Linux IOMMU Development
 help / color / mirror / Atom feed
From: Lu Baolu <baolu.lu@linux.intel.com>
To: Joerg Roedel <joro@8bytes.org>, Will Deacon <will@kernel.org>,
	Robin Murphy <robin.murphy@arm.com>,
	Kevin Tian <kevin.tian@intel.com>,
	Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: iommu@lists.linux.dev, linux-kernel@vger.kernel.org,
	Lu Baolu <baolu.lu@linux.intel.com>
Subject: [PATCH 1/1] iommu/vt-d: Revert ATS timing change to fix boot failure
Date: Wed, 16 Apr 2025 15:36:08 +0800	[thread overview]
Message-ID: <20250416073608.1799578-1-baolu.lu@linux.intel.com> (raw)

Commit <5518f239aff1> ("iommu/vt-d: Move scalable mode ATS enablement to
probe path") changed the PCI ATS enablement logic to run earlier,
specifically before the default domain attachment.

On some client platforms, this change resulted in boot failures, causing
the kernel to panic with the following message and call trace:

 Kernel panic - not syncing: DMAR hardware is malfunctioning
 CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.14.0-rc3+ #175
 Call Trace:
  <TASK>
  dump_stack_lvl+0x6f/0xb0
  dump_stack+0x10/0x16
  panic+0x10a/0x2b7
  iommu_enable_translation.cold+0xc/0xc
  intel_iommu_init+0xe39/0xec0
  ? trace_hardirqs_on+0x1e/0xd0
  ? __pfx_pci_iommu_init+0x10/0x10
  pci_iommu_init+0xd/0x40
  do_one_initcall+0x5b/0x390
  kernel_init_freeable+0x26d/0x2b0
  ? __pfx_kernel_init+0x10/0x10
  kernel_init+0x15/0x120
  ret_from_fork+0x35/0x60
  ? __pfx_kernel_init+0x10/0x10
  ret_from_fork_asm+0x1a/0x30
 RIP: 1f0f:0x0
 Code: Unable to access opcode bytes at 0xffffffffffffffd6.
 RSP: 0000:0000000000000000 EFLAGS: 841f0f2e66 ORIG_RAX:
      1f0f2e6600000000
 RAX: 0000000000000000 RBX: 1f0f2e6600000000 RCX:
      2e66000000000084
 RDX: 0000000000841f0f RSI: 000000841f0f2e66 RDI:
      00841f0f2e660000
 RBP: 00841f0f2e660000 R08: 00841f0f2e660000 R09:
      000000841f0f2e66
 R10: 0000000000841f0f R11: 2e66000000000084 R12:
      000000841f0f2e66
 R13: 0000000000841f0f R14: 2e66000000000084 R15:
      1f0f2e6600000000
  </TASK>
 ---[ end Kernel panic - not syncing: DMAR hardware is malfunctioning ]---

Fix this by reverting the timing change for ATS enablement introduced by
the offending commit and restoring the previous behavior.

Fixes: 5518f239aff1 ("iommu/vt-d: Move scalable mode ATS enablement to probe path")
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Closes: https://lore.kernel.org/linux-iommu/01b9c72f-460d-4f77-b696-54c6825babc9@linux.intel.com/
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
---
 drivers/iommu/intel/iommu.c | 31 +++++++++++++++++++------------
 1 file changed, 19 insertions(+), 12 deletions(-)

diff --git a/drivers/iommu/intel/iommu.c b/drivers/iommu/intel/iommu.c
index b29da2d96d0b..e60b699e7b8c 100644
--- a/drivers/iommu/intel/iommu.c
+++ b/drivers/iommu/intel/iommu.c
@@ -3785,6 +3785,22 @@ static struct iommu_device *intel_iommu_probe_device(struct device *dev)
 
 	intel_iommu_debugfs_create_dev(info);
 
+	return &iommu->iommu;
+free_table:
+	intel_pasid_free_table(dev);
+clear_rbtree:
+	device_rbtree_remove(info);
+free:
+	kfree(info);
+
+	return ERR_PTR(ret);
+}
+
+static void intel_iommu_probe_finalize(struct device *dev)
+{
+	struct device_domain_info *info = dev_iommu_priv_get(dev);
+	struct intel_iommu *iommu = info->iommu;
+
 	/*
 	 * The PCIe spec, in its wisdom, declares that the behaviour of the
 	 * device is undefined if you enable PASID support after ATS support.
@@ -3792,22 +3808,12 @@ static struct iommu_device *intel_iommu_probe_device(struct device *dev)
 	 * we can't yet know if we're ever going to use it.
 	 */
 	if (info->pasid_supported &&
-	    !pci_enable_pasid(pdev, info->pasid_supported & ~1))
+	    !pci_enable_pasid(to_pci_dev(dev), info->pasid_supported & ~1))
 		info->pasid_enabled = 1;
 
-	if (sm_supported(iommu))
+	if (sm_supported(iommu) && !dev_is_real_dma_subdevice(dev))
 		iommu_enable_pci_ats(info);
 	iommu_enable_pci_pri(info);
-
-	return &iommu->iommu;
-free_table:
-	intel_pasid_free_table(dev);
-clear_rbtree:
-	device_rbtree_remove(info);
-free:
-	kfree(info);
-
-	return ERR_PTR(ret);
 }
 
 static void intel_iommu_release_device(struct device *dev)
@@ -4391,6 +4397,7 @@ const struct iommu_ops intel_iommu_ops = {
 	.domain_alloc_sva	= intel_svm_domain_alloc,
 	.domain_alloc_nested	= intel_iommu_domain_alloc_nested,
 	.probe_device		= intel_iommu_probe_device,
+	.probe_finalize		= intel_iommu_probe_finalize,
 	.release_device		= intel_iommu_release_device,
 	.get_resv_regions	= intel_iommu_get_resv_regions,
 	.device_group		= intel_iommu_device_group,
-- 
2.43.0


             reply	other threads:[~2025-04-16  7:35 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-04-16  7:36 Lu Baolu [this message]
2025-04-16  8:37 ` [PATCH 1/1] iommu/vt-d: Revert ATS timing change to fix boot failure Jarkko Nikula
2025-04-17  2:23 ` Tian, Kevin
2025-04-17  2:46   ` Baolu Lu
2025-04-17  3:13     ` Tian, Kevin
2025-04-17 14:45 ` Joerg Roedel

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20250416073608.1799578-1-baolu.lu@linux.intel.com \
    --to=baolu.lu@linux.intel.com \
    --cc=iommu@lists.linux.dev \
    --cc=jarkko.nikula@linux.intel.com \
    --cc=joro@8bytes.org \
    --cc=kevin.tian@intel.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robin.murphy@arm.com \
    --cc=will@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox