Re: [PATCH/RFC v10 09/19] DT: Add documentation for the mfd Maxim max77693

[Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>]

On Tue, 20 Jan 2015, Jacek Anaszewski wrote:

> On 01/20/2015 12:21 PM, Lee Jones wrote:
> >On Fri, 09 Jan 2015, Jacek Anaszewski wrote:
> >
> >>This patch adds device tree binding documentation for
> >>the flash cell of the Maxim max77693 multifunctional device.
> >>
> >>Signed-off-by: Jacek Anaszewski <j.anaszewski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> >>Signed-off-by: Andrzej Hajda <a.hajda-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> >>Acked-by: Kyungmin Park <kyungmin.park-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> >>Cc: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> >>Cc: Chanwoo Choi <cw00.choi-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
> >>Cc: Bryan Wu <cooloney-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> >>Cc: Richard Purdie <rpurdie-Fm38FmjxZ/leoWH0uzbU5w@public.gmane.org>
> >>Cc: Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> >>Cc: Pawel Moll <pawel.moll-5wv7dgnIgG8@public.gmane.org>
> >>Cc: Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>
> >>Cc: Ian Campbell <ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg@public.gmane.org>
> >>Cc: Kumar Gala <galak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
> >>---
> >>  Documentation/devicetree/bindings/mfd/max77693.txt |   69 ++++++++++++++++++++
> >>  1 file changed, 69 insertions(+)
> >>
> >>diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
> >>index 01e9f30..ef184f0 100644
> >>--- a/Documentation/devicetree/bindings/mfd/max77693.txt
> >>+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
> >>@@ -41,7 +41,52 @@ Optional properties:
> >>  	 To get more informations, please refer to documentaion.
> >>  	[*] refer Documentation/devicetree/bindings/pwm/pwm.txt
> >>
> >>+- led : the LED submodule device node
> >>+
> >>+There are two led outputs available - fled1 and fled2. Each of them can
> >>+control a separate led or they can be connected together to double
> >>+the maximum current for a single connected led. One led is represented
> >>+by one child node.
> >>+
> >>+Required properties:
> >>+- compatible : Must be "maxim,max77693-led".
> >>+
> >>+Optional properties:
> >>+- maxim,trigger-type : Flash trigger type.
> >>+	Possible trigger types:
> >>+		MAX77693_LED_TRIG_TYPE_EDGE - Rising edge of the signal triggers
> >>+			the flash,
> >>+		MAX77693_LED_TRIG_TYPE_LEVEL - Strobe pulse length controls
> >>+			duration of the flash.
> >
> >I think you should represent the proper values here instead of the
> >defines.
> 
> I see both versions in the existing bindings and also a combination of
> them, e.g.: MAX77693_LED_TRIG_TYPE_EDGE (0). I think that it is
> reasonable to mention the macros, especially if they are to appear
> in the DT binding example at the end of the documentation file.
> 
> >>+- maxim,boost-mode :
> >>+	In boost mode the device can produce up to 1.2A of total current
> >>+	on both outputs. The maximum current on each output is reduced
> >>+	to 625mA then. If not enabled explicitly, boost setting defaults to
> >>+	MAX77693_LED_BOOST_FIXED in case both current sources are used.
> >>+	Possible values:
> >>+		MAX77693_LED_BOOST_OFF - no boost,
> >>+		MAX77693_LED_BOOST_ADAPTIVE - adaptive mode,
> >>+		MAX77693_LED_BOOST_FIXED - fixed mode.
> >
> >Same here.
> 
> MAX77693_LED_BOOST_OFF (0) - no boost,
> MAX77693_LED_BOOST_ADAPTIVE (1) - adaptive mode,
> MAX77693_LED_BOOST_FIXED (2) - fixed mode.

This is fine too.

> >>+- maxim,boost-vout : Output voltage of the boost module in millivolts.
> >
> >-mvout?
> >-microvout?
> 
> maxim,boost-mvout ?

Right.

> >>+- maxim,vsys-min : Low input voltage level in millivolts. Flash is not fired
> >>+	if chip estimates that system voltage could drop below this level due
> >>+	to flash power consumption.
> >
> >mvsys?
> >microvsys?
> 
> maxim,mvsys-min ?

Looks okay to me.

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html