IR Receiver on an Tevii S470

IR Receiver on an Tevii S470

[Matthias Fechner]

Hi,

I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got it 
running with the driver from:
http://mercurial.intuxication.org/hg/s2-liplianin

But I was not successfull in got the IR receiver working.
It seems that it is not supported yet by the driver.

Is there maybe some code available to get the IR receiver with evdev 
running?

Thanks a lot,
Matthias

Re: IR Receiver on an Tevii S470

[Matthias Fechner]

Hi,

Matthias Fechner schrieb:
> I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got it 
> running with the driver from:
> http://mercurial.intuxication.org/hg/s2-liplianin
> 
> But I was not successfull in got the IR receiver working.
> It seems that it is not supported yet by the driver.
> 
> Is there maybe some code available to get the IR receiver with evdev 
> running?

it seems to be not the correct mailing list, could some please suggest 
where I can ask that question?

Bye
Matthias

-- 

"Programming today is a race between software engineers striving to
build bigger and better idiot-proof programs, and the universe trying to
produce bigger and better idiots. So far, the universe is winning." --
Rich Cook

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Sat, 2009-11-21 at 18:10 +0100, Matthias Fechner wrote:
> Hi,
> 
> Matthias Fechner schrieb:
> > I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got it 
> > running with the driver from:
> > http://mercurial.intuxication.org/hg/s2-liplianin
> > 
> > But I was not successfull in got the IR receiver working.
> > It seems that it is not supported yet by the driver.
> > 
> > Is there maybe some code available to get the IR receiver with evdev 
> > running?

What bridge chip does the TeVii S470 use: a CX23885, CX23887, or
CX23888?

Does the TeVii S470 have a separate microcontroller chip for IR
somewhere on the board, or does it not have one?  (If you can't tell,
just provide a list of the chip markings on the board.)


If the card is using the built in IR controller of the CX23888 than that
should be pretty easy to get working, we'll just need you to do some
experimentation with a patch.

If the card is using the built in IR controller in the CX23885, then
you'll have to wait until I port my CX23888 IR controller changes to
work with the IR controller in the CX23885.  That should be somewhat
straightforward, but will take time.  Then we'll still need you to
experiment with a patch.

If the card is using a separate IR microcontroller, I'm not sure where
to begin.... :P

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Jonas Kvinge]

Andy Walls wrote:
> On Sat, 2009-11-21 at 18:10 +0100, Matthias Fechner wrote:
>> Hi,
>>
>> Matthias Fechner schrieb:
>>> I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got it 
>>> running with the driver from:
>>> http://mercurial.intuxication.org/hg/s2-liplianin
>>>
>>> But I was not successfull in got the IR receiver working.
>>> It seems that it is not supported yet by the driver.
>>>
>>> Is there maybe some code available to get the IR receiver with evdev 
>>> running?
> 
> What bridge chip does the TeVii S470 use: a CX23885, CX23887, or
> CX23888?
> 
> Does the TeVii S470 have a separate microcontroller chip for IR
> somewhere on the board, or does it not have one?  (If you can't tell,
> just provide a list of the chip markings on the board.)
> 
> 
> If the card is using the built in IR controller of the CX23888 than that
> should be pretty easy to get working, we'll just need you to do some
> experimentation with a patch.
> 
> If the card is using the built in IR controller in the CX23885, then
> you'll have to wait until I port my CX23888 IR controller changes to
> work with the IR controller in the CX23885.  That should be somewhat
> straightforward, but will take time.  Then we'll still need you to
> experiment with a patch.
> 
> If the card is using a separate IR microcontroller, I'm not sure where
> to begin.... :P
> 
> Regards,
> Andy
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 

According to the Wiki it's a cx23885. Looks like the IR is on the chip.
It's in the Wiki: http://linuxtv.org/wiki/index.php/TeVii_S470

Tevii is listing the card as supported in Linux with ti's own s2api
driver download, its here: http://www.tevii.com/Support.asp

Jonas

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 21 ноября 2009 22:41:42 Andy Walls wrote:
> On Sat, 2009-11-21 at 18:10 +0100, Matthias Fechner wrote:
> > Hi,
> >
> > Matthias Fechner schrieb:
> > > I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got it
> > > running with the driver from:
> > > http://mercurial.intuxication.org/hg/s2-liplianin
> > >
> > > But I was not successfull in got the IR receiver working.
> > > It seems that it is not supported yet by the driver.
> > >
> > > Is there maybe some code available to get the IR receiver with evdev
> > > running?
>
> What bridge chip does the TeVii S470 use: a CX23885, CX23887, or
> CX23888?
>
> Does the TeVii S470 have a separate microcontroller chip for IR
> somewhere on the board, or does it not have one?  (If you can't tell,
> just provide a list of the chip markings on the board.)
>
>
> If the card is using the built in IR controller of the CX23888 than that
> should be pretty easy to get working, we'll just need you to do some
> experimentation with a patch.
>
> If the card is using the built in IR controller in the CX23885, then
> you'll have to wait until I port my CX23888 IR controller changes to
> work with the IR controller in the CX23885.  That should be somewhat
> straightforward, but will take time.  Then we'll still need you to
> experiment with a patch.
>
> If the card is using a separate IR microcontroller, I'm not sure where
> to begin.... :P
>
> Regards,
> Andy
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
It's cx23885 definitely.
Remote uses NEC codes.
In any case I can test.

-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Sun, 2009-11-22 at 03:03 +0200, Igor M. Liplianin wrote:
> On 21 ноября 2009 22:41:42 Andy Walls wrote:
> > On Sat, 2009-11-21 at 18:10 +0100, Matthias Fechner wrote:
> > > Hi,
> > >
> > > Matthias Fechner schrieb:
> > > > I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got it
> > > > running with the driver from:
> > > > http://mercurial.intuxication.org/hg/s2-liplianin
> > > >
> > > > But I was not successfull in got the IR receiver working.
> > > > It seems that it is not supported yet by the driver.
> > > >
> > > > Is there maybe some code available to get the IR receiver with evdev
> > > > running?
> >
> > What bridge chip does the TeVii S470 use: a CX23885, CX23887, or
> > CX23888?
> >
> > Does the TeVii S470 have a separate microcontroller chip for IR
> > somewhere on the board, or does it not have one?  (If you can't tell,
> > just provide a list of the chip markings on the board.)
> >
> >
> > If the card is using the built in IR controller of the CX23888 than that
> > should be pretty easy to get working, we'll just need you to do some
> > experimentation with a patch.
> >
> > If the card is using the built in IR controller in the CX23885, then
> > you'll have to wait until I port my CX23888 IR controller changes to
> > work with the IR controller in the CX23885.  That should be somewhat
> > straightforward, but will take time.  Then we'll still need you to
> > experiment with a patch.
> >
> > If the card is using a separate IR microcontroller, I'm not sure where
> > to begin.... :P
> >
> > Regards,
> > Andy
> >
> It's cx23885 definitely.
> Remote uses NEC codes.

OK.  Things I have to do:

1. Add v4l2_subdev_ir_ops for the CX23885 to the cx25840 module.  Much
of this code will look like the cx23885/cx23888-ir.[ch] code, except a
little nicer when accessing I2C bus registers.

2. Add NEC pulse decoding to cx23885/cx23885-input.c.  This will be new
work, as right now the cx23885 driver only performs RC-5 decoding.

3. Add IR intiialization for the TeVii S470 into the cx23885 driver.
This will be easy, except for filling out the v4l2_subdev_ir_parameters
in cx23885/cx23885-input.c:cx23885_input_ir_start() ; I will need
someone with hardware to experiment.

> In any case I can test.

Thank you.  I will probably need you for testing when ready.


I was planning to do step 1 above for HVR-1800 IR anyway.

I will estimate that I may have something ready by about Christmas (25
December 2009), unless work becomes very busy.

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Matthias Fechner]

Hi Andy,

Andy Walls wrote:
> Thank you.  I will probably need you for testing when ready.
>
>
> I was planning to do step 1 above for HVR-1800 IR anyway.
>
> I will estimate that I may have something ready by about Christmas (25
> December 2009), unless work becomes very busy.
>   

thanks a lot for your answer.
I uploaded two pictures I did from the card, you can find it here:
http://fechner.net/tevii-s470/

It is a CX23885.
The driver I use is the ds3000.
lspci says:
02:00.0 Multimedia video controller: Conexant Device 8852 (rev 02)
    Subsystem: Device d470:9022
    Flags: bus master, fast devsel, latency 0, IRQ 19
    Memory at fac00000 (64-bit, non-prefetchable) [size=2M]
    Capabilities: [40] Express Endpoint, MSI 00
    Capabilities: [80] Power Management version 2
    Capabilities: [90] Vital Product Data <?>
    Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ 
Count=1/1 Enable-
    Capabilities: [100] Advanced Error Reporting
        UESta:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF- MalfTLP- ECRC- UnsupReq+ ACSVoil-
        UEMsk:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil-
        UESvrt:    DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSVoil-
        CESta:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
        CESta:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
        AERCap:    First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
    Capabilities: [200] Virtual Channel <?>
    Kernel driver in use: cx23885
    Kernel modules: cx23885

lsmod says:
Module                  Size  Used by
lirc_serial            10740  1
snd_mixer_oss          12428  0
lirc_dev                9512  3 lirc_serial
snd_hda_codec_nvhdmi     3976  1
ds3000                 12820  1
snd_hda_codec_realtek   184292  1
cx23885               105116  9
cx2341x                10784  1 cx23885
v4l2_common            15428  2 cx23885,cx2341x
nvidia               8860344  44
videodev               34080  2 cx23885,v4l2_common
v4l1_compat            11252  1 videodev
videobuf_dma_sg        11176  1 cx23885
videobuf_dvb            6308  1 cx23885
dvb_core               78492  2 cx23885,videobuf_dvb
videobuf_core          16280  3 cx23885,videobuf_dma_sg,videobuf_dvb
snd_hda_intel          22004  1
ir_common              46132  1 cx23885
snd_hda_codec          55908  3 
snd_hda_codec_nvhdmi,snd_hda_codec_realtek,snd_hda_intel
btcx_risc               4244  1 cx23885
tveeprom               10652  1 cx23885
snd_pcm                63812  3 snd_hda_intel,snd_hda_codec
snd_timer              17584  1 snd_pcm
ehci_hcd               29628  0
ohci_hcd               19664  0
snd                    49728  7 
snd_mixer_oss,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer
usbcore               117380  2 ehci_hcd,ohci_hcd
i2c_nforce2             6092  0
serio_raw               4708  0
soundcore               6276  1 snd
i2c_core               19848  7 
ds3000,cx23885,v4l2_common,nvidia,videodev,tveeprom,i2c_nforce2
snd_page_alloc          7952  2 snd_hda_intel,snd_pcm
evdev                   8148  4


I can test any patch when you have one ready, currently I'm using lirc 
together with a TechnoTrend RemoteControl.
Thanks a lot and have a nice week

Best regards,
Matthias

-- 
"Programming today is a race between software engineers striving to build bigger and better idiot-proof programs, and the universe trying to produce bigger and better idiots. So far, the universe is winning." -- Rich Cook

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Sun, 2009-11-22 at 19:08 +0100, Matthias Fechner wrote:
> Hi Andy,
> 
> Andy Walls wrote:
> > Thank you.  I will probably need you for testing when ready.
> >
> >
> > I was planning to do step 1 above for HVR-1800 IR anyway.
> >
> > I will estimate that I may have something ready by about Christmas (25
> > December 2009), unless work becomes very busy.
> >   
> 
> thanks a lot for your answer.
> I uploaded two pictures I did from the card, you can find it here:
> http://fechner.net/tevii-s470/
> 
> It is a CX23885.
> The driver I use is the ds3000.
> lspci says:
[snip]

Matthias,

Thanks for the pictures.  OK so of the two other interesting chips on
the S470:

U4 is an I2C connected EEPROM - we don't care about that for IR.

U10 appears to perhaps be a Silicon Labs C8051F300 microcontroller or
similar:

http://www.silabs.com/products/mcu/smallmcu/Pages/C8051F30x.aspx

Since the 'F300 has an A/D convertor and has an SMBus interface
(compatable with the I2C bus), I suspect this chip could be the IR
controller on the TeVii S470.

Could you as root:

# modprobe cx23885
# modprobe i2c-dev
# i2c-detect -l
(to list all the i2c buses, including cx23885 mastered i2c buses)
# i2c-detect -y N
(to show the addresses in use on bus # N: only query the cx23885 buses)


i2c-detect was in the lm-sensors package last I checked.  (Jean can
correct me if I'm wrong.)

With that information, I should be able to figure out what I2C address
that microcontroller is listening to.

Then we can work out how to read and decode it's data and add it to
ir-kbd-i2c at least.  Depending on how your kernel and LIRC versions
LIRC might still work with I2C IR chips too.


All presupposing of course that that 'F300 chip is for IR...

Regards,
Andy

> I can test any patch when you have one ready, currently I'm using lirc 
> together with a TechnoTrend RemoteControl.
> Thanks a lot and have a nice week
> 
> Best regards,
> Matthias

Re: IR Receiver on an Tevii S470

[Matthias Fechner]

Hi Andy,

Andy Walls wrote:
>
> # modprobe cx23885
> # modprobe i2c-dev
> # i2c-detect -l
> (to list all the i2c buses, including cx23885 mastered i2c buses)
>   
i2c-0    smbus         SMBus nForce2 adapter at 4d00       SMBus adapter
i2c-1    i2c           cx23885[0]                          I2C adapter
i2c-2    i2c           cx23885[0]                          I2C adapter
i2c-3    i2c           cx23885[0]                          I2C adapter
i2c-4    i2c           NVIDIA i2c adapter                  I2C adapter
i2c-5    i2c           NVIDIA i2c adapter                  I2C adapter
i2c-6    i2c           NVIDIA i2c adapter                  I2C adapter

> # i2c-detect -y N
> (to show the addresses in use on bus # N: only query the cx23885 buses)
>
>   
vdrhd1 ~ # i2cdetect -y 1
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --                        
vdrhd1 ~ # i2cdetect -y 2
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
60: -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --                        
vdrhd1 ~ # i2cdetect -y 3
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
40: -- -- -- -- 44 -- -- -- -- -- -- -- 4c -- -- --
50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --                        

> i2c-detect was in the lm-sensors package last I checked.  (Jean can
> correct me if I'm wrong.)
>
>   
ok, it seems that the name of tool is different here, but I think it has 
the same output.

> Then we can work out how to read and decode it's data and add it to
> ir-kbd-i2c at least.  Depending on how your kernel and LIRC versions
> LIRC might still work with I2C IR chips too.
>
>   
I will do my best to help you here.

Bye,
Matthias

-- 
"Programming today is a race between software engineers striving to build bigger and better idiot-proof programs, and the universe trying to produce bigger and better idiots. So far, the universe is winning." -- Rich Cook

Re: IR Receiver on an Tevii S470

[Jean Delvare]

Hi Andy,

On Sun, 22 Nov 2009 15:11:47 -0500, Andy Walls wrote:
> On Sun, 2009-11-22 at 19:08 +0100, Matthias Fechner wrote:
> > thanks a lot for your answer.
> > I uploaded two pictures I did from the card, you can find it here:
> > http://fechner.net/tevii-s470/
> > 
> > It is a CX23885.
> > The driver I use is the ds3000.
> > lspci says:
> [snip]
> 
> Thanks for the pictures.  OK so of the two other interesting chips on
> the S470:
> 
> U4 is an I2C connected EEPROM - we don't care about that for IR.
> 
> U10 appears to perhaps be a Silicon Labs C8051F300 microcontroller or
> similar:
> 
> http://www.silabs.com/products/mcu/smallmcu/Pages/C8051F30x.aspx
> 
> Since the 'F300 has an A/D convertor and has an SMBus interface
> (compatable with the I2C bus), I suspect this chip could be the IR
> controller on the TeVii S470.
> 
> Could you as root:
> 
> # modprobe cx23885
> # modprobe i2c-dev
> # i2c-detect -l
> (to list all the i2c buses, including cx23885 mastered i2c buses)
> # i2c-detect -y N
> (to show the addresses in use on bus # N: only query the cx23885 buses)
> 
> 
> i2c-detect was in the lm-sensors package last I checked.  (Jean can
> correct me if I'm wrong.)

It is actually named "i2cdetect" (no dash). It used to live in the
lm-sensors package (up to 2.10.x) but is now in i2c-tools:

http://www.lm-sensors.org/wiki/I2CTools

> With that information, I should be able to figure out what I2C address
> that microcontroller is listening to.

-- 
Jean Delvare

Re: IR Receiver on an Tevii S470

[Jean Delvare]

On Sun, 22 Nov 2009 21:25:27 +0100, Matthias Fechner wrote:
> Hi Andy,
> 
> Andy Walls wrote:
> >
> > # modprobe cx23885
> > # modprobe i2c-dev
> > # i2c-detect -l
> > (to list all the i2c buses, including cx23885 mastered i2c buses)
> >   
> i2c-0    smbus         SMBus nForce2 adapter at 4d00       SMBus adapter
> i2c-1    i2c           cx23885[0]                          I2C adapter
> i2c-2    i2c           cx23885[0]                          I2C adapter
> i2c-3    i2c           cx23885[0]                          I2C adapter
> i2c-4    i2c           NVIDIA i2c adapter                  I2C adapter
> i2c-5    i2c           NVIDIA i2c adapter                  I2C adapter
> i2c-6    i2c           NVIDIA i2c adapter                  I2C adapter
> 
> > # i2c-detect -y N
> > (to show the addresses in use on bus # N: only query the cx23885 buses)
> >
> >   
> vdrhd1 ~ # i2cdetect -y 1
>      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
> 00:          -- -- -- -- -- -- -- -- -- -- -- -- --
> 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
> 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
> 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 70: -- -- -- -- -- -- -- --                        
> vdrhd1 ~ # i2cdetect -y 2
>      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
> 00:          -- -- -- -- -- -- -- -- -- -- -- -- --
> 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
> 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
> 60: -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- --
> 70: -- -- -- -- -- -- -- --                        
> vdrhd1 ~ # i2cdetect -y 3
>      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
> 00:          -- -- -- -- -- -- -- -- -- -- -- -- --
> 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
> 40: -- -- -- -- 44 -- -- -- -- -- -- -- 4c -- -- --
> 50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
> 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 70: -- -- -- -- -- -- -- --                        

The fact that 0x30-0x37 and 0x50-0x5f all reply suggest that the bus
driver erroneously returns success to "SMBus receive byte" transactions
even when no device acks. This is a bug which should get fixed. If you
point me to the I2C adapter driver code, I can take a look.

In the meantime, you can try i2cdetect -q to force i2cdetect to use
"SMBus quick" commands for all the addresses. Beware though that some
chips are known to not like it at all (in particular the infamous
AT24RF08... not that I expect to ever see one on a TV adapter but you
never know.)

At least the above scan has already found 3 chips.

-- 
Jean Delvare

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 22 ноября 2009 22:11:47 Andy Walls wrote:
> On Sun, 2009-11-22 at 19:08 +0100, Matthias Fechner wrote:
> > Hi Andy,
> >
> > Andy Walls wrote:
> > > Thank you.  I will probably need you for testing when ready.
> > >
> > >
> > > I was planning to do step 1 above for HVR-1800 IR anyway.
> > >
> > > I will estimate that I may have something ready by about Christmas (25
> > > December 2009), unless work becomes very busy.
> >
> > thanks a lot for your answer.
> > I uploaded two pictures I did from the card, you can find it here:
> > http://fechner.net/tevii-s470/
> >
> > It is a CX23885.
> > The driver I use is the ds3000.
> > lspci says:
>
> [snip]
>
> Matthias,
>
> Thanks for the pictures.  OK so of the two other interesting chips on
> the S470:
>
> U4 is an I2C connected EEPROM - we don't care about that for IR.
>
> U10 appears to perhaps be a Silicon Labs C8051F300 microcontroller or
> similar:
>
> http://www.silabs.com/products/mcu/smallmcu/Pages/C8051F30x.aspx
>
> Since the 'F300 has an A/D convertor and has an SMBus interface
> (compatable with the I2C bus), I suspect this chip could be the IR
> controller on the TeVii S470.
>
> Could you as root:
>
> # modprobe cx23885
> # modprobe i2c-dev
> # i2c-detect -l
> (to list all the i2c buses, including cx23885 mastered i2c buses)
> # i2c-detect -y N
> (to show the addresses in use on bus # N: only query the cx23885 buses)
>
>
> i2c-detect was in the lm-sensors package last I checked.  (Jean can
> correct me if I'm wrong.)
>
> With that information, I should be able to figure out what I2C address
> that microcontroller is listening to.
>
> Then we can work out how to read and decode it's data and add it to
> ir-kbd-i2c at least.  Depending on how your kernel and LIRC versions
> LIRC might still work with I2C IR chips too.
>
>
> All presupposing of course that that 'F300 chip is for IR...
Receiver connected to cx23885 IR_RX(pin 106). It is not difficult to track.

F300 is for LNB power control.
It connected to cx23885 GPIO pins:
GPIO0 - data - P0.3 F300
GPIO1 - reset - P0.2 F300
GPIO2 - clk - P0.1 F300
GPIO3 - busy - P0.0 F300

Interface seems not I2C/SMBUS.
 
Source code from TeVii:
http://mercurial.intuxication.org/hg/s2-
liplianin/file/d0dfe416e0f6/linux/drivers/media/video/cx23885/tevii_pwr.c

BR
Igor
>
> Regards,
> Andy
>
> > I can test any patch when you have one ready, currently I'm using lirc
> > together with a TechnoTrend RemoteControl.
> > Thanks a lot and have a nice week
> >
> > Best regards,
> > Matthias

-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Mon, 2009-11-23 at 00:29 +0200, Igor M. Liplianin wrote:
> On 22 ноября 2009 22:11:47 Andy Walls wrote:
> > On Sun, 2009-11-22 at 19:08 +0100, Matthias Fechner wrote:
> > > Hi Andy,
> > >
> > > Andy Walls wrote:
> > > > Thank you.  I will probably need you for testing when ready.
> > > >
> > > >
> > > > I was planning to do step 1 above for HVR-1800 IR anyway.
> > > >
> > > > I will estimate that I may have something ready by about Christmas (25
> > > > December 2009), unless work becomes very busy.
> > >
> > > thanks a lot for your answer.
> > > I uploaded two pictures I did from the card, you can find it here:
> > > http://fechner.net/tevii-s470/
> > >
> > > It is a CX23885.
> > > The driver I use is the ds3000.
> > > lspci says:
> >
> > [snip]
> >
> > Matthias,
> >
> > Thanks for the pictures.  OK so of the two other interesting chips on
> > the S470:
> >
> > U4 is an I2C connected EEPROM - we don't care about that for IR.
> >
> > U10 appears to perhaps be a Silicon Labs C8051F300 microcontroller or
> > similar:
> >
> > http://www.silabs.com/products/mcu/smallmcu/Pages/C8051F30x.aspx
> >
> > Since the 'F300 has an A/D convertor and has an SMBus interface
> > (compatable with the I2C bus), I suspect this chip could be the IR
> > controller on the TeVii S470.
> >
> > Could you as root:
> >
> > # modprobe cx23885
> > # modprobe i2c-dev
> > # i2c-detect -l
> > (to list all the i2c buses, including cx23885 mastered i2c buses)
> > # i2c-detect -y N
> > (to show the addresses in use on bus # N: only query the cx23885 buses)
> >
> >
> > i2c-detect was in the lm-sensors package last I checked.  (Jean can
> > correct me if I'm wrong.)
> >
> > With that information, I should be able to figure out what I2C address
> > that microcontroller is listening to.
> >
> > Then we can work out how to read and decode it's data and add it to
> > ir-kbd-i2c at least.  Depending on how your kernel and LIRC versions
> > LIRC might still work with I2C IR chips too.
> >
> >
> > All presupposing of course that that 'F300 chip is for IR...
> Receiver connected to cx23885 IR_RX(pin 106). It is not difficult to track.

Igor,

Thank you.  I did not have a board to trace.  I will then stick with my
original plan since the F300 doesn't do the IR.

> F300 is for LNB power control.
> It connected to cx23885 GPIO pins:
> GPIO0 - data - P0.3 F300
> GPIO1 - reset - P0.2 F300
> GPIO2 - clk - P0.1 F300
> GPIO3 - busy - P0.0 F300
> 
> Interface seems not I2C/SMBUS.
>  
> Source code from TeVii:
> http://mercurial.intuxication.org/hg/s2-
> liplianin/file/d0dfe416e0f6/linux/drivers/media/video/cx23885/tevii_pwr.c

Interesting....

   static void Delay1mS(void)
   {
	   udelay(800);
   }

:D

Regards,
Andy

> BR
> Igor

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 23 ноября 2009, "Igor M. Liplianin" <liplianin@me.by> wrote:
> On Mon, 2009-11-23 at 00:29 +0200, Igor M. Liplianin wrote:
> > On 22 ноября 2009 22:11:47 Andy Walls wrote:
> > > On Sun, 2009-11-22 at 19:08 +0100, Matthias Fechner wrote:
> > > > Hi Andy,
> > > >
> > > > Andy Walls wrote:
> > > > > Thank you.  I will probably need you for testing when ready.
> > > > >
> > > > >
> > > > > I was planning to do step 1 above for HVR-1800 IR anyway.
> > > > >
> > > > > I will estimate that I may have something ready by about Christmas
> > > > > (25 December 2009), unless work becomes very busy.
> > > >
> > > > thanks a lot for your answer.
> > > > I uploaded two pictures I did from the card, you can find it here:
> > > > http://fechner.net/tevii-s470/
> > > >
> > > > It is a CX23885.
> > > > The driver I use is the ds3000.
> > > > lspci says:
> > >
> > > [snip]
> > >
> > > Matthias,
> > >
> > > Thanks for the pictures.  OK so of the two other interesting chips on
> > > the S470:
> > >
> > > U4 is an I2C connected EEPROM - we don't care about that for IR.
> > >
> > > U10 appears to perhaps be a Silicon Labs C8051F300 microcontroller or
> > > similar:
> > >
> > > http://www.silabs.com/products/mcu/smallmcu/Pages/C8051F30x.aspx
> > >
> > > Since the 'F300 has an A/D convertor and has an SMBus interface
> > > (compatable with the I2C bus), I suspect this chip could be the IR
> > > controller on the TeVii S470.
> > >
> > > Could you as root:
> > >
> > > # modprobe cx23885
> > > # modprobe i2c-dev
> > > # i2c-detect -l
> > > (to list all the i2c buses, including cx23885 mastered i2c buses)
> > > # i2c-detect -y N
> > > (to show the addresses in use on bus # N: only query the cx23885 buses)
> > >
> > >
> > > i2c-detect was in the lm-sensors package last I checked.  (Jean can
> > > correct me if I'm wrong.)
> > >
> > > With that information, I should be able to figure out what I2C address
> > > that microcontroller is listening to.
> > >
> > > Then we can work out how to read and decode it's data and add it to
> > > ir-kbd-i2c at least.  Depending on how your kernel and LIRC versions
> > > LIRC might still work with I2C IR chips too.
> > >
> > >
> > > All presupposing of course that that 'F300 chip is for IR...
> >
> > Receiver connected to cx23885 IR_RX(pin 106). It is not difficult to
> > track.
>
> Igor,
>
> Thank you.  I did not have a board to trace.  I will then stick with my
> original plan since the F300 doesn't do the IR.
I have cx23885 based Compro E650F DVB-T card. It shipped with RC6 type remote.
So I can test RC6 too... And I will.

>
> > F300 is for LNB power control.
> > It connected to cx23885 GPIO pins:
> > GPIO0 - data - P0.3 F300
> > GPIO1 - reset - P0.2 F300
> > GPIO2 - clk - P0.1 F300
> > GPIO3 - busy - P0.0 F300
> >
> > Interface seems not I2C/SMBUS.
> >
> > Source code from TeVii:
> > http://mercurial.intuxication.org/hg/s2-
> > liplianin/file/d0dfe416e0f6/linux/drivers/media/video/cx23885/tevii_pwr.c
>
> Interesting....
>
>    static void Delay1mS(void)
>    {
> 	   udelay(800);
>    }
>
> :D
Your link to datasheet helps me a lot :)
I will clear all that out and will commit to linuxtv soon.

BR
Igor
>
> Regards,
> Andy
>
> > BR
> > Igor
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html


-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Sun, 2009-11-22 at 21:32 +0100, Jean Delvare wrote:
> On Sun, 22 Nov 2009 21:25:27 +0100, Matthias Fechner wrote:
> > Hi Andy,
> > 
> > Andy Walls wrote:
> > >
> > > # modprobe cx23885
> > > # modprobe i2c-dev
> > > # i2c-detect -l
> > > (to list all the i2c buses, including cx23885 mastered i2c buses)
> > >   
> > i2c-0    smbus         SMBus nForce2 adapter at 4d00       SMBus adapter
> > i2c-1    i2c           cx23885[0]                          I2C adapter
> > i2c-2    i2c           cx23885[0]                          I2C adapter
> > i2c-3    i2c           cx23885[0]                          I2C adapter
> > i2c-4    i2c           NVIDIA i2c adapter                  I2C adapter
> > i2c-5    i2c           NVIDIA i2c adapter                  I2C adapter
> > i2c-6    i2c           NVIDIA i2c adapter                  I2C adapter
> > 
> > > # i2c-detect -y N
> > > (to show the addresses in use on bus # N: only query the cx23885 buses)
> > >
> > >   
> > vdrhd1 ~ # i2cdetect -y 1
> >      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
> > 00:          -- -- -- -- -- -- -- -- -- -- -- -- --
> > 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
> > 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
> > 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 70: -- -- -- -- -- -- -- --                        
> > vdrhd1 ~ # i2cdetect -y 2
> >      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
> > 00:          -- -- -- -- -- -- -- -- -- -- -- -- --
> > 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
> > 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
> > 60: -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- --
> > 70: -- -- -- -- -- -- -- --                        
> > vdrhd1 ~ # i2cdetect -y 3
> >      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
> > 00:          -- -- -- -- -- -- -- -- -- -- -- -- --
> > 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
> > 40: -- -- -- -- 44 -- -- -- -- -- -- -- 4c -- -- --
> > 50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
> > 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> > 70: -- -- -- -- -- -- -- --                        
> 
> The fact that 0x30-0x37 and 0x50-0x5f all reply suggest that the bus
> driver erroneously returns success to "SMBus receive byte" transactions
> even when no device acks. This is a bug which should get fixed. If you
> point me to the I2C adapter driver code, I can take a look.

Jean,

Although Igor's information makes the original need for this moot, here
is the i2c adapter driver code:

http://linuxtv.org/hg/v4l-dvb/file/8bff7e6c44d4/linux/drivers/media/video/cx23885/cx23885-i2c.c

Note the CX2388[578] chips have 3 I2C masters, 2 for external buses, and
1 internal "on silicon" bus which the driver sets up as the 3rd bus.
The internal bus should at least have devices at 0x44 and 0x4c as
confirmed above.  I'll note the comment in this file, that indicates the
"on silicon" I2C bus runs at 1.95 MHz:

http://linuxtv.org/hg/v4l-dvb/file/8bff7e6c44d4/linux/drivers/media/video/cx23885/cx23885-core.c


The TeVii S470 card had what looked like at serial I2C EEPROM with the
A0, A1, and A2 pins all grounded, so I assume it is at 0x50 on one of
the CX23885's external I2C buses.

Regards,
Andy


> In the meantime, you can try i2cdetect -q to force i2cdetect to use
> "SMBus quick" commands for all the addresses. Beware though that some
> chips are known to not like it at all (in particular the infamous
> AT24RF08... not that I expect to ever see one on a TV adapter but you
> never know.)
> 
> At least the above scan has already found 3 chips.
> 

Re: IR Receiver on an Tevii S470

[Jean Delvare]

On Sun, 22 Nov 2009 19:17:59 -0500, Andy Walls wrote:
> On Sun, 2009-11-22 at 21:32 +0100, Jean Delvare wrote:
> > The fact that 0x30-0x37 and 0x50-0x5f all reply suggest that the bus
> > driver erroneously returns success to "SMBus receive byte" transactions
> > even when no device acks. This is a bug which should get fixed. If you
> > point me to the I2C adapter driver code, I can take a look.
> 
> Although Igor's information makes the original need for this moot, here
> is the i2c adapter driver code:
> 
> http://linuxtv.org/hg/v4l-dvb/file/8bff7e6c44d4/linux/drivers/media/video/cx23885/cx23885-i2c.c

The results are not surprising: i2c_slave_did_ack() is only called for
zero-length transactions. For all other transactions, no check is done.
This is incorrect.

I have written 3 patches for cx23885-i2c.c, the second one should fix
this particular issue. The other two are cleanups. Patches are there if
you want to take a look / give them a try:
http://khali.linux-fr.org/devel/misc/cx23885/

These are totally untested, and I don't know anything about the
hardware, so they might need some more work. But at least you should
get the idea of what's missing.

> Note the CX2388[578] chips have 3 I2C masters, 2 for external buses, and
> 1 internal "on silicon" bus which the driver sets up as the 3rd bus.
> The internal bus should at least have devices at 0x44 and 0x4c as
> confirmed above.  I'll note the comment in this file, that indicates the
> "on silicon" I2C bus runs at 1.95 MHz:
> 
> http://linuxtv.org/hg/v4l-dvb/file/8bff7e6c44d4/linux/drivers/media/video/cx23885/cx23885-core.c

This is strange. For one thing, 1.95 MHz wouldn't be standard I2C but
high-speed mode I2C. But more importantly, I fail to see how you could
reach such speeds with a software-driven, byte-by-byte implementation.
You need hardware buffers to reach high speeds on I2C.

> The TeVii S470 card had what looked like at serial I2C EEPROM with the
> A0, A1, and A2 pins all grounded, so I assume it is at 0x50 on one of
> the CX23885's external I2C buses.

Probably. Hopefully my patches will show you where it is.

-- 
Jean Delvare

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Mon, 2009-11-23 at 09:54 +0100, Jean Delvare wrote:
> On Sun, 22 Nov 2009 19:17:59 -0500, Andy Walls wrote:
> > On Sun, 2009-11-22 at 21:32 +0100, Jean Delvare wrote:
> > > The fact that 0x30-0x37 and 0x50-0x5f all reply suggest that the bus
> > > driver erroneously returns success to "SMBus receive byte" transactions
> > > even when no device acks. This is a bug which should get fixed. If you
> > > point me to the I2C adapter driver code, I can take a look.
> > 
> > Although Igor's information makes the original need for this moot, here
> > is the i2c adapter driver code:
> > 
> > http://linuxtv.org/hg/v4l-dvb/file/8bff7e6c44d4/linux/drivers/media/video/cx23885/cx23885-i2c.c
> 
> The results are not surprising: i2c_slave_did_ack() is only called for
> zero-length transactions. For all other transactions, no check is done.
> This is incorrect.
> 
> I have written 3 patches for cx23885-i2c.c, the second one should fix
> this particular issue. The other two are cleanups. Patches are there if
> you want to take a look / give them a try:
> http://khali.linux-fr.org/devel/misc/cx23885/
> 
> These are totally untested, and I don't know anything about the
> hardware, so they might need some more work. But at least you should
> get the idea of what's missing.

Jean,

(adding Steven Toth to the Cc: list)

Thanks!

I will inspect and test these with my HVR-1850 (CX23888) loaner board
this weekend (hopefully).

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Matthias Fechner]

Hi Andy,

Andy Walls wrote:
> I will inspect and test these with my HVR-1850 (CX23888) loaner board
> this weekend (hopefully).
>   

if you want me to test something on the Tevii S470 card, please let me know.

Bye,
Matthias

-- 
"Programming today is a race between software engineers striving to build bigger and better idiot-proof programs, and the universe trying to produce bigger and better idiots. So far, the universe is winning." -- Rich Cook

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Thu, 2009-11-26 at 17:43 +0100, Matthias Fechner wrote:
> Hi Andy,
> 
> Andy Walls wrote:
> > I will inspect and test these with my HVR-1850 (CX23888) loaner board
> > this weekend (hopefully).
> >   
> 
> if you want me to test something on the Tevii S470 card, please let me know.

MAtthias,

Not right now.  I'll let you know.  If you wish, you can monitor

	http://linuxtv.org/hg/~awalls/cx23885-ir

Right now that repository has Jean's patches which I have minimally
tested.  They do fix the i2cdetect problems.

There are not TeVii S470 patches there, so I'm not sure how easy it will
be for you to test.

In the v4l2_subdev_ir_parameters and cx23888-ir.c, I need to improve a
minor point about carrier sense inversion (configuring if a carrier
burst means mark or space) and IO pin level inversion.  After that, I
can port cx23888-ir.c to a cx25840-ir.c implementation.

I also have to implement NEC decoding in cx23885-input.c.  I found a
remote in my house that implements the NEC protocol with Extended
addresses (although its timing is about 100 microseconds short for every
mark & space pair and the header pulse is almost 1 ms shorter than it
should be :P ).  I should be able to get NEC decoding worked out with
that remote and the HVR-1850 I have in hand.

Merging TeVii S470 fixes from Igor will then be a final step before I
ask you to correct my guess at the v4l2_subdev_ir_parameters setup in
cx23885-input.c for your card.


Regards,
Andy

> Bye,
> Matthias

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Sun, 2009-11-22 at 03:03 +0200, Igor M. Liplianin wrote:
> On 21 ноября 2009 22:41:42 Andy Walls wrote:
> > > Matthias Fechner schrieb:
> > > > I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got it
> > > > running with the driver from:
> > > > http://mercurial.intuxication.org/hg/s2-liplianin
> > > >
> > > > But I was not successfull in got the IR receiver working.
> > > > It seems that it is not supported yet by the driver.
> > > >
> > > > Is there maybe some code available to get the IR receiver with evdev
> > > > running?

> > If the card is using the built in IR controller in the CX23885, then
> > you'll have to wait until I port my CX23888 IR controller changes to
> > work with the IR controller in the CX23885.  That should be somewhat
> > straightforward, but will take time.  Then we'll still need you to
> > experiment with a patch.

> It's cx23885 definitely.
> Remote uses NEC codes.
> In any case I can test.


On Mon, 2009-11-23, Igor M. Liplianin wrote:
> Receiver connected to cx23885 IR_RX(pin 106). It is not difficult to
> track.


Igor,

As I make patches for test, perhaps you can help answer some questions
which will save some experimentation:


1. Does the remote for the TeVii S470 use the same codes as

linux/drivers/media/common/ir-keymaps.c : ir_codes_tevii_nec[]

or some other remote code table we have in the kernel?


2. Does the remote for the TeVii S470, like other TeVii remotes, use a
standard NEC address of 0x00 (so that Addr'Addr is 0xff00) ?  Or does it
use another address?


3. When you traced board wiring from the IR receiver to the IR_RX pin on
the CX23885, did you notice any external components that might modify
the signal?  For example, a capacitor that integrates carrier bursts
into baseband pulses.


Thanks.

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Matthias Fechner]

[-- Attachment #1: Type: text/plain, Size: 623 bytes --]

Hi Andy,

Andy Walls wrote:
>
> 1. Does the remote for the TeVii S470 use the same codes as
>
> linux/drivers/media/common/ir-keymaps.c : ir_codes_tevii_nec[]
>
> or some other remote code table we have in the kernel?
>   

I don't know how it should work with the kernel but I use the remote 
together with lirc with the attached config files.
Maybe that helps you a little bit.

Bye,
Matthias

-- 
"Programming today is a race between software engineers striving to build bigger and better idiot-proof programs, and the universe trying to produce bigger and better idiots. So far, the universe is winning." -- Rich Cook


[-- Attachment #2: lirc-tevii.conf --]
[-- Type: text/plain, Size: 2615 bytes --]

#
# this config file was automatically generated
# using lirc-0.8.4(default) on Sun Jul 12 12:05:06 2009
#
# contributed by
#
# brand:                      TeVii
# model no. of remote control:
# devices being controlled by this remote: TeVii S650 DVB-S2 USB
#

begin remote

  name  TeVii_S470
  bits           16
  flags SPACE_ENC|CONST_LENGTH
  eps            30
  aeps          100

  header       9032  4440
  one           594  1651
  zero          594   527
  ptrail        592
  repeat	9032	2212
  pre_data_bits   16
  pre_data       0xFF
  gap          107715
  toggle_bit_mask 0x8000

     begin codes
          Power                    0x50AF
          Mute                     0x30CF
          1                        0x8877
          2                        0x48B7
          3                        0xC837
          4                        0x28D7
          5                        0xA857
          6                        0x6897
          7                        0xE817
          8                        0x18E7
          9                        0x9867
          0                        0x08F7
          recall                   0x58A7
          fav                      0xD827
          Vol+                     0x906F
          Vol-                     0xF00F
          Chan+                    0x10EF
          Chan-                    0x609F
          ModeLive                 0xA05F
          ModePlay                 0xE01F
          Up                       0x00FF
          Down                     0x807F
          Left                     0xC03F
          Right                    0x40BF
          Ok                       0xF807
          Menu                     0x38C7
          Back                     0xB847
          Play                     0x02FD
          FastRew                  0x7887
          FastFwd                  0xB24D
          EPG                      0x22DD
          Rec                      0x20DF
          Timer                    0xD02F
          Open                     0x708F
          Info                     0x32CD
          a/b                       0x827D
          Audio                    0xC23D
          subs                     0xA25D
          List                     0x52AD
          F1                       0x629D
          F2                       0xE21D
          F3                       0x7A85
          F4                       0x3AC5
          F5                       0x4AB5
          F6                       0x5AA5
          mom                      0x6A95
          fs                       0x1AE5
      end codes

end remote

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 6 декабря 2009 23:40:54 Andy Walls wrote:
> On Sun, 2009-11-22 at 03:03 +0200, Igor M. Liplianin wrote:
> > On 21 ноября 2009 22:41:42 Andy Walls wrote:
> > > > Matthias Fechner schrieb:
> > > > > I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got it
> > > > > running with the driver from:
> > > > > http://mercurial.intuxication.org/hg/s2-liplianin
> > > > >
> > > > > But I was not successfull in got the IR receiver working.
> > > > > It seems that it is not supported yet by the driver.
> > > > >
> > > > > Is there maybe some code available to get the IR receiver with
> > > > > evdev running?
> > >
> > > If the card is using the built in IR controller in the CX23885, then
> > > you'll have to wait until I port my CX23888 IR controller changes to
> > > work with the IR controller in the CX23885.  That should be somewhat
> > > straightforward, but will take time.  Then we'll still need you to
> > > experiment with a patch.
> >
> > It's cx23885 definitely.
> > Remote uses NEC codes.
> > In any case I can test.
>
> On Mon, 2009-11-23, Igor M. Liplianin wrote:
> > Receiver connected to cx23885 IR_RX(pin 106). It is not difficult to
> > track.
>
> Igor,
Hi Andy,

>
> As I make patches for test, perhaps you can help answer some questions
> which will save some experimentation:
>
>
> 1. Does the remote for the TeVii S470 use the same codes as
>
> linux/drivers/media/common/ir-keymaps.c : ir_codes_tevii_nec[]
That is correct table for cx88 based TeVii card with the same remote.
I believe there is no difference for cx23885.

>
> or some other remote code table we have in the kernel?
>
>
> 2. Does the remote for the TeVii S470, like other TeVii remotes, use a
> standard NEC address of 0x00 (so that Addr'Addr is 0xff00) ?  Or does it
> use another address?
Again like in cx88, the address is standard.

>
>
> 3. When you traced board wiring from the IR receiver to the IR_RX pin on
> the CX23885, did you notice any external components that might modify
> the signal?  For example, a capacitor that integrates carrier bursts
> into baseband pulses.
Yet again I believe there is no capacitors.
Very same scheme like in cx88 variants for TeVii and others.

>
>
> Thanks.
>
> Regards,
> Andy

-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Mon, 2009-12-07 at 03:23 +0200, Igor M. Liplianin wrote:
> On 6 декабря 2009 23:40:54 Andy Walls wrote:
> > On Sun, 2009-11-22 at 03:03 +0200, Igor M. Liplianin wrote:
> > > On 21 ноября 2009 22:41:42 Andy Walls wrote:
> > > > > Matthias Fechner schrieb:
> > > > > > I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got it
> > > > > > running with the driver from:
> > > > > > http://mercurial.intuxication.org/hg/s2-liplianin
> > > > > >
> > > > > > But I was not successfull in got the IR receiver working.
> > > > > > It seems that it is not supported yet by the driver.
> > > > > >
> > > > > > Is there maybe some code available to get the IR receiver with
> > > > > > evdev running?
> > > >
> > > > If the card is using the built in IR controller in the CX23885, then
> > > > you'll have to wait until I port my CX23888 IR controller changes to
> > > > work with the IR controller in the CX23885.  That should be somewhat
> > > > straightforward, but will take time.  Then we'll still need you to
> > > > experiment with a patch.
> > >
> > > It's cx23885 definitely.
> > > Remote uses NEC codes.
> > > In any case I can test.
> >
> > On Mon, 2009-11-23, Igor M. Liplianin wrote:
> > > Receiver connected to cx23885 IR_RX(pin 106). It is not difficult to
> > > track.
> >
> > Igor,
> Hi Andy,
> 
> >
> > As I make patches for test, perhaps you can help answer some questions
> > which will save some experimentation:
> >
> >
> > 1. Does the remote for the TeVii S470 use the same codes as
> >
> > linux/drivers/media/common/ir-keymaps.c : ir_codes_tevii_nec[]
> That is correct table for cx88 based TeVii card with the same remote.
> I believe there is no difference for cx23885.
> 
> >
> > or some other remote code table we have in the kernel?
> >
> >
> > 2. Does the remote for the TeVii S470, like other TeVii remotes, use a
> > standard NEC address of 0x00 (so that Addr'Addr is 0xff00) ?  Or does it
> > use another address?
> Again like in cx88, the address is standard.
> 
> >
> >
> > 3. When you traced board wiring from the IR receiver to the IR_RX pin on
> > the CX23885, did you notice any external components that might modify
> > the signal?  For example, a capacitor that integrates carrier bursts
> > into baseband pulses.
> Yet again I believe there is no capacitors.
> Very same scheme like in cx88 variants for TeVii and others.


Igor and Matthias,

Please try the changes that I have for the TeVii S470 that are here:

	http://linuxtv.org/hg/~awalls/cx23885-ir

You will want to modprobe the driver modules like this to get debugging
information:

	# modprobe cx25840 ir_debug=2
	# modprobe cx23885 ir_input_debug=1

With that debugging you will get output something like this in dmesg or
your logs when you press a button on the remote (this is RC-5 using a
CX23888 chip not NEC using a CX23885 chip):

cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
cx23885[0]/888-ir: IRQ Enables:     rse rte roe
cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
cx23885[0]/888-ir: IRQ Enables:     rse rte roe
cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
cx23885[0]/888-ir: IRQ Enables:     rse rte roe
cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
cx23885[0]/888-ir: IRQ Enables:     rse rte roe
cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
cx23885[0]/888-ir: IRQ Enables:     rse rte roe
cx23885[0]/888-ir: IRQ Status:  tsr     rto            
cx23885[0]/888-ir: IRQ Enables:     rse rte roe
cx23885[0]/888-ir: rx read:     817000 ns  mark
cx23885[0]/888-ir: rx read:     838926 ns  space
cx23885[0]/888-ir: rx read:    1572259 ns  mark
cx23885[0]/888-ir: rx read:    1705296 ns  space
[...]
cx23885[0]/888-ir: rx read:     838037 ns  space
cx23885[0]/888-ir: rx read:     746333 ns  mark
cx23885[0]/888-ir: rx read:    1705741 ns  space
cx23885[0]/888-ir: rx read:    1619370 ns  mark
cx23885[0]/888-ir: rx read: end of rx

NEC would actually have this sort of timing:

8257296 ns  mark
4206185 ns  space
 482926 ns  mark
 545296 ns  space
 481296 ns  mark
1572259 ns  space
 481148 ns  mark
 546333 ns  space
[...]
 433593 ns  mark
1618333 ns  space
 454481 ns  mark
end of rx

8255519 ns  mark
2130926 ns  space
 480556 ns  mark
end of rx


The NEC decoder will also log the decoded 32 bits it receives and
separate out the address and the command bits.


If you do not see good or many NEC timing measurments in the logs, the
first thing to try is to change lines 533-534 of
linux/drivers/media/cx23885/cx23885-input.c:

               params.modulation = true;
               params.invert_level = false;

If you see no timing measurements or few timing measurements, change the
"modulation" to "false".  If the chip is expecting carrier pulses and an
external circuit or capacitor is smoothing carrier bursts into baseband
pulses, then the hardware won't make measurements properly.

If you see inverted mark and space inverted when "modulation" is set to
"false", then set "invert_level" to "true".

Those are the two things I had to really guess at.


BTW, I'm not accessing the CX23885 AV Core registers across the I2C bus
in a very conservative way.  If you notice some performance problem with
an occasionally missed pulse measurement, then I know there is room for
improvement by being smarter about I2C bus transactions.

Good Luck.

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 7 декабря 2009 05:35:46 Andy Walls wrote:
> On Mon, 2009-12-07 at 03:23 +0200, Igor M. Liplianin wrote:
> > On 6 декабря 2009 23:40:54 Andy Walls wrote:
> > > On Sun, 2009-11-22 at 03:03 +0200, Igor M. Liplianin wrote:
> > > > On 21 ноября 2009 22:41:42 Andy Walls wrote:
> > > > > > Matthias Fechner schrieb:
> > > > > > > I bought some days ago a Tevii S470 DVB-S2 (PCI-E) card and got
> > > > > > > it running with the driver from:
> > > > > > > http://mercurial.intuxication.org/hg/s2-liplianin
> > > > > > >
> > > > > > > But I was not successfull in got the IR receiver working.
> > > > > > > It seems that it is not supported yet by the driver.
> > > > > > >
> > > > > > > Is there maybe some code available to get the IR receiver with
> > > > > > > evdev running?
> > > > >
> > > > > If the card is using the built in IR controller in the CX23885,
> > > > > then you'll have to wait until I port my CX23888 IR controller
> > > > > changes to work with the IR controller in the CX23885.  That should
> > > > > be somewhat straightforward, but will take time.  Then we'll still
> > > > > need you to experiment with a patch.
> > > >
> > > > It's cx23885 definitely.
> > > > Remote uses NEC codes.
> > > > In any case I can test.
> > >
> > > On Mon, 2009-11-23, Igor M. Liplianin wrote:
> > > > Receiver connected to cx23885 IR_RX(pin 106). It is not difficult to
> > > > track.
> > >
> > > Igor,
> >
> > Hi Andy,
> >
> > > As I make patches for test, perhaps you can help answer some questions
> > > which will save some experimentation:
> > >
> > >
> > > 1. Does the remote for the TeVii S470 use the same codes as
> > >
> > > linux/drivers/media/common/ir-keymaps.c : ir_codes_tevii_nec[]
> >
> > That is correct table for cx88 based TeVii card with the same remote.
> > I believe there is no difference for cx23885.
> >
> > > or some other remote code table we have in the kernel?
> > >
> > >
> > > 2. Does the remote for the TeVii S470, like other TeVii remotes, use a
> > > standard NEC address of 0x00 (so that Addr'Addr is 0xff00) ?  Or does
> > > it use another address?
> >
> > Again like in cx88, the address is standard.
> >
> > > 3. When you traced board wiring from the IR receiver to the IR_RX pin
> > > on the CX23885, did you notice any external components that might
> > > modify the signal?  For example, a capacitor that integrates carrier
> > > bursts into baseband pulses.
> >
> > Yet again I believe there is no capacitors.
> > Very same scheme like in cx88 variants for TeVii and others.
>
> Igor and Matthias,
>
> Please try the changes that I have for the TeVii S470 that are here:
>
> 	http://linuxtv.org/hg/~awalls/cx23885-ir
>
> You will want to modprobe the driver modules like this to get debugging
> information:
>
> 	# modprobe cx25840 ir_debug=2
> 	# modprobe cx23885 ir_input_debug=1
>
> With that debugging you will get output something like this in dmesg or
> your logs when you press a button on the remote (this is RC-5 using a
> CX23888 chip not NEC using a CX23885 chip):
>
> cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> cx23885[0]/888-ir: IRQ Status:  tsr     rto
> cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> cx23885[0]/888-ir: rx read:     817000 ns  mark
> cx23885[0]/888-ir: rx read:     838926 ns  space
> cx23885[0]/888-ir: rx read:    1572259 ns  mark
> cx23885[0]/888-ir: rx read:    1705296 ns  space
> [...]
> cx23885[0]/888-ir: rx read:     838037 ns  space
> cx23885[0]/888-ir: rx read:     746333 ns  mark
> cx23885[0]/888-ir: rx read:    1705741 ns  space
> cx23885[0]/888-ir: rx read:    1619370 ns  mark
> cx23885[0]/888-ir: rx read: end of rx
>
> NEC would actually have this sort of timing:
>
> 8257296 ns  mark
> 4206185 ns  space
>  482926 ns  mark
>  545296 ns  space
>  481296 ns  mark
> 1572259 ns  space
>  481148 ns  mark
>  546333 ns  space
> [...]
>  433593 ns  mark
> 1618333 ns  space
>  454481 ns  mark
> end of rx
>
> 8255519 ns  mark
> 2130926 ns  space
>  480556 ns  mark
> end of rx
>
>
> The NEC decoder will also log the decoded 32 bits it receives and
> separate out the address and the command bits.
>
>
> If you do not see good or many NEC timing measurments in the logs, the
> first thing to try is to change lines 533-534 of
> linux/drivers/media/cx23885/cx23885-input.c:
>
>                params.modulation = true;
>                params.invert_level = false;
>
> If you see no timing measurements or few timing measurements, change the
> "modulation" to "false".  If the chip is expecting carrier pulses and an
> external circuit or capacitor is smoothing carrier bursts into baseband
> pulses, then the hardware won't make measurements properly.
>
> If you see inverted mark and space inverted when "modulation" is set to
> "false", then set "invert_level" to "true".
>
> Those are the two things I had to really guess at.
>
>
> BTW, I'm not accessing the CX23885 AV Core registers across the I2C bus
> in a very conservative way.  If you notice some performance problem with
> an occasionally missed pulse measurement, then I know there is room for
> improvement by being smarter about I2C bus transactions.
>
> Good Luck.
>
> Regards,
> Andy

No luck :(
Nothing in logs

-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Tue, 2009-12-08 at 19:59 +0200, Igor M. Liplianin wrote:
> On 7 декабря 2009 05:35:46 Andy Walls wrote:

> > Igor and Matthias,
> >
> > Please try the changes that I have for the TeVii S470 that are here:
> >
> > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> >
> > You will want to modprobe the driver modules like this to get debugging
> > information:
> >
> > 	# modprobe cx25840 ir_debug=2
> > 	# modprobe cx23885 ir_input_debug=1
> >
> > With that debugging you will get output something like this in dmesg or
> > your logs when you press a button on the remote (this is RC-5 using a
> > CX23888 chip not NEC using a CX23885 chip):
> >
> > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > cx23885[0]/888-ir: IRQ Status:  tsr     rto
> > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > cx23885[0]/888-ir: rx read:     817000 ns  mark
> > cx23885[0]/888-ir: rx read:     838926 ns  space
> > cx23885[0]/888-ir: rx read:    1572259 ns  mark
> > cx23885[0]/888-ir: rx read:    1705296 ns  space
> > [...]
> > cx23885[0]/888-ir: rx read:     838037 ns  space
> > cx23885[0]/888-ir: rx read:     746333 ns  mark
> > cx23885[0]/888-ir: rx read:    1705741 ns  space
> > cx23885[0]/888-ir: rx read:    1619370 ns  mark
> > cx23885[0]/888-ir: rx read: end of rx

> > If you do not see good or many NEC timing measurments in the logs, the
> > first thing to try is to change lines 533-534 of
> > linux/drivers/media/cx23885/cx23885-input.c:
> >
> >                params.modulation = true;
> >                params.invert_level = false;
> >
> > If you see no timing measurements or few timing measurements, change the
> > "modulation" to "false".  If the chip is expecting carrier pulses and an
> > external circuit or capacitor is smoothing carrier bursts into baseband
> > pulses, then the hardware won't make measurements properly.
> >
> > If you see inverted mark and space inverted when "modulation" is set to
> > "false", then set "invert_level" to "true".
> >
> > Those are the two things I had to really guess at.

> > Regards,
> > Andy
> 
> No luck :(
> Nothing in logs

:(

OK.

1. I assume you have the v4l-cx23885-avcore-01.fw file available for the
cx25840 module, just so there is no problem initializing the CX23885 AV
core.


2. Does dmesg or the logs show the input device being created?
Somewhere in the log you should see:

	"cx23885 IR (TeVii S470)"

when the input device is created.


3. With the "debug=7" option to the cx23885 module, do you see any IR
interrupts coming in?  In dmesg or the log you should see:

	"(PCI_MSK_IR        0x...)"

when an IR interrupt happens.


Tonight I will:

a. Add a guess at HVR-1800 support so maybe Steve can help us debug as
well.  I know the NEC decoder works; I tested it.  What I don't know is
if the CX23885 AV IR implementation works (I don't have CX23885 hardware
at the moment).

b. Add a temporary patch to add a /dev/videoN node for the TeVii S470 so
you can use "v4l2-ctl --log-status" to show the status of the IR
controller and v4l2-dbg to dump the cx23885 and cx23885-av-core
registers, so I can see if everthying is set right.

c. Review the register settings to make sure interrupts should be
enabled for the IR controller.

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 9 декабря 2009 13:47:46 Andy Walls wrote:
> On Tue, 2009-12-08 at 19:59 +0200, Igor M. Liplianin wrote:
> > On 7 декабря 2009 05:35:46 Andy Walls wrote:
> > > Igor and Matthias,
> > >
> > > Please try the changes that I have for the TeVii S470 that are here:
> > >
> > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> > >
> > > You will want to modprobe the driver modules like this to get debugging
> > > information:
> > >
> > > 	# modprobe cx25840 ir_debug=2
> > > 	# modprobe cx23885 ir_input_debug=1
> > >
> > > With that debugging you will get output something like this in dmesg or
> > > your logs when you press a button on the remote (this is RC-5 using a
> > > CX23888 chip not NEC using a CX23885 chip):
> > >
> > > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > > cx23885[0]/888-ir: IRQ Status:  tsr rsr             rby
> > > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > > cx23885[0]/888-ir: IRQ Status:  tsr     rto
> > > cx23885[0]/888-ir: IRQ Enables:     rse rte roe
> > > cx23885[0]/888-ir: rx read:     817000 ns  mark
> > > cx23885[0]/888-ir: rx read:     838926 ns  space
> > > cx23885[0]/888-ir: rx read:    1572259 ns  mark
> > > cx23885[0]/888-ir: rx read:    1705296 ns  space
> > > [...]
> > > cx23885[0]/888-ir: rx read:     838037 ns  space
> > > cx23885[0]/888-ir: rx read:     746333 ns  mark
> > > cx23885[0]/888-ir: rx read:    1705741 ns  space
> > > cx23885[0]/888-ir: rx read:    1619370 ns  mark
> > > cx23885[0]/888-ir: rx read: end of rx
> > >
> > > If you do not see good or many NEC timing measurments in the logs, the
> > > first thing to try is to change lines 533-534 of
> > > linux/drivers/media/cx23885/cx23885-input.c:
> > >
> > >                params.modulation = true;
> > >                params.invert_level = false;
> > >
> > > If you see no timing measurements or few timing measurements, change
> > > the "modulation" to "false".  If the chip is expecting carrier pulses
> > > and an external circuit or capacitor is smoothing carrier bursts into
> > > baseband pulses, then the hardware won't make measurements properly.
> > >
> > > If you see inverted mark and space inverted when "modulation" is set to
> > > "false", then set "invert_level" to "true".
> > >
> > > Those are the two things I had to really guess at.
> > >
> > > Regards,
> > > Andy
> >
> > No luck :(
> > Nothing in logs
> >
> :(
>
> OK.
>
> 1. I assume you have the v4l-cx23885-avcore-01.fw file available for the
> cx25840 module, just so there is no problem initializing the CX23885 AV
> core.
>
>
> 2. Does dmesg or the logs show the input device being created?
> Somewhere in the log you should see:
>
> 	"cx23885 IR (TeVii S470)"
>
> when the input device is created.
>
>
> 3. With the "debug=7" option to the cx23885 module, do you see any IR
> interrupts coming in?  In dmesg or the log you should see:
>
> 	"(PCI_MSK_IR        0x...)"
>
> when an IR interrupt happens.

cx25840 3-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
cx25840 3-0044: firmware: requesting v4l-cx23885-avcore-01.fw
cx25840 3-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes)
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
DS3000 chip version: 0.192 attached.
DVB: registering new adapter (cx23885[0])
dvb_register_frontend
DVB: registering adapter 0 frontend 0 (Montage Technology DS3000/TS2020)...
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xfea00000
cx23885 0000:02:00.0: setting latency timer to 64
IRQ 16/cx23885[0]: IRQF_DISABLED is not guaranteed on shared IRQs
input: cx23885 IR (TeVii S470) as /class/input/input5

That's all.

In fact some time ago I was writing some code for cx23885 IR, but not reached IR interrupts to 
work. Though I used PCI_MSK_AV_CORE (1 << 27), then test register PIN_CTRL for field 
FLD_IR_IRQ_STAT.

I have Compro E650F with RC6 remote, also have RC5 remote from TV set.
I will made little hack to test Compro & RC5.


>
>
> Tonight I will:
>
> a. Add a guess at HVR-1800 support so maybe Steve can help us debug as
> well.  I know the NEC decoder works; I tested it.  What I don't know is
> if the CX23885 AV IR implementation works (I don't have CX23885 hardware
> at the moment).
>
> b. Add a temporary patch to add a /dev/videoN node for the TeVii S470 so
> you can use "v4l2-ctl --log-status" to show the status of the IR
> controller and v4l2-dbg to dump the cx23885 and cx23885-av-core
> registers, so I can see if everthying is set right.
>
> c. Review the register settings to make sure interrupts should be
> enabled for the IR controller.
>
> Regards,
> Andy

-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > Igor and Matthias,
> > > >
> > > > Please try the changes that I have for the TeVii S470 that are here:
> > > >
> > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> > > >


> In fact some time ago I was writing some code for cx23885 IR, but not reached IR interrupts to 
> work. Though I used PCI_MSK_AV_CORE (1 << 27), then test register PIN_CTRL for field 
> FLD_IR_IRQ_STAT.

Igor,

You are exactly right on this.  I used the wrong interrupt status flag.
I have pushed a patch to my repository to use the PCI_MSK_AV_CORE status
flag.

Could you please update an test the TeVii S470 again when you have time?


> I have Compro E650F with RC6 remote, also have RC5 remote from TV set.
> I will made little hack to test Compro & RC5.

OK. Thank you.

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 10 декабря 2009 03:12:39 Andy Walls wrote:
> On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > > Igor and Matthias,
> > > > >
> > > > > Please try the changes that I have for the TeVii S470 that are
> > > > > here:
> > > > >
> > > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> >
> > In fact some time ago I was writing some code for cx23885 IR, but not
> > reached IR interrupts to work. Though I used PCI_MSK_AV_CORE (1 << 27),
> > then test register PIN_CTRL for field FLD_IR_IRQ_STAT.
>
> Igor,
>
> You are exactly right on this.  I used the wrong interrupt status flag.
> I have pushed a patch to my repository to use the PCI_MSK_AV_CORE status
> flag.
>
> Could you please update an test the TeVii S470 again when you have time?
>
> > I have Compro E650F with RC6 remote, also have RC5 remote from TV set.
> > I will made little hack to test Compro & RC5.
>
> OK. Thank you.
>
> Regards,
> Andy
First try, without pressing IR keys

cx25840 3-0044: IRQ Enables:     rse rte roe
cx25840 3-0044: IRQ Status:  tsr                    
cx25840 3-0044: IRQ Enables:     rse rte roe
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 0, comm: swapper Not tainted 2.6.32 #2
Call Trace:
 [<c1052db0>] ? __report_bad_irq+0x24/0x69
 [<c1052db7>] ? __report_bad_irq+0x2b/0x69
 [<c1052edc>] ? note_interrupt+0xe7/0x13f
 [<c1053416>] ? handle_fasteoi_irq+0x7a/0x97
 [<c1004411>] ? handle_irq+0x38/0x3f
 [<c1003bd1>] ? do_IRQ+0x38/0x89
 [<c1002ea9>] ? common_interrupt+0x29/0x30
 [<c1007a1e>] ? mwait_idle+0x7a/0x7f
 [<c1001b93>] ? cpu_idle+0x37/0x4c
handlers:
[<c13179ad>] (usb_hcd_irq+0x0/0x59)
[<f85ba5e7>] (azx_interrupt+0x0/0xe7 [snd_hda_intel])
[<f88b1d2b>] (cx23885_irq+0x0/0x4a5 [cx23885])
Disabling IRQ #16
cx25840 3-0044: IRQ Status:  tsr                    
cx25840 3-0044: IRQ Enables:     rse rte roe
cx25840 3-0044: IRQ Status:  tsr                    

Sorry for not speaking to much :)
-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Thu, 2009-12-10 at 18:16 +0200, Igor M. Liplianin wrote:
> On 10 декабря 2009 03:12:39 Andy Walls wrote:
> > On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > > > Igor and Matthias,
> > > > > >
> > > > > > Please try the changes that I have for the TeVii S470 that are
> > > > > > here:
> > > > > >
> > > > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> > >
> > > In fact some time ago I was writing some code for cx23885 IR, but not
> > > reached IR interrupts to work. Though I used PCI_MSK_AV_CORE (1 << 27),
> > > then test register PIN_CTRL for field FLD_IR_IRQ_STAT.
> >
> > Igor,
> >
> > You are exactly right on this.  I used the wrong interrupt status flag.
> > I have pushed a patch to my repository to use the PCI_MSK_AV_CORE status
> > flag.
> >
> > Could you please update an test the TeVii S470 again when you have time?
> >
> > > I have Compro E650F with RC6 remote, also have RC5 remote from TV set.
> > > I will made little hack to test Compro & RC5.
> >
> > OK. Thank you.
> >
> > Regards,
> > Andy
> First try, without pressing IR keys
> 
> cx25840 3-0044: IRQ Enables:     rse rte roe
> cx25840 3-0044: IRQ Status:  tsr                    
> cx25840 3-0044: IRQ Enables:     rse rte roe
> irq 16: nobody cared (try booting with the "irqpoll" option)
> Pid: 0, comm: swapper Not tainted 2.6.32 #2
> Call Trace:
>  [<c1052db0>] ? __report_bad_irq+0x24/0x69
>  [<c1052db7>] ? __report_bad_irq+0x2b/0x69
>  [<c1052edc>] ? note_interrupt+0xe7/0x13f
>  [<c1053416>] ? handle_fasteoi_irq+0x7a/0x97
>  [<c1004411>] ? handle_irq+0x38/0x3f
>  [<c1003bd1>] ? do_IRQ+0x38/0x89
>  [<c1002ea9>] ? common_interrupt+0x29/0x30
>  [<c1007a1e>] ? mwait_idle+0x7a/0x7f
>  [<c1001b93>] ? cpu_idle+0x37/0x4c
> handlers:
> [<c13179ad>] (usb_hcd_irq+0x0/0x59)
> [<f85ba5e7>] (azx_interrupt+0x0/0xe7 [snd_hda_intel])
> [<f88b1d2b>] (cx23885_irq+0x0/0x4a5 [cx23885])
> Disabling IRQ #16
> cx25840 3-0044: IRQ Status:  tsr                    
> cx25840 3-0044: IRQ Enables:     rse rte roe
> cx25840 3-0044: IRQ Status:  tsr                    

OK.  We're getting interrupts from the A/V core, but they are not IR
related.  They must be audio and video interrupts from the A/V core.

I have checked in new changes:

	http://linuxtv.org/hg/~awalls/cx23885-ir

please try again when you have time.

	# modprobe cx25840 debug=2 ir_debug=2
	# modprobe cx23885 debug=7

My only concern now, is that I have not turned off all the audio
interrupts from the A/V core - I could not determine if registers
0x80c-0x80f were improtant to set.

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 11 декабря 2009, "Igor M. Liplianin" <liplianin@me.by> wrote:
> On Thu, 2009-12-10 at 18:16 +0200, Igor M. Liplianin wrote:
> > On 10 декабря 2009 03:12:39 Andy Walls wrote:
> > > On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > > > > Igor and Matthias,
> > > > > > >
> > > > > > > Please try the changes that I have for the TeVii S470 that are
> > > > > > > here:
> > > > > > >
> > > > > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> > > >
> > > > In fact some time ago I was writing some code for cx23885 IR, but not
> > > > reached IR interrupts to work. Though I used PCI_MSK_AV_CORE (1 <<
> > > > 27), then test register PIN_CTRL for field FLD_IR_IRQ_STAT.
> > >
> > > Igor,
> > >
> > > You are exactly right on this.  I used the wrong interrupt status flag.
> > > I have pushed a patch to my repository to use the PCI_MSK_AV_CORE
> > > status flag.
> > >
> > > Could you please update an test the TeVii S470 again when you have
> > > time?
> > >
> > > > I have Compro E650F with RC6 remote, also have RC5 remote from TV
> > > > set. I will made little hack to test Compro & RC5.
> > >
> > > OK. Thank you.
> > >
> > > Regards,
> > > Andy
> >
> > First try, without pressing IR keys
> >
> > cx25840 3-0044: IRQ Enables:     rse rte roe
> > cx25840 3-0044: IRQ Status:  tsr
> > cx25840 3-0044: IRQ Enables:     rse rte roe
> > irq 16: nobody cared (try booting with the "irqpoll" option)
> > Pid: 0, comm: swapper Not tainted 2.6.32 #2
> > Call Trace:
> >  [<c1052db0>] ? __report_bad_irq+0x24/0x69
> >  [<c1052db7>] ? __report_bad_irq+0x2b/0x69
> >  [<c1052edc>] ? note_interrupt+0xe7/0x13f
> >  [<c1053416>] ? handle_fasteoi_irq+0x7a/0x97
> >  [<c1004411>] ? handle_irq+0x38/0x3f
> >  [<c1003bd1>] ? do_IRQ+0x38/0x89
> >  [<c1002ea9>] ? common_interrupt+0x29/0x30
> >  [<c1007a1e>] ? mwait_idle+0x7a/0x7f
> >  [<c1001b93>] ? cpu_idle+0x37/0x4c
> > handlers:
> > [<c13179ad>] (usb_hcd_irq+0x0/0x59)
> > [<f85ba5e7>] (azx_interrupt+0x0/0xe7 [snd_hda_intel])
> > [<f88b1d2b>] (cx23885_irq+0x0/0x4a5 [cx23885])
> > Disabling IRQ #16
> > cx25840 3-0044: IRQ Status:  tsr
> > cx25840 3-0044: IRQ Enables:     rse rte roe
> > cx25840 3-0044: IRQ Status:  tsr
>
> OK.  We're getting interrupts from the A/V core, but they are not IR
> related.  They must be audio and video interrupts from the A/V core.
>
> I have checked in new changes:
>
> 	http://linuxtv.org/hg/~awalls/cx23885-ir
>
> please try again when you have time.
>
> 	# modprobe cx25840 debug=2 ir_debug=2
> 	# modprobe cx23885 debug=7
>
> My only concern now, is that I have not turned off all the audio
> interrupts from the A/V core - I could not determine if registers
> 0x80c-0x80f were improtant to set.
>
> Regards,
> Andy
dmesg is full of repeated lines:

cx25840 3-0044: AV Core IRQ status (entry):           
cx25840 3-0044: AV Core IRQ status (exit):           
cx23885[0]/0: pci_status: 0x083f4000  pci_mask: 0x08000001
cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x20
cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count: 0xc7383f3a
cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)


Igor

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Sat, 2009-12-12 at 02:30 +0200, Igor M. Liplianin wrote:
> On 11 декабря 2009, "Igor M. Liplianin" <liplianin@me.by> wrote:
> > On Thu, 2009-12-10 at 18:16 +0200, Igor M. Liplianin wrote:
> > > On 10 декабря 2009 03:12:39 Andy Walls wrote:
> > > > On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > > > > > Igor and Matthias,
> > > > > > > >
> > > > > > > > Please try the changes that I have for the TeVii S470 that are
> > > > > > > > here:
> > > > > > > >
> > > > > > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir

> > > First try, without pressing IR keys
> > >
> > > cx25840 3-0044: IRQ Enables:     rse rte roe
> > > cx25840 3-0044: IRQ Status:  tsr
> > > cx25840 3-0044: IRQ Enables:     rse rte roe
> > > irq 16: nobody cared (try booting with the "irqpoll" option)

> > please try again when you have time.
> >
> > 	# modprobe cx25840 debug=2 ir_debug=2
> > 	# modprobe cx23885 debug=7
> >
> dmesg is full of repeated lines:
> 
> cx25840 3-0044: AV Core IRQ status (entry):           
> cx25840 3-0044: AV Core IRQ status (exit):           

A strange thing here is that under this condition my changes should
never claim the AV Core interrupt is "handled".  I don't know why you
didn't get the "nobody cared" message again.

> cx23885[0]/0: pci_status: 0x083f4000  pci_mask: 0x08000001
> cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
> cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x20
> cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count: 0xc7383f3a
> cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)

I'll read over the documentation again to see if I missed something.
I'll have some changes later tonight that will always try to clear every
interrupt that the AV Core could possibly generate.

-Andy

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 12 декабря 2009 03:00:37 Andy Walls wrote:
> On Sat, 2009-12-12 at 02:30 +0200, Igor M. Liplianin wrote:
> > On 11 декабря 2009, "Igor M. Liplianin" <liplianin@me.by> wrote:
> > > On Thu, 2009-12-10 at 18:16 +0200, Igor M. Liplianin wrote:
> > > > On 10 декабря 2009 03:12:39 Andy Walls wrote:
> > > > > On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > > > > > > Igor and Matthias,
> > > > > > > > >
> > > > > > > > > Please try the changes that I have for the TeVii S470 that
> > > > > > > > > are here:
> > > > > > > > >
> > > > > > > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> > > >
> > > > First try, without pressing IR keys
> > > >
> > > > cx25840 3-0044: IRQ Enables:     rse rte roe
> > > > cx25840 3-0044: IRQ Status:  tsr
> > > > cx25840 3-0044: IRQ Enables:     rse rte roe
> > > > irq 16: nobody cared (try booting with the "irqpoll" option)
> > >
> > > please try again when you have time.
> > >
> > > 	# modprobe cx25840 debug=2 ir_debug=2
> > > 	# modprobe cx23885 debug=7
> >
> > dmesg is full of repeated lines:
> >
> > cx25840 3-0044: AV Core IRQ status (entry):
> > cx25840 3-0044: AV Core IRQ status (exit):
>
> A strange thing here is that under this condition my changes should
> never claim the AV Core interrupt is "handled".  I don't know why you
> didn't get the "nobody cared" message again.
I did, but not frequently. I thought it is obvious :)

cx23885[0]/0: pci_status: 0x083f4000  pci_mask: 0x08000001
cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x20
cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count: 0xc7383f3a
cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)
cx25840 3-0044: AV Core IRQ status (entry):           
cx25840 3-0044: AV Core IRQ status (exit):           
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 2521, comm: syslogd Not tainted 2.6.32 #2
Call Trace:
 [<c1052db0>] ? __report_bad_irq+0x24/0x69
 [<c1052db7>] ? __report_bad_irq+0x2b/0x69
 [<c1052edc>] ? note_interrupt+0xe7/0x13f
 [<c1053416>] ? handle_fasteoi_irq+0x7a/0x97
 [<c1004411>] ? handle_irq+0x38/0x3f
 [<c1003bd1>] ? do_IRQ+0x38/0x89
 [<c1002ea9>] ? common_interrupt+0x29/0x30
handlers:
[<c13179ad>] (usb_hcd_irq+0x0/0x59)
[<f86275e7>] (azx_interrupt+0x0/0xe7 [snd_hda_intel])
[<f88a8d2b>] (cx23885_irq+0x0/0x4e1 [cx23885])
Disabling IRQ #16
cx23885[0]/0: pci_status: 0x083f4000  pci_mask: 0x08000001
cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x20
cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count: 0xc7383f3a
cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)

Igor

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Sat, 2009-12-12 at 03:42 +0200, Igor M. Liplianin wrote:
> On 12 декабря 2009 03:00:37 Andy Walls wrote:
> > On Sat, 2009-12-12 at 02:30 +0200, Igor M. Liplianin wrote:
> > > On 11 декабря 2009, "Igor M. Liplianin" <liplianin@me.by> wrote:
> > > > On Thu, 2009-12-10 at 18:16 +0200, Igor M. Liplianin wrote:
> > > > > On 10 декабря 2009 03:12:39 Andy Walls wrote:
> > > > > > On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > > > > > > > Igor and Matthias,
> > > > > > > > > >
> > > > > > > > > > Please try the changes that I have for the TeVii S470 that
> > > > > > > > > > are here:
> > > > > > > > > >
> > > > > > > > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> > > > >
> > > > > First try, without pressing IR keys
> > > > >
> > > > > cx25840 3-0044: IRQ Enables:     rse rte roe
> > > > > cx25840 3-0044: IRQ Status:  tsr
> > > > > cx25840 3-0044: IRQ Enables:     rse rte roe
> > > > > irq 16: nobody cared (try booting with the "irqpoll" option)
> > > >
> > > > please try again when you have time.
> > > >
> > > > 	# modprobe cx25840 debug=2 ir_debug=2
> > > > 	# modprobe cx23885 debug=7
> > >
> > > dmesg is full of repeated lines:
> > >
> > > cx25840 3-0044: AV Core IRQ status (entry):
> > > cx25840 3-0044: AV Core IRQ status (exit):
> >
> > A strange thing here is that under this condition my changes should
> > never claim the AV Core interrupt is "handled".  I don't know why you
> > didn't get the "nobody cared" message again.
> I did, but not frequently. I thought it is obvious :)

OK, that's better. :P

I have checked in more changes, please try when you get the chance.

Please be aware that I reconfigured the drive of one signal PAD in the
AV Core - I'm hoping to stop false interrupts.  I did not reconfigure
the corresponding IO pin in the bridge driver - I left it at whatever
was the default.  


(I think I'm going to have to buy a CX23885 based card soon...)

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 12 декабря 2009 04:58:48 Andy Walls wrote:
> On Sat, 2009-12-12 at 03:42 +0200, Igor M. Liplianin wrote:
> > On 12 декабря 2009 03:00:37 Andy Walls wrote:
> > > On Sat, 2009-12-12 at 02:30 +0200, Igor M. Liplianin wrote:
> > > > On 11 декабря 2009, "Igor M. Liplianin" <liplianin@me.by> wrote:
> > > > > On Thu, 2009-12-10 at 18:16 +0200, Igor M. Liplianin wrote:
> > > > > > On 10 декабря 2009 03:12:39 Andy Walls wrote:
> > > > > > > On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > > > > > > > > Igor and Matthias,
> > > > > > > > > > >
> > > > > > > > > > > Please try the changes that I have for the TeVii S470
> > > > > > > > > > > that are here:
> > > > > > > > > > >
> > > > > > > > > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> > > > > >
> > > > > > First try, without pressing IR keys
> > > > > >
> > > > > > cx25840 3-0044: IRQ Enables:     rse rte roe
> > > > > > cx25840 3-0044: IRQ Status:  tsr
> > > > > > cx25840 3-0044: IRQ Enables:     rse rte roe
> > > > > > irq 16: nobody cared (try booting with the "irqpoll" option)
> > > > >
> > > > > please try again when you have time.
> > > > >
> > > > > 	# modprobe cx25840 debug=2 ir_debug=2
> > > > > 	# modprobe cx23885 debug=7
> > > >
> > > > dmesg is full of repeated lines:
> > > >
> > > > cx25840 3-0044: AV Core IRQ status (entry):
> > > > cx25840 3-0044: AV Core IRQ status (exit):
> > >
> > > A strange thing here is that under this condition my changes should
> > > never claim the AV Core interrupt is "handled".  I don't know why you
> > > didn't get the "nobody cared" message again.
> >
> > I did, but not frequently. I thought it is obvious :)
>
> OK, that's better. :P
>
> I have checked in more changes, please try when you get the chance.
>
> Please be aware that I reconfigured the drive of one signal PAD in the
> AV Core - I'm hoping to stop false interrupts.  I did not reconfigure
> the corresponding IO pin in the bridge driver - I left it at whatever
> was the default.

cx23885[0]/0: pci_status: 0x08304000  pci_mask: 0x08000000
cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count: 0x47381f2a
cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)
cx25840 3-0044: AV Core IRQ status (entry): ir        
cx25840 3-0044: IRQ Status:  tsr                    
cx25840 3-0044: IRQ Enables:     rse rte roe
cx25840 3-0044: AV Core audio IRQ status: 0x80
cx25840 3-0044: AV Core audio MC IRQ status: 0x20000000
cx25840 3-0044: AV Core video IRQ status: 0x0002
cx25840 3-0044: AV Core IRQ status (exit): ir        
cx23885[0]/0: pci_status: 0x08004000  pci_mask: 0x08000000
cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count: 0x47381f2a
cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)
cx25840 3-0044: AV Core IRQ status (entry): ir        
cx25840 3-0044: IRQ Status:  tsr                    
cx25840 3-0044: IRQ Enables:     rse rte roe
cx25840 3-0044: AV Core audio IRQ status: 0x80
cx25840 3-0044: AV Core audio MC IRQ status: 0x20000000
cx25840 3-0044: AV Core video IRQ status: 0x0002
cx25840 3-0044: AV Core IRQ status (exit): ir        
cx23885[0]/0: pci_status: 0x08304000  pci_mask: 0x08000000
cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count: 0x47381f2a
cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)
cx25840 3-0044: AV Core IRQ status (entry): ir        
cx25840 3-0044: IRQ Status:  tsr                    
cx25840 3-0044: IRQ Enables:     rse rte roe
cx25840 3-0044: AV Core audio IRQ status: 0x80
cx25840 3-0044: AV Core audio MC IRQ status: 0x20000000
cx25840 3-0044: AV Core video IRQ status: 0x0123
cx25840 3-0044: AV Core IRQ status (exit): ir        
cx23885[0]/0: pci_status: 0x08004000  pci_mask: 0x08000000
cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x0
cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count: 0x47381f2a
cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)
cx25840 3-0044: AV Core IRQ status (entry): ir        

>
>
> (I think I'm going to have to buy a CX23885 based card soon...)
>
> Regards,
> Andy

-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Sat, 2009-12-12 at 13:49 +0200, Igor M. Liplianin wrote:
> On 12 декабря 2009 04:58:48 Andy Walls wrote:
> > On Sat, 2009-12-12 at 03:42 +0200, Igor M. Liplianin wrote:
> > > On 12 декабря 2009 03:00:37 Andy Walls wrote:
> > > > On Sat, 2009-12-12 at 02:30 +0200, Igor M. Liplianin wrote:
> > > > > On 11 декабря 2009, "Igor M. Liplianin" <liplianin@me.by> wrote:
> > > > > > On Thu, 2009-12-10 at 18:16 +0200, Igor M. Liplianin wrote:
> > > > > > > On 10 декабря 2009 03:12:39 Andy Walls wrote:
> > > > > > > > On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > > > > > > > > > Igor and Matthias,
> > > > > > > > > > > >
> > > > > > > > > > > > Please try the changes that I have for the TeVii S470
> > > > > > > > > > > > that are here:
> > > > > > > > > > > >
> > > > > > > > > > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> > > > > > >

> >
> > I have checked in more changes, please try when you get the chance.

> cx23885[0]/0: pci_status: 0x08304000  pci_mask: 0x08000000
> cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
> cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x0
> cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count: 0x47381f2a
> cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)

> cx25840 3-0044: AV Core IRQ status (entry): ir        
> cx25840 3-0044: IRQ Status:  tsr                    
> cx25840 3-0044: IRQ Enables:     rse rte roe

?! 

Those three lines make no sense together.  Maybe I should take out the
V4L2_SUBDEV_IO_PIN_ACTIVE_LOW setting in cx23885-cards.c.

I'm going to have to buy some hardware and experiment for myself.


BTW, what happens you press a button on an NEC remote?

Thanks for all your help.

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 12 декабря 2009 16:15:27 Andy Walls wrote:
> On Sat, 2009-12-12 at 13:49 +0200, Igor M. Liplianin wrote:
> > On 12 декабря 2009 04:58:48 Andy Walls wrote:
> > > On Sat, 2009-12-12 at 03:42 +0200, Igor M. Liplianin wrote:
> > > > On 12 декабря 2009 03:00:37 Andy Walls wrote:
> > > > > On Sat, 2009-12-12 at 02:30 +0200, Igor M. Liplianin wrote:
> > > > > > On 11 декабря 2009, "Igor M. Liplianin" <liplianin@me.by> wrote:
> > > > > > > On Thu, 2009-12-10 at 18:16 +0200, Igor M. Liplianin wrote:
> > > > > > > > On 10 декабря 2009 03:12:39 Andy Walls wrote:
> > > > > > > > > On Wed, 2009-12-09 at 17:54 +0200, Igor M. Liplianin wrote:
> > > > > > > > > > > > > Igor and Matthias,
> > > > > > > > > > > > >
> > > > > > > > > > > > > Please try the changes that I have for the TeVii
> > > > > > > > > > > > > S470 that are here:
> > > > > > > > > > > > >
> > > > > > > > > > > > > 	http://linuxtv.org/hg/~awalls/cx23885-ir
> > >
> > > I have checked in more changes, please try when you get the chance.
> >
> > cx23885[0]/0: pci_status: 0x08304000  pci_mask: 0x08000000
> > cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000 count: 0x0
> > cx23885[0]/0: ts1_status: 0x00000000  ts1_mask: 0x00000000 count: 0x0
> > cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count:
> > 0x47381f2a cx23885[0]/0:  (PCI_MSK_AV_CORE   0x08000000)
> >
> > cx25840 3-0044: AV Core IRQ status (entry): ir
> > cx25840 3-0044: IRQ Status:  tsr
> > cx25840 3-0044: IRQ Enables:     rse rte roe
>
> ?!
>
> Those three lines make no sense together.  Maybe I should take out the
I know. But it is.
There would be something small, but important, which is missing.


> V4L2_SUBDEV_IO_PIN_ACTIVE_LOW setting in cx23885-cards.c.
Low level raises interrupt by default, as I understand.
But it is configurable.


>
> I'm going to have to buy some hardware and experiment for myself.
I can test your code forever ... Until it success


>
>
> BTW, what happens you press a button on an NEC remote?
Nothing.
But remote is working under m$

>
> Thanks for all your help.
>
> Regards,
> Andy

-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 12 декабря 2009 16:15:27 Andy Walls wrote:
> V4L2_SUBDEV_IO_PIN_ACTIVE_LOW
After I removed this from ir_rx_pin_cfg, interrupts stopped.

-- 
Igor M. Liplianin
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Sat, 2009-12-12 at 18:22 +0200, Igor M. Liplianin wrote:
> On 12 декабря 2009 16:15:27 Andy Walls wrote:
> > V4L2_SUBDEV_IO_PIN_ACTIVE_LOW
> After I removed this from ir_rx_pin_cfg, interrupts stopped.

If we are lucky, that was the problem.

If it was the problem, now it is a matter of setting the 

	params.modulation
	params.invert_level

properly for the TeVii S470 in cx23885-input.c to have the hardware
generate interrupts when it makes a few pulse measurements.


If it was not the problem, then we still have some interrupt(s) coming
from the AV Core and have just supressed all of the interrupts from the
AV Core. :)

Regards,
Andy

Re: IR Receiver on an Tevii S470

[Guillem Solà Aranda]

Hi,

I have a s470 and with

s2-liplianin-7212833be10d
s2-liplianin-ab3a80e883ba

began to work, but today I have tested

s2-liplianin-b663b38d616f

and seems that there are some problems trying to load the driver

Linux video capture interface: v2.00
cx23885: disagrees about version of symbol ir_codes_hauppauge_new_table
cx23885: Unknown symbol ir_codes_hauppauge_new_table
cx23885: disagrees about version of symbol ir_input_init
cx23885: Unknown symbol ir_input_init
cx23885: disagrees about version of symbol ir_input_nokey
cx23885: Unknown symbol ir_input_nokey
cx23885: disagrees about version of symbol ir_input_keydown
cx23885: Unknown symbol ir_input_keydown

I'm running this on a DELL Server with RHEL and kernel 2.6.31.

regards,
Guillem

Re: IR Receiver on an Tevii S470

[Igor M. Liplianin]

On 31 декабря 2009 14:46:49 Guillem Solà Aranda wrote:
> Hi,
>
> I have a s470 and with
>
> s2-liplianin-7212833be10d
> s2-liplianin-ab3a80e883ba
>
> began to work, but today I have tested
>
> s2-liplianin-b663b38d616f
>
> and seems that there are some problems trying to load the driver
>
> Linux video capture interface: v2.00
> cx23885: disagrees about version of symbol ir_codes_hauppauge_new_table
> cx23885: Unknown symbol ir_codes_hauppauge_new_table
> cx23885: disagrees about version of symbol ir_input_init
> cx23885: Unknown symbol ir_input_init
> cx23885: disagrees about version of symbol ir_input_nokey
> cx23885: Unknown symbol ir_input_nokey
> cx23885: disagrees about version of symbol ir_input_keydown
> cx23885: Unknown symbol ir_input_keydown
>
> I'm running this on a DELL Server with RHEL and kernel 2.6.31.
>
> regards,
> Guillem
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
Since module ir-common.ko moved to IR directory just remove old one.

rm /lib/modules/$(uname -r)/kernel/drivers/media/common/ir-common.ko

Happy New Year!

Re: IR Receiver on an Tevii S470

[Andreas Tschirpke]

Andy Walls <awalls <at> radix.net> writes:

> > > please try again when you have time.
> > >
> > > 	# modprobe cx25840 debug=2 ir_debug=2
> > > 	# modprobe cx23885 debug=7
I tried to activate my remote using the driver in
http://linuxtv.org/hg/~awalls/cx23885-ir.
According to the following dmesg output everything is loaded correctly and the
ir interface is registered as /dev/input/event5:

[    9.220413] Linux video capture interface: v2.00
[    9.432581] cx23885 driver version 0.0.2 loaded
[    9.433560] ACPI: PCI Interrupt Link [LN0A] enabled at IRQ 19
[    9.433572]   alloc irq_desc for 19 on node -1
[    9.433577]   alloc kstat_irqs on node -1
[    9.433594] cx23885 0000:02:00.0: PCI INT A -> Link[LN0A] -> GSI 19 (level,
low) -> IRQ 19
[    9.433746] CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470
[card=15,autodetected]
[    9.720071] cx25840 3-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
[    9.728397] cx25840 3-0044: firmware: requesting v4l-cx23885-avcore-01.fw
[    9.994115] HDA Intel 0000:00:08.0: power state changed by ACPI to D0
[    9.995038] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
[    9.995055] HDA Intel 0000:00:08.0: PCI INT A -> Link[LAZA] -> GSI 22 (level,
low) -> IRQ 22
[    9.995139] HDA Intel 0000:00:08.0: setting latency timer to 64
[   10.579145] cx25840 3-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382
bytes)
[   10.586817] cx23885_dvb_register() allocating 1 frontend(s)
[   10.586830] cx23885[0]: cx23885 based dvb card
[   10.593034] hda_codec: Unknown model for ALC662 rev1, trying auto-probe from
BIOS...
[   10.790592] DS3000 chip version: 0.192 attached.
[   10.790604] DVB: registering new adapter (cx23885[0])
[   10.790613] DVB: registering adapter 0 frontend 0 (Montage Technology
DS3000/TS2020)...
[   10.791219] cx23885_dev_checkrevision() Hardware revision = 0xb0
[   10.791236] cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 19, latency: 0,
mmio: 0xfac00000
[   10.791249] cx23885 0000:02:00.0: setting latency timer to 64
[   10.791258] IRQ 19/cx23885[0]: IRQF_DISABLED is not guaranteed on shared IRQs
[   10.795358] input: cx23885 IR (TeVii S470) as
/devices/pci0000:00/0000:00:0c.0/0000:02:00.0/input/input5

But there is no signal comming from input/event5, regardless of the tools trying
to access it (lircd, irw, mode2, inputlircd, plain cat, etc.). What else is
needed to activate the remote with this driver? If I enable debug messages by 
> modprobe cx25840 debug=2 ir_debug=2
> modprobe cx23885 debug=7

the dmesg/syslog is flooded with:
[   75.932848] cx23885[0]/0: [f47e4840/9] wakeup reg=9514 buf=9514
[   75.937811] cx23885[0]/0: pci_status: 0x00008002  pci_mask: 0x08001f02
[   75.937839] cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000
count: 0x0
[   75.937847] cx23885[0]/0: ts1_status: 0x00000001  ts1_mask: 0x00001111 count:
0x252b
[   75.937856] cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count:
0x2ca4d364
[   75.937881] cx23885[0]/0:  (PCI_MSK_VID_B     0x00000002)
[   75.937902] cx23885[0]/0:  (RISCI1            0x00000001)
[   75.937918] cx23885[0]/0: [f47e4000/10] wakeup reg=9515 buf=9515
[   75.937942] cx23885[0]/0: queue is not empty - append to active
[   75.937964] cx23885[0]/0: [f47e4840/9] cx23885_buf_queue - append to active
[   75.938064] cx23885[0]/0: queue is not empty - append to active
[   75.938087] cx23885[0]/0: [f47e4000/10] cx23885_buf_queue - append to active
[   75.942878] cx23885[0]/0: pci_status: 0x00008002  pci_mask: 0x08001f02
[   75.942901] cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000
count: 0x0
[   75.942908] cx23885[0]/0: ts1_status: 0x00000001  ts1_mask: 0x00001111 count:
0x252c
[   75.942917] cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count:
0x2ca4d364
[   75.942943] cx23885[0]/0:  (PCI_MSK_VID_B     0x00000002)
[   75.942949] cx23885[0]/0:  (RISCI1            0x00000001)
[   75.942961] cx23885[0]/0: [f47e4480/11] wakeup reg=9516 buf=9516
[   75.943101] cx23885[0]/0: queue is not empty - append to active
[   75.943112] cx23885[0]/0: [f47e4480/11] cx23885_buf_queue - append to active
...

Any advice where to go from here, what to try?
Thank you.

Andreas

Re: IR Receiver on an Tevii S470

[Andy Walls]

On Wed, 2010-01-06 at 21:21 +0000, Andreas Tschirpke wrote:
> Andy Walls <awalls <at> radix.net> writes:
> 
> > > > please try again when you have time.
> > > >
> > > > 	# modprobe cx25840 debug=2 ir_debug=2
> > > > 	# modprobe cx23885 debug=7
> I tried to activate my remote using the driver in
> http://linuxtv.org/hg/~awalls/cx23885-ir.
> According to the following dmesg output everything is loaded correctly and the
> ir interface is registered as /dev/input/event5:
> 
> [    9.220413] Linux video capture interface: v2.00
> [    9.432581] cx23885 driver version 0.0.2 loaded
> [    9.433560] ACPI: PCI Interrupt Link [LN0A] enabled at IRQ 19
> [    9.433572]   alloc irq_desc for 19 on node -1
> [    9.433577]   alloc kstat_irqs on node -1
> [    9.433594] cx23885 0000:02:00.0: PCI INT A -> Link[LN0A] -> GSI 19 (level,
> low) -> IRQ 19
> [    9.433746] CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470
> [card=15,autodetected]
> [    9.720071] cx25840 3-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
> [    9.728397] cx25840 3-0044: firmware: requesting v4l-cx23885-avcore-01.fw
> [    9.994115] HDA Intel 0000:00:08.0: power state changed by ACPI to D0
> [    9.995038] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
> [    9.995055] HDA Intel 0000:00:08.0: PCI INT A -> Link[LAZA] -> GSI 22 (level,
> low) -> IRQ 22
> [    9.995139] HDA Intel 0000:00:08.0: setting latency timer to 64
> [   10.579145] cx25840 3-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382
> bytes)
> [   10.586817] cx23885_dvb_register() allocating 1 frontend(s)
> [   10.586830] cx23885[0]: cx23885 based dvb card
> [   10.593034] hda_codec: Unknown model for ALC662 rev1, trying auto-probe from
> BIOS...
> [   10.790592] DS3000 chip version: 0.192 attached.
> [   10.790604] DVB: registering new adapter (cx23885[0])
> [   10.790613] DVB: registering adapter 0 frontend 0 (Montage Technology
> DS3000/TS2020)...
> [   10.791219] cx23885_dev_checkrevision() Hardware revision = 0xb0
> [   10.791236] cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 19, latency: 0,
> mmio: 0xfac00000
> [   10.791249] cx23885 0000:02:00.0: setting latency timer to 64
> [   10.791258] IRQ 19/cx23885[0]: IRQF_DISABLED is not guaranteed on shared IRQs
> [   10.795358] input: cx23885 IR (TeVii S470) as
> /devices/pci0000:00/0000:00:0c.0/0000:02:00.0/input/input5
> 
> But there is no signal comming from input/event5, regardless of the tools trying
> to access it (lircd, irw, mode2, inputlircd, plain cat, etc.). What else is
> needed to activate the remote with this driver?

I admire your initiaive, however, that code is not working yet.  The
problem is getting AV core IR interrupts from the CX23885 without
getting a constant stream of AV core interrupts that are not realted to
IR.

I just received a loaner HVR-1250 with a CX23885 from Devin a few days
ago.  It doesn't have the external IR hardware, but it has enough
on-chip for me to debug my interrupt problem using the IR loopback.
Once I have the interrupt problem solved, I'll ask Igor, you, and
whomever else to test.

Life is busy right now.  I might not get to looking at it until Sunday.

Regards,
Andy

>  If I enable debug messages by 
> > modprobe cx25840 debug=2 ir_debug=2
> > modprobe cx23885 debug=7
> 
> the dmesg/syslog is flooded with:
> [   75.932848] cx23885[0]/0: [f47e4840/9] wakeup reg=9514 buf=9514
> [   75.937811] cx23885[0]/0: pci_status: 0x00008002  pci_mask: 0x08001f02
> [   75.937839] cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000
> count: 0x0
> [   75.937847] cx23885[0]/0: ts1_status: 0x00000001  ts1_mask: 0x00001111 count:
> 0x252b
> [   75.937856] cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count:
> 0x2ca4d364
> [   75.937881] cx23885[0]/0:  (PCI_MSK_VID_B     0x00000002)
> [   75.937902] cx23885[0]/0:  (RISCI1            0x00000001)
> [   75.937918] cx23885[0]/0: [f47e4000/10] wakeup reg=9515 buf=9515
> [   75.937942] cx23885[0]/0: queue is not empty - append to active
> [   75.937964] cx23885[0]/0: [f47e4840/9] cx23885_buf_queue - append to active
> [   75.938064] cx23885[0]/0: queue is not empty - append to active
> [   75.938087] cx23885[0]/0: [f47e4000/10] cx23885_buf_queue - append to active
> [   75.942878] cx23885[0]/0: pci_status: 0x00008002  pci_mask: 0x08001f02
> [   75.942901] cx23885[0]/0: vida_status: 0x00000000 vida_mask: 0x00000000
> count: 0x0
> [   75.942908] cx23885[0]/0: ts1_status: 0x00000001  ts1_mask: 0x00001111 count:
> 0x252c
> [   75.942917] cx23885[0]/0: ts2_status: 0x00000000  ts2_mask: 0x00000000 count:
> 0x2ca4d364
> [   75.942943] cx23885[0]/0:  (PCI_MSK_VID_B     0x00000002)
> [   75.942949] cx23885[0]/0:  (RISCI1            0x00000001)
> [   75.942961] cx23885[0]/0: [f47e4480/11] wakeup reg=9516 buf=9516
> [   75.943101] cx23885[0]/0: queue is not empty - append to active
> [   75.943112] cx23885[0]/0: [f47e4480/11] cx23885_buf_queue - append to active
> ...
> 
> Any advice where to go from here, what to try?
> Thank you.
> 
> Andreas
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>