From: "Lorenzo Stoakes (ARM)" <ljs@kernel.org>
To: Tal Zussman <tz2294@columbia.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>,
"Liam R. Howlett" <liam@infradead.org>,
David Hildenbrand <david@kernel.org>,
Vlastimil Babka <vbabka@kernel.org>,
Jann Horn <jannh@google.com>, Mike Rapoport <rppt@kernel.org>,
Suren Baghdasaryan <surenb@google.com>,
Michal Hocko <mhocko@suse.com>, Shuah Khan <shuah@kernel.org>,
linux-mm@kvack.org, linux-kernel@vger.kernel.org,
linux-kselftest@vger.kernel.org, stable@vger.kernel.org
Subject: Re: [PATCH v2] mm/madvise: zap markers from guard regions
Date: Tue, 17 Nov 2026 10:29:34 +0000 [thread overview]
Message-ID: <avwsiDm5bM0OCNIg@gremlin> (raw)
In-Reply-To: <8092de9e-3146-4fe7-a235-01ea8efab08c@columbia.edu>
On Tue, Nov 17, 2026 at 01:37:06AM -0500, Tal Zussman wrote:
> On 11/13/26 4:04 PM, Lorenzo Stoakes (ARM) wrote:
> > In order to establish guard regions, guard markers are installed in the
> > page tables of a mapped VMA.
> >
> > However, problems arise when one tries to combine this with registering a
> > VMA for userfaultfd, as such operations may themselves need to install page
> > table markers such as uffd-wp.
> >
> > When the installation is attempted the guard marker prevents these markers
> > being applied, which can lead to unexpected results (especially if the
> > guard regions are later removed.)
> >
> > This is especially problematic because guard region installation causes the
> > regions to be zapped first, meaning that the removal of userfaultfd-tracked
> > ranges will not be logged in this case.
> >
> > Additionally, the uffd-wp page table marker will be propagated regardless
> > for file-backed mappings as the zap being performed does not clear these
> > markers.
> >
> > This is problematic, as it can cause repeated failure to install guard
> > markers resulting in an infinite loop.
> >
> > Therefore, update guard region installation to invoke the zap with the
> > ZAP_FLAG_DROP_MARKER flag applied.
> >
> > Both before and after this change, uffd remove events will not trigger on
> > guard region installation, nor will write protect state be propagated after
> > guard region removal.
> >
> > This makes sense as conceptually, guard regions mark a part of a VMA as
> > effectively unmapped at the page table level, and removing the markers is
> > like mapping the VMA again, over which operation uffd markers would in any
> > case be lost.
> >
> > A survey of open source users indicates nobody is relying on installing
> > guard regions in uffd-armed VMAs. Software including glibc, android,
> > tcmalloc and CRIU were checked.
> >
> > This change means that any already established guard regions are removed on
> > zap. These will be overwritten with the newly installed guard markers on
> > success.
> >
> > However, if this fails for some reason (fatal signal likely the only
> > reasonable cause), guard regions may remain removed, and concurrent faults
> > may succeed in the interim in the range.
> >
> > Since the installation failing guarantees nothing about the range being
> > installed into, and since success overwrites with guard markers, this isn't
> > an issue.
> >
> > Since MADV_DONTNEED does something similar, abstract the zapping to
> > zap_range() and call it from both places.
> >
> Reviewed-by: Tal Zussman <tz2294@columbia.edu>
> Tested-by: Tal Zussman <tz2294@columbia.edu>
Thanks! :)
--
Cheers, Lorenzo
prev parent reply other threads:[~2026-11-17 10:29 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-13 21:04 [PATCH v2] mm/madvise: zap markers from guard regions Lorenzo Stoakes (ARM)
2026-11-13 21:10 ` David Hildenbrand (Arm)
2026-11-13 21:18 ` Lorenzo Stoakes (ARM)
2026-11-13 21:39 ` David Hildenbrand (Arm)
2026-11-13 21:40 ` Lorenzo Stoakes (ARM)
2026-11-13 21:10 ` Lorenzo Stoakes (ARM)
2026-11-16 17:26 ` Liam R. Howlett
2026-11-17 6:37 ` Tal Zussman
2026-11-17 10:29 ` Lorenzo Stoakes (ARM) [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=avwsiDm5bM0OCNIg@gremlin \
--to=ljs@kernel.org \
--cc=akpm@linux-foundation.org \
--cc=david@kernel.org \
--cc=jannh@google.com \
--cc=liam@infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-kselftest@vger.kernel.org \
--cc=linux-mm@kvack.org \
--cc=mhocko@suse.com \
--cc=rppt@kernel.org \
--cc=shuah@kernel.org \
--cc=stable@vger.kernel.org \
--cc=surenb@google.com \
--cc=tz2294@columbia.edu \
--cc=vbabka@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox