From: Dan Murphy <dmurphy@ti.com>
To: robh+dt@kernel.org, jacek.anaszewski@gmail.com, pavel@ucw.cz
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
lee.jones@linaro.org, linux-omap@vger.kernel.org,
linux-leds@vger.kernel.org, Dan Murphy <dmurphy@ti.com>
Subject: [RFC PATCH 3/9] mfd: ti-lmu: Remove support for LM3697
Date: Wed, 26 Sep 2018 08:09:15 -0500 [thread overview]
Message-ID: <20180926130921.12329-4-dmurphy@ti.com> (raw)
In-Reply-To: <20180926130921.12329-1-dmurphy@ti.com>
Remove support for the LM3697 from the ti-lmu
driver in favor of a dedicated LED driver.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
drivers/mfd/Kconfig | 2 +-
drivers/mfd/ti-lmu.c | 17 -----------
include/linux/mfd/ti-lmu-register.h | 44 -----------------------------
include/linux/mfd/ti-lmu.h | 1 -
4 files changed, 1 insertion(+), 63 deletions(-)
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 11841f4b7b2b..9b04dd527c68 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1293,7 +1293,7 @@ config MFD_TI_LMU
help
Say yes here to enable support for TI LMU chips.
- TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
+ TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, and LM3695.
It consists of backlight, LED and regulator driver.
It provides consistent device controls for lighting functions.
diff --git a/drivers/mfd/ti-lmu.c b/drivers/mfd/ti-lmu.c
index cfb411cde51c..b6bfa99a29dd 100644
--- a/drivers/mfd/ti-lmu.c
+++ b/drivers/mfd/ti-lmu.c
@@ -128,20 +128,6 @@ static struct mfd_cell lm3695_devices[] = {
},
};
-static struct mfd_cell lm3697_devices[] = {
- {
- .name = "ti-lmu-backlight",
- .id = LM3697,
- .of_compatible = "ti,lm3697-backlight",
- },
- /* Monitoring driver for open/short circuit detection */
- {
- .name = "ti-lmu-fault-monitor",
- .id = LM3697,
- .of_compatible = "ti,lm3697-fault-monitor",
- },
-};
-
#define TI_LMU_DATA(chip, max_reg) \
static const struct ti_lmu_data chip##_data = \
{ \
@@ -155,7 +141,6 @@ TI_LMU_DATA(lm3631, LM3631_MAX_REG);
TI_LMU_DATA(lm3632, LM3632_MAX_REG);
TI_LMU_DATA(lm3633, LM3633_MAX_REG);
TI_LMU_DATA(lm3695, LM3695_MAX_REG);
-TI_LMU_DATA(lm3697, LM3697_MAX_REG);
static const struct of_device_id ti_lmu_of_match[] = {
{ .compatible = "ti,lm3532", .data = &lm3532_data },
@@ -163,7 +148,6 @@ static const struct of_device_id ti_lmu_of_match[] = {
{ .compatible = "ti,lm3632", .data = &lm3632_data },
{ .compatible = "ti,lm3633", .data = &lm3633_data },
{ .compatible = "ti,lm3695", .data = &lm3695_data },
- { .compatible = "ti,lm3697", .data = &lm3697_data },
{ }
};
MODULE_DEVICE_TABLE(of, ti_lmu_of_match);
@@ -237,7 +221,6 @@ static const struct i2c_device_id ti_lmu_ids[] = {
{ "lm3632", LM3632 },
{ "lm3633", LM3633 },
{ "lm3695", LM3695 },
- { "lm3697", LM3697 },
{ }
};
MODULE_DEVICE_TABLE(i2c, ti_lmu_ids);
diff --git a/include/linux/mfd/ti-lmu-register.h b/include/linux/mfd/ti-lmu-register.h
index 2125c7c02818..99711ff4b809 100644
--- a/include/linux/mfd/ti-lmu-register.h
+++ b/include/linux/mfd/ti-lmu-register.h
@@ -233,48 +233,4 @@
#define LM3695_REG_BRT_MSB 0x14
#define LM3695_MAX_REG 0x14
-
-/* LM3697 */
-#define LM3697_REG_HVLED_OUTPUT_CFG 0x10
-#define LM3697_HVLED1_CFG_MASK BIT(0)
-#define LM3697_HVLED2_CFG_MASK BIT(1)
-#define LM3697_HVLED3_CFG_MASK BIT(2)
-#define LM3697_HVLED1_CFG_SHIFT 0
-#define LM3697_HVLED2_CFG_SHIFT 1
-#define LM3697_HVLED3_CFG_SHIFT 2
-
-#define LM3697_REG_BL0_RAMP 0x11
-#define LM3697_REG_BL1_RAMP 0x12
-#define LM3697_RAMPUP_MASK 0xF0
-#define LM3697_RAMPUP_SHIFT 4
-#define LM3697_RAMPDN_MASK 0x0F
-#define LM3697_RAMPDN_SHIFT 0
-
-#define LM3697_REG_RAMP_CONF 0x14
-#define LM3697_RAMP_MASK 0x0F
-#define LM3697_RAMP_EACH 0x05
-
-#define LM3697_REG_PWM_CFG 0x1C
-#define LM3697_PWM_A_MASK BIT(0)
-#define LM3697_PWM_B_MASK BIT(1)
-
-#define LM3697_REG_IMAX_A 0x17
-#define LM3697_REG_IMAX_B 0x18
-
-#define LM3697_REG_FEEDBACK_ENABLE 0x19
-
-#define LM3697_REG_BRT_A_LSB 0x20
-#define LM3697_REG_BRT_A_MSB 0x21
-#define LM3697_REG_BRT_B_LSB 0x22
-#define LM3697_REG_BRT_B_MSB 0x23
-
-#define LM3697_REG_ENABLE 0x24
-
-#define LM3697_REG_OPEN_FAULT_STATUS 0xB0
-
-#define LM3697_REG_SHORT_FAULT_STATUS 0xB2
-
-#define LM3697_REG_MONITOR_ENABLE 0xB4
-
-#define LM3697_MAX_REG 0xB4
#endif
diff --git a/include/linux/mfd/ti-lmu.h b/include/linux/mfd/ti-lmu.h
index 09d5f30384e5..bc9272f08f47 100644
--- a/include/linux/mfd/ti-lmu.h
+++ b/include/linux/mfd/ti-lmu.h
@@ -26,7 +26,6 @@ enum ti_lmu_id {
LM3632,
LM3633,
LM3695,
- LM3697,
LMU_MAX_ID,
};
--
2.19.0
next prev parent reply other threads:[~2018-09-26 13:09 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-09-26 13:09 [RFC PATCH 0/9] TI LMU and Dedicated LED drivers Dan Murphy
2018-09-26 13:09 ` [RFC PATCH 1/9] leds: add TI LMU backlight driver Dan Murphy
2018-09-26 15:01 ` Tony Lindgren
2018-09-26 15:30 ` Dan Murphy
2018-09-26 13:09 ` [RFC PATCH 2/9] dt-bindings: ti-lmu: Remove LM3697 Dan Murphy
2018-09-26 13:09 ` Dan Murphy [this message]
2018-09-26 13:09 ` [RFC PATCH 4/9] dt-bindings: leds: Add bindings for lm3697 driver Dan Murphy
2018-09-26 13:09 ` [RFC PATCH 5/9] leds: lm3697: Introduce the " Dan Murphy
2018-09-26 13:09 ` [RFC PATCH 6/9] dt-bindings: leds: Add support for the LM3633 Dan Murphy
2018-09-26 13:09 ` [RFC PATCH 7/9] leds: lm3633: Introduce the lm3633 driver Dan Murphy
2018-09-26 22:36 ` Pavel Machek
2018-09-27 12:04 ` Dan Murphy
2018-09-27 21:47 ` Pavel Machek
2018-09-28 16:48 ` Dan Murphy
2018-09-26 13:09 ` [RFC PATCH 8/9] dt-bindings: leds: Add the LM3632 LED dt binding Dan Murphy
2018-09-26 13:09 ` [RFC PATCH 9/9] leds: lm3632: Introduce the TI LM3632 driver Dan Murphy
2018-10-07 13:46 ` Pavel Machek
2018-10-08 12:23 ` Dan Murphy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180926130921.12329-4-dmurphy@ti.com \
--to=dmurphy@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=jacek.anaszewski@gmail.com \
--cc=lee.jones@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=pavel@ucw.cz \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).