Re: [PATCH 5/5] regulator: qcom_rpm-regulator: Add support for pm8018 rpm regulator

[Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>]

On 06/17/2016 06:53 PM, Bjorn Andersson wrote:
> On Fri 17 Jun 03:22 PDT 2016, Neil Armstrong wrote:
> 
>> In order to support eh Qualcomm MDM9615 SoC, add support for the
>> PM8018 RPM regulator in the qcom_rpm-regulator driver.
>>
>> Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> [..]
>> diff --git a/drivers/regulator/qcom_rpm-regulator.c b/drivers/regulator/qcom_rpm-regulator.c
> [..]
>> +/**
>> + * enum rpm_vreg_voltage_corner - possible voltage corner values
>> + *
>> + * These should be used in regulator_set_voltage and rpm_vreg_set_voltage calls
>> + * for corner type regulators as if they had units of uV.
>> + */
>> +enum rpm_vreg_voltage_corner {
>> +	RPM_VREG_CORNER_NONE = 1,
>> +	RPM_VREG_CORNER_LOW,
>> +	RPM_VREG_CORNER_NOMINAL,
>> +	RPM_VREG_CORNER_HIGH,
>> +};
>> +
>> +static struct regulator_linear_range corner_ranges[] = {
>> +	REGULATOR_LINEAR_RANGE(RPM_VREG_CORNER_NONE, 0,
>> +				RPM_VREG_CORNER_HIGH, 1),
>> +};
>> +
>>  static int rpm_reg_write(struct qcom_rpm_reg *vreg,
> [..]
>> +
>> +static const struct qcom_rpm_reg pm8018_corner = {
>> +	.desc.linear_ranges = corner_ranges,
>> +	.desc.n_linear_ranges = ARRAY_SIZE(corner_ranges),
>> +	.desc.n_voltages = 4,
>> +	.desc.ops = &uV_ops,
>> +	.parts = &rpm8018_corner_parts,
>> +};
>> +
> [..]
>> +static const struct rpm_regulator_data rpm_pm8018_regulators[] = {
> [..]
>> +	{ "dig_corner", QCOM_RPM_VOLTAGE_CORNER, &pm8018_corner,
>> +						      "vdd_dig_corner" },
>> +
>> +	{ }
>> +};
> 
> We have discussed the corners for a long time and I think we've
> concluded that they should be exposed as something like an OPP. What we
> have agreed on is that they should not be exposed as a regulator with
> voltages 1-4uV.
> 
> So please drop the corner for now.
> 
> Regards,
> Bjorn
> 
OK, dropped.

Thanks,
Neil

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.