* [linux-lvm] vgchange partial mount fails @ 2005-11-07 22:12 Tom Robinson 2005-11-08 10:00 ` Heinz Mauelshagen 0 siblings, 1 reply; 5+ messages in thread From: Tom Robinson @ 2005-11-07 22:12 UTC (permalink / raw) To: linux-lvm Hi, I'm trying to do a partial mount of a VG in order to rescue data from it (the last of the 8 PVs has died) If I do vgchange -P -a y vg1 It says: Partial mode. Incomplete volume groups will be activated read-only. 7 PV(s) found for VG vg1: expected 8 Logical volume (lv1) contains an incomplete mapping table. 7 PV(s) found for VG vg1: expected 8 Logical volume (lv1) contains an incomplete mapping table. 1 logical volume(s) in volume group "vg1" now active Which looks like it might have worked, but in /dev/mapper I have: crw-rw---- 1 root root 10, 63 May 30 02:48 control brw------- 1 root root 254, 0 Oct 25 13:20 vg1-lv1 But I can't mount vg1-lv1 (its ext2 - but it says "must specify fs type). What is wrong? Have I misconfigured lvm / dm? are there any lines I need in my config file? Are there any tools I can run to get more info? The array was built with LVM1 & 2.4.18, I'm now using LVM2/DM under 2.6.11.10 Also, It looks like it has done something, because if I try to deactivate it with "vgchange -P -a n vg1" I get: Partial mode. Incomplete volume groups will be activated read-only. 7 PV(s) found for VG vg1: expected 8 Logical volume (lv1) contains an incomplete mapping table. Can't deactivate volume group "vg1" with 1 open logical volume(s) Any help greatly appreciated. Kind regards, Tom ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [linux-lvm] vgchange partial mount fails 2005-11-07 22:12 [linux-lvm] vgchange partial mount fails Tom Robinson @ 2005-11-08 10:00 ` Heinz Mauelshagen 2005-11-08 11:06 ` Tom Robinson 0 siblings, 1 reply; 5+ messages in thread From: Heinz Mauelshagen @ 2005-11-08 10:00 UTC (permalink / raw) To: LVM general discussion and development On Mon, Nov 07, 2005 at 10:12:32PM +0000, Tom Robinson wrote: > > Hi, > > I'm trying to do a partial mount of a VG in order to rescue data from it > (the last of the 8 PVs has died) > > If I do vgchange -P -a y vg1 > It says: > > Partial mode. Incomplete volume groups will be activated read-only. > 7 PV(s) found for VG vg1: expected 8 > Logical volume (lv1) contains an incomplete mapping table. > 7 PV(s) found for VG vg1: expected 8 > Logical volume (lv1) contains an incomplete mapping table. > 1 logical volume(s) in volume group "vg1" now active > > Which looks like it might have worked, but in /dev/mapper I have: > > crw-rw---- 1 root root 10, 63 May 30 02:48 control > brw------- 1 root root 254, 0 Oct 25 13:20 vg1-lv1 > > But I can't mount vg1-lv1 (its ext2 - but it says "must specify fs type). Looks like expected behaviour. You're likely missing the beginning of your filesystem which was mapped to the dead PV and the fs code fails to find its metadata (ie. superblock). Check with "lvdisplay -m /dev/vg1/lv1" Regards, Heinz -- The LVM Guy -- > > What is wrong? Have I misconfigured lvm / dm? > are there any lines I need in my config file? > Are there any tools I can run to get more info? > > The array was built with LVM1 & 2.4.18, > I'm now using LVM2/DM under 2.6.11.10 > > Also, It looks like it has done something, because if I try > to deactivate it with "vgchange -P -a n vg1" I get: > > Partial mode. Incomplete volume groups will be activated read-only. > 7 PV(s) found for VG vg1: expected 8 > Logical volume (lv1) contains an incomplete mapping table. > Can't deactivate volume group "vg1" with 1 open logical volume(s) > > Any help greatly appreciated. > Kind regards, > Tom > > > _______________________________________________ > linux-lvm mailing list > linux-lvm@redhat.com > https://www.redhat.com/mailman/listinfo/linux-lvm > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- Heinz Mauelshagen Red Hat GmbH Consulting Development Engineer Am Sonnenhang 11 Cluster and Storage Development 56242 Marienrachdorf Germany Mauelshagen@RedHat.com +49 2626 141200 FAX 924446 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [linux-lvm] vgchange partial mount fails 2005-11-08 10:00 ` Heinz Mauelshagen @ 2005-11-08 11:06 ` Tom Robinson 2005-11-08 12:53 ` Heinz Mauelshagen 0 siblings, 1 reply; 5+ messages in thread From: Tom Robinson @ 2005-11-08 11:06 UTC (permalink / raw) To: LVM general discussion and development Heinz Mauelshagen wrote: >On Mon, Nov 07, 2005 at 10:12:32PM +0000, Tom Robinson wrote: > > >>Hi, >> >>I'm trying to do a partial mount of a VG in order to rescue data from it >>(the last of the 8 PVs has died) >> >>If I do vgchange -P -a y vg1 >>It says: >> >> Partial mode. Incomplete volume groups will be activated read-only. >> 7 PV(s) found for VG vg1: expected 8 >> Logical volume (lv1) contains an incomplete mapping table. >> 7 PV(s) found for VG vg1: expected 8 >> Logical volume (lv1) contains an incomplete mapping table. >> 1 logical volume(s) in volume group "vg1" now active >> >>Which looks like it might have worked, but in /dev/mapper I have: >> >>crw-rw---- 1 root root 10, 63 May 30 02:48 control >>brw------- 1 root root 254, 0 Oct 25 13:20 vg1-lv1 >> >>But I can't mount vg1-lv1 (its ext2 - but it says "must specify fs type). >> >> > >Looks like expected behaviour. > >You're likely missing the beginning of your filesystem which was mapped >to the dead PV and the fs code fails to find its metadata >(ie. superblock). > >Check with "lvdisplay -m /dev/vg1/lv1" > > Thanks for your response, Heinz, vaus root # lvdisplay -m /dev/vg1/lv1 7 PV(s) found for VG vg1: expected 8 7 PV(s) found for VG vg1: expected 8 Volume group "vg1" not found Thing is, /dev/vg1/lv1 doesn't exist at all, It used to, when everything was working. Only /dev/mapper exists. I have had the server running for about 3 years, and only added the last (dead) PV about 2 months ago so would it still put the superblock there? Any suggestions at all on how to rescue any data? Oh, heres the first bit of output of lvdisplay -mP /dev/vg1/lv1 if it helps: Partial mode. Incomplete volume groups will be activated read-only. --- Logical volume --- LV Name /dev/vg1/lv1 VG Name vg1 LV UUID 000000-0000-0000-0000-0000-0000-000000 LV Write Access read/write LV Status available # open 1 LV Size 1.51 TB Current LE 49447 Segments 7486 Allocation normal Read ahead sectors 1024 Block device 254:0 --- Segments --- Logical extent 0 to 4883: Type linear Physical volume /dev/cdrom Physical extents 0 to 4883 Logical extent 4884 to 8545: Type linear Physical volume /dev/hdf Physical extents 0 to 3661 Logical extent 8546 to 12051: Type linear Physical volume /dev/hde4 Physical extents 0 to 3505 Logical extent 12052 to 19530: Type linear Physical volume /dev/hdh Physical extents 0 to 7478 Logical extent 19531 to 27009: Type linear Physical volume /dev/hda Physical extents 0 to 7478 Logical extent 27010 to 34488: Type linear Physical volume /dev/hdb Physical extents 0 to 7478 Logical extent 34489 to 41967: Type linear Physical volume /dev/hdc Physical extents 0 to 7478 Logical extent 41968 to 41968: Type linear Physical volume Missing Logical extent 41969 to 41969: Type linear Physical volume Missing etc...... Regards, Tom >Regards, >Heinz -- The LVM Guy -- > > > vaus root # lvdisplay -m /dev/vg1/lv1 7 PV(s) found for VG vg1: expected 8 7 PV(s) found for VG vg1: expected 8 Volume group "vg1" not found >>What is wrong? Have I misconfigured lvm / dm? >>are there any lines I need in my config file? >>Are there any tools I can run to get more info? >> >>The array was built with LVM1 & 2.4.18, >>I'm now using LVM2/DM under 2.6.11.10 >> >>Also, It looks like it has done something, because if I try >>to deactivate it with "vgchange -P -a n vg1" I get: >> >> Partial mode. Incomplete volume groups will be activated read-only. >> 7 PV(s) found for VG vg1: expected 8 >> Logical volume (lv1) contains an incomplete mapping table. >> Can't deactivate volume group "vg1" with 1 open logical volume(s) >> >>Any help greatly appreciated. >>Kind regards, >>Tom >> >> >>_______________________________________________ >>linux-lvm mailing list >>linux-lvm@redhat.com >>https://www.redhat.com/mailman/listinfo/linux-lvm >>read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ >> >> > >=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > >Heinz Mauelshagen Red Hat GmbH >Consulting Development Engineer Am Sonnenhang 11 >Cluster and Storage Development 56242 Marienrachdorf > Germany >Mauelshagen@RedHat.com +49 2626 141200 > FAX 924446 >=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > >_______________________________________________ >linux-lvm mailing list >linux-lvm@redhat.com >https://www.redhat.com/mailman/listinfo/linux-lvm >read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [linux-lvm] vgchange partial mount fails 2005-11-08 11:06 ` Tom Robinson @ 2005-11-08 12:53 ` Heinz Mauelshagen 2005-11-08 14:24 ` Tom Robinson 0 siblings, 1 reply; 5+ messages in thread From: Heinz Mauelshagen @ 2005-11-08 12:53 UTC (permalink / raw) To: LVM general discussion and development; +Cc: hjm Hrm, the mapping of the first segment to /dev/cdrom looks very bogus. That would eyplain why there's no superblock to be found. DO you have a metadata archive reflecting a correct mapping ? Heinz On Tue, Nov 08, 2005 at 11:06:09AM +0000, Tom Robinson wrote: > Heinz Mauelshagen wrote: > > >On Mon, Nov 07, 2005 at 10:12:32PM +0000, Tom Robinson wrote: > > > > > >>Hi, > >> > >>I'm trying to do a partial mount of a VG in order to rescue data from it > >>(the last of the 8 PVs has died) > >> > >>If I do vgchange -P -a y vg1 > >>It says: > >> > >>Partial mode. Incomplete volume groups will be activated read-only. > >>7 PV(s) found for VG vg1: expected 8 > >>Logical volume (lv1) contains an incomplete mapping table. > >>7 PV(s) found for VG vg1: expected 8 > >>Logical volume (lv1) contains an incomplete mapping table. > >>1 logical volume(s) in volume group "vg1" now active > >> > >>Which looks like it might have worked, but in /dev/mapper I have: > >> > >>crw-rw---- 1 root root 10, 63 May 30 02:48 control > >>brw------- 1 root root 254, 0 Oct 25 13:20 vg1-lv1 > >> > >>But I can't mount vg1-lv1 (its ext2 - but it says "must specify fs type). > >> > >> > > > >Looks like expected behaviour. > > > >You're likely missing the beginning of your filesystem which was mapped > >to the dead PV and the fs code fails to find its metadata > >(ie. superblock). > > > >Check with "lvdisplay -m /dev/vg1/lv1" > > > > > > Thanks for your response, Heinz, > > vaus root # lvdisplay -m /dev/vg1/lv1 > 7 PV(s) found for VG vg1: expected 8 > 7 PV(s) found for VG vg1: expected 8 > Volume group "vg1" not found > > Thing is, /dev/vg1/lv1 doesn't exist at all, > It used to, when everything was working. > Only /dev/mapper exists. > > I have had the server running for about 3 years, > and only added the last (dead) PV about 2 months ago > so would it still put the superblock there? > > Any suggestions at all on how to rescue any data? > > Oh, heres the first bit of output of lvdisplay -mP /dev/vg1/lv1 > if it helps: > > Partial mode. Incomplete volume groups will be activated read-only. > --- Logical volume --- > LV Name /dev/vg1/lv1 > VG Name vg1 > LV UUID 000000-0000-0000-0000-0000-0000-000000 > LV Write Access read/write > LV Status available > # open 1 > LV Size 1.51 TB > Current LE 49447 > Segments 7486 > Allocation normal > Read ahead sectors 1024 > Block device 254:0 > > --- Segments --- > Logical extent 0 to 4883: > Type linear > Physical volume /dev/cdrom > Physical extents 0 to 4883 > > Logical extent 4884 to 8545: > Type linear > Physical volume /dev/hdf > Physical extents 0 to 3661 > > Logical extent 8546 to 12051: > Type linear > Physical volume /dev/hde4 > Physical extents 0 to 3505 > > Logical extent 12052 to 19530: > Type linear > Physical volume /dev/hdh > Physical extents 0 to 7478 > > Logical extent 19531 to 27009: > Type linear > Physical volume /dev/hda > Physical extents 0 to 7478 > > Logical extent 27010 to 34488: > Type linear > Physical volume /dev/hdb > Physical extents 0 to 7478 > > Logical extent 34489 to 41967: > Type linear > Physical volume /dev/hdc > Physical extents 0 to 7478 > > Logical extent 41968 to 41968: > Type linear > Physical volume Missing > > Logical extent 41969 to 41969: > Type linear > Physical volume Missing > > etc...... > > > Regards, > Tom > > > > > > > > > > > > > > > > > > >Regards, > >Heinz -- The LVM Guy -- > > > > > > > vaus root # lvdisplay -m /dev/vg1/lv1 > 7 PV(s) found for VG vg1: expected 8 > 7 PV(s) found for VG vg1: expected 8 > Volume group "vg1" not found > > > > > >>What is wrong? Have I misconfigured lvm / dm? > >>are there any lines I need in my config file? > >>Are there any tools I can run to get more info? > >> > >>The array was built with LVM1 & 2.4.18, > >>I'm now using LVM2/DM under 2.6.11.10 > >> > >>Also, It looks like it has done something, because if I try > >>to deactivate it with "vgchange -P -a n vg1" I get: > >> > >>Partial mode. Incomplete volume groups will be activated read-only. > >>7 PV(s) found for VG vg1: expected 8 > >>Logical volume (lv1) contains an incomplete mapping table. > >>Can't deactivate volume group "vg1" with 1 open logical volume(s) > >> > >>Any help greatly appreciated. > >>Kind regards, > >>Tom > >> > >> > >>_______________________________________________ > >>linux-lvm mailing list > >>linux-lvm@redhat.com > >>https://www.redhat.com/mailman/listinfo/linux-lvm > >>read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > >> > >> > >_______________________________________________ > >linux-lvm mailing list > >linux-lvm@redhat.com > >https://www.redhat.com/mailman/listinfo/linux-lvm > >read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > > > > > > > _______________________________________________ > linux-lvm mailing list > linux-lvm@redhat.com > https://www.redhat.com/mailman/listinfo/linux-lvm > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- Heinz Mauelshagen Red Hat GmbH Consulting Development Engineer Am Sonnenhang 11 Cluster and Storage Development 56242 Marienrachdorf Germany Mauelshagen@RedHat.com +49 2626 141200 FAX 924446 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [linux-lvm] vgchange partial mount fails 2005-11-08 12:53 ` Heinz Mauelshagen @ 2005-11-08 14:24 ` Tom Robinson 0 siblings, 0 replies; 5+ messages in thread From: Tom Robinson @ 2005-11-08 14:24 UTC (permalink / raw) To: LVM general discussion and development; +Cc: hjm Yeah, the cdrom thing I admit isn't great :) but it's always been there and it works. - since I built the 2.6 gentoo linux system, I just plugged all the old LVM one disks in and everything seemed to work. Archive and backup options are both on, but the only files in these directories contain the last reboot or something, which doesnt include the missing PV. No files in backup, but in /etc/lvm/archive: vaus lvm # ls -l /etc/lvm/archive/ total 2584 -rw------- 1 root root 1318506 Oct 25 13:17 vg1_00000.vg -rw------- 1 root root 1318506 Oct 25 13:37 vg1_00001.vg These files are identical apart from their creation time, and contain: ## snip ## contents = "Text Format Volume Group" version = 1 description = "Created *before* executing 'vgreduce --removemissing vg1'" creation_host = "vaus" # Linux vaus 2.6.11.10 #2 SMP Mon May 30 02:46:52 GMT 2005 i686 creation_time = 1130246262 # Tue Oct 25 13:17:42 2005 vg1 { id = "TzgIiD-ffy2-27aJ-et60-wQVa-TJwW-J4tFiH" seqno = 0 status = ["RESIZEABLE", "PARTIAL", "READ"] system_id = "vaus.tnet.com1096327806" extent_size = 65536 # 32 Megabytes max_lv = 256 max_pv = 256 physical_volumes { pv0 { id = "ofE07R-sevF-QJp0-xJ2k-Ga3z-fkIW-SDsS3F" device = "/dev/hda" # Hint only status = ["ALLOCATABLE"] pe_start = 65920 pe_count = 7479 # 233.719 Gigabytes } ## snip ## And follows for pv0 -> pv6 (pv7 not mentioned) Then follows: ## snip ## logical_volumes { lv1 { id = "000000-0000-0000-0000-0000-0000-000000" status = ["READ", "WRITE", "VISIBLE"] allocation_policy = "normal" read_ahead = 1024 segment_count = 7486 segment1 { start_extent = 0 extent_count = 4884 # 152.625 Gigabytes type = "striped" stripe_count = 1 # linear stripes = [ "pv2", 0 ] } segment2 { start_extent = 4884 extent_count = 3662 # 114.438 Gigabytes type = "striped" stripe_count = 1 # linear stripes = [ "pv5", 0 ] } ## snip ## Etc, for a _lot_ of segments, some of the segments say stripes = [ "Missing", 0 ] for the bits on the missing PV. There is quite a lot of stuff in this archive, Is it enough to somehow use to read the odd file? (something is better than nothing). Once again, I really appreciate the help you have given me. Kind regards, Tom Heinz Mauelshagen wrote: >Hrm, > >the mapping of the first segment to /dev/cdrom looks very bogus. >That would eyplain why there's no superblock to be found. > >DO you have a metadata archive reflecting a correct mapping ? > >Heinz > >On Tue, Nov 08, 2005 at 11:06:09AM +0000, Tom Robinson wrote: > > >>Heinz Mauelshagen wrote: >> >> >> >>>On Mon, Nov 07, 2005 at 10:12:32PM +0000, Tom Robinson wrote: >>> >>> >>> >>> >>>>Hi, >>>> >>>>I'm trying to do a partial mount of a VG in order to rescue data from it >>>>(the last of the 8 PVs has died) >>>> >>>>If I do vgchange -P -a y vg1 >>>>It says: >>>> >>>>Partial mode. Incomplete volume groups will be activated read-only. >>>>7 PV(s) found for VG vg1: expected 8 >>>>Logical volume (lv1) contains an incomplete mapping table. >>>>7 PV(s) found for VG vg1: expected 8 >>>>Logical volume (lv1) contains an incomplete mapping table. >>>>1 logical volume(s) in volume group "vg1" now active >>>> >>>>Which looks like it might have worked, but in /dev/mapper I have: >>>> >>>>crw-rw---- 1 root root 10, 63 May 30 02:48 control >>>>brw------- 1 root root 254, 0 Oct 25 13:20 vg1-lv1 >>>> >>>>But I can't mount vg1-lv1 (its ext2 - but it says "must specify fs type). >>>> >>>> >>>> >>>> >>>Looks like expected behaviour. >>> >>>You're likely missing the beginning of your filesystem which was mapped >>>to the dead PV and the fs code fails to find its metadata >>>(ie. superblock). >>> >>>Check with "lvdisplay -m /dev/vg1/lv1" >>> >>> >>> >>> >>Thanks for your response, Heinz, >> >>vaus root # lvdisplay -m /dev/vg1/lv1 >> 7 PV(s) found for VG vg1: expected 8 >> 7 PV(s) found for VG vg1: expected 8 >> Volume group "vg1" not found >> >>Thing is, /dev/vg1/lv1 doesn't exist at all, >>It used to, when everything was working. >>Only /dev/mapper exists. >> >>I have had the server running for about 3 years, >>and only added the last (dead) PV about 2 months ago >>so would it still put the superblock there? >> >>Any suggestions at all on how to rescue any data? >> >>Oh, heres the first bit of output of lvdisplay -mP /dev/vg1/lv1 >>if it helps: >> >> Partial mode. Incomplete volume groups will be activated read-only. >> --- Logical volume --- >> LV Name /dev/vg1/lv1 >> VG Name vg1 >> LV UUID 000000-0000-0000-0000-0000-0000-000000 >> LV Write Access read/write >> LV Status available >> # open 1 >> LV Size 1.51 TB >> Current LE 49447 >> Segments 7486 >> Allocation normal >> Read ahead sectors 1024 >> Block device 254:0 >> >> --- Segments --- >> Logical extent 0 to 4883: >> Type linear >> Physical volume /dev/cdrom >> Physical extents 0 to 4883 >> >> Logical extent 4884 to 8545: >> Type linear >> Physical volume /dev/hdf >> Physical extents 0 to 3661 >> >> Logical extent 8546 to 12051: >> Type linear >> Physical volume /dev/hde4 >> Physical extents 0 to 3505 >> >> Logical extent 12052 to 19530: >> Type linear >> Physical volume /dev/hdh >> Physical extents 0 to 7478 >> >> Logical extent 19531 to 27009: >> Type linear >> Physical volume /dev/hda >> Physical extents 0 to 7478 >> >> Logical extent 27010 to 34488: >> Type linear >> Physical volume /dev/hdb >> Physical extents 0 to 7478 >> >> Logical extent 34489 to 41967: >> Type linear >> Physical volume /dev/hdc >> Physical extents 0 to 7478 >> >> Logical extent 41968 to 41968: >> Type linear >> Physical volume Missing >> >> Logical extent 41969 to 41969: >> Type linear >> Physical volume Missing >> >>etc...... >> >> >>Regards, >> Tom >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >>>Regards, >>>Heinz -- The LVM Guy -- >>> >>> >>> >>> >>> >>vaus root # lvdisplay -m /dev/vg1/lv1 >> 7 PV(s) found for VG vg1: expected 8 >> 7 PV(s) found for VG vg1: expected 8 >> Volume group "vg1" not found >> >> >> >> >> >> >>>>What is wrong? Have I misconfigured lvm / dm? >>>>are there any lines I need in my config file? >>>>Are there any tools I can run to get more info? >>>> >>>>The array was built with LVM1 & 2.4.18, >>>>I'm now using LVM2/DM under 2.6.11.10 >>>> >>>>Also, It looks like it has done something, because if I try >>>>to deactivate it with "vgchange -P -a n vg1" I get: >>>> >>>>Partial mode. Incomplete volume groups will be activated read-only. >>>>7 PV(s) found for VG vg1: expected 8 >>>>Logical volume (lv1) contains an incomplete mapping table. >>>>Can't deactivate volume group "vg1" with 1 open logical volume(s) >>>> >>>>Any help greatly appreciated. >>>>Kind regards, >>>>Tom >>>> >>>> >>>>_______________________________________________ >>>>linux-lvm mailing list >>>>linux-lvm@redhat.com >>>>https://www.redhat.com/mailman/listinfo/linux-lvm >>>>read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ >>>> >>>> >>>> >>>> >>>_______________________________________________ >>>linux-lvm mailing list >>>linux-lvm@redhat.com >>>https://www.redhat.com/mailman/listinfo/linux-lvm >>>read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ >>> >>> >>> >>> >>> >>> >>_______________________________________________ >>linux-lvm mailing list >>linux-lvm@redhat.com >>https://www.redhat.com/mailman/listinfo/linux-lvm >>read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ >> >> > >=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > >Heinz Mauelshagen Red Hat GmbH >Consulting Development Engineer Am Sonnenhang 11 >Cluster and Storage Development 56242 Marienrachdorf > Germany >Mauelshagen@RedHat.com +49 2626 141200 > FAX 924446 >=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > >_______________________________________________ >linux-lvm mailing list >linux-lvm@redhat.com >https://www.redhat.com/mailman/listinfo/linux-lvm >read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/ > > > > ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2005-11-08 14:24 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2005-11-07 22:12 [linux-lvm] vgchange partial mount fails Tom Robinson 2005-11-08 10:00 ` Heinz Mauelshagen 2005-11-08 11:06 ` Tom Robinson 2005-11-08 12:53 ` Heinz Mauelshagen 2005-11-08 14:24 ` Tom Robinson
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).