Re: [linux-dvb] Duel Hauppauge HVR-1600

["Tom Moore" <htmoore@comcast.net>]

Thanks Andy for the reply.

I did what you said and now I'm getting an memory error message when booting


The message reads:
Initrd extends beyond end of memory (0x37fef23a > 0x30000000)

I tried lowering the amount but anything over 128M and I get the error
message.

Here is my config file:
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this file
# NOTICE:  You have a /boot partition.  This means that
#          all kernel and initrd paths are relative to /boot/, eg.
#          root (hd0,0)
#          kernel /vmlinuz-version ro root=/dev/VolGroup00/LogVol00
#          initrd /initrd-version.img
#boot=/dev/sda
default=0
timeout=5
splashimage=(hd0,0)/grub/splash.xpm.gz
hiddenmenu
title MythDora (2.6.24.4-64.fc8)
	root (hd0,0)
	kernel /vmlinuz-2.6.24.4-64.fc8 ro root=/dev/VolGroup00/LogVol00
rhgb quiet vmalloc=256M
	initrd /initrd-2.6.24.4-64.fc8.img

-----Original Message-----
From: Andy Walls [mailto:awalls@radix.net] 
Sent: Tuesday, October 14, 2008 7:16 PM
To: Tom Moore
Cc: linux-dvb@linuxtv.org
Subject: Re: [linux-dvb] Duel Hauppauge HVR-1600

On Tue, 2008-10-14 at 18:43 -0500, Tom Moore wrote:
> I just bought two Hauppauge HVR-1600 cards and I'm trying to set them
> up in 
> 
> Mythdorra 5. I have the cx18 drivers installed but it is only
> initializing one 
> 
> card. I'm getting the following message when I do a dmesg | grep cx18.
> Has 
> 
> anyone ran accross this problem before with duel cards of the same
> model and if 
> 
> so, how do I fix it? Any help will be greatly appreciated.
> 
>  
> 
> Thanks,
> 
> Tom Moore
> 
> Houston, TX
> 
>  
> 
> dmesg | grep cx18
> 
> cx18:  Start initialization, version 1.0.1

> cx18-1: Initializing card #1
> 
> cx18-1: Autodetected Hauppauge card
> 
> cx18-1: Unreasonably low latency timer, setting to 64 (was 32)
> 
> cx18-1: ioremap failed, perhaps increasing __VMALLOC_RESERVE in page.h
> 
> cx18-1: or disabling CONFIG_HIGHMEM4G into the kernel would help
> 
> cx18-1: Error -12 on initialization
> 
> cx18: probe of 0000:02:04.0 failed with error -12
> 
> cx18:  End initialization
> 

You're out of vmalloc address space.  Each cx18 needs 64 MB of vmalloc
space for MMIO mappings.

Do this:

$ cat /proc/meminfo | grep Vmalloc

Edit your bootloader's config file to add a 'vmalloc=xxxM' option to
your kernel commandline.  Use a value that is 128M greater than your
current VmallocTotal. 


Regards,
Andy




_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb