From: Konrad Rzeszutek Wilk <konrad.wilk-QHcLZuEGTsvQT0dZR+AlfA@public.gmane.org>
To: Joerg Roedel <joerg.roedel-5C7GfCeVMHo@public.gmane.org>
Cc: iommu-cunTk1MwBs9QetFLy7KEm3xJsTq8ys+cHZ5vskTnxNA@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: Re: [PATCH 05/16] iommu/amd: Split device table initialization into irq and dma part
Date: Fri, 28 Sep 2012 10:17:53 -0400 [thread overview]
Message-ID: <20120928141752.GD7483@localhost.localdomain> (raw)
In-Reply-To: <1348835046-3262-6-git-send-email-joerg.roedel-5C7GfCeVMHo@public.gmane.org>
On Fri, Sep 28, 2012 at 02:23:55PM +0200, Joerg Roedel wrote:
> When the IOMMU is enabled very early (as with irq-remapping)
> some devices are still in BIOS hand. When dma is blocked
> early this can cause lots of IO_PAGE_FAULTs. So delay the
> DMA initialization and do it right before the dma_ops are
> initialized.
> To be secure, block all interrupts by default when irq-remapping is
What are you trying to be secure against?
> enabled in the system. They will be reenabled on demand
> later.
>
> Signed-off-by: Joerg Roedel <joerg.roedel-5C7GfCeVMHo@public.gmane.org>
> ---
> drivers/iommu/amd_iommu_init.c | 19 ++++++++++++++++++-
> 1 file changed, 18 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/iommu/amd_iommu_init.c b/drivers/iommu/amd_iommu_init.c
> index 3f0b68f..8e9d71c 100644
> --- a/drivers/iommu/amd_iommu_init.c
> +++ b/drivers/iommu/amd_iommu_init.c
> @@ -1378,7 +1378,7 @@ static int __init init_memory_definitions(struct acpi_table_header *table)
> * Init the device table to not allow DMA access for devices and
> * suppress all page faults
> */
> -static void init_device_table(void)
> +static void init_device_table_dma(void)
> {
> u32 devid;
>
> @@ -1388,6 +1388,17 @@ static void init_device_table(void)
> }
> }
>
> +static void init_device_table(void)
> +{
> + u32 devid;
> +
> + if (!amd_iommu_irq_remap)
> + return;
> +
> + for (devid = 0; devid <= amd_iommu_last_bdf; ++devid)
> + set_dev_entry_bit(devid, DEV_ENTRY_IRQ_TBL_EN);
> +}
> +
> static void iommu_init_flags(struct amd_iommu *iommu)
> {
> iommu->acpi_flags & IVHD_FLAG_HT_TUN_EN_MASK ?
> @@ -1778,8 +1789,14 @@ static bool detect_ivrs(void)
>
> static int amd_iommu_init_dma(void)
> {
> + struct amd_iommu *iommu;
> int ret;
>
> + init_device_table_dma();
> +
> + for_each_iommu(iommu)
> + iommu_flush_all_caches(iommu);
> +
> if (iommu_pass_through)
> ret = amd_iommu_init_passthrough();
> else
> --
> 1.7.9.5
>
>
> _______________________________________________
> iommu mailing list
> iommu-cunTk1MwBs9QetFLy7KEm3xJsTq8ys+cHZ5vskTnxNA@public.gmane.org
> https://lists.linuxfoundation.org/mailman/listinfo/iommu
next prev parent reply other threads:[~2012-09-28 14:17 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-09-28 12:23 [PATCH 0/16] Interrupt remapping support for AMD IOMMU Joerg Roedel
[not found] ` <1348835046-3262-1-git-send-email-joerg.roedel-5C7GfCeVMHo@public.gmane.org>
2012-09-28 12:23 ` [PATCH 01/16] iommu/amd: Keep track of HPET and IOAPIC device ids Joerg Roedel
2012-09-28 14:08 ` Konrad Rzeszutek Wilk
[not found] ` <20120928140833.GB7483-bi+AKbBUZKY6gyzm1THtWbp2dZbC/Bob@public.gmane.org>
2012-09-28 14:35 ` Joerg Roedel
2012-09-28 12:23 ` [PATCH 02/16] iommu/amd: Add slab-cache for irq remapping tables Joerg Roedel
2012-09-28 12:23 ` [PATCH 03/16] iommu/amd: Allocate data structures to keep track of " Joerg Roedel
2012-09-28 22:57 ` Shuah Khan
2012-09-28 12:23 ` [PATCH 04/16] iommu/amd: Check if IOAPIC information is correct Joerg Roedel
[not found] ` <1348835046-3262-5-git-send-email-joerg.roedel-5C7GfCeVMHo@public.gmane.org>
2012-09-28 14:16 ` Konrad Rzeszutek Wilk
[not found] ` <20120928141644.GC7483-bi+AKbBUZKY6gyzm1THtWbp2dZbC/Bob@public.gmane.org>
2012-09-28 14:37 ` Joerg Roedel
2012-09-28 12:23 ` [PATCH 05/16] iommu/amd: Split device table initialization into irq and dma part Joerg Roedel
[not found] ` <1348835046-3262-6-git-send-email-joerg.roedel-5C7GfCeVMHo@public.gmane.org>
2012-09-28 14:17 ` Konrad Rzeszutek Wilk [this message]
[not found] ` <20120928141752.GD7483-bi+AKbBUZKY6gyzm1THtWbp2dZbC/Bob@public.gmane.org>
2012-09-28 14:25 ` Joerg Roedel
[not found] ` <20120928142555.GC4009-5C7GfCeVMHo@public.gmane.org>
2012-09-28 15:00 ` Konrad Rzeszutek Wilk
[not found] ` <20120928150009.GI7483-bi+AKbBUZKY6gyzm1THtWbp2dZbC/Bob@public.gmane.org>
2012-09-28 14:59 ` Joerg Roedel
2012-09-28 12:23 ` [PATCH 06/16] iommu/amd: Make sure IOMMU is not considered to translate itself Joerg Roedel
2012-09-28 12:23 ` [PATCH 07/16] iommu/amd: Add IRTE invalidation routine Joerg Roedel
[not found] ` <1348835046-3262-8-git-send-email-joerg.roedel-5C7GfCeVMHo@public.gmane.org>
2012-09-28 14:20 ` Konrad Rzeszutek Wilk
2012-09-28 15:36 ` Joerg Roedel
2012-09-28 12:23 ` [PATCH 08/16] iommu/amd: Add routines to manage irq remapping tables Joerg Roedel
[not found] ` <1348835046-3262-9-git-send-email-joerg.roedel-5C7GfCeVMHo@public.gmane.org>
2012-09-28 14:40 ` Konrad Rzeszutek Wilk
[not found] ` <20120928144011.GF7483-bi+AKbBUZKY6gyzm1THtWbp2dZbC/Bob@public.gmane.org>
2012-09-28 15:01 ` Joerg Roedel
2012-09-28 12:23 ` [PATCH 09/16] iommu/amd: Add IOAPIC remapping routines Joerg Roedel
[not found] ` <1348835046-3262-10-git-send-email-joerg.roedel-5C7GfCeVMHo@public.gmane.org>
2012-09-28 14:45 ` Konrad Rzeszutek Wilk
[not found] ` <6d716497-bcf6-4d71-88a3-6ec772a4d396@sausexedgep01.amd.com>
[not found] ` <6d716497-bcf6-4d71-88a3-6ec772a4d396-drQb3oNRF8yAbyOsnIB/ifZ4XP/Yx64J@public.gmane.org>
2012-10-01 8:40 ` Joerg Roedel
[not found] ` <20121001084051.GO4009-5C7GfCeVMHo@public.gmane.org>
2012-10-01 13:47 ` Konrad Rzeszutek Wilk
[not found] ` <20121001134753.GF4099-6K5HmflnPlqSPmnEAIUT9EEOCMrvLtNR@public.gmane.org>
2012-10-01 16:33 ` Joerg Roedel
2012-10-01 16:34 ` Konrad Rzeszutek Wilk
2012-09-28 12:24 ` [PATCH 10/16] iommu/amd: Implement MSI routines for interrupt remapping Joerg Roedel
[not found] ` <1348835046-3262-11-git-send-email-joerg.roedel-5C7GfCeVMHo@public.gmane.org>
2012-09-28 14:49 ` Konrad Rzeszutek Wilk
[not found] ` <20120928144933.GH7483-bi+AKbBUZKY6gyzm1THtWbp2dZbC/Bob@public.gmane.org>
2012-09-28 15:04 ` Joerg Roedel
2012-09-28 12:24 ` [PATCH 11/16] iommu/amd: Add call-back routine for HPET MSI Joerg Roedel
2012-09-28 12:24 ` [PATCH 12/16] iommu/amd: Add initialization routines for AMD interrupt remapping Joerg Roedel
2012-09-28 23:18 ` Shuah Khan
[not found] ` <CAKocOONojx7tvu6x+HV97Rae-KXA3hW65Ujmt2t7LCVs9oRpyw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2012-10-01 8:05 ` Joerg Roedel
2012-10-01 16:02 ` Shuah Khan
2012-09-28 12:24 ` [PATCH 13/16] iommu/amd: Make sure irq remapping still works on dma init failure Joerg Roedel
2012-09-28 12:24 ` [PATCH 14/16] iommu/irq: Use amd_iommu_irq_ops if supported Joerg Roedel
2012-09-28 23:39 ` Shuah Khan
[not found] ` <CAKocOONaiMJs7pWeWxO=_bN5_KU=jZh=kvL7U_v-w9LmSrQ+Fw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2012-10-01 8:08 ` Joerg Roedel
2012-10-01 16:04 ` Shuah Khan
2012-09-28 12:24 ` [PATCH 15/16] iommu/amd: Print message to system log when irq remapping is enabled Joerg Roedel
2012-09-28 12:24 ` [PATCH 16/16] iommu/amd: Report irq remapping through IOMMU-API Joerg Roedel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120928141752.GD7483@localhost.localdomain \
--to=konrad.wilk-qhclzuegtsvqt0dzr+alfa@public.gmane.org \
--cc=iommu-cunTk1MwBs9QetFLy7KEm3xJsTq8ys+cHZ5vskTnxNA@public.gmane.org \
--cc=joerg.roedel-5C7GfCeVMHo@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).