public inbox for linux-m68k@lists.linux-m68k.org
 help / color / mirror / Atom feed
From: Michael Schmitz <schmitzmic@gmail.com>
To: geert@linux-m68k.org
Cc: linux-m68k@vger.kernel.org, Michael Schmitz <schmitz@debian.org>
Subject: [PATCH 11/12] m68k/atari: USB - add platform devices for EtherNAT/NetUSBee ISP1160 HCD
Date: Sat, 30 Mar 2013 13:27:51 +1300	[thread overview]
Message-ID: <1364603272-8148-12-git-send-email-schmitz@debian.org> (raw)
In-Reply-To: <1364603272-8148-1-git-send-email-schmitz@debian.org>

Add platform devices used by the isp116x-hcd driver for EtherNAT and
NetUSBee. Note that the NetUSBee also contains a RTL8019 Ethernet chip,
so its platform device is used to cover the EtherNEC case, too.
Register definitions thanks to David Galvez <dgalvez75@gmail.com>

Signed-off-by: Michael Schmitz <schmitz@debian.org>
---
 arch/m68k/atari/config.c |  131 ++++++++++++++++++++++++++++++++++++++++++++--
 1 files changed, 126 insertions(+), 5 deletions(-)

diff --git a/arch/m68k/atari/config.c b/arch/m68k/atari/config.c
index fdcd875..29ffc1a 100644
--- a/arch/m68k/atari/config.c
+++ b/arch/m68k/atari/config.c
@@ -32,6 +32,7 @@
 #include <linux/delay.h>
 #include <linux/ioport.h>
 #include <linux/platform_device.h>
+#include <linux/usb/isp116x.h>
 #include <linux/vt_kern.h>
 #include <linux/module.h>
 
@@ -690,8 +691,70 @@ static struct platform_device smc91x_device = {
 	.resource	= smc91x_resources,
 };
 
+/*
+ * ISP 1160 - using the isp116x-hcd module
+ */
+
+#define ATARI_USB_PHYS_ADDR	0x80000012
+#define ATARI_USB_IRQ		139
+
+static struct resource isp1160_resources[] = {
+	[0] = {
+		.name	= "isp1160-data",
+		.start	= ATARI_USB_PHYS_ADDR,
+		.end	= ATARI_USB_PHYS_ADDR + 0x1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.name	= "isp1160-regs",
+		.start	= ATARI_USB_PHYS_ADDR + 0x4,
+		.end	= ATARI_USB_PHYS_ADDR + 0x5,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.name	= "isp1160-irq",
+		.start	= ATARI_USB_IRQ,
+		.end	= ATARI_USB_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static void isp1160_delay(struct device *dev, int delay)
+{
+	ndelay(delay);
+}
+
+/* (DataBusWidth16|AnalogOCEnable|DREQOutputPolarity|DownstreamPort15KRSel ) */
+static struct isp116x_platform_data isp1160_platform_data = {
+	/* Enable internal resistors on downstream ports */
+	.sel15Kres		= 1,
+	/* On-chip overcurrent protection */
+	.oc_enable		= 1,
+	/* INT output polarity */
+	.int_act_high		= 1,
+	/* INT edge or level triggered */
+	.int_edge_triggered	= 0,
+
+	/* WAKEUP pin connected - NOT SUPPORTED  */
+	/* .remote_wakeup_connected = 0, */
+	/* Wakeup by devices on usb bus enabled */
+	.remote_wakeup_enable	= 0,
+	.delay			= isp1160_delay,
+};
+
+static struct platform_device isp1160_device = {
+	.name		= "isp116x-hcd",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(isp1160_resources),
+	.resource	= isp1160_resources,
+	.dev			= {
+		.platform_data	= &isp1160_platform_data,
+	},
+};
+
 static struct platform_device *atari_ethernat_devices[] __initdata = {
-	&smc91x_device
+	&smc91x_device,
+	&isp1160_device
 };
 
 /*
@@ -725,8 +788,66 @@ static struct platform_device rtl8019_device = {
 	.resource	= rtl8019_resources,
 };
 
-static struct platform_device *atari_ethernec_devices[] __initdata = {
-	&rtl8019_device
+/*
+ * NetUSBee: ISP1160 USB host adapter via ROM-port adapter
+ */
+
+#define ATARI_NETUSBEE_PHYS_ADDR	0xfffa8000
+#define ATARI_NETUSBEE_BASE		0x340
+#define ATARI_NETUSBEE_IRQ		IRQ_MFP_TIMER2
+
+static struct resource netusbee_resources[] = {
+	[0] = {
+		.name	= "isp1160-data",
+		.start	= ATARI_NETUSBEE_BASE,
+		.end	= ATARI_NETUSBEE_BASE + 0x1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.name	= "isp1160-regs",
+		.start	= ATARI_NETUSBEE_BASE + 0x20,
+		.end	= ATARI_NETUSBEE_BASE + 0x21,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.name	= "isp1160-irq",
+		.start	= ATARI_NETUSBEE_IRQ,
+		.end	= ATARI_NETUSBEE_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+/* (DataBusWidth16|AnalogOCEnable|DREQOutputPolarity|DownstreamPort15KRSel ) */
+static struct isp116x_platform_data netusbee_platform_data = {
+	/* Enable internal resistors on downstream ports */
+	.sel15Kres		= 1,
+	/* On-chip overcurrent protection */
+	.oc_enable		= 1,
+	/* INT output polarity */
+	.int_act_high		= 1,
+	/* INT edge or level triggered */
+	.int_edge_triggered	= 0,
+
+	/* WAKEUP pin connected - NOT SUPPORTED  */
+	/* .remote_wakeup_connected = 0, */
+	/* Wakeup by devices on usb bus enabled */
+	.remote_wakeup_enable	= 0,
+	.delay			= isp1160_delay,
+};
+
+static struct platform_device netusbee_device = {
+	.name		= "isp116x-hcd",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(netusbee_resources),
+	.resource	= netusbee_resources,
+	.dev			= {
+		.platform_data	= &netusbee_platform_data,
+	},
+};
+
+static struct platform_device *atari_netusbee_devices[] __initdata = {
+	&rtl8019_device,
+	&netusbee_device
 };
 
 int __init atari_platform_init(void)
@@ -754,8 +875,8 @@ int __init atari_platform_init(void)
 		unsigned char *enec_virt;
 		enec_virt = (unsigned char *)ioremap((ATARI_ETHERNEC_PHYS_ADDR), 0xf);
 		if (hwreg_present(enec_virt)) {
-			error = platform_add_devices(atari_ethernec_devices,
-						ARRAY_SIZE(atari_ethernec_devices));
+			error = platform_add_devices(atari_netusbee_devices,
+						ARRAY_SIZE(atari_netusbee_devices));
 			if (error && !rv)
 				rv = error;
 		}
-- 
1.7.0.4

  parent reply	other threads:[~2013-03-30  0:29 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-03-30  0:27 Atari Ethernet/USB paches for m68k-queue and upstream, refactored timer D interrupt patch Michael Schmitz
2013-03-30  0:27 ` [PATCH 01/12] m68k/atari: ROM port ISA adapter support Michael Schmitz
2013-03-30  0:27 ` [PATCH 02/12] m68k/irq: Add handle_polled_irq() for timer based soft interrupts Michael Schmitz
2013-03-30  0:27 ` [PATCH 03/12] m68k/atari: use dedicated irq_chip for timer D interrupts Michael Schmitz
2013-03-30  0:27 ` [PATCH 04/12] m68k/atari: use polled interrupt handler " Michael Schmitz
2013-03-30  0:27 ` [PATCH 05/12] m68k/atari: EtherNAT - platform device and IRQ support code Michael Schmitz
2013-03-30  0:27 ` [PATCH 06/12] m68k/atari: EtherNEC - add platform device support Michael Schmitz
2013-03-30  0:27 ` [PATCH 07/12] m68k/atari: EtherNAT - ethernet support - new driver (smc91x) Michael Schmitz
2013-03-30  0:27 ` [PATCH 08/12] m68k/atari: EtherNEC - ethernet support - new driver (ne.c) Michael Schmitz
2013-03-30  0:27 ` [PATCH 09/12] m68k/atari: EtherNAT - add interrupt chip definition for CPLD interrupts Michael Schmitz
2013-03-30  0:27 ` [PATCH 10/12] m68k: Implement ndelay() based on the existing udelay() logic Michael Schmitz
2013-03-30  0:27 ` Michael Schmitz [this message]
2013-03-30  0:27 ` [PATCH 12/12] m68k/atari: USB - add ISP1160 USB host controller support Michael Schmitz
  -- strict thread matches above, loose matches on Subject: below --
2013-04-06  0:26 [PATCH 0/13] Atari EtherNAT/EtherNEC/NetUSBee support Michael Schmitz
2013-04-06  0:26 ` [PATCH 11/12] m68k/atari: USB - add platform devices for EtherNAT/NetUSBee ISP1160 HCD Michael Schmitz
2013-08-26 10:18   ` Geert Uytterhoeven
2013-09-04 12:26     ` Michael Schmitz
2013-09-04 13:23       ` Geert Uytterhoeven
2013-09-07 11:48         ` Michael Schmitz

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1364603272-8148-12-git-send-email-schmitz@debian.org \
    --to=schmitzmic@gmail.com \
    --cc=geert@linux-m68k.org \
    --cc=linux-m68k@vger.kernel.org \
    --cc=schmitz@debian.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox