From: Magnus Hyllander <mhylist1@hyllander.org>
To: LVM general discussion and development <linux-lvm@redhat.com>
Subject: Re: [linux-lvm] Different sizes being reported for logical volume after extend
Date: Sun, 11 Feb 2007 03:23:50 +0100 [thread overview]
Message-ID: <45CE7E36.5070609@hyllander.org> (raw)
In-Reply-To: <45AC032A.20104@hyllander.org>
I finally managed to solve my problem.
After some fiddling around with resize2fs, with which I changed the size
of the root partition back and forth between 4GB and 8GB a couple of
times, I actually ended up with the initial situation in which I again
saw that the size of /dev/VolGroup00/LogVol00 was 4GB when booting from
disk. So I started thinking, maybe the metadata is wrong somehow (even
though it looks right when booting with the rescue CD). I tried to run
"lvm vgcfgrestore VolGroup00", but could not do that because I got a
"Locking type 1" failure.
When I booted from the rescue CD, "lvm vgscan" followed by "lvm lvs"
showed 8GB. Then I tried successfully to run "lvm vgcfgrestore
VolGroup00". When I rebooted from disk again, the problem was solved!
I can't really say that I understand what was going on, why "lvm lvs"
showed different results when booting from disk or the rescue CD. Maybe
one of you knowledgeable people can offer an explanation?
Thanks,
Magnus
Magnus Hyllander wrote:
> Hi,
>
> I've been trying to solve this problem on my own but without success.
> One thing has changed though, and that is that the size of the logical
> volume is now 8GB both when I boot from the disk and from the rescue
> cd. So at least the logical volume seems to be alright now. But fsck
> still complains that the "device" is half the size of the file system.
> What "device" is fsck looking at, and why is the size wrong? I'd
> really appreciate some help!
>
> Thanks,
> Magnus
>
> Magnus Hyllander wrote:
>> Hi,
>>
>> I have a little problem with a logical volume: in short, the size of
>> the volume is different depending on if I boot from the FC5 rescue CD
>> or from the installed FC5.
>>
>> I have two mirrored disks. On the mirror I have created a logical
>> volume /dev/VolGroup00/LogVol00 which contains the root filesystem.
>> Initially I made the volume 4GB. Later I needed more space, so I
>> decided to extend the volume to 8GB. I booted from the FC5 rescue CD
>> and ran the following commands:
>>
>> dmraid -a y
>> lvm vgscan
>> lvm vgchange -a y
>> lvm lvextend -L +4G /dev/VolGroup00/LogVol00
>> fsck /dev/VolGroup00/LogVol00
>> resize2fs /dev/VolGroup00/LogVol00
>>
>> So far so good. Then I rebooted the system from disk and got the
>> following error:
>>
>> Checking filesystems
>> /dev/VolGroup00/LogVol00: The filesystem size (according to the
>> superblock) is 2097152 blocks
>> The physical size of the device is 1048576 blocks
>> Either the superblock or the partition table is likely to be corrupt!
>>
>> /dev/VolGroup/LogVol00: UNEXPECTED INCONSISTENCY, run fsck manually.
>>
>> I entered the system administration mode and checked the size of
>> /dev/VolGroup/LogVol00 with "lvm lvs": 4.00G
>> Strange... so I booted with the rescue CD again and checked the size
>> once more from the rescue environment: 8.00G.
>>
>> So it seems that when I boot the system normally it doesn't "see"
>> that the size of the logical volume has changed. Can someone explain
>> this, and hopefully help me fix the problem?
>>
>> /Magnus
>
> _______________________________________________
> linux-lvm mailing list
> linux-lvm@redhat.com
> https://www.redhat.com/mailman/listinfo/linux-lvm
> read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/
prev parent reply other threads:[~2007-02-11 2:24 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-11-30 20:39 [linux-lvm] Different sizes being reported for logical volume after extend Magnus Hyllander
2007-01-15 22:41 ` Magnus Hyllander
2007-02-11 2:23 ` Magnus Hyllander [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=45CE7E36.5070609@hyllander.org \
--to=mhylist1@hyllander.org \
--cc=linux-lvm@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).