[linux-dvb] i can't make my Lifeview trio CARDBUS works.

[linux-dvb] i can't make my Lifeview trio CARDBUS works.

[cherOKe]

Hi, it's my first timer here, i'm cheroke from spain. 

I,ve trying to istall y lifeview trio several times with no good
results, the only that I've made works it's analog tv without sound :(.

the last thing that i've made eforo write this was follow the
instruccions that I found here:

http://www.selenic.com/mercurial/wiki/index.cgi/UnixInstall#head-a2d5313c6a815573ef51192eea7fa0deed53cca3

after that i made this :

http://www.linuxtv.org/repo/

i've UNKNOWN/GENERIC in the $dmesg exit and i tryed to unload de modules
and reload it, but when i made:
$sudo rmmod saa7134_alsa saa7134-dvb saa7134
the exit was.
ERROR: Module saa7134_alsa does not exist in /proc/modules
ERROR: Module saa7134_dvb does not exist in /proc/modules

then i tryed to load de modules with:

$ sudo modprobe saa7134 card=84
$ sudo modprobe saa7134_alsa
$ sudo modprobe saa7134-dvb

but in the first sentence....

ERROR: Module saa7134_alsa does not exist in /proc/modules
ERROR: Module saa7134_dvb does not exist in /proc/modules
ERROR: Module saa7134 does not exist in /proc/modules
cheroke@fugitif:~$ sudo modprobe saa7134 card=84
WARNING: Error inserting videobuf_core (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/videobuf-core.ko): Invalid module format
WARNING: Error inserting videobuf_dma_sg (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/videobuf-dma-sg.ko): Unknown symbol in module, or unknown parameter (see dmesg)
WARNING: Error inserting videobuf_core (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/videobuf-core.ko): Invalid module format
WARNING: Error inserting videobuf_dma_sg (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/videobuf-dma-sg.ko): Unknown symbol in module, or unknown parameter (see dmesg)
FATAL: Error inserting saa7134 (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/saa7134/saa7134.ko): Unknown symbol in module, or unknown parameter (see dmesg)
FATAL: Error running install command for saa7134

this is my $ dmesg |grep saa exit now: 
[   42.744505] saa7130/34: v4l2 driver version 0.2.14 loaded
[   42.744616] saa7133[0]: found at 0000:09:00.0, rev: 209, irq: 18,
latency: 0, mmio: 0x90000000
[   42.744637] saa7133[0]: subsystem: 5168:0520, board: UNKNOWN/GENERIC
[card=0,autodetected]
[   42.744650] saa7133[0]: board init: gpio is 210000
[   42.787696] saa7133[0]: i2c eeprom 00: 68 51 20 05 54 20 1c 00 43 43
a9 1c 55 d2 b2 92
[   42.787714] saa7133[0]: i2c eeprom 10: 00 00 60 0a ff 20 ff ff ff ff
ff ff ff ff ff ff
[   42.787730] saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff
01 02 ff ff ff ff
[   42.787746] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[   42.787762] saa7133[0]: i2c eeprom 40: ff 00 10 c0 96 12 08 00 c2 96
c6 1c 16 3a 15 ff
[   42.787778] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[   42.787794] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[   42.787809] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[   42.788327] saa7133[0]: registered device video0 [v4l2]
[   42.788357] saa7133[0]: registered device vbi0
[25942.933953] saa7134_dvb: Unknown symbol videobuf_dvb_unregister
[25942.934022] saa7134_dvb: Unknown symbol videobuf_dvb_register
[34073.218239] saa7134: disagrees about version of symbol
videobuf_streamoff
[34073.218245] saa7134: Unknown symbol videobuf_streamoff
[34073.218377] saa7134: disagrees about version of symbol
videobuf_poll_stream
videobuf_mmap_free .......
...................  ---- and much more ---

Could someone help me or orientate a little?

Sorry for the big test, thanks: cherOKe




_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

Re: [linux-dvb] i can't make my Lifeview trio CARDBUS works.

[hermann pitton]

Hi,

Am Donnerstag, den 03.04.2008, 02:31 +0200 schrieb cherOKe:
> Hi, it's my first timer here, i'm cheroke from spain. 
> 
> I,ve trying to istall y lifeview trio several times with no good
> results, the only that I've made works it's analog tv without sound :(.

for devices without analog sound out you need a helper application like
"sox -c 2 -s -w -r 32000 -t ossdsp /dev/dsp1 -t ossdsp -w -r 48000 /dev/dsp"
to get the sound from here assumed saa7134-alsa device /dev/dsp1 to your sound card.

Only mplayer and mencoder support this directly from the saa7134-alsa dsp with immediatemode=0.

Sample commands could look like.

/usr/local/bin/mplayer -v tv:// -vf pp=lb -tv driver=v4l2:norm=PAL:input=0:alsa:adevice=hw.1,0:forceaudio:immediatemode=0:audiorate=32000:amode=1:width=640:height=480:outfmt=yuy2:device=/dev/video0:chanlist=europe-west:channel=E9

/usr/local/bin/mencoder -v tv:// -tv driver=v4l2:device=/dev/video0:width=640:height=480:chanlist=europe-west:alsa:adevice=hw.1,0:audiorate=32000:amode=1:forceaudio:volume=95:immediatemode=0:norm=PAL -ovc lavc -lavcopts vcodec=mpeg4:vbitrate=3600 -vf pp=lb -oac mp3lame -lameopts cbr:br=128:mode=0 -o mytest.avi

> the last thing that i've made eforo write this was follow the
> instruccions that I found here:
> 
> http://www.selenic.com/mercurial/wiki/index.cgi/UnixInstall#head-a2d5313c6a815573ef51192eea7fa0deed53cca3
> 
> after that i made this :
> 
> http://www.linuxtv.org/repo/

OK, I assume you have a recent v4l-dvb master copy now.

> i've UNKNOWN/GENERIC in the $dmesg exit and i tryed to unload de modules
> and reload it, but when i made:
> $sudo rmmod saa7134_alsa saa7134-dvb saa7134
> the exit was.
> ERROR: Module saa7134_alsa does not exist in /proc/modules
> ERROR: Module saa7134_dvb does not exist in /proc/modules
> 
> then i tryed to load de modules with:
> 
> $ sudo modprobe saa7134 card=84
> $ sudo modprobe saa7134_alsa
> $ sudo modprobe saa7134-dvb
> 
> but in the first sentence....
> 
> ERROR: Module saa7134_alsa does not exist in /proc/modules
> ERROR: Module saa7134_dvb does not exist in /proc/modules
> ERROR: Module saa7134 does not exist in /proc/modules
> cheroke@fugitif:~$ sudo modprobe saa7134 card=84
> WARNING: Error inserting videobuf_core (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/videobuf-core.ko): Invalid module format
> WARNING: Error inserting videobuf_dma_sg (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/videobuf-dma-sg.ko): Unknown symbol in module, or unknown parameter (see dmesg)
> WARNING: Error inserting videobuf_core (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/videobuf-core.ko): Invalid module format
> WARNING: Error inserting videobuf_dma_sg (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/videobuf-dma-sg.ko): Unknown symbol in module, or unknown parameter (see dmesg)
> FATAL: Error inserting saa7134 (/lib/modules/2.6.24-12-generic/kernel/drivers/media/video/saa7134/saa7134.ko): Unknown symbol in module, or unknown parameter (see dmesg)
> FATAL: Error running install command for saa7134
> 
> this is my $ dmesg |grep saa exit now: 
> [   42.744505] saa7130/34: v4l2 driver version 0.2.14 loaded
> [   42.744616] saa7133[0]: found at 0000:09:00.0, rev: 209, irq: 18,
> latency: 0, mmio: 0x90000000
> [   42.744637] saa7133[0]: subsystem: 5168:0520, board: UNKNOWN/GENERIC
........................................^^^^^^^^^
> [card=0,autodetected]
> [   42.744650] saa7133[0]: board init: gpio is 210000
.................................................^^^^^^
> [   42.787696] saa7133[0]: i2c eeprom 00: 68 51 20 05 54 20 1c 00 43 43
> a9 1c 55 d2 b2 92
> [   42.787714] saa7133[0]: i2c eeprom 10: 00 00 60 0a ff 20 ff ff ff ff
> ff ff ff ff ff ff
> [   42.787730] saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff
> 01 02 ff ff ff ff
> [   42.787746] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [   42.787762] saa7133[0]: i2c eeprom 40: ff 00 10 c0 96 12 08 00 c2 96
> c6 1c 16 3a 15 ff
> [   42.787778] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [   42.787794] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [   42.787809] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [   42.788327] saa7133[0]: registered device video0 [v4l2]
> [   42.788357] saa7133[0]: registered device vbi0
> [25942.933953] saa7134_dvb: Unknown symbol videobuf_dvb_unregister
> [25942.934022] saa7134_dvb: Unknown symbol videobuf_dvb_register
> [34073.218239] saa7134: disagrees about version of symbol
> videobuf_streamoff
> [34073.218245] saa7134: Unknown symbol videobuf_streamoff
> [34073.218377] saa7134: disagrees about version of symbol
> videobuf_poll_stream
> videobuf_mmap_free .......
> ...................  ---- and much more ---
> 
> Could someone help me or orientate a little?

On older kernels, like 2.6.20, a simple "make" does not make all it
seems, also "make allmodconfig" doesn't work. You get all bttv, cx88,
saa7134 related and others not built. This might be the case here.

This results in a mixture of incompatible old and new modules after
"make install".

Try "make distclean" and then "make xconfig" and enable all missing
modules, also go through dvb and check that the related frontends
tda10045/46 and tda10086 and the isl6421 are ready, see it with
customize dvb froontends. In short enable all you can and if possible
always as modules. Then "make".

If installing first time on an older kernel, try to make sure you have 
really all older *.ko removed from /lib/modules/uname -r/kernel/drivers/media

With "make rmmod" you might not be able to unload all modules and might
try to get the rest with "modprobe -vr" or must reboot later.

Do "make rminstall", this should remove all *.ko from the media folder,
but check with "ls -R |grep .ko" there and remove/delete any remaining
module. Do "make install". Reboot if there are any related modules still
loaded.

If you want to test DVB-S, it is best to put
"options saa7134-dvb use_frontend=1" in /etc/modprobe.conf or what your
distribution uses else for module options and "depmod -a".

Also put "options saa7134 card=84 latency=64" something there to avoid
card=0 on boot, but from now on everything else should work too.

If it should have a remote, support is not in tree, if it has radio
support, please test. Please report, that we might be able to add it to
auto detection. We have one previous report for now and that cardbus
version was functional so far.

Happy testing,

Hermann












--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

Re: [linux-dvb] i can't make my Lifeview trio CARDBUS works.

[hermann pitton]

Am Freitag, den 04.04.2008, 01:14 +0200 schrieb cherOKe:
> El jue, 03-04-2008 a las 22:14 +0200, hermann pitton escribió:
> > Hi,
> > 
> > Am Donnerstag, den 03.04.2008, 02:31 +0200 schrieb cherOKe:
> > > Hi, it's my first timer here, i'm cheroke from spain. 
> > > 
> > > I,ve trying to istall y lifeview trio several times with no good
> > > results, the only that I've made works it's analog tv without sound :(.
> > 
> > for devices without analog sound out you need a helper application like
> > "sox -c 2 -s -w -r 32000 -t ossdsp /dev/dsp1 -t ossdsp -w -r 48000 /dev/dsp"
> > to get the sound from here assumed saa7134-alsa device /dev/dsp1 to your sound card.
> > 
> > Only mplayer and mencoder support this directly from the saa7134-alsa dsp with immediatemode=0.
> > 
> > Sample commands could look like.
> > 
> > /usr/local/bin/mplayer -v tv:// -vf pp=lb -tv driver=v4l2:norm=PAL:input=0:alsa:adevice=hw.1,0:forceaudio:immediatemode=0:audiorate=32000:amode=1:width=640:height=480:outfmt=yuy2:device=/dev/video0:chanlist=europe-west:channel=E9
> > 
> > /usr/local/bin/mencoder -v tv:// -tv driver=v4l2:device=/dev/video0:width=640:height=480:chanlist=europe-west:alsa:adevice=hw.1,0:audiorate=32000:amode=1:forceaudio:volume=95:immediatemode=0:norm=PAL -ovc lavc -lavcopts vcodec=mpeg4:vbitrate=3600 -vf pp=lb -oac mp3lame -lameopts cbr:br=128:mode=0 -o mytest.avi
> ...............
> > 
> > OK, I assume you have a recent v4l-dvb master copy now.
> > 
> ...............
> > On older kernels, like 2.6.20, a simple "make" does not make all it
> > seems, also "make allmodconfig" doesn't work. You get all bttv, cx88,
> > saa7134 related and others not built. This might be the case here.
> > 
> > This results in a mixture of incompatible old and new modules after
> > "make install".
> > 
> > Try "make distclean" and then "make xconfig" and enable all missing
> > modules, also go through dvb and check that the related frontends
> > tda10045/46 and tda10086 and the isl6421 are ready, see it with
> > customize dvb froontends. In short enable all you can and if possible
> > always as modules. Then "make".
> > 
> > If installing first time on an older kernel, try to make sure you have 
> > really all older *.ko removed from /lib/modules/uname -r/kernel/drivers/media
> > 
> > With "make rmmod" you might not be able to unload all modules and might
> > try to get the rest with "modprobe -vr" or must reboot later.
> > 
> > Do "make rminstall", this should remove all *.ko from the media folder,
> > but check with "ls -R |grep .ko" there and remove/delete any remaining
> > module. Do "make install". Reboot if there are any related modules still
> > loaded.
> > 
> > If you want to test DVB-S, it is best to put
> > "options saa7134-dvb use_frontend=1" in /etc/modprobe.conf or what your
> > distribution uses else for module options and "depmod -a".
> > 
> > Also put "options saa7134 card=84 latency=64" something there to avoid
> > card=0 on boot, but from now on everything else should work too.
> > 
> > If it should have a remote, support is not in tree, if it has radio
> > support, please test. Please report, that we might be able to add it to
> > auto detection. We have one previous report for now and that cardbus
> > version was functional so far.
> > 
> > Happy testing,
> > 
> > Hermann
> > 
> Hi, 
> Thanks you for responding, i'll try to digest all the information yo give me, and testing.
> I'll report results as soon i have.
> I'm using Ubuntu 8.04 (development branch) kernel2.6.24-12-generic.

Hi,

yes, that is true.

Had a first look 24 hours back and missed the 2.6.24 now, but the
pattern should still be valid for _all_ supported kernels, but 2.6.24 is
not exactly in question ;)

You have some nice module mess anyway.

Cheers,
Hermann




--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list