* [PATCH] OMAP3: RX-51: complete tsc2005 controller support
@ 2011-12-14 13:01 Vladimir Zapolskiy
2011-12-14 13:02 ` [PATCH v2] " Vladimir Zapolskiy
2011-12-14 15:45 ` [PATCH] " Aaro Koskinen
0 siblings, 2 replies; 6+ messages in thread
From: Vladimir Zapolskiy @ 2011-12-14 13:01 UTC (permalink / raw)
To: linux-omap, linux-input; +Cc: Dmitry Torokhov, Aaro Koskinen, Tony Lindgren
This change adds initialization of TSC2005 touchscreen controller found on Nokia
RX-51 board.
The change is taken from MeeGo kernel adaptation for Nokia N900, it repeats the
work of Aaro Koskinen and Mika Laitio, the original discussion is at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
---
arch/arm/mach-omap2/board-rx51-peripherals.c | 45 ++++++++++++++++++++++++-
1 files changed, 43 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index ba1aa07..f30484e 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -15,6 +15,7 @@
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
#include <linux/wl12xx.h>
+#include <linux/spi/tsc2005.h>
#include <linux/i2c.h>
#include <linux/i2c/twl.h>
#include <linux/clk.h>
@@ -56,6 +57,9 @@
#define RX51_FMTX_IRQ 53
#define RX51_LP5523_CHIP_EN_GPIO 41
+#define RX51_TSC2005_RESET_GPIO 104
+#define RX51_TSC2005_IRQ_GPIO 100
+
#define RX51_USB_TRANSCEIVER_RST_GPIO 67
/* list all spi devices here */
@@ -146,6 +150,17 @@ static struct omap2_mcspi_device_config tsc2005_mcspi_config = {
.single_channel = 1,
};
+static struct tsc2005_platform_data tsc2005_pdata = {
+ .ts_pressure_max = 2048,
+ .ts_pressure_fudge = 2,
+ .ts_x_max = 4096,
+ .ts_x_fudge = 4,
+ .ts_y_max = 4096,
+ .ts_y_fudge = 4,
+ .ts_x_plate_ohm = 320,
+ .esd_timeout_ms = 8000,
+};
+
static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
[RX51_SPI_WL1251] = {
.modalias = "wl1251",
@@ -167,10 +182,10 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
.modalias = "tsc2005",
.bus_num = 1,
.chip_select = 0,
- /* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/
+ .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),
.max_speed_hz = 6000000,
.controller_data = &tsc2005_mcspi_config,
- /* .platform_data = &tsc2005_config,*/
+ .platform_data = &tsc2005_pdata,
},
};
@@ -1086,6 +1101,31 @@ error:
*/
}
+static void rx51_tsc2005_set_reset(bool enable)
+{
+ gpio_set_value(RX51_TSC2005_RESET_GPIO, enable);
+}
+
+static void __init rx51_init_tsc2005(void)
+{
+ int r;
+
+ r = gpio_request(RX51_TSC2005_IRQ_GPIO, "tsc2005 IRQ");
+ if (r >= 0)
+ gpio_direction_input(RX51_TSC2005_IRQ_GPIO);
+ else
+ printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 IRQ");
+
+ r = gpio_request(RX51_TSC2005_RESET_GPIO, "tsc2005 reset");
+ if (r >= 0) {
+ gpio_direction_output(RX51_TSC2005_RESET_GPIO, 1);
+ tsc2005_pdata.set_reset = rx51_tsc2005_set_reset;
+ } else {
+ printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 reset");
+ tsc2005_pdata.esd_timeout_ms = 0;
+ }
+}
+
void __init rx51_peripherals_init(void)
{
rx51_i2c_init();
@@ -1094,6 +1134,7 @@ void __init rx51_peripherals_init(void)
board_smc91x_init();
rx51_add_gpio_keys();
rx51_init_wl1251();
+ rx51_init_tsc2005();
rx51_init_si4713();
spi_register_board_info(rx51_peripherals_spi_board_info,
ARRAY_SIZE(rx51_peripherals_spi_board_info));
--
1.7.2.3
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2] OMAP3: RX-51: complete tsc2005 controller support
2011-12-14 13:01 [PATCH] OMAP3: RX-51: complete tsc2005 controller support Vladimir Zapolskiy
@ 2011-12-14 13:02 ` Vladimir Zapolskiy
2011-12-14 14:32 ` Igor Grinberg
2011-12-14 15:45 ` [PATCH] " Aaro Koskinen
1 sibling, 1 reply; 6+ messages in thread
From: Vladimir Zapolskiy @ 2011-12-14 13:02 UTC (permalink / raw)
To: linux-omap, linux-input; +Cc: Dmitry Torokhov, Aaro Koskinen, Tony Lindgren
This change adds initialization of TSC2005 touchscreen controller found on Nokia
RX-51 board.
The change is taken from MeeGo kernel adaptation for Nokia N900, it repeats the
work of Aaro Koskinen and Mika Laitio, the original discussion is at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
---
Changes from v1 to v2:
* whitespace fix
arch/arm/mach-omap2/board-rx51-peripherals.c | 45 ++++++++++++++++++++++++-
1 files changed, 43 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index ba1aa07..f30484e 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -15,6 +15,7 @@
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
#include <linux/wl12xx.h>
+#include <linux/spi/tsc2005.h>
#include <linux/i2c.h>
#include <linux/i2c/twl.h>
#include <linux/clk.h>
@@ -56,6 +57,9 @@
#define RX51_FMTX_IRQ 53
#define RX51_LP5523_CHIP_EN_GPIO 41
+#define RX51_TSC2005_RESET_GPIO 104
+#define RX51_TSC2005_IRQ_GPIO 100
+
#define RX51_USB_TRANSCEIVER_RST_GPIO 67
/* list all spi devices here */
@@ -146,6 +150,17 @@ static struct omap2_mcspi_device_config tsc2005_mcspi_config = {
.single_channel = 1,
};
+static struct tsc2005_platform_data tsc2005_pdata = {
+ .ts_pressure_max = 2048,
+ .ts_pressure_fudge = 2,
+ .ts_x_max = 4096,
+ .ts_x_fudge = 4,
+ .ts_y_max = 4096,
+ .ts_y_fudge = 4,
+ .ts_x_plate_ohm = 320,
+ .esd_timeout_ms = 8000,
+};
+
static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
[RX51_SPI_WL1251] = {
.modalias = "wl1251",
@@ -167,10 +182,10 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
.modalias = "tsc2005",
.bus_num = 1,
.chip_select = 0,
- /* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/
+ .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),
.max_speed_hz = 6000000,
.controller_data = &tsc2005_mcspi_config,
- /* .platform_data = &tsc2005_config,*/
+ .platform_data = &tsc2005_pdata,
},
};
@@ -1086,6 +1101,31 @@ error:
*/
}
+static void rx51_tsc2005_set_reset(bool enable)
+{
+ gpio_set_value(RX51_TSC2005_RESET_GPIO, enable);
+}
+
+static void __init rx51_init_tsc2005(void)
+{
+ int r;
+
+ r = gpio_request(RX51_TSC2005_IRQ_GPIO, "tsc2005 IRQ");
+ if (r >= 0)
+ gpio_direction_input(RX51_TSC2005_IRQ_GPIO);
+ else
+ printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 IRQ");
+
+ r = gpio_request(RX51_TSC2005_RESET_GPIO, "tsc2005 reset");
+ if (r >= 0) {
+ gpio_direction_output(RX51_TSC2005_RESET_GPIO, 1);
+ tsc2005_pdata.set_reset = rx51_tsc2005_set_reset;
+ } else {
+ printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 reset");
+ tsc2005_pdata.esd_timeout_ms = 0;
+ }
+}
+
void __init rx51_peripherals_init(void)
{
rx51_i2c_init();
@@ -1094,6 +1134,7 @@ void __init rx51_peripherals_init(void)
board_smc91x_init();
rx51_add_gpio_keys();
rx51_init_wl1251();
+ rx51_init_tsc2005();
rx51_init_si4713();
spi_register_board_info(rx51_peripherals_spi_board_info,
ARRAY_SIZE(rx51_peripherals_spi_board_info));
--
1.7.2.3
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v2] OMAP3: RX-51: complete tsc2005 controller support
2011-12-14 13:02 ` [PATCH v2] " Vladimir Zapolskiy
@ 2011-12-14 14:32 ` Igor Grinberg
2011-12-14 15:39 ` Vladimir Zapolskiy
0 siblings, 1 reply; 6+ messages in thread
From: Igor Grinberg @ 2011-12-14 14:32 UTC (permalink / raw)
To: Vladimir Zapolskiy
Cc: linux-omap, linux-input, Dmitry Torokhov, Aaro Koskinen,
Tony Lindgren
Hi Vladimir,
On 12/14/11 15:02, Vladimir Zapolskiy wrote:
> This change adds initialization of TSC2005 touchscreen controller found on Nokia
> RX-51 board.
>
> The change is taken from MeeGo kernel adaptation for Nokia N900, it repeats the
> work of Aaro Koskinen and Mika Laitio, the original discussion is at
> http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html
>
> Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
> Cc: Tony Lindgren <tony@atomide.com>
> Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
> ---
> Changes from v1 to v2:
> * whitespace fix
>
> arch/arm/mach-omap2/board-rx51-peripherals.c | 45 ++++++++++++++++++++++++-
> 1 files changed, 43 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
> index ba1aa07..f30484e 100644
> --- a/arch/arm/mach-omap2/board-rx51-peripherals.c
> +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
> @@ -15,6 +15,7 @@
> #include <linux/input/matrix_keypad.h>
> #include <linux/spi/spi.h>
> #include <linux/wl12xx.h>
> +#include <linux/spi/tsc2005.h>
> #include <linux/i2c.h>
> #include <linux/i2c/twl.h>
> #include <linux/clk.h>
> @@ -56,6 +57,9 @@
> #define RX51_FMTX_IRQ 53
> #define RX51_LP5523_CHIP_EN_GPIO 41
>
> +#define RX51_TSC2005_RESET_GPIO 104
> +#define RX51_TSC2005_IRQ_GPIO 100
> +
> #define RX51_USB_TRANSCEIVER_RST_GPIO 67
>
> /* list all spi devices here */
> @@ -146,6 +150,17 @@ static struct omap2_mcspi_device_config tsc2005_mcspi_config = {
> .single_channel = 1,
> };
>
> +static struct tsc2005_platform_data tsc2005_pdata = {
> + .ts_pressure_max = 2048,
> + .ts_pressure_fudge = 2,
> + .ts_x_max = 4096,
> + .ts_x_fudge = 4,
> + .ts_y_max = 4096,
> + .ts_y_fudge = 4,
> + .ts_x_plate_ohm = 320,
> + .esd_timeout_ms = 8000,
> +};
> +
> static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
> [RX51_SPI_WL1251] = {
> .modalias = "wl1251",
> @@ -167,10 +182,10 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
> .modalias = "tsc2005",
> .bus_num = 1,
> .chip_select = 0,
> - /* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/
> + .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),
> .max_speed_hz = 6000000,
> .controller_data = &tsc2005_mcspi_config,
> - /* .platform_data = &tsc2005_config,*/
> + .platform_data = &tsc2005_pdata,
> },
> };
>
> @@ -1086,6 +1101,31 @@ error:
> */
> }
>
> +static void rx51_tsc2005_set_reset(bool enable)
> +{
> + gpio_set_value(RX51_TSC2005_RESET_GPIO, enable);
> +}
> +
> +static void __init rx51_init_tsc2005(void)
> +{
> + int r;
> +
> + r = gpio_request(RX51_TSC2005_IRQ_GPIO, "tsc2005 IRQ");
> + if (r >= 0)
> + gpio_direction_input(RX51_TSC2005_IRQ_GPIO);
> + else
> + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 IRQ");
> +
> + r = gpio_request(RX51_TSC2005_RESET_GPIO, "tsc2005 reset");
> + if (r >= 0) {
> + gpio_direction_output(RX51_TSC2005_RESET_GPIO, 1);
> + tsc2005_pdata.set_reset = rx51_tsc2005_set_reset;
> + } else {
> + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 reset");
> + tsc2005_pdata.esd_timeout_ms = 0;
> + }
I would suggest using gpio_request_array() here,
or if those pins are independent from each other, for some reason,
then gpio_request_one() would do.
Also, don't you need to setup the mux for these GPIOs?
Or is it done in some other place (like bootloader)?
> +}
> +
> void __init rx51_peripherals_init(void)
> {
> rx51_i2c_init();
> @@ -1094,6 +1134,7 @@ void __init rx51_peripherals_init(void)
> board_smc91x_init();
> rx51_add_gpio_keys();
> rx51_init_wl1251();
> + rx51_init_tsc2005();
> rx51_init_si4713();
> spi_register_board_info(rx51_peripherals_spi_board_info,
> ARRAY_SIZE(rx51_peripherals_spi_board_info));
--
Regards,
Igor.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2] OMAP3: RX-51: complete tsc2005 controller support
2011-12-14 14:32 ` Igor Grinberg
@ 2011-12-14 15:39 ` Vladimir Zapolskiy
0 siblings, 0 replies; 6+ messages in thread
From: Vladimir Zapolskiy @ 2011-12-14 15:39 UTC (permalink / raw)
To: ext Igor Grinberg
Cc: linux-omap, linux-input, Dmitry Torokhov, Aaro Koskinen,
Tony Lindgren
Hi Igor,
thanks for review.
On 12/14/2011 04:32 PM, ext Igor Grinberg wrote:
> Hi Vladimir,
>
> On 12/14/11 15:02, Vladimir Zapolskiy wrote:
>> This change adds initialization of TSC2005 touchscreen controller found on Nokia
>> RX-51 board.
>>
>> The change is taken from MeeGo kernel adaptation for Nokia N900, it repeats the
>> work of Aaro Koskinen and Mika Laitio, the original discussion is at
>> http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html
>>
>> Signed-off-by: Vladimir Zapolskiy<vladimir.zapolskiy@nokia.com>
>> Cc: Tony Lindgren<tony@atomide.com>
>> Cc: Aaro Koskinen<aaro.koskinen@nokia.com>
>> Cc: Dmitry Torokhov<dmitry.torokhov@gmail.com>
>> ---
>> Changes from v1 to v2:
>> * whitespace fix
>>
>> arch/arm/mach-omap2/board-rx51-peripherals.c | 45 ++++++++++++++++++++++++-
>> 1 files changed, 43 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
>> index ba1aa07..f30484e 100644
>> --- a/arch/arm/mach-omap2/board-rx51-peripherals.c
>> +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
>> @@ -15,6 +15,7 @@
>> #include<linux/input/matrix_keypad.h>
>> #include<linux/spi/spi.h>
>> #include<linux/wl12xx.h>
>> +#include<linux/spi/tsc2005.h>
>> #include<linux/i2c.h>
>> #include<linux/i2c/twl.h>
>> #include<linux/clk.h>
>> @@ -56,6 +57,9 @@
>> #define RX51_FMTX_IRQ 53
>> #define RX51_LP5523_CHIP_EN_GPIO 41
>>
>> +#define RX51_TSC2005_RESET_GPIO 104
>> +#define RX51_TSC2005_IRQ_GPIO 100
>> +
>> #define RX51_USB_TRANSCEIVER_RST_GPIO 67
>>
>> /* list all spi devices here */
>> @@ -146,6 +150,17 @@ static struct omap2_mcspi_device_config tsc2005_mcspi_config = {
>> .single_channel = 1,
>> };
>>
>> +static struct tsc2005_platform_data tsc2005_pdata = {
>> + .ts_pressure_max = 2048,
>> + .ts_pressure_fudge = 2,
>> + .ts_x_max = 4096,
>> + .ts_x_fudge = 4,
>> + .ts_y_max = 4096,
>> + .ts_y_fudge = 4,
>> + .ts_x_plate_ohm = 320,
>> + .esd_timeout_ms = 8000,
>> +};
>> +
>> static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
>> [RX51_SPI_WL1251] = {
>> .modalias = "wl1251",
>> @@ -167,10 +182,10 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
>> .modalias = "tsc2005",
>> .bus_num = 1,
>> .chip_select = 0,
>> - /* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/
>> + .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),
>> .max_speed_hz = 6000000,
>> .controller_data =&tsc2005_mcspi_config,
>> - /* .platform_data =&tsc2005_config,*/
>> + .platform_data =&tsc2005_pdata,
>> },
>> };
>>
>> @@ -1086,6 +1101,31 @@ error:
>> */
>> }
>>
>> +static void rx51_tsc2005_set_reset(bool enable)
>> +{
>> + gpio_set_value(RX51_TSC2005_RESET_GPIO, enable);
>> +}
>> +
>> +static void __init rx51_init_tsc2005(void)
>> +{
>> + int r;
>> +
>> + r = gpio_request(RX51_TSC2005_IRQ_GPIO, "tsc2005 IRQ");
>> + if (r>= 0)
>> + gpio_direction_input(RX51_TSC2005_IRQ_GPIO);
>> + else
>> + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 IRQ");
>> +
>> + r = gpio_request(RX51_TSC2005_RESET_GPIO, "tsc2005 reset");
>> + if (r>= 0) {
>> + gpio_direction_output(RX51_TSC2005_RESET_GPIO, 1);
>> + tsc2005_pdata.set_reset = rx51_tsc2005_set_reset;
>> + } else {
>> + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 reset");
>> + tsc2005_pdata.esd_timeout_ms = 0;
>> + }
>
> I would suggest using gpio_request_array() here,
> or if those pins are independent from each other, for some reason,
> then gpio_request_one() would do.
These pins are actually independent, but I agree that it would be
simpler and therefore better to use gpio_request_array() here.
> Also, don't you need to setup the mux for these GPIOs?
> Or is it done in some other place (like bootloader)?
I presume it's done in the original bootloader, however it won't harm to
add explicit pin mux definitions.
>> +}
>> +
>> void __init rx51_peripherals_init(void)
>> {
>> rx51_i2c_init();
>> @@ -1094,6 +1134,7 @@ void __init rx51_peripherals_init(void)
>> board_smc91x_init();
>> rx51_add_gpio_keys();
>> rx51_init_wl1251();
>> + rx51_init_tsc2005();
>> rx51_init_si4713();
>> spi_register_board_info(rx51_peripherals_spi_board_info,
>> ARRAY_SIZE(rx51_peripherals_spi_board_info));
>
--
With best wishes,
Vladimir
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] OMAP3: RX-51: complete tsc2005 controller support
2011-12-14 13:01 [PATCH] OMAP3: RX-51: complete tsc2005 controller support Vladimir Zapolskiy
2011-12-14 13:02 ` [PATCH v2] " Vladimir Zapolskiy
@ 2011-12-14 15:45 ` Aaro Koskinen
2011-12-14 15:59 ` Vladimir Zapolskiy
1 sibling, 1 reply; 6+ messages in thread
From: Aaro Koskinen @ 2011-12-14 15:45 UTC (permalink / raw)
To: Vladimir Zapolskiy
Cc: linux-omap, linux-input, Dmitry Torokhov, Aaro Koskinen,
Tony Lindgren
Hi,
On Wed, 14 Dec 2011, Vladimir Zapolskiy wrote:
> This change adds initialization of TSC2005 touchscreen controller
> found on Nokia RX-51 board.
>
> The change is taken from MeeGo kernel adaptation for Nokia N900,
> it repeats the work of Aaro Koskinen and Mika Laitio, the original
> discussion is at
> http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html
I think Tony applied this already:
http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=commit;h=3dad5356aa47097cf67027cf0a07298b4f5baef6
And that patch was from Maemo, not MeeGo kernel...
A.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] OMAP3: RX-51: complete tsc2005 controller support
2011-12-14 15:45 ` [PATCH] " Aaro Koskinen
@ 2011-12-14 15:59 ` Vladimir Zapolskiy
0 siblings, 0 replies; 6+ messages in thread
From: Vladimir Zapolskiy @ 2011-12-14 15:59 UTC (permalink / raw)
To: Aaro Koskinen; +Cc: linux-omap, linux-input, Dmitry Torokhov, Tony Lindgren
Hi,
On 12/14/2011 05:45 PM, Aaro Koskinen wrote:
> Hi,
>
> On Wed, 14 Dec 2011, Vladimir Zapolskiy wrote:
>> This change adds initialization of TSC2005 touchscreen controller
>> found on Nokia RX-51 board.
>>
>> The change is taken from MeeGo kernel adaptation for Nokia N900,
>> it repeats the work of Aaro Koskinen and Mika Laitio, the original
>> discussion is at
>> http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html
>
> I think Tony applied this already:
>
> http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=commit;h=3dad5356aa47097cf67027cf0a07298b4f5baef6
>
great, I haven't noticed that initially. In that case please ignore the
duplicate.
>
> And that patch was from Maemo, not MeeGo kernel...
>
> A.
--
With best wishes,
Vladimir
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2011-12-14 15:59 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-12-14 13:01 [PATCH] OMAP3: RX-51: complete tsc2005 controller support Vladimir Zapolskiy
2011-12-14 13:02 ` [PATCH v2] " Vladimir Zapolskiy
2011-12-14 14:32 ` Igor Grinberg
2011-12-14 15:39 ` Vladimir Zapolskiy
2011-12-14 15:45 ` [PATCH] " Aaro Koskinen
2011-12-14 15:59 ` Vladimir Zapolskiy
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).