From: Nayna Jain <nayna@linux.vnet.ibm.com>
To: linux-integrity@vger.kernel.org
Cc: zohar@linux.vnet.ibm.com, linux-security-module@vger.kernel.org,
linux-kernel@vger.kernel.org, peterhuewe@gmx.de,
jarkko.sakkinen@linux.intel.com, tpmdd@selhorst.net,
jgunthorpe@obsidianresearch.com, patrickc@us.ibm.com,
Nayna Jain <nayna@linux.vnet.ibm.com>
Subject: [PATCH v4 0/4] additional TPM performance improvements
Date: Tue, 17 Oct 2017 16:32:28 -0400 [thread overview]
Message-ID: <20171017203232.2262-1-nayna@linux.vnet.ibm.com> (raw)
After further discussions with the TCG Device Driver working group (ddwg),
the following changes were made:
* Check for burstcount at least once to confirm the TPM is ready to accept
the data. Similarly, query for the TPM Expect status as sanity check at
the end.
* Make the sleep for status check in the loop less than 5msec.
* Make the sleep in the loop while querying for burstcount less than
5msec.
Below is the list of patches along with the performance improvements
seen with a TPM 1.2 with an 8 byte burstcount for 1000 extends:
Patch |Improvement(time in sec)
tpm: ignore burstcount to improve tpm_tis | ~41 - ~14
send() performance.
tpm: reduce polling delay in tpm_tis_core | ~14 - ~9
tpm: modify tpm_msleep() function to have | ~9 - ~8
max range
Changelog v4:
* Include Jarkko's feedback on merging two patches reducing sleep
time during polling to TPM.
* Include Jarkko's feedback to clean up the burstcount change
patch and add comment for new #define.
Changelog v3:
* Include Jarkko's feedback to move wait_for_tpm_stat() from
tpm-interface.c to respective driver files tpm_tis_core.c and
xen-tpmfront.c.
* Remove use of module parameter ignore_burst_count and is
now alwaysed ignored in tpm tis send() operation.
* Reduce sleep() time during polling in wait_for_tpm_stat() from
5msec to 1msec for both recv() and send() operation. Version
2 of the patches had it only for send() operation.
Changelog v2:
* Add module parameter to handle ignoring of burst count during
tpm tis send() operation.
* Add improvements over sleep time to reduce delays.
Nayna Jain (4):
tpm: move wait_for_tpm_stat() to respective driver files
tpm: ignore burstcount to improve tpm_tis send() performance
tpm: reduce tpm polling delay in tpm_tis_core
tpm: use tpm_msleep() value as max delay
drivers/char/tpm/tpm-interface.c | 60 ---------------------
drivers/char/tpm/tpm.h | 6 +--
drivers/char/tpm/tpm_tis_core.c | 110 +++++++++++++++++++++++++++++----------
drivers/char/tpm/xen-tpmfront.c | 60 +++++++++++++++++++++
4 files changed, 144 insertions(+), 92 deletions(-)
--
2.13.3
next reply other threads:[~2017-10-17 20:32 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-10-17 20:32 Nayna Jain [this message]
2017-10-17 20:32 ` [PATCH v4 1/4] tpm: move wait_for_tpm_stat() to respective driver files Nayna Jain
2017-10-19 14:21 ` Jarkko Sakkinen
2017-10-19 17:00 ` Alexander.Steffen
2017-10-20 8:56 ` Jarkko Sakkinen
2017-10-23 13:32 ` Nayna Jain
2017-10-24 13:45 ` Jarkko Sakkinen
2017-10-17 20:32 ` [PATCH v4 2/4] tpm: ignore burstcount to improve tpm_tis send() performance Nayna Jain
2017-10-18 15:25 ` Jarkko Sakkinen
2017-10-19 14:23 ` Jarkko Sakkinen
2017-10-20 14:42 ` Alexander.Steffen
2017-10-20 18:02 ` Ken Goldman
2017-10-23 2:57 ` Jarkko Sakkinen
2017-11-07 18:29 ` Nayna Jain
2017-11-08 11:32 ` Alexander.Steffen
2017-11-16 14:34 ` Alexander.Steffen
2017-11-22 6:52 ` Alexander.Steffen
2017-11-23 14:47 ` Nayna Jain
2017-11-23 16:19 ` Alexander.Steffen
2017-11-26 15:22 ` Jarkko Sakkinen
2017-11-26 16:37 ` Mimi Zohar
2017-11-27 7:08 ` Leendert van Doorn
2017-11-27 13:22 ` Mimi Zohar
2017-11-28 20:19 ` Jarkko Sakkinen
2017-10-17 20:32 ` [PATCH v4 3/4] tpm: reduce tpm polling delay in tpm_tis_core Nayna Jain
2017-10-18 15:24 ` Jarkko Sakkinen
2017-10-19 14:22 ` Jarkko Sakkinen
2017-10-17 20:32 ` [PATCH v4 4/4] tpm: use tpm_msleep() value as max delay Nayna Jain
2017-10-19 14:22 ` Jarkko Sakkinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171017203232.2262-1-nayna@linux.vnet.ibm.com \
--to=nayna@linux.vnet.ibm.com \
--cc=jarkko.sakkinen@linux.intel.com \
--cc=jgunthorpe@obsidianresearch.com \
--cc=linux-integrity@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-security-module@vger.kernel.org \
--cc=patrickc@us.ibm.com \
--cc=peterhuewe@gmx.de \
--cc=tpmdd@selhorst.net \
--cc=zohar@linux.vnet.ibm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).