From: Richard Leitner <richard.leitner@linux.dev>
To: Sakari Ailus <sakari.ailus@linux.intel.com>,
Dave Stevenson <dave.stevenson@raspberrypi.com>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Lee Jones <lee@kernel.org>, Pavel Machek <pavel@kernel.org>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>,
linux-media@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-leds@vger.kernel.org,
Richard Leitner <richard.leitner@linux.dev>
Subject: [PATCH v6 06/11] media: i2c: ov9282: add output enable register definitions
Date: Wed, 16 Jul 2025 11:06:56 +0200 [thread overview]
Message-ID: <20250716-ov9282-flash-strobe-v6-6-934f12aeff33@linux.dev> (raw)
In-Reply-To: <20250716-ov9282-flash-strobe-v6-0-934f12aeff33@linux.dev>
Add #define's for the output enable registers (0x3004, 0x3005, 0x3006),
also known as SC_CTRL_04, SC_CTRL_05, SC_CTRL_04. Use those register
definitions instead of the raw values in the `common_regs` struct.
All values are based on the OV9281 datasheet v1.53 (january 2019).
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
---
drivers/media/i2c/ov9282.c | 29 ++++++++++++++++++++++++++---
1 file changed, 26 insertions(+), 3 deletions(-)
diff --git a/drivers/media/i2c/ov9282.c b/drivers/media/i2c/ov9282.c
index c882a021cf18852237bf9b9524d3de0c5b48cbcb..f42e0d439753e74d14e3a3592029e48f49234927 100644
--- a/drivers/media/i2c/ov9282.c
+++ b/drivers/media/i2c/ov9282.c
@@ -37,6 +37,29 @@
#define OV9282_REG_ID 0x300a
#define OV9282_ID 0x9281
+/* Output enable registers */
+#define OV9282_REG_OUTPUT_ENABLE4 0x3004
+#define OV9282_OUTPUT_ENABLE4_GPIO2 BIT(1)
+#define OV9282_OUTPUT_ENABLE4_D9 BIT(0)
+
+#define OV9282_REG_OUTPUT_ENABLE5 0x3005
+#define OV9282_OUTPUT_ENABLE5_D8 BIT(7)
+#define OV9282_OUTPUT_ENABLE5_D7 BIT(6)
+#define OV9282_OUTPUT_ENABLE5_D6 BIT(5)
+#define OV9282_OUTPUT_ENABLE5_D5 BIT(4)
+#define OV9282_OUTPUT_ENABLE5_D4 BIT(3)
+#define OV9282_OUTPUT_ENABLE5_D3 BIT(2)
+#define OV9282_OUTPUT_ENABLE5_D2 BIT(1)
+#define OV9282_OUTPUT_ENABLE5_D1 BIT(0)
+
+#define OV9282_REG_OUTPUT_ENABLE6 0x3006
+#define OV9282_OUTPUT_ENABLE6_D0 BIT(7)
+#define OV9282_OUTPUT_ENABLE6_PCLK BIT(6)
+#define OV9282_OUTPUT_ENABLE6_HREF BIT(5)
+#define OV9282_OUTPUT_ENABLE6_STROBE BIT(3)
+#define OV9282_OUTPUT_ENABLE6_ILPWM BIT(2)
+#define OV9282_OUTPUT_ENABLE6_VSYNC BIT(1)
+
/* Exposure control */
#define OV9282_REG_EXPOSURE 0x3500
#define OV9282_EXPOSURE_MIN 1
@@ -213,9 +236,9 @@ static const struct ov9282_reg common_regs[] = {
{0x0302, 0x32},
{0x030e, 0x02},
{0x3001, 0x00},
- {0x3004, 0x00},
- {0x3005, 0x00},
- {0x3006, 0x04},
+ {OV9282_REG_OUTPUT_ENABLE4, 0x00},
+ {OV9282_REG_OUTPUT_ENABLE5, 0x00},
+ {OV9282_REG_OUTPUT_ENABLE6, OV9282_OUTPUT_ENABLE6_ILPWM},
{0x3011, 0x0a},
{0x3013, 0x18},
{0x301c, 0xf0},
--
2.47.2
next prev parent reply other threads:[~2025-07-16 9:07 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-07-16 9:06 [PATCH v6 00/11] Add strobe duration and hw strobe signal v4l2 ctrl & use it for ov9282 Richard Leitner
2025-07-16 9:06 ` [PATCH v6 01/11] media: v4l: ctrls: add a control for flash/strobe duration Richard Leitner
2025-07-16 9:06 ` [PATCH v6 02/11] media: v4l2-flash: add support " Richard Leitner
2025-07-16 9:06 ` [PATCH v6 03/11] Documentation: uAPI: media: add V4L2_CID_FLASH_DURATION Richard Leitner
2025-08-25 5:42 ` Sakari Ailus
2025-08-25 5:48 ` Sakari Ailus
2025-08-25 18:45 ` Richard Leitner
2025-09-01 10:44 ` Richard Leitner
2025-09-01 12:11 ` Sakari Ailus
2025-07-16 9:06 ` [PATCH v6 04/11] media: v4l: ctrls: add a control for enabling hw strobe signal Richard Leitner
2025-07-16 9:06 ` [PATCH v6 05/11] Documentation: uAPI: media: add V4L2_CID_FLASH_HW_STROBE_SIGNAL Richard Leitner
2025-07-16 9:06 ` Richard Leitner [this message]
2025-07-16 9:06 ` [PATCH v6 07/11] media: i2c: ov9282: add hardware strobe signal v4l2 control Richard Leitner
2025-07-16 9:06 ` [PATCH v6 08/11] media: i2c: ov9282: add strobe_duration " Richard Leitner
2025-07-16 9:06 ` [PATCH v6 09/11] media: i2c: ov9282: add strobe_source " Richard Leitner
2025-07-16 9:07 ` [PATCH v6 10/11] media: i2c: ov9282: implement try_ctrl for strobe_duration Richard Leitner
2025-07-17 8:53 ` kernel test robot
2025-07-16 9:07 ` [PATCH v6 11/11] media: i2c: ov9282: dynamic flash_duration maximum Richard Leitner
2025-08-24 19:03 ` [PATCH v6 00/11] Add strobe duration and hw strobe signal v4l2 ctrl & use it for ov9282 Richard Leitner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250716-ov9282-flash-strobe-v6-6-934f12aeff33@linux.dev \
--to=richard.leitner@linux.dev \
--cc=dave.stevenson@raspberrypi.com \
--cc=hverkuil@xs4all.nl \
--cc=laurent.pinchart@ideasonboard.com \
--cc=lee@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=pavel@kernel.org \
--cc=sakari.ailus@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).