Re: [PATCH v2 1/6] dt-bindings: leds: Document TI LM3533 LED controller

[Daniel Thompson <daniel@riscstar.com>]

On Fri, May 29, 2026 at 01:07:50PM +0300, Svyatoslav Ryhel wrote:
> пт, 29 трав. 2026 р. о 12:51 Daniel Thompson <daniel@riscstar.com> пише:
> >
> > On Thu, May 28, 2026 at 04:51:18PM +0300, Svyatoslav Ryhel wrote:
> > > Document the LM3533 - a complete power source for backlight, keypad and
> > > indicator LEDs in smartphone handsets. The high-voltage inductive boost
> > > converter provides the power for two series LED strings display backlight
> > > and keypad functions.
> > >
> > > Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
> > > ---
> > >  .../leds/backlight/ti,lm3533-backlight.yaml   |  68 +++++++
> > >  .../bindings/leds/ti,lm3533-leds.yaml         |  66 +++++++
> > >  .../devicetree/bindings/leds/ti,lm3533.yaml   | 170 ++++++++++++++++++
> > >  3 files changed, 304 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/leds/backlight/ti,lm3533-backlight.yaml
> > >  create mode 100644 Documentation/devicetree/bindings/leds/ti,lm3533-leds.yaml
> > >  create mode 100644 Documentation/devicetree/bindings/leds/ti,lm3533.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/leds/backlight/ti,lm3533-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/ti,lm3533-backlight.yaml
> > > new file mode 100644
> > > index 000000000000..866b0fb8ed04
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/leds/backlight/ti,lm3533-backlight.yaml
> > > @@ -0,0 +1,68 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/leds/backlight/ti,lm3533-backlight.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: TI LM3533 high voltage series LED strings
> > > +
> > > +description:
> > > +  This is part of the TI LM3533 MFD device. It represents two high voltage series
> > > +  LED strings for display backlight controlled by the TI LM3533.
> > > +
> > > +maintainers:
> > > +  - Svyatoslav Ryhel <clamor95@gmail.com>
> > > +
> > > +allOf:
> > > +  - $ref: /schemas/leds/backlight/common.yaml#
> > > +
> > > +properties:
> > > +  compatible:
> > > +    const: ti,lm3533-backlight
> > > +
> > > +  reg:
> > > +    description: Control bank selection (0 = bank A, 1 = bank B).
> > > +    maximum: 1
> > >    <snip>
> > > +  ti,pwm-config-mask:
> > > +    $ref: /schemas/types.yaml#/definitions/uint32
> > > +    description: |
> > > +      Control Bank PWM Configuration Register mask that allows to configure
> > > +      PWM input in Zones 0-4
> > > +      BIT(0) - PWM Input is enabled
> > > +      BIT(1) - PWM Input is enabled in Zone 0
> > > +      BIT(2) - PWM Input is enabled in Zone 1
> > > +      BIT(3) - PWM Input is enabled in Zone 2
> > > +      BIT(4) - PWM Input is enabled in Zone 3
> > > +      BIT(5) - PWM Input is enabled in Zone 4
> >
> > This is optional and the drive implements a default (zero) that is not
> > documented here.
> >
> > Is zero a sane default from a DT binding point of view?
> >
>
> Yes, if property is missing then PWM input is disabled which is
> equivalent to setting all bits to 0.

So the default should be documented in the bindings?


Daniel.