi-hid/spi-hid.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2021 Microsoft Corporation
+ * Copyright (c) 2026 Google LLC
+ */
+
+#ifndef SPI_HID_H
+#define SPI_HID_H
+
+#include <linux/spi/spi.h>
+#include <linux/sysfs.h>
+
+/* struct spi_hid_conf - Conf provided to the core */
+struct spi_hid_conf {
+ u32 input_report_header_address;
+ u32 input_report_body_address;
+ u32 output_report_address;
+ u8 read_opcode;
+ u8 write_opcode;
+};
+
+/**
+ * struct spihid_ops - Ops provided to the core
+ * @power_up: do sequencing to power up the device
+ * @power_down: do sequencing to power down the device
+ * @assert_reset: do sequencing to assert the reset line
+ * @deassert_reset: do sequencing to deassert the reset line
+ * @sleep_minimal_reset_delay: minimal sleep delay during reset
+ */
+struct spihid_ops {
+ int (*power_up)(struct spihid_ops *ops);
+ int (*power_down)(struct spihid_ops *ops);
+ int (*assert_reset)(struct spihid_ops *ops);
+ int (*deassert_reset)(struct spihid_ops *ops);
+ void (*sleep_minimal_reset_delay)(struct spihid_ops *ops);
+};
+
+int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
+ struct spi_hid_conf *conf);
+
+void spi_hid_core_remove(struct spi_device *spi);
+
+extern const struct attribute_group *spi_hid_groups[];
+
+#endif /* SPI_HID_H */
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 08/11] HID: spi_hid: add device tree support for SPI over HID
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
` (6 preceding siblings ...)
2026-04-02 1:59 ` [PATCH v3 07/11] HID: spi_hid: add ACPI support for SPI over HID Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 09/11] dt-bindings: input: Document hid-over-spi DT schema Jingyuan Liang
` (2 subsequent siblings)
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang,
Jarrett Schultz, Dmitry Antipov
From: Jarrett Schultz <jaschultz@microsoft.com>
Signed-off-by: Dmitry Antipov <dmanti@microsoft.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
drivers/hid/spi-hid/Kconfig | 15 +++
drivers/hid/spi-hid/Makefile | 1 +
drivers/hid/spi-hid/spi-hid-of.c | 243 +++++++++++++++++++++++++++++++++++++++
3 files changed, 259 insertions(+)
diff --git a/drivers/hid/spi-hid/Kconfig b/drivers/hid/spi-hid/Kconfig
index 114b1e00da39..76a2cd587a3e 100644
--- a/drivers/hid/spi-hid/Kconfig
+++ b/drivers/hid/spi-hid/Kconfig
@@ -25,6 +25,21 @@ config SPI_HID_ACPI
will be called spi-hid-acpi. It will also build/depend on the
module spi-hid.
+config SPI_HID_OF
+ tristate "HID over SPI transport layer Open Firmware driver"
+ depends on OF
+ select SPI_HID_CORE
+ help
+ Say Y here if you use a keyboard, a touchpad, a touchscreen, or any
+ other HID based devices which are connected to your computer via SPI.
+ This driver supports Open Firmware (Device Tree)-based systems.
+
+ If unsure, say N.
+
+ This support is also available as a module. If so, the module
+ will be called spi-hid-of. It will also build/depend on the
+ module spi-hid.
+
config SPI_HID_CORE
tristate
endif
diff --git a/drivers/hid/spi-hid/Makefile b/drivers/hid/spi-hid/Makefile
index 3ca326602643..31192e71edae 100644
--- a/drivers/hid/spi-hid/Makefile
+++ b/drivers/hid/spi-hid/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_SPI_HID_CORE) += spi-hid.o
spi-hid-objs = spi-hid-core.o
CFLAGS_spi-hid-core.o := -I$(src)
obj-$(CONFIG_SPI_HID_ACPI) += spi-hid-acpi.o
+obj-$(CONFIG_SPI_HID_OF) += spi-hid-of.o
diff --git a/drivers/hid/spi-hid/spi-hid-of.c b/drivers/hid/spi-hid/spi-hid-of.c
new file mode 100644
index 000000000000..651456b6906d
--- /dev/null
+++ b/drivers/hid/spi-hid/spi-hid-of.c
@@ -0,0 +1,243 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * HID over SPI protocol, Open Firmware related code
+ *
+ * Copyright (c) 2021 Microsoft Corporation
+ *
+ * This code was forked out of the HID over SPI core code, which is partially
+ * based on "HID over I2C protocol implementation:
+ *
+ * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@gmail.com>
+ * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France
+ * Copyright (c) 2012 Red Hat, Inc
+ *
+ * which in turn is partially based on "USB HID support for Linux":
+ *
+ * Copyright (c) 1999 Andreas Gal
+ * Copyright (c) 2000-2005 Vojtech Pavlik <vojtech@suse.cz>
+ * Copyright (c) 2005 Michael Haboustak <mike-@cinci.rr.com> for Concept2, Inc
+ * Copyright (c) 2007-2008 Oliver Neukum
+ * Copyright (c) 2006-2010 Jiri Kosina
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regulator/consumer.h>
+#include <linux/gpio/consumer.h>
+#include <linux/delay.h>
+
+#include "spi-hid.h"
+
+struct spi_hid_timing_data {
+ u32 post_power_on_delay_ms;
+ u32 minimal_reset_delay_ms;
+};
+
+/* Config structure is filled with data from Device Tree */
+struct spi_hid_of_config {
+ struct spihid_ops ops;
+
+ struct spi_hid_conf property_conf;
+ const struct spi_hid_timing_data *timing_data;
+
+ struct gpio_desc *reset_gpio;
+ struct regulator *supply;
+ bool supply_enabled;
+ u16 hid_over_spi_flags;
+};
+
+static int spi_hid_of_populate_config(struct spi_hid_of_config *conf,
+ struct device *dev)
+{
+ int error;
+ u32 val;
+
+ error = device_property_read_u32(dev, "input-report-header-address",
+ &val);
+ if (error) {
+ dev_err(dev, "Input report header address not provided.");
+ return -ENODEV;
+ }
+ conf->property_conf.input_report_header_address = val;
+
+ error = device_property_read_u32(dev, "input-report-body-address", &val);
+ if (error) {
+ dev_err(dev, "Input report body address not provided.");
+ return -ENODEV;
+ }
+ conf->property_conf.input_report_body_address = val;
+
+ error = device_property_read_u32(dev, "output-report-address", &val);
+ if (error) {
+ dev_err(dev, "Output report address not provided.");
+ return -ENODEV;
+ }
+ conf->property_conf.output_report_address = val;
+
+ error = device_property_read_u32(dev, "read-opcode", &val);
+ if (error) {
+ dev_err(dev, "Read opcode not provided.");
+ return -ENODEV;
+ }
+ conf->property_conf.read_opcode = val;
+
+ error = device_property_read_u32(dev, "write-opcode", &val);
+ if (error) {
+ dev_err(dev, "Write opcode not provided.");
+ return -ENODEV;
+ }
+ conf->property_conf.write_opcode = val;
+
+ conf->supply = devm_regulator_get(dev, "vdd");
+ if (IS_ERR(conf->supply)) {
+ if (PTR_ERR(conf->supply) != -EPROBE_DEFER)
+ dev_err(dev, "Failed to get regulator: %ld.",
+ PTR_ERR(conf->supply));
+ return PTR_ERR(conf->supply);
+ }
+ conf->supply_enabled = false;
+
+ conf->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(conf->reset_gpio)) {
+ dev_err(dev, "%s: error getting reset GPIO.", __func__);
+ return PTR_ERR(conf->reset_gpio);
+ }
+
+ return 0;
+}
+
+static int spi_hid_of_power_down(struct spihid_ops *ops)
+{
+ struct spi_hid_of_config *conf = container_of(ops,
+ struct spi_hid_of_config,
+ ops);
+ int error;
+
+ if (!conf->supply_enabled)
+ return 0;
+
+ error = regulator_disable(conf->supply);
+ if (error == 0)
+ conf->supply_enabled = false;
+
+ return error;
+}
+
+static int spi_hid_of_power_up(struct spihid_ops *ops)
+{
+ struct spi_hid_of_config *conf = container_of(ops,
+ struct spi_hid_of_config,
+ ops);
+ int error;
+
+ if (conf->supply_enabled)
+ return 0;
+
+ error = regulator_enable(conf->supply);
+
+ if (error == 0) {
+ conf->supply_enabled = true;
+ fsleep(1000 * conf->timing_data->post_power_on_delay_ms);
+ }
+
+ return error;
+}
+
+static int spi_hid_of_assert_reset(struct spihid_ops *ops)
+{
+ struct spi_hid_of_config *conf = container_of(ops,
+ struct spi_hid_of_config,
+ ops);
+
+ gpiod_set_value(conf->reset_gpio, 1);
+ return 0;
+}
+
+static int spi_hid_of_deassert_reset(struct spihid_ops *ops)
+{
+ struct spi_hid_of_config *conf = container_of(ops,
+ struct spi_hid_of_config,
+ ops);
+
+ gpiod_set_value(conf->reset_gpio, 0);
+ return 0;
+}
+
+static void spi_hid_of_sleep_minimal_reset_delay(struct spihid_ops *ops)
+{
+ struct spi_hid_of_config *conf = container_of(ops,
+ struct spi_hid_of_config,
+ ops);
+ fsleep(1000 * conf->timing_data->minimal_reset_delay_ms);
+}
+
+static int spi_hid_of_probe(struct spi_device *spi)
+{
+ struct device *dev = &spi->dev;
+ struct spi_hid_of_config *config;
+ int error;
+
+ config = devm_kzalloc(dev, sizeof(struct spi_hid_of_config),
+ GFP_KERNEL);
+ if (!config)
+ return -ENOMEM;
+
+ config->ops.power_up = spi_hid_of_power_up;
+ config->ops.power_down = spi_hid_of_power_down;
+ config->ops.assert_reset = spi_hid_of_assert_reset;
+ config->ops.deassert_reset = spi_hid_of_deassert_reset;
+ config->ops.sleep_minimal_reset_delay =
+ spi_hid_of_sleep_minimal_reset_delay;
+
+ config->timing_data = device_get_match_data(dev);
+ /*
+ * FIXME: hid_over_spi_flags could be retrieved from spi mode.
+ * It is always 0 because multi-SPI not supported.
+ */
+ config->hid_over_spi_flags = 0;
+
+ error = spi_hid_of_populate_config(config, dev);
+ if (error) {
+ dev_err(dev, "%s: unable to populate config data.", __func__);
+ return error;
+ }
+
+ return spi_hid_core_probe(spi, &config->ops, &config->property_conf);
+}
+
+const struct spi_hid_timing_data timing_data = {
+ .post_power_on_delay_ms = 10,
+ .minimal_reset_delay_ms = 100,
+};
+
+const struct of_device_id spi_hid_of_match[] = {
+ { .compatible = "hid-over-spi", .data = &timing_data },
+ {}
+};
+MODULE_DEVICE_TABLE(of, spi_hid_of_match);
+
+static const struct spi_device_id spi_hid_of_id_table[] = {
+ { "hid", 0 },
+ { "hid-over-spi", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(spi, spi_hid_of_id_table);
+
+static struct spi_driver spi_hid_of_driver = {
+ .driver = {
+ .name = "spi_hid_of",
+ .owner = THIS_MODULE,
+ .of_match_table = spi_hid_of_match,
+ .probe_type = PROBE_PREFER_ASYNCHRONOUS,
+ .dev_groups = spi_hid_groups,
+ },
+ .probe = spi_hid_of_probe,
+ .remove = spi_hid_core_remove,
+ .id_table = spi_hid_of_id_table,
+};
+
+module_spi_driver(spi_hid_of_driver);
+
+MODULE_DESCRIPTION("HID over SPI OF transport driver");
+MODULE_AUTHOR("Dmitry Antipov <dmanti@microsoft.com>");
+MODULE_LICENSE("GPL");
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 09/11] dt-bindings: input: Document hid-over-spi DT schema
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
` (7 preceding siblings ...)
2026-04-02 1:59 ` [PATCH v3 08/11] HID: spi_hid: add device tree " Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 10/11] HID: spi-hid: add power management implementation Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 11/11] HID: spi-hid: add panel follower support Jingyuan Liang
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang,
Dmitry Antipov, Jarrett Schultz
Documentation describes the required and optional properties for
implementing Device Tree for a Microsoft G6 Touch Digitizer that
supports HID over SPI Protocol 1.0 specification.
The properties are common to HID over SPI.
Signed-off-by: Dmitry Antipov <dmanti@microsoft.com>
Signed-off-by: Jarrett Schultz <jaschultz@microsoft.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
.../devicetree/bindings/input/hid-over-spi.yaml | 126 +++++++++++++++++++++
1 file changed, 126 insertions(+)
diff --git a/Documentation/devicetree/bindings/input/hid-over-spi.yaml b/Documentation/devicetree/bindings/input/hid-over-spi.yaml
new file mode 100644
index 000000000000..d1b0a2e26c32
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/hid-over-spi.yaml
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/hid-over-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HID over SPI Devices
+
+maintainers:
+ - Benjamin Tissoires <benjamin.tissoires@redhat.com>
+ - Jiri Kosina <jkosina@suse.cz>
+
+description: |+
+ HID over SPI provides support for various Human Interface Devices over the
+ SPI bus. These devices can be for example touchpads, keyboards, touch screens
+ or sensors.
+
+ The specification has been written by Microsoft and is currently available
+ here: https://www.microsoft.com/en-us/download/details.aspx?id=103325
+
+ If this binding is used, the kernel module spi-hid will handle the
+ communication with the device and the generic hid core layer will handle the
+ protocol.
+
+allOf:
+ - $ref: /schemas/input/touchscreen/touchscreen.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - microsoft,g6-touch-digitizer
+ - const: hid-over-spi
+ - description: Just "hid-over-spi" alone is allowed, but not recommended.
+ const: hid-over-spi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ reset-gpios:
+ maxItems: 1
+ description:
+ GPIO specifier for the digitizer's reset pin (active low). The line must
+ be flagged with GPIO_ACTIVE_LOW.
+
+ vdd-supply:
+ description:
+ Regulator for the VDD supply voltage.
+
+ input-report-header-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 0xffffff
+ description:
+ A value to be included in the Read Approval packet, listing an address of
+ the input report header to be put on the SPI bus. This address has 24
+ bits.
+
+ input-report-body-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 0xffffff
+ description:
+ A value to be included in the Read Approval packet, listing an address of
+ the input report body to be put on the SPI bus. This address has 24 bits.
+
+ output-report-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 0xffffff
+ description:
+ A value to be included in the Output Report sent by the host, listing an
+ address where the output report on the SPI bus is to be written to. This
+ address has 24 bits.
+
+ read-opcode:
+ $ref: /schemas/types.yaml#/definitions/uint8
+ description:
+ Value to be used in Read Approval packets. 1 byte.
+
+ write-opcode:
+ $ref: /schemas/types.yaml#/definitions/uint8
+ description:
+ Value to be used in Write Approval packets. 1 byte.
+
+required:
+ - compatible
+ - interrupts
+ - reset-gpios
+ - vdd-supply
+ - input-report-header-address
+ - input-report-body-address
+ - output-report-address
+ - read-opcode
+ - write-opcode
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hid@0 {
+ compatible = "microsoft,g6-touch-digitizer", "hid-over-spi";
+ reg = <0x0>;
+ interrupts-extended = <&gpio 42 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&pm8350c_l3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_d6_int_bias>;
+ input-report-header-address = <0x1000>;
+ input-report-body-address = <0x1004>;
+ output-report-address = <0x2000>;
+ read-opcode = /bits/ 8 <0x0b>;
+ write-opcode = /bits/ 8 <0x02>;
+ };
+ };
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 10/11] HID: spi-hid: add power management implementation
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
` (8 preceding siblings ...)
2026-04-02 1:59 ` [PATCH v3 09/11] dt-bindings: input: Document hid-over-spi DT schema Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
2026-04-02 1:59 ` [PATCH v3 11/11] HID: spi-hid: add panel follower support Jingyuan Liang
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang
Implement HID over SPI driver power management callbacks.
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
drivers/hid/spi-hid/spi-hid-acpi.c | 1 +
drivers/hid/spi-hid/spi-hid-core.c | 107 +++++++++++++++++++++++++++++++++++++
drivers/hid/spi-hid/spi-hid-of.c | 1 +
drivers/hid/spi-hid/spi-hid.h | 1 +
4 files changed, 110 insertions(+)
diff --git a/drivers/hid/spi-hid/spi-hid-acpi.c b/drivers/hid/spi-hid/spi-hid-acpi.c
index 298e3ba44d8a..15cfc4e6cc2f 100644
--- a/drivers/hid/spi-hid/spi-hid-acpi.c
+++ b/drivers/hid/spi-hid/spi-hid-acpi.c
@@ -238,6 +238,7 @@ static struct spi_driver spi_hid_acpi_driver = {
.driver = {
.name = "spi_hid_acpi",
.owner = THIS_MODULE,
+ .pm = &spi_hid_core_pm,
.acpi_match_table = spi_hid_acpi_match,
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
.dev_groups = spi_hid_groups,
diff --git a/drivers/hid/spi-hid/spi-hid-core.c b/drivers/hid/spi-hid/spi-hid-core.c
index d48175c764b9..5f7a5bb692d9 100644
--- a/drivers/hid/spi-hid/spi-hid-core.c
+++ b/drivers/hid/spi-hid/spi-hid-core.c
@@ -35,6 +35,8 @@
#include <linux/list.h>
#include <linux/module.h>
#include <linux/mutex.h>
+#include <linux/pm.h>
+#include <linux/pm_wakeirq.h>
#include <linux/slab.h>
#include <linux/spi/spi.h>
#include <linux/string.h>
@@ -244,6 +246,81 @@ static const char *spi_hid_power_mode_string(enum hidspi_power_state power_state
}
}
+static void spi_hid_suspend(struct spi_hid *shid)
+{
+ int error;
+ struct device *dev = &shid->spi->dev;
+
+ guard(mutex)(&shid->power_lock);
+ if (shid->power_state == HIDSPI_OFF)
+ return;
+
+ if (shid->hid) {
+ error = hid_driver_suspend(shid->hid, PMSG_SUSPEND);
+ if (error) {
+ dev_err(dev, "%s failed to suspend hid driver: %d",
+ __func__, error);
+ return;
+ }
+ }
+
+ disable_irq(shid->spi->irq);
+
+ clear_bit(SPI_HID_READY, &shid->flags);
+
+ if (!device_may_wakeup(dev)) {
+ set_bit(SPI_HID_RESET_PENDING, &shid->flags);
+
+ shid->ops->assert_reset(shid->ops);
+
+ error = shid->ops->power_down(shid->ops);
+ if (error) {
+ dev_err(dev, "%s: could not power down.", __func__);
+ shid->regulator_error_count++;
+ shid->regulator_last_error = error;
+ return;
+ }
+
+ shid->power_state = HIDSPI_OFF;
+ }
+}
+
+static void spi_hid_resume(struct spi_hid *shid)
+{
+ int error;
+ struct device *dev = &shid->spi->dev;
+
+ guard(mutex)(&shid->power_lock);
+ if (shid->power_state == HIDSPI_ON)
+ return;
+
+ enable_irq(shid->spi->irq);
+
+ if (!device_may_wakeup(dev)) {
+ shid->ops->assert_reset(shid->ops);
+
+ shid->ops->sleep_minimal_reset_delay(shid->ops);
+
+ error = shid->ops->power_up(shid->ops);
+ if (error) {
+ dev_err(dev, "%s: could not power up.", __func__);
+ shid->regulator_error_count++;
+ shid->regulator_last_error = error;
+ return;
+ }
+ shid->power_state = HIDSPI_ON;
+
+ shid->ops->deassert_reset(shid->ops);
+ }
+
+ if (shid->hid) {
+ error = hid_driver_reset_resume(shid->hid);
+ if (error)
+ dev_err(dev, "%s: failed to reset resume hid driver: %d.",
+ __func__, error);
+ }
+}
+
static void spi_hid_stop_hid(struct spi_hid *shid)
{
struct hid_device *hid = shid->hid;
@@ -1200,6 +1277,13 @@ int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
dev_err(dev, "%s: unable to request threaded IRQ.", __func__);
return error;
}
+ if (device_may_wakeup(dev)) {
+ error = dev_pm_set_wake_irq(dev, spi->irq);
+ if (error) {
+ dev_err(dev, "%s: failed to set wake IRQ.", __func__);
+ return error;
+ }
+ }
error = shid->ops->power_up(shid->ops);
if (error) {
@@ -1231,6 +1315,29 @@ void spi_hid_core_remove(struct spi_device *spi)
}
EXPORT_SYMBOL_GPL(spi_hid_core_remove);
+static int spi_hid_core_pm_suspend(struct device *dev)
+{
+ struct spi_hid *shid = dev_get_drvdata(dev);
+
+ spi_hid_suspend(shid);
+
+ return 0;
+}
+
+static int spi_hid_core_pm_resume(struct device *dev)
+{
+ struct spi_hid *shid = dev_get_drvdata(dev);
+
+ spi_hid_resume(shid);
+
+ return 0;
+}
+
+const struct dev_pm_ops spi_hid_core_pm = {
+ SYSTEM_SLEEP_PM_OPS(spi_hid_core_pm_suspend, spi_hid_core_pm_resume)
+};
+EXPORT_SYMBOL_GPL(spi_hid_core_pm);
+
MODULE_DESCRIPTION("HID over SPI transport driver");
MODULE_AUTHOR("Dmitry Antipov <dmanti@microsoft.com>");
MODULE_LICENSE("GPL");
diff --git a/drivers/hid/spi-hid/spi-hid-of.c b/drivers/hid/spi-hid/spi-hid-of.c
index 651456b6906d..80c481b77149 100644
--- a/drivers/hid/spi-hid/spi-hid-of.c
+++ b/drivers/hid/spi-hid/spi-hid-of.c
@@ -227,6 +227,7 @@ static struct spi_driver spi_hid_of_driver = {
.driver = {
.name = "spi_hid_of",
.owner = THIS_MODULE,
+ .pm = &spi_hid_core_pm,
.of_match_table = spi_hid_of_match,
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
.dev_groups = spi_hid_groups,
diff --git a/drivers/hid/spi-hid/spi-hid.h b/drivers/hid/spi-hid/spi-hid.h
index f5a5f4d54beb..17b2fdf192ed 100644
--- a/drivers/hid/spi-hid/spi-hid.h
+++ b/drivers/hid/spi-hid/spi-hid.h
@@ -41,5 +41,6 @@ int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
void spi_hid_core_remove(struct spi_device *spi);
extern const struct attribute_group *spi_hid_groups[];
+extern const struct dev_pm_ops spi_hid_core_pm;
#endif /* SPI_HID_H */
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v3 11/11] HID: spi-hid: add panel follower support
2026-04-02 1:59 [PATCH v3 00/11] Add spi-hid transport driver Jingyuan Liang
` (9 preceding siblings ...)
2026-04-02 1:59 ` [PATCH v3 10/11] HID: spi-hid: add power management implementation Jingyuan Liang
@ 2026-04-02 1:59 ` Jingyuan Liang
10 siblings, 0 replies; 12+ messages in thread
From: Jingyuan Liang @ 2026-04-02 1:59 UTC (permalink / raw)
To: Jiri Kosina, Benjamin Tissoires, Jonathan Corbet, Mark Brown,
Steven Rostedt, Masami Hiramatsu, Mathieu Desnoyers,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-input, linux-doc, linux-kernel, linux-spi,
linux-trace-kernel, devicetree, hbarnor, tfiga, Jingyuan Liang
Add support to spi-hid to be a panel follower.
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
drivers/hid/spi-hid/spi-hid-core.c | 199 +++++++++++++++++++++++++++++--------
drivers/hid/spi-hid/spi-hid-core.h | 7 ++
2 files changed, 163 insertions(+), 43 deletions(-)
diff --git a/drivers/hid/spi-hid/spi-hid-core.c b/drivers/hid/spi-hid/spi-hid-core.c
index 5f7a5bb692d9..9eedd4f1cba7 100644
--- a/drivers/hid/spi-hid/spi-hid-core.c
+++ b/drivers/hid/spi-hid/spi-hid-core.c
@@ -246,21 +246,21 @@ static const char *spi_hid_power_mode_string(enum hidspi_power_state power_state
}
}
-static void spi_hid_suspend(struct spi_hid *shid)
+static int spi_hid_suspend(struct spi_hid *shid)
{
int error;
struct device *dev = &shid->spi->dev;
guard(mutex)(&shid->power_lock);
if (shid->power_state == HIDSPI_OFF)
- return;
+ return 0;
if (shid->hid) {
error = hid_driver_suspend(shid->hid, PMSG_SUSPEND);
if (error) {
dev_err(dev, "%s failed to suspend hid driver: %d",
__func__, error);
- return;
+ return error;
}
}
@@ -278,21 +278,22 @@ static void spi_hid_suspend(struct spi_hid *shid)
dev_err(dev, "%s: could not power down.", __func__);
shid->regulator_error_count++;
shid->regulator_last_error = error;
- return;
+ return error;
}
shid->power_state = HIDSPI_OFF;
}
+ return 0;
}
-static void spi_hid_resume(struct spi_hid *shid)
+static int spi_hid_resume(struct spi_hid *shid)
{
int error;
struct device *dev = &shid->spi->dev;
guard(mutex)(&shid->power_lock);
if (shid->power_state == HIDSPI_ON)
- return;
+ return 0;
enable_irq(shid->spi->irq);
@@ -306,7 +307,7 @@ static void spi_hid_resume(struct spi_hid *shid)
dev_err(dev, "%s: could not power up.", __func__);
shid->regulator_error_count++;
shid->regulator_last_error = error;
- return;
+ return error;
}
shid->power_state = HIDSPI_ON;
@@ -315,10 +316,13 @@ static void spi_hid_resume(struct spi_hid *shid)
if (shid->hid) {
error = hid_driver_reset_resume(shid->hid);
- if (error)
+ if (error) {
dev_err(dev, "%s: failed to reset resume hid driver: %d.",
__func__, error);
+ return error;
+ }
}
+ return 0;
}
static void spi_hid_stop_hid(struct spi_hid *shid)
@@ -1215,6 +1219,132 @@ const struct attribute_group *spi_hid_groups[] = {
};
EXPORT_SYMBOL_GPL(spi_hid_groups);
+/*
+ * At the end of probe we initialize the device:
+ * 0) assert reset, bias the interrupt line
+ * 1) sleep minimal reset delay
+ * 2) request IRQ
+ * 3) power up the device
+ * 4) deassert reset (high)
+ * After this we expect an IRQ with a reset response.
+ */
+static int spi_hid_dev_init(struct spi_hid *shid)
+{
+ struct spi_device *spi = shid->spi;
+ struct device *dev = &spi->dev;
+ int error;
+
+ shid->ops->assert_reset(shid->ops);
+
+ shid->ops->sleep_minimal_reset_delay(shid->ops);
+
+ error = devm_request_threaded_irq(dev, spi->irq, NULL, spi_hid_dev_irq,
+ IRQF_ONESHOT, dev_name(&spi->dev), shid);
+ if (error) {
+ dev_err(dev, "%s: unable to request threaded IRQ.", __func__);
+ return error;
+ }
+ if (device_may_wakeup(dev)) {
+ error = dev_pm_set_wake_irq(dev, spi->irq);
+ if (error) {
+ dev_err(dev, "%s: failed to set wake IRQ.", __func__);
+ return error;
+ }
+ }
+
+ error = shid->ops->power_up(shid->ops);
+ if (error) {
+ dev_err(dev, "%s: could not power up.", __func__);
+ shid->regulator_error_count++;
+ shid->regulator_last_error = error;
+ return error;
+ }
+
+ shid->ops->deassert_reset(shid->ops);
+
+ return 0;
+}
+
+static void spi_hid_panel_follower_work(struct work_struct *work)
+{
+ struct spi_hid *shid = container_of(work, struct spi_hid,
+ panel_follower_work);
+ int error;
+
+ if (!shid->desc.hid_version)
+ error = spi_hid_dev_init(shid);
+ else
+ error = spi_hid_resume(shid);
+ if (error)
+ dev_warn(&shid->spi->dev, "Power on failed: %d", error);
+ else
+ WRITE_ONCE(shid->panel_follower_work_finished, true);
+
+ /*
+ * The work APIs provide a number of memory ordering guarantees
+ * including one that says that memory writes before schedule_work()
+ * are always visible to the work function, but they don't appear to
+ * guarantee that a write that happened in the work is visible after
+ * cancel_work_sync(). We'll add a write memory barrier here to match
+ * with spi_hid_panel_unpreparing() to ensure that our write to
+ * panel_follower_work_finished is visible there.
+ */
+ smp_wmb();
+}
+
+static int spi_hid_panel_follower_resume(struct drm_panel_follower *follower)
+{
+ struct spi_hid *shid = container_of(follower, struct spi_hid, panel_follower);
+
+ /*
+ * Powering on a touchscreen can be a slow process. Queue the work to
+ * the system workqueue so we don't block the panel's power up.
+ */
+ WRITE_ONCE(shid->panel_follower_work_finished, false);
+ schedule_work(&shid->panel_follower_work);
+
+ return 0;
+}
+
+static int spi_hid_panel_follower_suspend(struct drm_panel_follower *follower)
+{
+ struct spi_hid *shid = container_of(follower, struct spi_hid, panel_follower);
+
+ cancel_work_sync(&shid->panel_follower_work);
+
+ /* Match with shid_core_panel_follower_work() */
+ smp_rmb();
+ if (!READ_ONCE(shid->panel_follower_work_finished))
+ return 0;
+
+ return spi_hid_suspend(shid);
+}
+
+static const struct drm_panel_follower_funcs
+ spi_hid_panel_follower_prepare_funcs = {
+ .panel_prepared = spi_hid_panel_follower_resume,
+ .panel_unpreparing = spi_hid_panel_follower_suspend,
+};
+
+static int spi_hid_register_panel_follower(struct spi_hid *shid)
+{
+ struct device *dev = &shid->spi->dev;
+
+ shid->panel_follower.funcs = &spi_hid_panel_follower_prepare_funcs;
+
+ /*
+ * If we're not in control of our own power up/power down then we can't
+ * do the logic to manage wakeups. Give a warning if a user thought
+ * that was possible then force the capability off.
+ */
+ if (device_can_wakeup(dev)) {
+ dev_warn(dev, "Can't wakeup if following panel\n");
+ device_set_wakeup_capable(dev, false);
+ }
+
+ return drm_panel_add_follower(dev, &shid->panel_follower);
+}
+
int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
struct spi_hid_conf *conf)
{
@@ -1234,6 +1364,7 @@ int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
shid->ops = ops;
shid->conf = conf;
set_bit(SPI_HID_RESET_PENDING, &shid->flags);
+ shid->is_panel_follower = drm_is_panel_follower(&spi->dev);
spi_set_drvdata(spi, shid);
@@ -1247,6 +1378,7 @@ int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
init_completion(&shid->output_done);
INIT_WORK(&shid->reset_work, spi_hid_reset_work);
+ INIT_WORK(&shid->panel_follower_work, spi_hid_panel_follower_work);
/*
* We need to allocate the buffer without knowing the maximum
@@ -1257,42 +1389,18 @@ int spi_hid_core_probe(struct spi_device *spi, struct spihid_ops *ops,
if (error)
return error;
- /*
- * At the end of probe we initialize the device:
- * 0) assert reset, bias the interrupt line
- * 1) sleep minimal reset delay
- * 2) request IRQ
- * 3) power up the device
- * 4) deassert reset (high)
- * After this we expect an IRQ with a reset response.
- */
-
- shid->ops->assert_reset(shid->ops);
-
- shid->ops->sleep_minimal_reset_delay(shid->ops);
-
- error = devm_request_threaded_irq(dev, spi->irq, NULL, spi_hid_dev_irq,
- IRQF_ONESHOT, dev_name(&spi->dev), shid);
- if (error) {
- dev_err(dev, "%s: unable to request threaded IRQ.", __func__);
- return error;
- }
- if (device_may_wakeup(dev)) {
- error = dev_pm_set_wake_irq(dev, spi->irq);
+ if (shid->is_panel_follower) {
+ error = spi_hid_register_panel_follower(shid);
if (error) {
- dev_err(dev, "%s: failed to set wake IRQ.", __func__);
+ dev_err(dev, "%s: could not add panel follower.", __func__);
return error;
}
+ } else {
+ error = spi_hid_dev_init(shid);
+ if (error)
+ return error;
}
- error = shid->ops->power_up(shid->ops);
- if (error) {
- dev_err(dev, "%s: could not power up.", __func__);
- return error;
- }
-
- shid->ops->deassert_reset(shid->ops);
-
dev_dbg(dev, "%s: d3 -> %s.", __func__,
spi_hid_power_mode_string(shid->power_state));
@@ -1306,6 +1414,9 @@ void spi_hid_core_remove(struct spi_device *spi)
struct device *dev = &spi->dev;
int error;
+ if (shid->is_panel_follower)
+ drm_panel_remove_follower(&shid->panel_follower);
+
spi_hid_stop_hid(shid);
shid->ops->assert_reset(shid->ops);
@@ -1319,18 +1430,20 @@ static int spi_hid_core_pm_suspend(struct device *dev)
{
struct spi_hid *shid = dev_get_drvdata(dev);
- spi_hid_suspend(shid);
+ if (shid->is_panel_follower)
+ return 0;
- return 0;
+ return spi_hid_suspend(shid);
}
static int spi_hid_core_pm_resume(struct device *dev)
{
struct spi_hid *shid = dev_get_drvdata(dev);
- spi_hid_resume(shid);
+ if (shid->is_panel_follower)
+ return 0;
- return 0;
+ return spi_hid_resume(shid);
}
const struct dev_pm_ops spi_hid_core_pm = {
diff --git a/drivers/hid/spi-hid/spi-hid-core.h b/drivers/hid/spi-hid/spi-hid-core.h
index 293e2cfcfbf7..261b2fd7f332 100644
--- a/drivers/hid/spi-hid/spi-hid-core.h
+++ b/drivers/hid/spi-hid/spi-hid-core.h
@@ -10,6 +10,8 @@
#include <linux/hid-over-spi.h>
#include <linux/spi/spi.h>
+#include <drm/drm_panel.h>
+
/* Protocol message size constants */
#define SPI_HID_READ_APPROVAL_LEN 5
#define SPI_HID_OUTPUT_HEADER_LEN 8
@@ -56,6 +58,10 @@ struct spi_hid {
struct spi_hid_input_buf *input; /* Input buffer. */
struct spi_hid_input_buf *response; /* Response buffer. */
+ struct drm_panel_follower panel_follower;
+ bool is_panel_follower;
+ bool panel_follower_work_finished;
+
u16 response_length;
u16 bufsize;
@@ -66,6 +72,7 @@ struct spi_hid {
unsigned long flags; /* device flags. */
struct work_struct reset_work;
+ struct work_struct panel_follower_work;
/* Control lock to ensure complete output transaction. */
struct mutex output_lock;
--
2.53.0.1185.g05d4b7b318-goog
^ permalink raw reply related [flat|nested] 12+ messages in thread