[PATCH v2 1/6] regulator: lm363x: Make the gpio register enable flexible

[PATCH v2 1/6] regulator: lm363x: Make the gpio register enable flexible

[Dan Murphy]

The use of and enablement of the GPIO can be used across devices.
Use the enable_reg in the regulator descriptor for the register to
write.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---

v2 - No changes - https://lore.kernel.org/patchwork/patch/1058777/

 drivers/regulator/lm363x-regulator.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/regulator/lm363x-regulator.c b/drivers/regulator/lm363x-regulator.c
index c876e161052a..382b1cecdd93 100644
--- a/drivers/regulator/lm363x-regulator.c
+++ b/drivers/regulator/lm363x-regulator.c
@@ -263,8 +263,8 @@ static int lm363x_regulator_probe(struct platform_device *pdev)
 
 	if (gpiod) {
 		cfg.ena_gpiod = gpiod;
-
-		ret = regmap_update_bits(regmap, LM3632_REG_BIAS_CONFIG,
+		ret = regmap_update_bits(regmap,
+					 lm363x_regulator_desc[id].enable_reg,
 					 LM3632_EXT_EN_MASK,
 					 LM3632_EXT_EN_MASK);
 		if (ret) {
-- 
2.21.0.5.gaeb582a983

[PATCH v2 2/6] dt-bindings: mfd: Add lm36274 bindings to ti-lmu

[Dan Murphy]

Add the LM36274 backlight driver with regulator support.
This is a multi-function device for backlight applications.

Backlight properties will be documented in it's a supplemental
bindings document.

Regulator support is documented in the regulator/lm363x-regulator.txt

http://www.ti.com/lit/ds/symlink/lm36274.pdf

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---

v2 - No changes - https://lore.kernel.org/patchwork/patch/1058776/

 .../devicetree/bindings/mfd/ti-lmu.txt        | 54 +++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
index a948a8f41b2c..6ada671c1038 100644
--- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt
+++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
@@ -8,6 +8,7 @@ TI LMU driver supports lighting devices below.
   LM3632       Backlight and regulator
   LM3633       Backlight, LED and fault monitor
   LM3695       Backlight
+  LM36274      Backlight and regulator
 
 Required properties:
   - compatible: Should be one of:
@@ -15,11 +16,13 @@ Required properties:
                 "ti,lm3632"
                 "ti,lm3633"
                 "ti,lm3695"
+		"ti,lm36274"
   - reg: I2C slave address.
          0x11 for LM3632
          0x29 for LM3631
          0x36 for LM3633
          0x63 for LM3695
+         0x11 for LM36274
 
 Optional property:
   - enable-gpios: A GPIO specifier for hardware enable pin.
@@ -50,12 +53,14 @@ Optional nodes:
       - compatible: Should be one of:
                     "ti,lm3633-fault-monitor"
   - leds: LED properties for LM3633. Please refer to [2].
+	  LED properties for LM36274. Please refer to [4].
   - regulators: Regulator properties for LM3631 and LM3632.
                 Please refer to [3].
 
 [1] ../leds/backlight/ti-lmu-backlight.txt
 [2] ../leds/leds-lm3633.txt
 [3] ../regulator/lm363x-regulator.txt
+[4] ../leds/leds-lm36274.txt
 
 lm3631@29 {
 	compatible = "ti,lm3631";
@@ -213,3 +218,52 @@ lm3695@63 {
 		};
 	};
 };
+
+lm36274@11 {
+	compatible = "ti,lm36274";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x11>;
+
+	enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
+	regulators {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm363x-regulator";
+
+		enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,
+			       <&pioC 1 GPIO_ACTIVE_HIGH>;
+
+		vboost {
+			regulator-name = "lcd_boost";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <7150000>;
+			regulator-always-on;
+		};
+
+		vpos {
+			regulator-name = "lcd_vpos";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
+		};
+
+		vneg {
+			regulator-name = "lcd_vneg";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
+		};
+	};
+
+	backlight {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm36274-backlight";
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 2>;
+			label = "white:backlight_cluster";
+			linux,default-trigger = "backlight";
+		};
+	};
+};
-- 
2.21.0.5.gaeb582a983

Re: [PATCH v2 2/6] dt-bindings: mfd: Add lm36274 bindings to ti-lmu

[Rob Herring]

On Wed, 10 Apr 2019 08:38:29 -0500, Dan Murphy wrote:
> Add the LM36274 backlight driver with regulator support.
> This is a multi-function device for backlight applications.
> 
> Backlight properties will be documented in it's a supplemental
> bindings document.
> 
> Regulator support is documented in the regulator/lm363x-regulator.txt
> 
> http://www.ti.com/lit/ds/symlink/lm36274.pdf
> 
> Signed-off-by: Dan Murphy <dmurphy@ti.com>
> ---
> 
> v2 - No changes - https://lore.kernel.org/patchwork/patch/1058776/
> 
>  .../devicetree/bindings/mfd/ti-lmu.txt        | 54 +++++++++++++++++++
>  1 file changed, 54 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v2 3/6] mfd: ti-lmu: Add LM36274 support to the ti-lmu

[Dan Murphy]

Add the LM36274 register support to the ti-lmu MFD driver.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---

v2 - No changes - https://lore.kernel.org/patchwork/patch/1058780/

 drivers/mfd/Kconfig                 |  5 ++---
 drivers/mfd/ti-lmu.c                | 14 ++++++++++++++
 include/linux/mfd/ti-lmu-register.h | 23 +++++++++++++++++++++++
 include/linux/mfd/ti-lmu.h          |  4 ++++
 4 files changed, 43 insertions(+), 3 deletions(-)

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index fcae244229b3..5606411038bb 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1311,9 +1311,8 @@ config MFD_TI_LMU
 	select REGMAP_I2C
 	help
 	  Say yes here to enable support for TI LMU chips.
-
-	  TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, and LM3695.
-	  It consists of backlight, LED and regulator driver.
+	  TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and
+	  LM36274.  It consists of backlight, LED and regulator driver.
 	  It provides consistent device controls for lighting functions.
 
 config MFD_OMAP_USB_HOST
diff --git a/drivers/mfd/ti-lmu.c b/drivers/mfd/ti-lmu.c
index 89b1c5b584af..691ab9dd6236 100644
--- a/drivers/mfd/ti-lmu.c
+++ b/drivers/mfd/ti-lmu.c
@@ -111,6 +111,17 @@ static const struct mfd_cell lm3695_devices[] = {
 	},
 };
 
+static const struct mfd_cell lm36274_devices[] = {
+	LM363X_REGULATOR(LM36274_BOOST),
+	LM363X_REGULATOR(LM36274_LDO_POS),
+	LM363X_REGULATOR(LM36274_LDO_NEG),
+	{
+		.name          = "lm36274-leds",
+		.id            = LM36274,
+		.of_compatible = "ti,lm36274-backlight",
+	},
+};
+
 #define TI_LMU_DATA(chip, max_reg)		\
 static const struct ti_lmu_data chip##_data =	\
 {						\
@@ -123,6 +134,7 @@ TI_LMU_DATA(lm3631, LM3631_MAX_REG);
 TI_LMU_DATA(lm3632, LM3632_MAX_REG);
 TI_LMU_DATA(lm3633, LM3633_MAX_REG);
 TI_LMU_DATA(lm3695, LM3695_MAX_REG);
+TI_LMU_DATA(lm36274, LM36274_MAX_REG);
 
 static int ti_lmu_probe(struct i2c_client *cl, const struct i2c_device_id *id)
 {
@@ -191,6 +203,7 @@ static const struct of_device_id ti_lmu_of_match[] = {
 	{ .compatible = "ti,lm3632", .data = &lm3632_data },
 	{ .compatible = "ti,lm3633", .data = &lm3633_data },
 	{ .compatible = "ti,lm3695", .data = &lm3695_data },
+	{ .compatible = "ti,lm36274", .data = &lm36274_data },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, ti_lmu_of_match);
@@ -200,6 +213,7 @@ static const struct i2c_device_id ti_lmu_ids[] = {
 	{ "lm3632", LM3632 },
 	{ "lm3633", LM3633 },
 	{ "lm3695", LM3695 },
+	{ "lm36274", LM36274 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, ti_lmu_ids);
diff --git a/include/linux/mfd/ti-lmu-register.h b/include/linux/mfd/ti-lmu-register.h
index 76998b01764b..076d8dea38fd 100644
--- a/include/linux/mfd/ti-lmu-register.h
+++ b/include/linux/mfd/ti-lmu-register.h
@@ -189,4 +189,27 @@
 #define LM3695_REG_BRT_MSB			0x14
 
 #define LM3695_MAX_REG				0x14
+
+/* LM36274 */
+#define LM36274_REG_REV				0x01
+#define LM36274_REG_BL_CFG_1			0x02
+#define LM36274_REG_BL_CFG_2			0x03
+#define LM36274_REG_BRT_LSB			0x04
+#define LM36274_REG_BRT_MSB			0x05
+#define LM36274_REG_BL_EN			0x08
+
+#define LM36274_REG_BIAS_CONFIG_1		0x09
+#define LM36274_EXT_EN_MASK			BIT(0)
+#define LM36274_EN_VNEG_MASK			BIT(1)
+#define LM36274_EN_VPOS_MASK			BIT(2)
+
+#define LM36274_REG_BIAS_CONFIG_2		0x0a
+#define LM36274_REG_BIAS_CONFIG_3		0x0b
+#define LM36274_REG_VOUT_BOOST			0x0c
+#define LM36274_REG_VOUT_POS			0x0d
+#define LM36274_REG_VOUT_NEG			0x0e
+#define LM36274_VOUT_MASK			0x3F
+
+#define LM36274_MAX_REG				0x13
+
 #endif
diff --git a/include/linux/mfd/ti-lmu.h b/include/linux/mfd/ti-lmu.h
index 54e9d272e81c..0957598c7d41 100644
--- a/include/linux/mfd/ti-lmu.h
+++ b/include/linux/mfd/ti-lmu.h
@@ -26,6 +26,7 @@ enum ti_lmu_id {
 	LM3632,
 	LM3633,
 	LM3695,
+	LM36274,
 	LMU_MAX_ID,
 };
 
@@ -67,6 +68,9 @@ enum lm363x_regulator_id {
 	LM3632_BOOST,		/* Boost output */
 	LM3632_LDO_POS,		/* Positive display bias output */
 	LM3632_LDO_NEG,		/* Negative display bias output */
+	LM36274_BOOST,		/* Boost output */
+	LM36274_LDO_POS,	/* Positive display bias output */
+	LM36274_LDO_NEG,	/* Negative display bias output */
 };
 
 /**
-- 
2.21.0.5.gaeb582a983

[PATCH v2 4/6] regulator: lm363x: Add support for LM36274

[Dan Murphy]

Adding regulator support for the LM36274 backlight driver.
This device can leverage this existing code as the functionality
and registers are common enough between the LM36274 and the LM363x
series of devices.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---

v2 - No changes - https://lore.kernel.org/patchwork/patch/1058781/

 drivers/regulator/Kconfig            |  2 +-
 drivers/regulator/lm363x-regulator.c | 52 ++++++++++++++++++++++++++++
 2 files changed, 53 insertions(+), 1 deletion(-)

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index b7f249ee5e68..23252ae81fdf 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -362,7 +362,7 @@ config REGULATOR_LM363X
 	tristate "TI LM363X voltage regulators"
 	depends on MFD_TI_LMU
 	help
-	  This driver supports LM3631 and LM3632 voltage regulators for
+	  This driver supports LM3631, LM3632 and LM36274 voltage regulators for
 	  the LCD bias.
 	  One boost output voltage is configurable and always on.
 	  Other LDOs are used for the display module.
diff --git a/drivers/regulator/lm363x-regulator.c b/drivers/regulator/lm363x-regulator.c
index 382b1cecdd93..1944677b1448 100644
--- a/drivers/regulator/lm363x-regulator.c
+++ b/drivers/regulator/lm363x-regulator.c
@@ -37,6 +37,11 @@
 #define LM3632_VBOOST_MIN		4500000
 #define LM3632_VLDO_MIN			4000000
 
+/* LM36274 */
+#define LM36274_BOOST_VSEL_MAX		0x3f
+#define LM36274_LDO_VSEL_MAX		0x34
+#define LM36274_VOLTAGE_MIN		4000000
+
 /* Common */
 #define LM363X_STEP_50mV		50000
 #define LM363X_STEP_500mV		500000
@@ -217,6 +222,51 @@ static const struct regulator_desc lm363x_regulator_desc[] = {
 		.enable_reg     = LM3632_REG_BIAS_CONFIG,
 		.enable_mask    = LM3632_EN_VNEG_MASK,
 	},
+
+	/* LM36274 */
+	{
+		.name           = "vboost",
+		.of_match	= "vboost",
+		.id             = LM36274_BOOST,
+		.ops            = &lm363x_boost_voltage_table_ops,
+		.n_voltages     = LM36274_BOOST_VSEL_MAX,
+		.min_uV         = LM36274_VOLTAGE_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM36274_REG_VOUT_BOOST,
+		.vsel_mask      = LM36274_VOUT_MASK,
+	},
+	{
+		.name           = "ldo_vpos",
+		.of_match	= "vpos",
+		.id             = LM36274_LDO_POS,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM36274_LDO_VSEL_MAX,
+		.min_uV         = LM36274_VOLTAGE_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM36274_REG_VOUT_POS,
+		.vsel_mask      = LM36274_VOUT_MASK,
+		.enable_reg     = LM36274_REG_BIAS_CONFIG_1,
+		.enable_mask    = LM36274_EN_VPOS_MASK,
+	},
+	{
+		.name           = "ldo_vneg",
+		.of_match	= "vneg",
+		.id             = LM36274_LDO_NEG,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM36274_LDO_VSEL_MAX,
+		.min_uV         = LM36274_VOLTAGE_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM36274_REG_VOUT_NEG,
+		.vsel_mask      = LM36274_VOUT_MASK,
+		.enable_reg     = LM36274_REG_BIAS_CONFIG_1,
+		.enable_mask    = LM36274_EN_VNEG_MASK,
+	},
 };
 
 static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev, int id)
@@ -229,9 +279,11 @@ static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev,
 	 */
 	switch (id) {
 	case LM3632_LDO_POS:
+	case LM36274_LDO_POS:
 		return gpiod_get_index_optional(dev, "enable", 0,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	case LM3632_LDO_NEG:
+	case LM36274_LDO_NEG:
 		return gpiod_get_index_optional(dev, "enable", 1,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	default:
-- 
2.21.0.5.gaeb582a983

[PATCH v2 5/6] dt-bindings: leds: Add LED bindings for the LM36274

[Dan Murphy]

Add the LM36274 LED specific bindings.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---

v2 - Changed 29-V to 29V - https://lore.kernel.org/patchwork/patch/1058779/

 .../devicetree/bindings/leds/leds-lm36274.txt | 82 +++++++++++++++++++
 1 file changed, 82 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/leds-lm36274.txt

diff --git a/Documentation/devicetree/bindings/leds/leds-lm36274.txt b/Documentation/devicetree/bindings/leds/leds-lm36274.txt
new file mode 100644
index 000000000000..329393700191
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-lm36274.txt
@@ -0,0 +1,82 @@
+* Texas Instruments LM36274 4-Channel LCD Backlight Driver w/Integrated Bias
+
+The LM36274 is an integrated four-channel WLED driver and LCD bias supply.
+The backlight boost provides the power to bias four parallel LED strings with
+up to 29V total output voltage. The 11-bit LED current is programmable via
+the I2C bus and/or controlled via a logic level PWM input from 60 μA to 30 mA.
+
+Parent device properties are documented in ../mfd/ti_lmu.txt
+Regulator properties are documented in ../regulator/lm363x-regulator.txt
+
+Required backlight properties:
+	- compatible:
+		"ti,lm36274-backlight"
+	- reg : 0
+	- #address-cells : 1
+	- #size-cells : 0
+	- led-sources : Indicates which LED strings will be enabled.
+			Values from 0-3, sources is 0 based so strings will be
+			source value + 1.
+
+Optional backlight properties:
+	- label : see Documentation/devicetree/bindings/leds/common.txt
+	- linux,default-trigger :
+	   see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is
+controlled by control bank B.
+
+lm36274@11 {
+	compatible = "ti,lm36274";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x11>;
+
+	enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+
+	regulators {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm363x-regulator";
+
+		enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>,
+			       <&pioC 1 GPIO_ACTIVE_HIGH>;
+
+		vboost {
+			regulator-name = "lcd_boost";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <7150000>;
+			regulator-always-on;
+		};
+
+		vpos {
+			regulator-name = "lcd_vpos";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
+		};
+
+		vneg {
+			regulator-name = "lcd_vneg";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6500000>;
+		};
+	};
+
+	backlight {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "ti,lm36274-backlight";
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 2>;
+			label = "white:backlight_cluster";
+			linux,default-trigger = "backlight";
+		};
+	};
+};
+
+For more product information please see the link below:
+http://www.ti.com/lit/ds/symlink/lm36274.pdf
-- 
2.21.0.5.gaeb582a983

Re: [PATCH v2 5/6] dt-bindings: leds: Add LED bindings for the LM36274

[Rob Herring]

On Wed, 10 Apr 2019 08:38:32 -0500, Dan Murphy wrote:
> Add the LM36274 LED specific bindings.
> 
> Signed-off-by: Dan Murphy <dmurphy@ti.com>
> ---
> 
> v2 - Changed 29-V to 29V - https://lore.kernel.org/patchwork/patch/1058779/
> 
>  .../devicetree/bindings/leds/leds-lm36274.txt | 82 +++++++++++++++++++
>  1 file changed, 82 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/leds-lm36274.txt
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v2 6/6] leds: lm36274: Introduce the TI LM36274 LED driver

[Dan Murphy]

Introduce the LM36274 LED driver.  This driver uses the ti-lmu
MFD driver to probe this LED driver.  The driver configures only the
LED registers and enables the outputs according to the config file.

The driver utilizes the ti-lmu-led-common framework to set the brightness
bits.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---

v2 - No changes - https://lore.kernel.org/patchwork/patch/1058778/

 drivers/leds/Kconfig        |   9 +-
 drivers/leds/Makefile       |   1 +
 drivers/leds/leds-lm36274.c | 174 ++++++++++++++++++++++++++++++++++++
 3 files changed, 183 insertions(+), 1 deletion(-)
 create mode 100644 drivers/leds/leds-lm36274.c

diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 2d1576f4d5d6..c0bf59544886 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -783,12 +783,19 @@ config LEDS_LM3697
 	  Say Y to enable the LM3697 LED driver for TI LMU devices.
 	  This supports the LED device LM3697.
 
+config LEDS_LM36274
+	tristate "LED driver for LM36274"
+	depends on LEDS_TI_LMU_COMMON
+	help
+	  Say Y to enable the LM36274 LED driver for TI LMU devices.
+	  This supports the LED device LM36274.
+
 config LEDS_TI_LMU_COMMON
 	tristate "LED driver for TI LMU"
 	help
           Say Y to enable the LED driver for TI LMU devices.
           This supports common features between the TI LM3532, LM3631, LM3632,
-	  LM3633, LM3695 and LM3697.
+	  LM3633, LM3695, LM3697 and LM36274
 
 comment "LED Triggers"
 source "drivers/leds/trigger/Kconfig"
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index 2eb0225d8dc6..7ff67215b38c 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -81,6 +81,7 @@ obj-$(CONFIG_LEDS_LM3692X)		+= leds-lm3692x.o
 obj-$(CONFIG_LEDS_SC27XX_BLTC)		+= leds-sc27xx-bltc.o
 obj-$(CONFIG_LEDS_LM3601X)		+= leds-lm3601x.o
 obj-$(CONFIG_LEDS_LM3697)		+= leds-lm3697.o
+obj-$(CONFIG_LEDS_LM36274)		+= leds-lm36274.o
 obj-$(CONFIG_LEDS_TI_LMU_COMMON)	+= ti-lmu-led-common.o
 
 # LED SPI Drivers
diff --git a/drivers/leds/leds-lm36274.c b/drivers/leds/leds-lm36274.c
new file mode 100644
index 000000000000..6a419c47c47f
--- /dev/null
+++ b/drivers/leds/leds-lm36274.c
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: GPL-2.0
+// TI LM36274 LED chip family driver
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/leds.h>
+#include <linux/ti-lmu-led-common.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+#include <linux/mfd/ti-lmu.h>
+#include <linux/mfd/ti-lmu-register.h>
+
+#include <uapi/linux/uleds.h>
+
+#define LM36274_MAX_STRINGS	4
+#define LM36274_BL_EN		BIT(4)
+
+/**
+ * struct lm36274
+ * @pdev: platform device
+ * @led_dev: led class device
+ * @lmu_data: Register and setting values for common code
+ * @regmap: Devices register map
+ * @dev: Pointer to the devices device struct
+ * @led_sources - The LED strings supported in this array
+ * @num_leds - Number of LED strings are supported in this array
+ */
+struct lm36274 {
+	struct platform_device *pdev;
+	struct led_classdev led_dev;
+	struct ti_lmu_bank lmu_data;
+	struct regmap *regmap;
+	struct device *dev;
+
+	u32 led_sources[LM36274_MAX_STRINGS];
+	int num_leds;
+};
+
+static int lm36274_brightness_set(struct led_classdev *led_cdev,
+				enum led_brightness brt_val)
+{
+	struct lm36274 *led = container_of(led_cdev, struct lm36274, led_dev);
+
+	return ti_lmu_common_set_brightness(&led->lmu_data, brt_val);
+}
+
+static int lm36274_init(struct lm36274 *lm36274_data)
+{
+	int enable_val = 0;
+	int i;
+
+	for (i = 0; i < lm36274_data->num_leds; i++)
+		enable_val |= (1 << lm36274_data->led_sources[i]);
+
+	if (!enable_val) {
+		dev_err(lm36274_data->dev, "No LEDs were enabled\n");
+		return -EINVAL;
+	}
+
+	enable_val |= LM36274_BL_EN;
+
+	return regmap_write(lm36274_data->regmap, LM36274_REG_BL_EN,
+			    enable_val);
+}
+
+static int lm36274_parse_dt(struct lm36274 *lm36274_data)
+{
+	struct fwnode_handle *child = NULL;
+	char label[LED_MAX_NAME_SIZE];
+	struct device *dev = &lm36274_data->pdev->dev;
+	const char *name;
+	int child_cnt;
+	int ret = -EINVAL;
+
+	/* There should only be 1 node */
+	child_cnt = device_get_child_node_count(dev);
+	if (child_cnt != 1)
+		return ret;
+
+	device_for_each_child_node(dev, child) {
+		ret = fwnode_property_read_string(child, "label", &name);
+		if (ret)
+			snprintf(label, sizeof(label),
+				"%s::", lm36274_data->pdev->name);
+		else
+			snprintf(label, sizeof(label),
+				 "%s:%s", lm36274_data->pdev->name, name);
+
+		lm36274_data->num_leds = fwnode_property_read_u32_array(child,
+							  "led-sources",
+							  NULL, 0);
+		if (lm36274_data->num_leds <= 0)
+			return -ENODEV;
+
+		ret = fwnode_property_read_u32_array(child, "led-sources",
+						     lm36274_data->led_sources,
+						     lm36274_data->num_leds);
+		if (ret) {
+			dev_err(dev, "led-sources property missing\n");
+			return -EINVAL;
+		}
+
+		fwnode_property_read_string(child, "linux,default-trigger",
+					&lm36274_data->led_dev.default_trigger);
+
+	}
+
+	lm36274_data->lmu_data.regmap = lm36274_data->regmap;
+	lm36274_data->lmu_data.max_brightness = MAX_BRIGHTNESS_11BIT;
+	lm36274_data->lmu_data.msb_brightness_reg = LM36274_REG_BRT_MSB;
+	lm36274_data->lmu_data.lsb_brightness_reg = LM36274_REG_BRT_LSB;
+
+	lm36274_data->led_dev.name = label;
+	lm36274_data->led_dev.max_brightness = MAX_BRIGHTNESS_11BIT;
+	lm36274_data->led_dev.brightness_set_blocking = lm36274_brightness_set;
+
+	return ret;
+}
+
+static int lm36274_probe(struct platform_device *pdev)
+{
+	struct ti_lmu *lmu = dev_get_drvdata(pdev->dev.parent);
+	struct lm36274 *lm36274_data;
+	int ret;
+
+	lm36274_data = devm_kzalloc(&pdev->dev, sizeof(*lm36274_data),
+				    GFP_KERNEL);
+	if (!lm36274_data) {
+		ret = -ENOMEM;
+		return ret;
+	}
+
+	lm36274_data->pdev = pdev;
+	lm36274_data->dev = lmu->dev;
+	lm36274_data->regmap = lmu->regmap;
+	dev_set_drvdata(&pdev->dev, lm36274_data);
+
+	ret = lm36274_parse_dt(lm36274_data);
+	if (ret) {
+		dev_err(lm36274_data->dev, "Failed to parse DT node\n");
+		return ret;
+	}
+
+	ret = lm36274_init(lm36274_data);
+	if (ret) {
+		dev_err(lm36274_data->dev, "Failed to init the device\n");
+		return ret;
+	}
+
+	return devm_led_classdev_register(lm36274_data->dev,
+					 &lm36274_data->led_dev);
+}
+
+static const struct of_device_id of_lm36274_leds_match[] = {
+	{ .compatible = "ti,lm36274-backlight", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, of_lm36274_leds_match);
+
+static struct platform_driver lm36274_driver = {
+	.probe  = lm36274_probe,
+	.driver = {
+		.name = "lm36274-leds",
+	},
+};
+module_platform_driver(lm36274_driver)
+
+MODULE_DESCRIPTION("Texas Instruments LM36274 LED driver");
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.21.0.5.gaeb582a983