From: Dan Scally <dan.scally@ideasonboard.com>
To: Kate Hsuan <hpa@redhat.com>, Pavel Machek <pavel@ucw.cz>,
Lee Jones <lee@kernel.org>,
linux-leds@vger.kernel.org, platform-driver-x86@vger.kernel.org,
Hans de Goede <hdegoede@redhat.com>,
Daniel Scally <djrscally@gmail.com>,
Mark Gross <markgross@kernel.org>
Subject: Re: [PATCH v3 3/3] leds: tps68470: Add LED control for tps68470
Date: Thu, 23 Mar 2023 07:36:08 +0000 [thread overview]
Message-ID: <aac749fa-3f33-6fb3-cfea-e7a11fd1d384@ideasonboard.com> (raw)
In-Reply-To: <20230321153718.1355511-4-hpa@redhat.com>
Hi Kate
On 21/03/2023 15:37, Kate Hsuan wrote:
> There are two LED controllers, LEDA indicator LED and LEDB flash LED for
> tps68470. LEDA can be enabled by setting TPS68470_ILEDCTL_ENA. Moreover,
> tps68470 provides four levels of power status for LEDB. If the
> properties called "ti,ledb-current" can be found, the current will be
> set according to the property values. These two LEDs can be controlled
> through the LED class of sysfs (tps68470-leda and tps68470-ledb).
>
> Signed-off-by: Kate Hsuan <hpa@redhat.com>
> ---
This looks good to me now: Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
> drivers/leds/Kconfig | 12 +++
> drivers/leds/Makefile | 1 +
> drivers/leds/leds-tps68470.c | 185 +++++++++++++++++++++++++++++++++++
> 3 files changed, 198 insertions(+)
> create mode 100644 drivers/leds/leds-tps68470.c
>
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index 9dbce09eabac..ab9073b2cfef 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -827,6 +827,18 @@ config LEDS_TPS6105X
> It is a single boost converter primarily for white LEDs and
> audio amplifiers.
>
> +config LEDS_TPS68470
> + tristate "LED support for TI TPS68470"
> + depends on LEDS_CLASS
> + depends on INTEL_SKL_INT3472
> + help
> + This driver supports TPS68470 PMIC with LED chip.
> + It provides two LED controllers, with the ability to drive 2
> + indicator LEDs and 2 flash LEDs.
> +
> + To compile this driver as a module, choose M and it will be
> + called leds-tps68470
> +
> config LEDS_IP30
> tristate "LED support for SGI Octane machines"
> depends on LEDS_CLASS
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index d30395d11fd8..515a69953e73 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -80,6 +80,7 @@ obj-$(CONFIG_LEDS_TCA6507) += leds-tca6507.o
> obj-$(CONFIG_LEDS_TI_LMU_COMMON) += leds-ti-lmu-common.o
> obj-$(CONFIG_LEDS_TLC591XX) += leds-tlc591xx.o
> obj-$(CONFIG_LEDS_TPS6105X) += leds-tps6105x.o
> +obj-$(CONFIG_LEDS_TPS68470) += leds-tps68470.o
> obj-$(CONFIG_LEDS_TURRIS_OMNIA) += leds-turris-omnia.o
> obj-$(CONFIG_LEDS_WM831X_STATUS) += leds-wm831x-status.o
> obj-$(CONFIG_LEDS_WM8350) += leds-wm8350.o
> diff --git a/drivers/leds/leds-tps68470.c b/drivers/leds/leds-tps68470.c
> new file mode 100644
> index 000000000000..35aeb5db89c8
> --- /dev/null
> +++ b/drivers/leds/leds-tps68470.c
> @@ -0,0 +1,185 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * LED driver for TPS68470 PMIC
> + *
> + * Copyright (C) 2023 Red Hat
> + *
> + * Authors:
> + * Kate Hsuan <hpa@redhat.com>
> + */
> +
> +#include <linux/leds.h>
> +#include <linux/mfd/tps68470.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +
> +
> +#define lcdev_to_led(led_cdev) \
> + container_of(led_cdev, struct tps68470_led, lcdev)
> +
> +#define led_to_tps68470(led, index) \
> + container_of(led, struct tps68470_device, leds[index])
> +
> +enum tps68470_led_ids {
> + TPS68470_ILED_A,
> + TPS68470_ILED_B,
> + TPS68470_NUM_LEDS
> +};
> +
> +static const char *tps68470_led_names[] = {
> + [TPS68470_ILED_A] = "tps68470-iled_a",
> + [TPS68470_ILED_B] = "tps68470-iled_b",
> +};
> +
> +struct tps68470_led {
> + unsigned int led_id;
> + struct led_classdev lcdev;
> +};
> +
> +struct tps68470_device {
> + struct device *dev;
> + struct regmap *regmap;
> + struct tps68470_led leds[TPS68470_NUM_LEDS];
> +};
> +
> +enum ctrlb_current {
> + CTRLB_2MA = 0,
> + CTRLB_4MA = 1,
> + CTRLB_8MA = 2,
> + CTRLB_16MA = 3,
> +};
> +
> +static int tps68470_brightness_set(struct led_classdev *led_cdev, enum led_brightness brightness)
> +{
> + struct tps68470_led *led = lcdev_to_led(led_cdev);
> + struct tps68470_device *tps68470 = led_to_tps68470(led, led->led_id);
> + struct regmap *regmap = tps68470->regmap;
> +
> + switch (led->led_id) {
> + case TPS68470_ILED_A:
> + return regmap_update_bits(regmap, TPS68470_REG_ILEDCTL, TPS68470_ILEDCTL_ENA,
> + brightness ? TPS68470_ILEDCTL_ENA : 0);
> + case TPS68470_ILED_B:
> + return regmap_update_bits(regmap, TPS68470_REG_ILEDCTL, TPS68470_ILEDCTL_ENB,
> + brightness ? TPS68470_ILEDCTL_ENB : 0);
> + }
> + return -EINVAL;
> +}
> +
> +static enum led_brightness tps68470_brightness_get(struct led_classdev *led_cdev)
> +{
> + struct tps68470_led *led = lcdev_to_led(led_cdev);
> + struct tps68470_device *tps68470 = led_to_tps68470(led, led->led_id);
> + struct regmap *regmap = tps68470->regmap;
> + int ret = 0;
> + int value = 0;
> +
> + ret = regmap_read(regmap, TPS68470_REG_ILEDCTL, &value);
> + if (ret)
> + return dev_err_probe(led_cdev->dev, -EINVAL, "failed on reading register\n");
> +
> + switch (led->led_id) {
> + case TPS68470_ILED_A:
> + value = value & TPS68470_ILEDCTL_ENA;
> + break;
> + case TPS68470_ILED_B:
> + value = value & TPS68470_ILEDCTL_ENB;
> + break;
> + }
> +
> + return value ? LED_ON : LED_OFF;
> +}
> +
> +
> +static int tps68470_ledb_current_init(struct platform_device *pdev,
> + struct tps68470_device *tps68470)
> +{
> + int ret = 0;
> + unsigned int curr;
> +
> + /* configure LEDB current if the properties can be got */
> + if (!device_property_read_u32(&pdev->dev, "ti,ledb-current", &curr)) {
> + if (curr > CTRLB_16MA) {
> + dev_err(&pdev->dev,
> + "Invalid LEDB current value: %d\n",
> + curr);
> + return -EINVAL;
> + }
> + ret = regmap_update_bits(tps68470->regmap, TPS68470_REG_ILEDCTL,
> + TPS68470_ILEDCTL_CTRLB, curr);
> + }
> + return ret;
> +}
> +
> +static int tps68470_leds_probe(struct platform_device *pdev)
> +{
> + int i = 0;
> + int ret = 0;
> + struct tps68470_device *tps68470;
> + struct tps68470_led *led;
> + struct led_classdev *lcdev;
> +
> + tps68470 = devm_kzalloc(&pdev->dev, sizeof(struct tps68470_device),
> + GFP_KERNEL);
> + if (!tps68470)
> + return -ENOMEM;
> +
> + tps68470->dev = &pdev->dev;
> + tps68470->regmap = dev_get_drvdata(pdev->dev.parent);
> +
> + for (i = 0; i < TPS68470_NUM_LEDS; i++) {
> + led = &tps68470->leds[i];
> + lcdev = &led->lcdev;
> +
> + led->led_id = i;
> +
> + lcdev->name = devm_kasprintf(tps68470->dev, GFP_KERNEL, "%s::%s",
> + tps68470_led_names[i], LED_FUNCTION_INDICATOR);
> + if (!lcdev->name)
> + return -ENOMEM;
> +
> + lcdev->max_brightness = 1;
> + lcdev->brightness = 0;
> + lcdev->brightness_set_blocking = tps68470_brightness_set;
> + lcdev->brightness_get = tps68470_brightness_get;
> + lcdev->dev = &pdev->dev;
> +
> + ret = devm_led_classdev_register(tps68470->dev, lcdev);
> + if (ret) {
> + dev_err_probe(tps68470->dev, ret,
> + "error registering led\n");
> + goto err_exit;
> + }
> +
> + if (i == TPS68470_ILED_B) {
> + ret = tps68470_ledb_current_init(pdev, tps68470);
> + if (ret)
> + goto err_exit;
> + }
> + }
> +
> +err_exit:
> + if (ret) {
> + for (i = 0; i < TPS68470_NUM_LEDS; i++) {
> + if (tps68470->leds[i].lcdev.name)
> + devm_led_classdev_unregister(&pdev->dev,
> + &tps68470->leds[i].lcdev);
> + }
> + }
> +
> + return ret;
> +}
> +static struct platform_driver tps68470_led_driver = {
> + .driver = {
> + .name = "tps68470-led",
> + },
> + .probe = tps68470_leds_probe,
> +};
> +
> +module_platform_driver(tps68470_led_driver);
> +
> +MODULE_ALIAS("platform:tps68470-led");
> +MODULE_DESCRIPTION("LED driver for TPS68470 PMIC");
> +MODULE_LICENSE("GPL v2");
next prev parent reply other threads:[~2023-03-23 7:36 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-21 15:37 [PATCH v3 0/3] leds: tps68470: LED driver for TPS68470 Kate Hsuan
2023-03-21 15:37 ` [PATCH v3 1/3] platform: x86: int3472: Add MFD cell for tps68470 LED Kate Hsuan
2023-03-22 16:46 ` Hans de Goede
2023-03-23 12:23 ` Lee Jones
2023-03-23 12:31 ` Hans de Goede
2023-03-23 14:57 ` Lee Jones
2023-03-21 15:37 ` [PATCH v3 2/3] include: mfd: tps68470: Add masks for LEDA and LEDB Kate Hsuan
2023-03-21 15:37 ` [PATCH v3 3/3] leds: tps68470: Add LED control for tps68470 Kate Hsuan
2023-03-22 16:46 ` Hans de Goede
2023-03-23 7:36 ` Dan Scally [this message]
2023-03-23 11:15 ` Pavel Machek
2023-03-23 11:24 ` Hans de Goede
2023-03-23 11:26 ` Pavel Machek
2023-03-23 11:29 ` Hans de Goede
2023-03-23 11:31 ` Hans de Goede
2023-03-23 11:36 ` Pavel Machek
2023-03-23 12:36 ` Hans de Goede
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=aac749fa-3f33-6fb3-cfea-e7a11fd1d384@ideasonboard.com \
--to=dan.scally@ideasonboard.com \
--cc=djrscally@gmail.com \
--cc=hdegoede@redhat.com \
--cc=hpa@redhat.com \
--cc=lee@kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=markgross@kernel.org \
--cc=pavel@ucw.cz \
--cc=platform-driver-x86@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox