* [linux-lvm] Re: Safely removing a phantom disc-wide PV
@ 2003-07-11 18:28 Chip McArtor
2003-07-11 19:02 ` [linux-lvm] Problems with LVM Petro
0 siblings, 1 reply; 9+ messages in thread
From: Chip McArtor @ 2003-07-11 18:28 UTC (permalink / raw)
To: linux-lvm
Well, I feel sort of dumb for answering my own problem, but since none of the lvm tools seemed to be of any use, as my VG was non-existant, I might as well tell you how I fixed my problem.
Basically, I reassigned the VG of the two corrupt PVs to some dummy VG. In this case, the real VG was "array" and the dummy VG was "arrey".
#dd if=/dev/hdf of=hdf.head bs=1024 count=1
#sed s/array/arrey/ hdf.head > hdf.test
#dd if=hdf.test of=/dev/hdf bs=1024 count=1
Those commands are pretty self-explanatory. Upon running vgscan after this, the hdf PV was still there, but instead of being assigned to 'array', it was assigned to 'arrey'. This meant that 'array' had no corrupt volumes in it, and as such could be loaded without incident.
There's probably a cleaner way of fixing the problem of a bad device-level PV, but this method seems to work pretty well.
-Chip
>In my current setup, I have 4 PVs forming my VG. Initially, two of the PVs took up only single partitions on separate discs [/dev/hdk2 and /dev/hdi2], while the other two PVs spanned the entirety of another two discs [/dev/hdf and /dev/hdj].
>
>At some point, I installed windows on an entirely different drive, and it must have recognized hdf and hdj as being empty (since they didnt' contain a partition table) and overwrote a bit here and there, corrupting both of those PVs. Realizing the problem with a device-wide PV, I built the VG again from scratch, this time creating partitions hdf1 and hdj1 which spanned the entire space of those drives.
>
>VG creation was successfully done with the following command:
>vgcreate array /dev/hdk2 /dev/hdi2 /dev/hdf1 and /dev/hdj
>
>The VG creation was a success, and soon I had created an LV and a filesystem on top of that. After I rebooted, however, I got the following error message:
>
>
>bash-2.05b# vgscan
>vgscan -- reading all physical volumes (this may take a while...)
>vgscan -- ERROR "vg_read_with_pv_and_lv(): current PV" can't get data of volume group "array" from physical volume(s)
>vgscan -- "/etc/lvmtab" and "/etc/lvmtab.d" successfully created
>vgscan -- WARNING: This program does not do a VGDA backup of your volume group
>
>
>Running pvscan showed me that /dev/hdk2, /dev/hdi2, /dev/hdf1, and /dev/hdj1 were all indeed shown belonging to my VG "array". However, the old PVs /dev/hdf and /dev/hdj were also present, also pointing to group "array". Because /dev/hdf and /dev/hdj were corrupt, the VG is now unloadable. How could I safely remove/disable hdf and hdj, without harming the valid PVs hdf1 and hdj1? vgremove is inoperable, since my VG "array" in unloadable. One possibility I was considering was running dd from /dev/zero to certain blocks on hdf and hdj, but I'm afraid to try something like that, since it might very well wipe out the partition tables and destroy hdf1 and hdj1 if I write to the wrong blocks.
>
>Any ideas?
>
>
>-Chip
^ permalink raw reply [flat|nested] 9+ messages in thread* [linux-lvm] Problems with LVM 2003-07-11 18:28 [linux-lvm] Re: Safely removing a phantom disc-wide PV Chip McArtor @ 2003-07-11 19:02 ` Petro 2003-07-13 5:14 ` Heinz J . Mauelshagen 0 siblings, 1 reply; 9+ messages in thread From: Petro @ 2003-07-11 19:02 UTC (permalink / raw) To: linux-lvm Hello again. I'm having a problem with LVM, and I'm really, really hoping you won't tell me it's because of: # CONFIG_NOHIGHMEM is not set CONFIG_HIGHMEM4G=y # CONFIG_HIGHMEM64G is not set CONFIG_HIGHMEM=y CONFIG_HIGHIO=y (linux kernel 2.4.21, lvm 1.0.7 stuff installed) I've got 8 boxes with 4 gig of memory, and 6 200 gig drives in a raid 0 setup, and I need to use LVM+Snapshots. I can setup and create a 1.09T logical volume, but when I go to create a snaphot, I get: lvcreate -- INFO: using default snapshot chunk size of 64 KB for "/dev/vg0/test" lvcreate -- ERROR "Cannot allocate memory" creating VGDA for "/dev/vg0/test" in kernel Now, in reading past posts there is some talk of how having "high memory" turned on will cause problems with snapshots. The problem is that on these machines I *need* 4 gig of memory, and I *need* snapshots. Help? --- Physical volume --- PV Name /dev/sda VG Name vg0 PV Size 1.09 TB [2344319232 secs] / NOT usable 32.31 MB [LVM: 267 KB] PV# 1 PV Status available Allocatable yes Cur LV 1 PE Size (KByte) 32768 Total PE 35770 Free PE 570 Allocated PE 35200 PV UUID LyEPH1-pq2I-D022-v5c9-98rp-n7Ff-4LnNKL --- Volume group --- VG Name vg0 VG Access read/write VG Status available/resizable VG # 0 MAX LV 256 Cur LV 1 Open LV 1 MAX LV Size 2 TB Max PV 256 Cur PV 1 Act PV 1 VG Size 1.09 TB PE Size 32 MB Total PE 35770 Alloc PE / Size 36032 / 1.10 TB Free PE / Size 4294967034 / 131071.99 TB VG UUID KciSkB-xbr8-22RM-zmke-6A69-6BEM-xLWMzv --- Logical volume --- LV Name /dev/vg0/lv0 VG Name vg0 LV Write Access read/write LV Status available LV # 1 # open 1 LV Size 1.07 TB Current LE 35200 Allocated LE 35200 Allocation next free Read ahead sectors 1024 Block device 58:0 procs memory swap io system cpu r b w swpd free buff cache si so bi bo in cs us sy id 0 0 0 0 3949704 1648 26104 0 0 3 2 27 5 0 0 100 -- "On two occasions, I have been asked [by members of Parliament], 'Pray, Mr. Babbage, if you put into the machine wrong figures, will the right answers come out?' I am not able to rightly apprehend the kind of confusion of ideas that could provoke such a question." -- Charles Babbage ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [linux-lvm] Problems with LVM 2003-07-11 19:02 ` [linux-lvm] Problems with LVM Petro @ 2003-07-13 5:14 ` Heinz J . Mauelshagen 2003-07-13 13:29 ` Petro 0 siblings, 1 reply; 9+ messages in thread From: Heinz J . Mauelshagen @ 2003-07-13 5:14 UTC (permalink / raw) To: linux-lvm Petro, what's the lvcreate command line ? (highmem may cause problems if you use the snapsho9t, creation should work fine) Regards, Heinz -- The LVM Guy -- On Fri, Jul 11, 2003 at 05:01:27PM -0700, Petro wrote: > Hello again. > > I'm having a problem with LVM, and I'm really, really hoping you won't > tell me it's because of: > > # CONFIG_NOHIGHMEM is not set > CONFIG_HIGHMEM4G=y > # CONFIG_HIGHMEM64G is not set > CONFIG_HIGHMEM=y > CONFIG_HIGHIO=y > > (linux kernel 2.4.21, lvm 1.0.7 stuff installed) > > I've got 8 boxes with 4 gig of memory, and 6 200 gig drives in a raid 0 > setup, and I need to use LVM+Snapshots. > > I can setup and create a 1.09T logical volume, but when I go to create a > snaphot, I get: > > lvcreate -- INFO: using default snapshot chunk size of 64 KB for "/dev/vg0/test" > lvcreate -- ERROR "Cannot allocate memory" creating VGDA for "/dev/vg0/test" in kernel > > Now, in reading past posts there is some talk of how having "high > memory" turned on will cause problems with snapshots. > > The problem is that on these machines I *need* 4 gig of memory, and I > *need* snapshots. > > Help? > > > --- Physical volume --- > PV Name /dev/sda > VG Name vg0 > PV Size 1.09 TB [2344319232 secs] / NOT usable 32.31 MB [LVM: 267 KB] > PV# 1 > PV Status available > Allocatable yes > Cur LV 1 > PE Size (KByte) 32768 > Total PE 35770 > Free PE 570 > Allocated PE 35200 > PV UUID LyEPH1-pq2I-D022-v5c9-98rp-n7Ff-4LnNKL > > --- Volume group --- > VG Name vg0 > VG Access read/write > VG Status available/resizable > VG # 0 > MAX LV 256 > Cur LV 1 > Open LV 1 > MAX LV Size 2 TB > Max PV 256 > Cur PV 1 > Act PV 1 > VG Size 1.09 TB > PE Size 32 MB > Total PE 35770 > Alloc PE / Size 36032 / 1.10 TB > Free PE / Size 4294967034 / 131071.99 TB > VG UUID KciSkB-xbr8-22RM-zmke-6A69-6BEM-xLWMzv > > --- Logical volume --- > LV Name /dev/vg0/lv0 > VG Name vg0 > LV Write Access read/write > LV Status available > LV # 1 > # open 1 > LV Size 1.07 TB > Current LE 35200 > Allocated LE 35200 > Allocation next free > Read ahead sectors 1024 > Block device 58:0 > > > procs memory swap io system cpu > r b w swpd free buff cache si so bi bo in cs us sy id > 0 0 0 0 3949704 1648 26104 0 0 3 2 27 5 0 0 100 > > > -- > "On two occasions, I have been asked [by members of Parliament], 'Pray, > Mr. Babbage, if you put into the machine wrong figures, will the right > answers come out?' I am not able to rightly apprehend the kind of confusion > of ideas that could provoke such a question." -- Charles Babbage > > _______________________________________________ > linux-lvm mailing list > linux-lvm@sistina.com > http://lists.sistina.com/mailman/listinfo/linux-lvm > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ *** Software bugs are stupid. Nevertheless it needs not so stupid people to solve them *** =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- Heinz Mauelshagen Sistina Software Inc. Senior Consultant/Developer Am Sonnenhang 11 56242 Marienrachdorf Germany Mauelshagen@Sistina.com +49 2626 141200 FAX 924446 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [linux-lvm] Problems with LVM 2003-07-13 5:14 ` Heinz J . Mauelshagen @ 2003-07-13 13:29 ` Petro 2003-07-13 15:26 ` Heinz J . Mauelshagen 0 siblings, 1 reply; 9+ messages in thread From: Petro @ 2003-07-13 13:29 UTC (permalink / raw) To: linux-lvm On Sun, Jul 13, 2003 at 12:11:51PM +0200, Heinz J . Mauelshagen wrote: > Petro, > what's the lvcreate command line ? lvcreate -L10G -n snap000 -s /dev/vg0 > (highmem may cause problems if you use the snapsho9t, creation should > work fine) Is this highmem problem across all 2.4 kernels, or just 2.4.19+? The first report I've seen of it is with a 2.4.19 kernel. > > Regards, > Heinz -- The LVM Guy -- > > On Fri, Jul 11, 2003 at 05:01:27PM -0700, Petro wrote: > > Hello again. > > > > I'm having a problem with LVM, and I'm really, really hoping you won't > > tell me it's because of: > > > > # CONFIG_NOHIGHMEM is not set > > CONFIG_HIGHMEM4G=y > > # CONFIG_HIGHMEM64G is not set > > CONFIG_HIGHMEM=y > > CONFIG_HIGHIO=y > > > > (linux kernel 2.4.21, lvm 1.0.7 stuff installed) > > > > I've got 8 boxes with 4 gig of memory, and 6 200 gig drives in a raid 0 > > setup, and I need to use LVM+Snapshots. > > > > I can setup and create a 1.09T logical volume, but when I go to create a > > snaphot, I get: > > > > lvcreate -- INFO: using default snapshot chunk size of 64 KB for "/dev/vg0/test" > > lvcreate -- ERROR "Cannot allocate memory" creating VGDA for "/dev/vg0/test" in kernel > > > > Now, in reading past posts there is some talk of how having "high > > memory" turned on will cause problems with snapshots. > > > > The problem is that on these machines I *need* 4 gig of memory, and I > > *need* snapshots. > > > > Help? > > > > > > --- Physical volume --- > > PV Name /dev/sda > > VG Name vg0 > > PV Size 1.09 TB [2344319232 secs] / NOT usable 32.31 MB [LVM: 267 KB] > > PV# 1 > > PV Status available > > Allocatable yes > > Cur LV 1 > > PE Size (KByte) 32768 > > Total PE 35770 > > Free PE 570 > > Allocated PE 35200 > > PV UUID LyEPH1-pq2I-D022-v5c9-98rp-n7Ff-4LnNKL > > > > --- Volume group --- > > VG Name vg0 > > VG Access read/write > > VG Status available/resizable > > VG # 0 > > MAX LV 256 > > Cur LV 1 > > Open LV 1 > > MAX LV Size 2 TB > > Max PV 256 > > Cur PV 1 > > Act PV 1 > > VG Size 1.09 TB > > PE Size 32 MB > > Total PE 35770 > > Alloc PE / Size 36032 / 1.10 TB > > Free PE / Size 4294967034 / 131071.99 TB > > VG UUID KciSkB-xbr8-22RM-zmke-6A69-6BEM-xLWMzv > > > > --- Logical volume --- > > LV Name /dev/vg0/lv0 > > VG Name vg0 > > LV Write Access read/write > > LV Status available > > LV # 1 > > # open 1 > > LV Size 1.07 TB > > Current LE 35200 > > Allocated LE 35200 > > Allocation next free > > Read ahead sectors 1024 > > Block device 58:0 > > > > > > procs memory swap io system cpu > > r b w swpd free buff cache si so bi bo in cs us sy id > > 0 0 0 0 3949704 1648 26104 0 0 3 2 27 5 0 0 100 > > > > > > -- > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > Mr. Babbage, if you put into the machine wrong figures, will the right > > answers come out?' I am not able to rightly apprehend the kind of confusion > > of ideas that could provoke such a question." -- Charles Babbage > > > > _______________________________________________ > > linux-lvm mailing list > > linux-lvm@sistina.com > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > *** Software bugs are stupid. > Nevertheless it needs not so stupid people to solve them *** > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > Heinz Mauelshagen Sistina Software Inc. > Senior Consultant/Developer Am Sonnenhang 11 > 56242 Marienrachdorf > Germany > Mauelshagen@Sistina.com +49 2626 141200 > FAX 924446 > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > _______________________________________________ > linux-lvm mailing list > linux-lvm@sistina.com > http://lists.sistina.com/mailman/listinfo/linux-lvm > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ -- "On two occasions, I have been asked [by members of Parliament], 'Pray, Mr. Babbage, if you put into the machine wrong figures, will the right answers come out?' I am not able to rightly apprehend the kind of confusion of ideas that could provoke such a question." -- Charles Babbage ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [linux-lvm] Problems with LVM 2003-07-13 13:29 ` Petro @ 2003-07-13 15:26 ` Heinz J . Mauelshagen 2003-07-13 19:35 ` Petro 0 siblings, 1 reply; 9+ messages in thread From: Heinz J . Mauelshagen @ 2003-07-13 15:26 UTC (permalink / raw) To: linux-lvm On Sun, Jul 13, 2003 at 11:27:43AM -0700, Petro wrote: > On Sun, Jul 13, 2003 at 12:11:51PM +0200, Heinz J . Mauelshagen wrote: > > Petro, > > what's the lvcreate command line ? > > lvcreate -L10G -n snap000 -s /dev/vg0 Looks like another vmalloc bug :( Kernel memory for snapshot exception tables gets allocated with vmalloc() which shouldn't fail (presumably there's enough memory free, which I assume in your case). > > > (highmem may cause problems if you use the snapsho9t, creation should > > work fine) > > Is this highmem problem across all 2.4 kernels, or just 2.4.19+? The > first report I've seen of it is with a 2.4.19 kernel. Didn't retest with kernel 2.4.21 yet. The ones before had it AFAIK. Regards, Heinz -- The LVM Guy -- > > > > > Regards, > > Heinz -- The LVM Guy -- > > > > On Fri, Jul 11, 2003 at 05:01:27PM -0700, Petro wrote: > > > Hello again. > > > > > > I'm having a problem with LVM, and I'm really, really hoping you won't > > > tell me it's because of: > > > > > > # CONFIG_NOHIGHMEM is not set > > > CONFIG_HIGHMEM4G=y > > > # CONFIG_HIGHMEM64G is not set > > > CONFIG_HIGHMEM=y > > > CONFIG_HIGHIO=y > > > > > > (linux kernel 2.4.21, lvm 1.0.7 stuff installed) > > > > > > I've got 8 boxes with 4 gig of memory, and 6 200 gig drives in a raid 0 > > > setup, and I need to use LVM+Snapshots. > > > > > > I can setup and create a 1.09T logical volume, but when I go to create a > > > snaphot, I get: > > > > > > lvcreate -- INFO: using default snapshot chunk size of 64 KB for "/dev/vg0/test" > > > lvcreate -- ERROR "Cannot allocate memory" creating VGDA for "/dev/vg0/test" in kernel > > > > > > Now, in reading past posts there is some talk of how having "high > > > memory" turned on will cause problems with snapshots. > > > > > > The problem is that on these machines I *need* 4 gig of memory, and I > > > *need* snapshots. > > > > > > Help? > > > > > > > > > --- Physical volume --- > > > PV Name /dev/sda > > > VG Name vg0 > > > PV Size 1.09 TB [2344319232 secs] / NOT usable 32.31 MB [LVM: 267 KB] > > > PV# 1 > > > PV Status available > > > Allocatable yes > > > Cur LV 1 > > > PE Size (KByte) 32768 > > > Total PE 35770 > > > Free PE 570 > > > Allocated PE 35200 > > > PV UUID LyEPH1-pq2I-D022-v5c9-98rp-n7Ff-4LnNKL > > > > > > --- Volume group --- > > > VG Name vg0 > > > VG Access read/write > > > VG Status available/resizable > > > VG # 0 > > > MAX LV 256 > > > Cur LV 1 > > > Open LV 1 > > > MAX LV Size 2 TB > > > Max PV 256 > > > Cur PV 1 > > > Act PV 1 > > > VG Size 1.09 TB > > > PE Size 32 MB > > > Total PE 35770 > > > Alloc PE / Size 36032 / 1.10 TB > > > Free PE / Size 4294967034 / 131071.99 TB > > > VG UUID KciSkB-xbr8-22RM-zmke-6A69-6BEM-xLWMzv > > > > > > --- Logical volume --- > > > LV Name /dev/vg0/lv0 > > > VG Name vg0 > > > LV Write Access read/write > > > LV Status available > > > LV # 1 > > > # open 1 > > > LV Size 1.07 TB > > > Current LE 35200 > > > Allocated LE 35200 > > > Allocation next free > > > Read ahead sectors 1024 > > > Block device 58:0 > > > > > > > > > procs memory swap io system cpu > > > r b w swpd free buff cache si so bi bo in cs us sy id > > > 0 0 0 0 3949704 1648 26104 0 0 3 2 27 5 0 0 100 > > > > > > > > > -- > > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > > Mr. Babbage, if you put into the machine wrong figures, will the right > > > answers come out?' I am not able to rightly apprehend the kind of confusion > > > of ideas that could provoke such a question." -- Charles Babbage > > > > > > _______________________________________________ > > > linux-lvm mailing list > > > linux-lvm@sistina.com > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > *** Software bugs are stupid. > > Nevertheless it needs not so stupid people to solve them *** > > > > _______________________________________________ > > linux-lvm mailing list > > linux-lvm@sistina.com > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > -- > "On two occasions, I have been asked [by members of Parliament], 'Pray, > Mr. Babbage, if you put into the machine wrong figures, will the right > answers come out?' I am not able to rightly apprehend the kind of confusion > of ideas that could provoke such a question." -- Charles Babbage > > _______________________________________________ > linux-lvm mailing list > linux-lvm@sistina.com > http://lists.sistina.com/mailman/listinfo/linux-lvm > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ *** Software bugs are stupid. Nevertheless it needs not so stupid people to solve them *** =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- Heinz Mauelshagen Sistina Software Inc. Senior Consultant/Developer Am Sonnenhang 11 56242 Marienrachdorf Germany Mauelshagen@Sistina.com +49 2626 141200 FAX 924446 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [linux-lvm] Problems with LVM 2003-07-13 15:26 ` Heinz J . Mauelshagen @ 2003-07-13 19:35 ` Petro 2003-07-13 22:43 ` Petro 2003-07-15 13:58 ` Heinz J . Mauelshagen 0 siblings, 2 replies; 9+ messages in thread From: Petro @ 2003-07-13 19:35 UTC (permalink / raw) To: linux-lvm On Sun, Jul 13, 2003 at 10:24:15PM +0200, Heinz J . Mauelshagen wrote: > On Sun, Jul 13, 2003 at 11:27:43AM -0700, Petro wrote: > > On Sun, Jul 13, 2003 at 12:11:51PM +0200, Heinz J . Mauelshagen wrote: > > > Petro, > > > what's the lvcreate command line ? > > > > lvcreate -L10G -n snap000 -s /dev/vg0 > Looks like another vmalloc bug :( You mean like this one: Jul 13 13:11:55 back03-gig kernel: kernel BUG at vmalloc.c:236! Jul 13 13:11:55 back03-gig kernel: invalid operand: 0000 Jul 13 13:11:55 back03-gig kernel: CPU: 2 Jul 13 13:11:55 back03-gig kernel: EIP: 0010:[__vmalloc+53/512] Not tainted > Kernel memory for snapshot exception tables gets allocated with vmalloc() > which shouldn't fail (presumably there's enough memory free, > which I assume in your case). Freshly rebooted machine with 4 gig of physical memory, and nothing else running. > > > (highmem may cause problems if you use the snapsho9t, creation should > > > work fine) > > Is this highmem problem across all 2.4 kernels, or just 2.4.19+? The > > first report I've seen of it is with a 2.4.19 kernel. > Didn't retest with kernel 2.4.21 yet. > The ones before had it AFAIK. Starting when? the dawn of time? Also, would switching to LVM2 sidestep this issue? > Regards, > Heinz -- The LVM Guy -- > > > > > > > > > Regards, > > > Heinz -- The LVM Guy -- > > > > > > On Fri, Jul 11, 2003 at 05:01:27PM -0700, Petro wrote: > > > > Hello again. > > > > > > > > I'm having a problem with LVM, and I'm really, really hoping you won't > > > > tell me it's because of: > > > > > > > > # CONFIG_NOHIGHMEM is not set > > > > CONFIG_HIGHMEM4G=y > > > > # CONFIG_HIGHMEM64G is not set > > > > CONFIG_HIGHMEM=y > > > > CONFIG_HIGHIO=y > > > > > > > > (linux kernel 2.4.21, lvm 1.0.7 stuff installed) > > > > > > > > I've got 8 boxes with 4 gig of memory, and 6 200 gig drives in a raid 0 > > > > setup, and I need to use LVM+Snapshots. > > > > > > > > I can setup and create a 1.09T logical volume, but when I go to create a > > > > snaphot, I get: > > > > > > > > lvcreate -- INFO: using default snapshot chunk size of 64 KB for "/dev/vg0/test" > > > > lvcreate -- ERROR "Cannot allocate memory" creating VGDA for "/dev/vg0/test" in kernel > > > > > > > > Now, in reading past posts there is some talk of how having "high > > > > memory" turned on will cause problems with snapshots. > > > > > > > > The problem is that on these machines I *need* 4 gig of memory, and I > > > > *need* snapshots. > > > > > > > > Help? > > > > > > > > > > > > --- Physical volume --- > > > > PV Name /dev/sda > > > > VG Name vg0 > > > > PV Size 1.09 TB [2344319232 secs] / NOT usable 32.31 MB [LVM: 267 KB] > > > > PV# 1 > > > > PV Status available > > > > Allocatable yes > > > > Cur LV 1 > > > > PE Size (KByte) 32768 > > > > Total PE 35770 > > > > Free PE 570 > > > > Allocated PE 35200 > > > > PV UUID LyEPH1-pq2I-D022-v5c9-98rp-n7Ff-4LnNKL > > > > > > > > --- Volume group --- > > > > VG Name vg0 > > > > VG Access read/write > > > > VG Status available/resizable > > > > VG # 0 > > > > MAX LV 256 > > > > Cur LV 1 > > > > Open LV 1 > > > > MAX LV Size 2 TB > > > > Max PV 256 > > > > Cur PV 1 > > > > Act PV 1 > > > > VG Size 1.09 TB > > > > PE Size 32 MB > > > > Total PE 35770 > > > > Alloc PE / Size 36032 / 1.10 TB > > > > Free PE / Size 4294967034 / 131071.99 TB > > > > VG UUID KciSkB-xbr8-22RM-zmke-6A69-6BEM-xLWMzv > > > > > > > > --- Logical volume --- > > > > LV Name /dev/vg0/lv0 > > > > VG Name vg0 > > > > LV Write Access read/write > > > > LV Status available > > > > LV # 1 > > > > # open 1 > > > > LV Size 1.07 TB > > > > Current LE 35200 > > > > Allocated LE 35200 > > > > Allocation next free > > > > Read ahead sectors 1024 > > > > Block device 58:0 > > > > > > > > > > > > procs memory swap io system cpu > > > > r b w swpd free buff cache si so bi bo in cs us sy id > > > > 0 0 0 0 3949704 1648 26104 0 0 3 2 27 5 0 0 100 > > > > > > > > > > > > -- > > > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > > > Mr. Babbage, if you put into the machine wrong figures, will the right > > > > answers come out?' I am not able to rightly apprehend the kind of confusion > > > > of ideas that could provoke such a question." -- Charles Babbage > > > > > > > > _______________________________________________ > > > > linux-lvm mailing list > > > > linux-lvm@sistina.com > > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > > > *** Software bugs are stupid. > > > Nevertheless it needs not so stupid people to solve them *** > > > > > > _______________________________________________ > > > linux-lvm mailing list > > > linux-lvm@sistina.com > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > -- > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > Mr. Babbage, if you put into the machine wrong figures, will the right > > answers come out?' I am not able to rightly apprehend the kind of confusion > > of ideas that could provoke such a question." -- Charles Babbage > > > > _______________________________________________ > > linux-lvm mailing list > > linux-lvm@sistina.com > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > *** Software bugs are stupid. > Nevertheless it needs not so stupid people to solve them *** > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > Heinz Mauelshagen Sistina Software Inc. > Senior Consultant/Developer Am Sonnenhang 11 > 56242 Marienrachdorf > Germany > Mauelshagen@Sistina.com +49 2626 141200 > FAX 924446 > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > _______________________________________________ > linux-lvm mailing list > linux-lvm@sistina.com > http://lists.sistina.com/mailman/listinfo/linux-lvm > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ -- "On two occasions, I have been asked [by members of Parliament], 'Pray, Mr. Babbage, if you put into the machine wrong figures, will the right answers come out?' I am not able to rightly apprehend the kind of confusion of ideas that could provoke such a question." -- Charles Babbage ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [linux-lvm] Problems with LVM 2003-07-13 19:35 ` Petro @ 2003-07-13 22:43 ` Petro 2003-07-15 13:58 ` Heinz J . Mauelshagen 1 sibling, 0 replies; 9+ messages in thread From: Petro @ 2003-07-13 22:43 UTC (permalink / raw) To: linux-lvm On Sun, Jul 13, 2003 at 05:34:08PM -0700, Petro wrote: > On Sun, Jul 13, 2003 at 10:24:15PM +0200, Heinz J . Mauelshagen wrote: > > On Sun, Jul 13, 2003 at 11:27:43AM -0700, Petro wrote: > > > On Sun, Jul 13, 2003 at 12:11:51PM +0200, Heinz J . Mauelshagen wrote: > > > > Petro, > > > > what's the lvcreate command line ? > > > > > > lvcreate -L10G -n snap000 -s /dev/vg0 > > Looks like another vmalloc bug :( > You mean like this one: > Jul 13 13:11:55 back03-gig kernel: kernel BUG at vmalloc.c:236! > Jul 13 13:11:55 back03-gig kernel: invalid operand: 0000 > Jul 13 13:11:55 back03-gig kernel: CPU: 2 > Jul 13 13:11:55 back03-gig kernel: EIP: 0010:[__vmalloc+53/512] > Not tainted Note that this is on the 2.4.18 kernel, not the 2.4.21 kernel. > > Kernel memory for snapshot exception tables gets allocated with vmalloc() > > which shouldn't fail (presumably there's enough memory free, > > which I assume in your case). > > Freshly rebooted machine with 4 gig of physical memory, and nothing else > running. > > > > > (highmem may cause problems if you use the snapsho9t, creation should > > > > work fine) > > > Is this highmem problem across all 2.4 kernels, or just 2.4.19+? The > > > first report I've seen of it is with a 2.4.19 kernel. > > Didn't retest with kernel 2.4.21 yet. > > The ones before had it AFAIK. > > Starting when? the dawn of time? > > Also, would switching to LVM2 sidestep this issue? > > > Regards, > > Heinz -- The LVM Guy -- > > > > > > > > > > > > > Regards, > > > > Heinz -- The LVM Guy -- > > > > > > > > On Fri, Jul 11, 2003 at 05:01:27PM -0700, Petro wrote: > > > > > Hello again. > > > > > > > > > > I'm having a problem with LVM, and I'm really, really hoping you won't > > > > > tell me it's because of: > > > > > > > > > > # CONFIG_NOHIGHMEM is not set > > > > > CONFIG_HIGHMEM4G=y > > > > > # CONFIG_HIGHMEM64G is not set > > > > > CONFIG_HIGHMEM=y > > > > > CONFIG_HIGHIO=y > > > > > > > > > > (linux kernel 2.4.21, lvm 1.0.7 stuff installed) > > > > > > > > > > I've got 8 boxes with 4 gig of memory, and 6 200 gig drives in a raid 0 > > > > > setup, and I need to use LVM+Snapshots. > > > > > > > > > > I can setup and create a 1.09T logical volume, but when I go to create a > > > > > snaphot, I get: > > > > > > > > > > lvcreate -- INFO: using default snapshot chunk size of 64 KB for "/dev/vg0/test" > > > > > lvcreate -- ERROR "Cannot allocate memory" creating VGDA for "/dev/vg0/test" in kernel > > > > > > > > > > Now, in reading past posts there is some talk of how having "high > > > > > memory" turned on will cause problems with snapshots. > > > > > > > > > > The problem is that on these machines I *need* 4 gig of memory, and I > > > > > *need* snapshots. > > > > > > > > > > Help? > > > > > > > > > > > > > > > --- Physical volume --- > > > > > PV Name /dev/sda > > > > > VG Name vg0 > > > > > PV Size 1.09 TB [2344319232 secs] / NOT usable 32.31 MB [LVM: 267 KB] > > > > > PV# 1 > > > > > PV Status available > > > > > Allocatable yes > > > > > Cur LV 1 > > > > > PE Size (KByte) 32768 > > > > > Total PE 35770 > > > > > Free PE 570 > > > > > Allocated PE 35200 > > > > > PV UUID LyEPH1-pq2I-D022-v5c9-98rp-n7Ff-4LnNKL > > > > > > > > > > --- Volume group --- > > > > > VG Name vg0 > > > > > VG Access read/write > > > > > VG Status available/resizable > > > > > VG # 0 > > > > > MAX LV 256 > > > > > Cur LV 1 > > > > > Open LV 1 > > > > > MAX LV Size 2 TB > > > > > Max PV 256 > > > > > Cur PV 1 > > > > > Act PV 1 > > > > > VG Size 1.09 TB > > > > > PE Size 32 MB > > > > > Total PE 35770 > > > > > Alloc PE / Size 36032 / 1.10 TB > > > > > Free PE / Size 4294967034 / 131071.99 TB > > > > > VG UUID KciSkB-xbr8-22RM-zmke-6A69-6BEM-xLWMzv > > > > > > > > > > --- Logical volume --- > > > > > LV Name /dev/vg0/lv0 > > > > > VG Name vg0 > > > > > LV Write Access read/write > > > > > LV Status available > > > > > LV # 1 > > > > > # open 1 > > > > > LV Size 1.07 TB > > > > > Current LE 35200 > > > > > Allocated LE 35200 > > > > > Allocation next free > > > > > Read ahead sectors 1024 > > > > > Block device 58:0 > > > > > > > > > > > > > > > procs memory swap io system cpu > > > > > r b w swpd free buff cache si so bi bo in cs us sy id > > > > > 0 0 0 0 3949704 1648 26104 0 0 3 2 27 5 0 0 100 > > > > > > > > > > > > > > > -- > > > > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > > > > Mr. Babbage, if you put into the machine wrong figures, will the right > > > > > answers come out?' I am not able to rightly apprehend the kind of confusion > > > > > of ideas that could provoke such a question." -- Charles Babbage > > > > > > > > > > _______________________________________________ > > > > > linux-lvm mailing list > > > > > linux-lvm@sistina.com > > > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > > > > > *** Software bugs are stupid. > > > > Nevertheless it needs not so stupid people to solve them *** > > > > > > > > _______________________________________________ > > > > linux-lvm mailing list > > > > linux-lvm@sistina.com > > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > > > -- > > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > > Mr. Babbage, if you put into the machine wrong figures, will the right > > > answers come out?' I am not able to rightly apprehend the kind of confusion > > > of ideas that could provoke such a question." -- Charles Babbage > > > > > > _______________________________________________ > > > linux-lvm mailing list > > > linux-lvm@sistina.com > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > *** Software bugs are stupid. > > Nevertheless it needs not so stupid people to solve them *** > > > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > > > Heinz Mauelshagen Sistina Software Inc. > > Senior Consultant/Developer Am Sonnenhang 11 > > 56242 Marienrachdorf > > Germany > > Mauelshagen@Sistina.com +49 2626 141200 > > FAX 924446 > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > > > _______________________________________________ > > linux-lvm mailing list > > linux-lvm@sistina.com > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > -- > "On two occasions, I have been asked [by members of Parliament], 'Pray, > Mr. Babbage, if you put into the machine wrong figures, will the right > answers come out?' I am not able to rightly apprehend the kind of confusion > of ideas that could provoke such a question." -- Charles Babbage > > _______________________________________________ > linux-lvm mailing list > linux-lvm@sistina.com > http://lists.sistina.com/mailman/listinfo/linux-lvm > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ -- "On two occasions, I have been asked [by members of Parliament], 'Pray, Mr. Babbage, if you put into the machine wrong figures, will the right answers come out?' I am not able to rightly apprehend the kind of confusion of ideas that could provoke such a question." -- Charles Babbage ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [linux-lvm] Problems with LVM 2003-07-13 19:35 ` Petro 2003-07-13 22:43 ` Petro @ 2003-07-15 13:58 ` Heinz J . Mauelshagen 2003-07-15 20:09 ` Petro 1 sibling, 1 reply; 9+ messages in thread From: Heinz J . Mauelshagen @ 2003-07-15 13:58 UTC (permalink / raw) To: linux-lvm On Sun, Jul 13, 2003 at 05:34:08PM -0700, Petro wrote: > On Sun, Jul 13, 2003 at 10:24:15PM +0200, Heinz J . Mauelshagen wrote: > > On Sun, Jul 13, 2003 at 11:27:43AM -0700, Petro wrote: > > > On Sun, Jul 13, 2003 at 12:11:51PM +0200, Heinz J . Mauelshagen wrote: > > > > Petro, > > > > what's the lvcreate command line ? > > > > > > lvcreate -L10G -n snap000 -s /dev/vg0 > > Looks like another vmalloc bug :( Yes. > Jul 13 13:11:55 back03-gig kernel: kernel BUG at vmalloc.c:236! > Jul 13 13:11:55 back03-gig kernel: invalid operand: 0000 > Jul 13 13:11:55 back03-gig kernel: CPU: 2 > Jul 13 13:11:55 back03-gig kernel: EIP: 0010:[__vmalloc+53/512] > Not tainted > > > Kernel memory for snapshot exception tables gets allocated with vmalloc() > > which shouldn't fail (presumably there's enough memory free, > > which I assume in your case). > > Freshly rebooted machine with 4 gig of physical memory, and nothing else > running. Which should happilly work in that case. > > > > > (highmem may cause problems if you use the snapsho9t, creation should > > > > work fine) > > > Is this highmem problem across all 2.4 kernels, or just 2.4.19+? The > > > first report I've seen of it is with a 2.4.19 kernel. > > Didn't retest with kernel 2.4.21 yet. > > The ones before had it AFAIK. > > Starting when? the dawn of time? :-) We realized it in 2.4.19 for the first time but you prove that it was in 2.4.18 as well. Anyone ? > > Also, would switching to LVM2 sidestep this issue? Not that we can tell because it's a general vm problem. Regards, Heinz -- The LVM Guy -- > > > > > > > > On Fri, Jul 11, 2003 at 05:01:27PM -0700, Petro wrote: > > > > > Hello again. > > > > > > > > > > I'm having a problem with LVM, and I'm really, really hoping you won't > > > > > tell me it's because of: > > > > > > > > > > # CONFIG_NOHIGHMEM is not set > > > > > CONFIG_HIGHMEM4G=y > > > > > # CONFIG_HIGHMEM64G is not set > > > > > CONFIG_HIGHMEM=y > > > > > CONFIG_HIGHIO=y > > > > > > > > > > (linux kernel 2.4.21, lvm 1.0.7 stuff installed) > > > > > > > > > > I've got 8 boxes with 4 gig of memory, and 6 200 gig drives in a raid 0 > > > > > setup, and I need to use LVM+Snapshots. > > > > > > > > > > I can setup and create a 1.09T logical volume, but when I go to create a > > > > > snaphot, I get: > > > > > > > > > > lvcreate -- INFO: using default snapshot chunk size of 64 KB for "/dev/vg0/test" > > > > > lvcreate -- ERROR "Cannot allocate memory" creating VGDA for "/dev/vg0/test" in kernel > > > > > > > > > > Now, in reading past posts there is some talk of how having "high > > > > > memory" turned on will cause problems with snapshots. > > > > > > > > > > The problem is that on these machines I *need* 4 gig of memory, and I > > > > > *need* snapshots. > > > > > > > > > > Help? > > > > > > > > > > > > > > > --- Physical volume --- > > > > > PV Name /dev/sda > > > > > VG Name vg0 > > > > > PV Size 1.09 TB [2344319232 secs] / NOT usable 32.31 MB [LVM: 267 KB] > > > > > PV# 1 > > > > > PV Status available > > > > > Allocatable yes > > > > > Cur LV 1 > > > > > PE Size (KByte) 32768 > > > > > Total PE 35770 > > > > > Free PE 570 > > > > > Allocated PE 35200 > > > > > PV UUID LyEPH1-pq2I-D022-v5c9-98rp-n7Ff-4LnNKL > > > > > > > > > > --- Volume group --- > > > > > VG Name vg0 > > > > > VG Access read/write > > > > > VG Status available/resizable > > > > > VG # 0 > > > > > MAX LV 256 > > > > > Cur LV 1 > > > > > Open LV 1 > > > > > MAX LV Size 2 TB > > > > > Max PV 256 > > > > > Cur PV 1 > > > > > Act PV 1 > > > > > VG Size 1.09 TB > > > > > PE Size 32 MB > > > > > Total PE 35770 > > > > > Alloc PE / Size 36032 / 1.10 TB > > > > > Free PE / Size 4294967034 / 131071.99 TB > > > > > VG UUID KciSkB-xbr8-22RM-zmke-6A69-6BEM-xLWMzv > > > > > > > > > > --- Logical volume --- > > > > > LV Name /dev/vg0/lv0 > > > > > VG Name vg0 > > > > > LV Write Access read/write > > > > > LV Status available > > > > > LV # 1 > > > > > # open 1 > > > > > LV Size 1.07 TB > > > > > Current LE 35200 > > > > > Allocated LE 35200 > > > > > Allocation next free > > > > > Read ahead sectors 1024 > > > > > Block device 58:0 > > > > > > > > > > > > > > > procs memory swap io system cpu > > > > > r b w swpd free buff cache si so bi bo in cs us sy id > > > > > 0 0 0 0 3949704 1648 26104 0 0 3 2 27 5 0 0 100 > > > > > > > > > > > > > > > -- > > > > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > > > > Mr. Babbage, if you put into the machine wrong figures, will the right > > > > > answers come out?' I am not able to rightly apprehend the kind of confusion > > > > > of ideas that could provoke such a question." -- Charles Babbage > > > > > > > > > > _______________________________________________ > > > > > linux-lvm mailing list > > > > > linux-lvm@sistina.com > > > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > > > > > *** Software bugs are stupid. > > > > Nevertheless it needs not so stupid people to solve them *** > > > > > > > > _______________________________________________ > > > > linux-lvm mailing list > > > > linux-lvm@sistina.com > > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > > > -- > > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > > Mr. Babbage, if you put into the machine wrong figures, will the right > > > answers come out?' I am not able to rightly apprehend the kind of confusion > > > of ideas that could provoke such a question." -- Charles Babbage > > > > > > _______________________________________________ > > > linux-lvm mailing list > > > linux-lvm@sistina.com > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > *** Software bugs are stupid. > > Nevertheless it needs not so stupid people to solve them *** > > > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > > > Heinz Mauelshagen Sistina Software Inc. > > Senior Consultant/Developer Am Sonnenhang 11 > > 56242 Marienrachdorf > > Germany > > Mauelshagen@Sistina.com +49 2626 141200 > > FAX 924446 > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > > > _______________________________________________ > > linux-lvm mailing list > > linux-lvm@sistina.com > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > -- > "On two occasions, I have been asked [by members of Parliament], 'Pray, > Mr. Babbage, if you put into the machine wrong figures, will the right > answers come out?' I am not able to rightly apprehend the kind of confusion > of ideas that could provoke such a question." -- Charles Babbage > > _______________________________________________ > linux-lvm mailing list > linux-lvm@sistina.com > http://lists.sistina.com/mailman/listinfo/linux-lvm > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ -- Regards, Heinz -- The LVM Guy -- *** Software bugs are stupid. Nevertheless it needs not so stupid people to solve them *** =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- Heinz Mauelshagen Sistina Software Inc. Senior Consultant/Developer Am Sonnenhang 11 56242 Marienrachdorf Germany Mauelshagen@Sistina.com +49 2626 141200 FAX 924446 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [linux-lvm] Problems with LVM 2003-07-15 13:58 ` Heinz J . Mauelshagen @ 2003-07-15 20:09 ` Petro 0 siblings, 0 replies; 9+ messages in thread From: Petro @ 2003-07-15 20:09 UTC (permalink / raw) To: linux-lvm On Tue, Jul 15, 2003 at 08:55:23PM +0200, Heinz J . Mauelshagen wrote: > On Sun, Jul 13, 2003 at 05:34:08PM -0700, Petro wrote: > > On Sun, Jul 13, 2003 at 10:24:15PM +0200, Heinz J . Mauelshagen wrote: > > > On Sun, Jul 13, 2003 at 11:27:43AM -0700, Petro wrote: > > > > On Sun, Jul 13, 2003 at 12:11:51PM +0200, Heinz J . Mauelshagen wrote: > > > > > Petro, > > > > > what's the lvcreate command line ? > > > > lvcreate -L10G -n snap000 -s /dev/vg0 > > > Looks like another vmalloc bug :( > Yes. > > Jul 13 13:11:55 back03-gig kernel: kernel BUG at vmalloc.c:236! > > Jul 13 13:11:55 back03-gig kernel: invalid operand: 0000 > > Jul 13 13:11:55 back03-gig kernel: CPU: 2 > > Jul 13 13:11:55 back03-gig kernel: EIP: 0010:[__vmalloc+53/512] > > Not tainted > > > Kernel memory for snapshot exception tables gets allocated with vmalloc() > > > which shouldn't fail (presumably there's enough memory free, > > > which I assume in your case). > > Freshly rebooted machine with 4 gig of physical memory, and nothing else > > running. > Which should happilly work in that case. It doesn't. > > > > > (highmem may cause problems if you use the snapsho9t, creation should > > > > > work fine) > > > > Is this highmem problem across all 2.4 kernels, or just 2.4.19+? The > > > > first report I've seen of it is with a 2.4.19 kernel. > > > Didn't retest with kernel 2.4.21 yet. > > > The ones before had it AFAIK. > > Starting when? the dawn of time? > :-) > We realized it in 2.4.19 for the first time but you prove that it was in 2.4.18 > as well. > Anyone ? The funny thing is that I've got some 2.4.18 boxes with *IDENTICAL* configurations except for the disk sizes that work just fine. These (the working boxes) have 6 80 gig disks attached to a 3ware card in a stripe, and have been running fine since Feburary. This is why I blew off the "doesn't work with highmem" stuff when it was posted earlier--it was working for me on PV of 447.17 GB, with a VG of 447.16 GB, and an LV of 435.00 GB. These (we've got 5 of them) are are main database servers (2 clusters, one spare). I've also had "lesser" machines running 2.4.18 doing the same thing. (4x80 drives instead of 6x80). > > Also, would switching to LVM2 sidestep this issue? > Not that we can tell because it's a general vm problem. This is what makes my boss curse Linux. <sigh> Time to start reading the help wanted adds. > Regards, > Heinz -- The LVM Guy -- > > > > > > > > > > > On Fri, Jul 11, 2003 at 05:01:27PM -0700, Petro wrote: > > > > > > Hello again. > > > > > > > > > > > > I'm having a problem with LVM, and I'm really, really hoping you won't > > > > > > tell me it's because of: > > > > > > > > > > > > # CONFIG_NOHIGHMEM is not set > > > > > > CONFIG_HIGHMEM4G=y > > > > > > # CONFIG_HIGHMEM64G is not set > > > > > > CONFIG_HIGHMEM=y > > > > > > CONFIG_HIGHIO=y > > > > > > > > > > > > (linux kernel 2.4.21, lvm 1.0.7 stuff installed) > > > > > > > > > > > > I've got 8 boxes with 4 gig of memory, and 6 200 gig drives in a raid 0 > > > > > > setup, and I need to use LVM+Snapshots. > > > > > > > > > > > > I can setup and create a 1.09T logical volume, but when I go to create a > > > > > > snaphot, I get: > > > > > > > > > > > > lvcreate -- INFO: using default snapshot chunk size of 64 KB for "/dev/vg0/test" > > > > > > lvcreate -- ERROR "Cannot allocate memory" creating VGDA for "/dev/vg0/test" in kernel > > > > > > > > > > > > Now, in reading past posts there is some talk of how having "high > > > > > > memory" turned on will cause problems with snapshots. > > > > > > > > > > > > The problem is that on these machines I *need* 4 gig of memory, and I > > > > > > *need* snapshots. > > > > > > > > > > > > Help? > > > > > > > > > > > > > > > > > > --- Physical volume --- > > > > > > PV Name /dev/sda > > > > > > VG Name vg0 > > > > > > PV Size 1.09 TB [2344319232 secs] / NOT usable 32.31 MB [LVM: 267 KB] > > > > > > PV# 1 > > > > > > PV Status available > > > > > > Allocatable yes > > > > > > Cur LV 1 > > > > > > PE Size (KByte) 32768 > > > > > > Total PE 35770 > > > > > > Free PE 570 > > > > > > Allocated PE 35200 > > > > > > PV UUID LyEPH1-pq2I-D022-v5c9-98rp-n7Ff-4LnNKL > > > > > > > > > > > > --- Volume group --- > > > > > > VG Name vg0 > > > > > > VG Access read/write > > > > > > VG Status available/resizable > > > > > > VG # 0 > > > > > > MAX LV 256 > > > > > > Cur LV 1 > > > > > > Open LV 1 > > > > > > MAX LV Size 2 TB > > > > > > Max PV 256 > > > > > > Cur PV 1 > > > > > > Act PV 1 > > > > > > VG Size 1.09 TB > > > > > > PE Size 32 MB > > > > > > Total PE 35770 > > > > > > Alloc PE / Size 36032 / 1.10 TB > > > > > > Free PE / Size 4294967034 / 131071.99 TB > > > > > > VG UUID KciSkB-xbr8-22RM-zmke-6A69-6BEM-xLWMzv > > > > > > > > > > > > --- Logical volume --- > > > > > > LV Name /dev/vg0/lv0 > > > > > > VG Name vg0 > > > > > > LV Write Access read/write > > > > > > LV Status available > > > > > > LV # 1 > > > > > > # open 1 > > > > > > LV Size 1.07 TB > > > > > > Current LE 35200 > > > > > > Allocated LE 35200 > > > > > > Allocation next free > > > > > > Read ahead sectors 1024 > > > > > > Block device 58:0 > > > > > > > > > > > > > > > > > > procs memory swap io system cpu > > > > > > r b w swpd free buff cache si so bi bo in cs us sy id > > > > > > 0 0 0 0 3949704 1648 26104 0 0 3 2 27 5 0 0 100 > > > > > > > > > > > > > > > > > > -- > > > > > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > > > > > Mr. Babbage, if you put into the machine wrong figures, will the right > > > > > > answers come out?' I am not able to rightly apprehend the kind of confusion > > > > > > of ideas that could provoke such a question." -- Charles Babbage > > > > > > > > > > > > _______________________________________________ > > > > > > linux-lvm mailing list > > > > > > linux-lvm@sistina.com > > > > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > > > > > > > *** Software bugs are stupid. > > > > > Nevertheless it needs not so stupid people to solve them *** > > > > > > > > > > _______________________________________________ > > > > > linux-lvm mailing list > > > > > linux-lvm@sistina.com > > > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > > > > > -- > > > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > > > Mr. Babbage, if you put into the machine wrong figures, will the right > > > > answers come out?' I am not able to rightly apprehend the kind of confusion > > > > of ideas that could provoke such a question." -- Charles Babbage > > > > > > > > _______________________________________________ > > > > linux-lvm mailing list > > > > linux-lvm@sistina.com > > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > > > *** Software bugs are stupid. > > > Nevertheless it needs not so stupid people to solve them *** > > > > > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > > > > > Heinz Mauelshagen Sistina Software Inc. > > > Senior Consultant/Developer Am Sonnenhang 11 > > > 56242 Marienrachdorf > > > Germany > > > Mauelshagen@Sistina.com +49 2626 141200 > > > FAX 924446 > > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > > > > > _______________________________________________ > > > linux-lvm mailing list > > > linux-lvm@sistina.com > > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > -- > > "On two occasions, I have been asked [by members of Parliament], 'Pray, > > Mr. Babbage, if you put into the machine wrong figures, will the right > > answers come out?' I am not able to rightly apprehend the kind of confusion > > of ideas that could provoke such a question." -- Charles Babbage > > > > _______________________________________________ > > linux-lvm mailing list > > linux-lvm@sistina.com > > http://lists.sistina.com/mailman/listinfo/linux-lvm > > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > -- > > Regards, > Heinz -- The LVM Guy -- > > *** Software bugs are stupid. > Nevertheless it needs not so stupid people to solve them *** > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > Heinz Mauelshagen Sistina Software Inc. > Senior Consultant/Developer Am Sonnenhang 11 > 56242 Marienrachdorf > Germany > Mauelshagen@Sistina.com +49 2626 141200 > FAX 924446 > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > > _______________________________________________ > linux-lvm mailing list > linux-lvm@sistina.com > http://lists.sistina.com/mailman/listinfo/linux-lvm > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ -- "On two occasions, I have been asked [by members of Parliament], 'Pray, Mr. Babbage, if you put into the machine wrong figures, will the right answers come out?' I am not able to rightly apprehend the kind of confusion of ideas that could provoke such a question." -- Charles Babbage ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2003-07-15 20:09 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2003-07-11 18:28 [linux-lvm] Re: Safely removing a phantom disc-wide PV Chip McArtor 2003-07-11 19:02 ` [linux-lvm] Problems with LVM Petro 2003-07-13 5:14 ` Heinz J . Mauelshagen 2003-07-13 13:29 ` Petro 2003-07-13 15:26 ` Heinz J . Mauelshagen 2003-07-13 19:35 ` Petro 2003-07-13 22:43 ` Petro 2003-07-15 13:58 ` Heinz J . Mauelshagen 2003-07-15 20:09 ` Petro
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).