Re: [PATCH] docs: ipmi: fix spelling and grammar mistakes

[Corey Minyard <corey@minyard.net>]

On Fri, May 16, 2025 at 12:47:57AM +0100, Praveen Balakrishnan wrote:
> Corrected various spelling and grammatical mistakes in
> Documentation/driver-api/ipmi.rst to improve readability.
> 
> No changes to the technical content has been made.

Thank you, I have added this to my tree.

-corey

> 
> Signed-off-by: Praveen Balakrishnan <praveen.balakrishnan@magd.ox.ac.uk>
> ---
>  Documentation/driver-api/ipmi.rst | 20 ++++++++++----------
>  1 file changed, 10 insertions(+), 10 deletions(-)
> 
> diff --git a/Documentation/driver-api/ipmi.rst b/Documentation/driver-api/ipmi.rst
> index dfa021eacd63..d9fb2376e8da 100644
> --- a/Documentation/driver-api/ipmi.rst
> +++ b/Documentation/driver-api/ipmi.rst
> @@ -45,7 +45,7 @@ manual), choose the 'IPMI SI handler' option.  A driver also exists
>  for direct I2C access to the IPMI management controller.  Some boards
>  support this, but it is unknown if it will work on every board.  For
>  this, choose 'IPMI SMBus handler', but be ready to try to do some
> -figuring to see if it will work on your system if the SMBIOS/APCI
> +figuring to see if it will work on your system if the SMBIOS/ACPI
>  information is wrong or not present.  It is fairly safe to have both
>  these enabled and let the drivers auto-detect what is present.
>  
> @@ -63,7 +63,7 @@ situation, you need to read the section below named 'The SI Driver' or
>  IPMI defines a standard watchdog timer.  You can enable this with the
>  'IPMI Watchdog Timer' config option.  If you compile the driver into
>  the kernel, then via a kernel command-line option you can have the
> -watchdog timer start as soon as it initializes.  It also have a lot
> +watchdog timer start as soon as it initializes.  It also has a lot
>  of other options, see the 'Watchdog' section below for more details.
>  Note that you can also have the watchdog continue to run if it is
>  closed (by default it is disabled on close).  Go into the 'Watchdog
> @@ -317,13 +317,13 @@ This gives the receiver a place to actually put the message.
>  
>  If the message cannot fit into the data you provide, you will get an
>  EMSGSIZE error and the driver will leave the data in the receive
> -queue.  If you want to get it and have it truncate the message, us
> +queue.  If you want to get it and have it truncate the message, use
>  the IPMICTL_RECEIVE_MSG_TRUNC ioctl.
>  
>  When you send a command (which is defined by the lowest-order bit of
>  the netfn per the IPMI spec) on the IPMB bus, the driver will
>  automatically assign the sequence number to the command and save the
> -command.  If the response is not receive in the IPMI-specified 5
> +command.  If the response is not received in the IPMI-specified 5
>  seconds, it will generate a response automatically saying the command
>  timed out.  If an unsolicited response comes in (if it was after 5
>  seconds, for instance), that response will be ignored.
> @@ -367,7 +367,7 @@ channel bitmasks do not overlap.
>  
>  To respond to a received command, set the response bit in the returned
>  netfn, use the address from the received message, and use the same
> -msgid that you got in the receive message.
> +msgid that you got in the received message.
>  
>  From userland, equivalent IOCTLs are provided to do these functions.
>  
> @@ -440,7 +440,7 @@ register would be 0xca6.  This defaults to 1.
>  
>  The regsizes parameter gives the size of a register, in bytes.  The
>  data used by IPMI is 8-bits wide, but it may be inside a larger
> -register.  This parameter allows the read and write type to specified.
> +register.  This parameter allows the read and write type to be specified.
>  It may be 1, 2, 4, or 8.  The default is 1.
>  
>  Since the register size may be larger than 32 bits, the IPMI data may not
> @@ -481,8 +481,8 @@ If your IPMI interface does not support interrupts and is a KCS or
>  SMIC interface, the IPMI driver will start a kernel thread for the
>  interface to help speed things up.  This is a low-priority kernel
>  thread that constantly polls the IPMI driver while an IPMI operation
> -is in progress.  The force_kipmid module parameter will all the user to
> -force this thread on or off.  If you force it off and don't have
> +is in progress.  The force_kipmid module parameter will allow the user
> +to force this thread on or off.  If you force it off and don't have
>  interrupts, the driver will run VERY slowly.  Don't blame me,
>  these interfaces suck.
>  
> @@ -583,7 +583,7 @@ kernel command line as::
>  These are the same options as on the module command line.
>  
>  The I2C driver does not support non-blocking access or polling, so
> -this driver cannod to IPMI panic events, extend the watchdog at panic
> +this driver cannot do IPMI panic events, extend the watchdog at panic
>  time, or other panic-related IPMI functions without special kernel
>  patches and driver modifications.  You can get those at the openipmi
>  web page.
> @@ -610,7 +610,7 @@ Parameters are::
>  	ipmi_ipmb.retry_time_ms=<Time between retries on IPMB>
>  	ipmi_ipmb.max_retries=<Number of times to retry a message>
>  
> -Loading the module will not result in the driver automatcially
> +Loading the module will not result in the driver automatically
>  starting unless there is device tree information setting it up.  If
>  you want to instantiate one of these by hand, do::
>  
> -- 
> 2.39.5
>