* [RFC v4 1/3] saa7115: Fix saa711x_set_v4lstd for gm7113c
2013-08-03 13:19 [RFC v4 0/3] saa7115: Implement i2c_board_info.platform_data Jon Arne Jørgensen
@ 2013-08-03 13:19 ` Jon Arne Jørgensen
2013-08-03 13:19 ` [RFC v4 2/3] saa7115: Do not load saa7115_init_misc " Jon Arne Jørgensen
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Jon Arne Jørgensen @ 2013-08-03 13:19 UTC (permalink / raw)
To: linux-media
Cc: jonarne, linux-kernel, m.chehab, hans.verkuil, prabhakar.csengg,
laurent.pinchart, andriy.shevchenko, ezequiel.garcia, timo.teras
saa711x_set_v4lstd would toggle several bits that should not be touched
when changing std. This patch fixes this.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
---
drivers/media/i2c/saa7115.c | 37 +++++++++++++------------------------
drivers/media/i2c/saa711x_regs.h | 4 ++++
2 files changed, 17 insertions(+), 24 deletions(-)
diff --git a/drivers/media/i2c/saa7115.c b/drivers/media/i2c/saa7115.c
index 7fd766e..41408dd 100644
--- a/drivers/media/i2c/saa7115.c
+++ b/drivers/media/i2c/saa7115.c
@@ -462,24 +462,6 @@ static const unsigned char saa7115_cfg_50hz_video[] = {
/* ============== SAA7715 VIDEO templates (end) ======= */
-/* ============== GM7113C VIDEO templates ============= */
-static const unsigned char gm7113c_cfg_60hz_video[] = {
- R_08_SYNC_CNTL, 0x68, /* 0xBO: auto detection, 0x68 = NTSC */
- R_0E_CHROMA_CNTL_1, 0x07, /* video autodetection is on */
-
- 0x00, 0x00
-};
-
-static const unsigned char gm7113c_cfg_50hz_video[] = {
- R_08_SYNC_CNTL, 0x28, /* 0x28 = PAL */
- R_0E_CHROMA_CNTL_1, 0x07,
-
- 0x00, 0x00
-};
-
-/* ============== GM7113C VIDEO templates (end) ======= */
-
-
static const unsigned char saa7115_cfg_vbi_on[] = {
R_80_GLOBAL_CNTL_1, 0x00, /* reset tasks */
R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0, /* reset scaler */
@@ -964,17 +946,24 @@ static void saa711x_set_v4lstd(struct v4l2_subdev *sd, v4l2_std_id std)
// This works for NTSC-M, SECAM-L and the 50Hz PAL variants.
if (std & V4L2_STD_525_60) {
v4l2_dbg(1, debug, sd, "decoder set standard 60 Hz\n");
- if (state->ident == GM7113C)
- saa711x_writeregs(sd, gm7113c_cfg_60hz_video);
- else
+ if (state->ident == GM7113C) {
+ u8 reg = saa711x_read(sd, R_08_SYNC_CNTL);
+ reg &= ~(SAA7113_R_08_FSEL | SAA7113_R_08_AUFD);
+ reg |= SAA7113_R_08_FSEL;
+ saa711x_write(sd, R_08_SYNC_CNTL, reg);
+ } else {
saa711x_writeregs(sd, saa7115_cfg_60hz_video);
+ }
saa711x_set_size(sd, 720, 480);
} else {
v4l2_dbg(1, debug, sd, "decoder set standard 50 Hz\n");
- if (state->ident == GM7113C)
- saa711x_writeregs(sd, gm7113c_cfg_50hz_video);
- else
+ if (state->ident == GM7113C) {
+ u8 reg = saa711x_read(sd, R_08_SYNC_CNTL);
+ reg &= ~(SAA7113_R_08_FSEL | SAA7113_R_08_AUFD);
+ saa711x_write(sd, R_08_SYNC_CNTL, reg);
+ } else {
saa711x_writeregs(sd, saa7115_cfg_50hz_video);
+ }
saa711x_set_size(sd, 720, 576);
}
diff --git a/drivers/media/i2c/saa711x_regs.h b/drivers/media/i2c/saa711x_regs.h
index 4e5f2eb..70c56d1 100644
--- a/drivers/media/i2c/saa711x_regs.h
+++ b/drivers/media/i2c/saa711x_regs.h
@@ -201,6 +201,10 @@
#define R_FB_PULSE_C_POS_MSB 0xfb
#define R_FF_S_PLL_MAX_PHASE_ERR_THRESH_NUM_LINES 0xff
+/* SAA7113 bit-masks */
+#define SAA7113_R_08_FSEL 0x40
+#define SAA7113_R_08_AUFD 0x80
+
#if 0
/* Those structs will be used in the future for debug purposes */
struct saa711x_reg_descr {
--
1.8.3.1
^ permalink raw reply related [flat|nested] 5+ messages in thread* [RFC v4 3/3] saa7115: Implement i2c_board_info.platform_data
2013-08-03 13:19 [RFC v4 0/3] saa7115: Implement i2c_board_info.platform_data Jon Arne Jørgensen
2013-08-03 13:19 ` [RFC v4 1/3] saa7115: Fix saa711x_set_v4lstd for gm7113c Jon Arne Jørgensen
2013-08-03 13:19 ` [RFC v4 2/3] saa7115: Do not load saa7115_init_misc " Jon Arne Jørgensen
@ 2013-08-03 13:19 ` Jon Arne Jørgensen
2013-08-08 10:24 ` [RFC v4 0/3] " Hans Verkuil
3 siblings, 0 replies; 5+ messages in thread
From: Jon Arne Jørgensen @ 2013-08-03 13:19 UTC (permalink / raw)
To: linux-media
Cc: jonarne, linux-kernel, m.chehab, hans.verkuil, prabhakar.csengg,
laurent.pinchart, andriy.shevchenko, ezequiel.garcia, timo.teras
This patch implements i2c_board_info.platform_data, and some options to
override the default initialization table for the GM7113C and SAA7113
chips.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
---
drivers/media/i2c/saa7115.c | 128 ++++++++++++++++++++++++++++++++++++---
drivers/media/i2c/saa711x_regs.h | 15 +++++
include/media/saa7115.h | 64 ++++++++++++++++++++
3 files changed, 198 insertions(+), 9 deletions(-)
diff --git a/drivers/media/i2c/saa7115.c b/drivers/media/i2c/saa7115.c
index 17a464d..5cc48f7 100644
--- a/drivers/media/i2c/saa7115.c
+++ b/drivers/media/i2c/saa7115.c
@@ -225,19 +225,59 @@ static const unsigned char saa7111_init[] = {
0x00, 0x00
};
-/* SAA7113/GM7113C init codes
- * It's important that R_14... R_17 == 0x00
- * for the gm7113c chip to deliver stable video
- */
+/* This table has one illegal value, and some values that are not
+ correct according to the datasheet initialization table.
+
+ If you need a table with legal/default values tell the driver in
+ i2c_board_info.platform_data, and you will get the gm7113c_init
+ table instead. */
+
+/* SAA7113 Init codes */
static const unsigned char saa7113_init[] = {
R_01_INC_DELAY, 0x08,
R_02_INPUT_CNTL_1, 0xc2,
R_03_INPUT_CNTL_2, 0x30,
R_04_INPUT_CNTL_3, 0x00,
R_05_INPUT_CNTL_4, 0x00,
- R_06_H_SYNC_START, 0x89,
+ R_06_H_SYNC_START, 0x89, /* Illegal value -119,
+ * min. value = -108 (0x94) */
+ R_07_H_SYNC_STOP, 0x0d,
+ R_08_SYNC_CNTL, 0x88, /* Not datasheet default.
+ * HTC = VTR mode, should be 0x98 */
+ R_09_LUMA_CNTL, 0x01,
+ R_0A_LUMA_BRIGHT_CNTL, 0x80,
+ R_0B_LUMA_CONTRAST_CNTL, 0x47,
+ R_0C_CHROMA_SAT_CNTL, 0x40,
+ R_0D_CHROMA_HUE_CNTL, 0x00,
+ R_0E_CHROMA_CNTL_1, 0x01,
+ R_0F_CHROMA_GAIN_CNTL, 0x2a,
+ R_10_CHROMA_CNTL_2, 0x08, /* Not datsheet default.
+ * VRLN enabled, should be 0x00 */
+ R_11_MODE_DELAY_CNTL, 0x0c,
+ R_12_RT_SIGNAL_CNTL, 0x07, /* Not datasheet default,
+ * should be 0x01 */
+ R_13_RT_X_PORT_OUT_CNTL, 0x00,
+ R_14_ANAL_ADC_COMPAT_CNTL, 0x00,
+ R_15_VGATE_START_FID_CHG, 0x00,
+ R_16_VGATE_STOP, 0x00,
+ R_17_MISC_VGATE_CONF_AND_MSB, 0x00,
+
+ 0x00, 0x00
+};
+
+/* GM7113C is a clone of the SAA7113 chip
+ This init table is copied out of the saa7113 datasheet.
+ In R_08 we enable "Automatic Field Detection" [AUFD],
+ this is disabled when saa711x_set_v4lstd is called. */
+static const unsigned char gm7113c_init[] = {
+ R_01_INC_DELAY, 0x08,
+ R_02_INPUT_CNTL_1, 0xc0,
+ R_03_INPUT_CNTL_2, 0x33,
+ R_04_INPUT_CNTL_3, 0x00,
+ R_05_INPUT_CNTL_4, 0x00,
+ R_06_H_SYNC_START, 0xe9,
R_07_H_SYNC_STOP, 0x0d,
- R_08_SYNC_CNTL, 0x88,
+ R_08_SYNC_CNTL, 0x98,
R_09_LUMA_CNTL, 0x01,
R_0A_LUMA_BRIGHT_CNTL, 0x80,
R_0B_LUMA_CONTRAST_CNTL, 0x47,
@@ -245,9 +285,9 @@ static const unsigned char saa7113_init[] = {
R_0D_CHROMA_HUE_CNTL, 0x00,
R_0E_CHROMA_CNTL_1, 0x01,
R_0F_CHROMA_GAIN_CNTL, 0x2a,
- R_10_CHROMA_CNTL_2, 0x08,
+ R_10_CHROMA_CNTL_2, 0x00,
R_11_MODE_DELAY_CNTL, 0x0c,
- R_12_RT_SIGNAL_CNTL, 0x07,
+ R_12_RT_SIGNAL_CNTL, 0x01,
R_13_RT_X_PORT_OUT_CNTL, 0x00,
R_14_ANAL_ADC_COMPAT_CNTL, 0x00,
R_15_VGATE_START_FID_CHG, 0x00,
@@ -1585,6 +1625,65 @@ static const struct v4l2_subdev_ops saa711x_ops = {
/* ----------------------------------------------------------------------- */
+static void saa711x_write_platform_data(struct saa711x_state *state,
+ struct saa7115_platform_data *data)
+{
+ struct v4l2_subdev *sd = &state->sd;
+ u8 work;
+
+ if (state->ident != GM7113C &&
+ state->ident != SAA7113)
+ return;
+
+ if (data->saa7113_r08_htc) {
+ work = saa711x_read(sd, R_08_SYNC_CNTL);
+ work &= ~SAA7113_R_08_HTC_MASK;
+ work |= ((*data->saa7113_r08_htc) << SAA7113_R_08_HTC_OFFSET);
+ saa711x_write(sd, R_08_SYNC_CNTL, work);
+ }
+
+ if (data->saa7113_r10_vrln) {
+ work = saa711x_read(sd, R_10_CHROMA_CNTL_2);
+ work &= ~SAA7113_R_10_VRLN_MASK;
+ if (*data->saa7113_r10_vrln)
+ work |= (1 << SAA7113_R_10_VRLN_OFFSET);
+ saa711x_write(sd, R_10_CHROMA_CNTL_2, work);
+ }
+
+ if (data->saa7113_r10_ofts) {
+ work = saa711x_read(sd, R_10_CHROMA_CNTL_2);
+ work &= ~SAA7113_R_10_OFTS_MASK;
+ work |= (*data->saa7113_r10_ofts << SAA7113_R_10_OFTS_OFFSET);
+ saa711x_write(sd, R_10_CHROMA_CNTL_2, work);
+ }
+
+ if (data->saa7113_r12_rts0) {
+ work = saa711x_read(sd, R_12_RT_SIGNAL_CNTL);
+ work &= ~SAA7113_R_12_RTS0_MASK;
+ work |= (*data->saa7113_r12_rts0 << SAA7113_R_12_RTS0_OFFSET);
+
+ /* According to the datasheet,
+ * SAA7113_RTS_DOT_IN should only be used on RTS1 */
+ WARN_ON(*data->saa7113_r12_rts0 == SAA7113_RTS_DOT_IN);
+ saa711x_write(sd, R_12_RT_SIGNAL_CNTL, work);
+ }
+
+ if (data->saa7113_r12_rts1) {
+ work = saa711x_read(sd, R_12_RT_SIGNAL_CNTL);
+ work &= ~SAA7113_R_12_RTS1_MASK;
+ work |= (*data->saa7113_r12_rts1 << SAA7113_R_12_RTS1_OFFSET);
+ saa711x_write(sd, R_12_RT_SIGNAL_CNTL, work);
+ }
+
+ if (data->saa7113_r13_adlsb) {
+ work = saa711x_read(sd, R_13_RT_X_PORT_OUT_CNTL);
+ work &= ~SAA7113_R_13_ADLSB_MASK;
+ if (*data->saa7113_r13_adlsb)
+ work |= (1 << SAA7113_R_13_ADLSB_OFFSET);
+ saa711x_write(sd, R_13_RT_X_PORT_OUT_CNTL, work);
+ }
+}
+
/**
* saa711x_detect_chip - Detects the saa711x (or clone) variant
* @client: I2C client structure.
@@ -1693,6 +1792,7 @@ static int saa711x_probe(struct i2c_client *client,
struct saa711x_state *state;
struct v4l2_subdev *sd;
struct v4l2_ctrl_handler *hdl;
+ struct saa7115_platform_data *pdata;
int ident;
char name[CHIP_VER_SIZE + 1];
@@ -1756,14 +1856,20 @@ static int saa711x_probe(struct i2c_client *client,
/* init to 60hz/48khz */
state->crystal_freq = SAA7115_FREQ_24_576_MHZ;
+ pdata = client->dev.platform_data;
switch (state->ident) {
case SAA7111:
case SAA7111A:
saa711x_writeregs(sd, saa7111_init);
break;
case GM7113C:
+ saa711x_writeregs(sd, gm7113c_init);
+ break;
case SAA7113:
- saa711x_writeregs(sd, saa7113_init);
+ if (pdata && pdata->saa7113_force_gm7113c_init)
+ saa711x_writeregs(sd, gm7113c_init);
+ else
+ saa711x_writeregs(sd, saa7113_init);
break;
default:
state->crystal_freq = SAA7115_FREQ_32_11_MHZ;
@@ -1771,6 +1877,10 @@ static int saa711x_probe(struct i2c_client *client,
}
if (state->ident > SAA7111A && state->ident != GM7113C)
saa711x_writeregs(sd, saa7115_init_misc);
+
+ if (pdata)
+ saa711x_write_platform_data(state, pdata);
+
saa711x_set_v4lstd(sd, V4L2_STD_NTSC);
v4l2_ctrl_handler_setup(hdl);
diff --git a/drivers/media/i2c/saa711x_regs.h b/drivers/media/i2c/saa711x_regs.h
index 70c56d1..730ca90 100644
--- a/drivers/media/i2c/saa711x_regs.h
+++ b/drivers/media/i2c/saa711x_regs.h
@@ -202,9 +202,24 @@
#define R_FF_S_PLL_MAX_PHASE_ERR_THRESH_NUM_LINES 0xff
/* SAA7113 bit-masks */
+#define SAA7113_R_08_HTC_OFFSET 3
+#define SAA7113_R_08_HTC_MASK (0x3 << SAA7113_R_08_HTC_OFFSET)
#define SAA7113_R_08_FSEL 0x40
#define SAA7113_R_08_AUFD 0x80
+#define SAA7113_R_10_VRLN_OFFSET 3
+#define SAA7113_R_10_VRLN_MASK (0x1 << SAA7113_R_10_VRLN_OFFSET)
+#define SAA7113_R_10_OFTS_OFFSET 6
+#define SAA7113_R_10_OFTS_MASK (0x3 << SAA7113_R_10_OFTS_OFFSET)
+
+#define SAA7113_R_12_RTS0_OFFSET 0
+#define SAA7113_R_12_RTS0_MASK (0xf << SAA7113_R_12_RTS0_OFFSET)
+#define SAA7113_R_12_RTS1_OFFSET 4
+#define SAA7113_R_12_RTS1_MASK (0xf << SAA7113_R_12_RTS1_OFFSET)
+
+#define SAA7113_R_13_ADLSB_OFFSET 7
+#define SAA7113_R_13_ADLSB_MASK (0x1 << SAA7113_R_13_ADLSB_OFFSET)
+
#if 0
/* Those structs will be used in the future for debug purposes */
struct saa711x_reg_descr {
diff --git a/include/media/saa7115.h b/include/media/saa7115.h
index 4079186..e8d512a 100644
--- a/include/media/saa7115.h
+++ b/include/media/saa7115.h
@@ -64,5 +64,69 @@
#define SAA7115_FREQ_FL_APLL (1 << 2) /* SA 3A[3], APLL, SAA7114/5 only */
#define SAA7115_FREQ_FL_DOUBLE_ASCLK (1 << 3) /* SA 39, LRDIV, SAA7114/5 only */
+/* ===== SAA7113 Config enums ===== */
+
+/* Register 0x08 "Horizontal time constant" [Bit 3..4]:
+ * Should be set to "Fast Locking Mode" according to the datasheet,
+ * and that is the default setting in the gm7113c_init table.
+ * saa7113_init sets this value to "VTR Mode". */
+enum saa7113_r08_htc {
+ SAA7113_HTC_TV_MODE = 0x00,
+ SAA7113_HTC_VTR_MODE, /* Default for saa7113_init */
+ SAA7113_HTC_FAST_LOCKING_MODE = 0x03 /* Default for gm7113c_init */
+};
+
+/* Register 0x10 "Output format selection" [Bit 6..7]:
+ * Defaults to ITU_656 as specified in datasheet. */
+enum saa7113_r10_ofts {
+ SAA7113_OFTS_ITU_656 = 0x0, /* Default */
+ SAA7113_OFTS_VFLAG_BY_VREF,
+ SAA7113_OFTS_VFLAG_BY_DATA_TYPE
+};
+
+/* Register 0x12 "Output control" [Bit 0..3 Or Bit 4..7]:
+ * This is used to select what data is output on the RTS0 and RTS1 pins.
+ * RTS1 [Bit 4..7] Defaults to DOT_IN. (This value can not be set for RTS0)
+ * RTS0 [Bit 0..3] Defaults to VIPB in gm7113c_init as specified
+ * in the datasheet, but is set to HREF_HS in the saa7113_init table. */
+enum saa7113_r12_rts {
+ SAA7113_RTS_DOT_IN = 0, /* OBS: Only for RTS1 (Default RTS1) */
+ SAA7113_RTS_VIPB, /* Default RTS0 For gm7113c_init */
+ SAA7113_RTS_GPSW,
+ SAA7115_RTS_HL,
+ SAA7113_RTS_VL,
+ SAA7113_RTS_DL,
+ SAA7113_RTS_PLIN,
+ SAA7113_RTS_HREF_HS, /* Default RTS0 For saa7113_init */
+ SAA7113_RTS_HS,
+ SAA7113_RTS_HQ,
+ SAA7113_RTS_ODD,
+ SAA7113_RTS_VS,
+ SAA7113_RTS_V123,
+ SAA7113_RTS_VGATE,
+ SAA7113_RTS_VREF,
+ SAA7113_RTS_FID
+};
+
+struct saa7115_platform_data {
+ /* saa7113 only: Force the use of the gm7113c_init table,
+ * instead of the old saa7113_init table. */
+ bool saa7113_force_gm7113c_init;
+
+ /* SAA7113/GM7113C Specific configurations */
+ enum saa7113_r08_htc *saa7113_r08_htc; /* [R_08 - Bit 3..4] */
+
+ bool *saa7113_r10_vrln; /* [R_10 - Bit 3]
+ Disabled for gm7113c_init
+ Enabled for saa7113c_init */
+ enum saa7113_r10_ofts *saa7113_r10_ofts; /* [R_10 - Bit 6..7] */
+
+ enum saa7113_r12_rts *saa7113_r12_rts0; /* [R_12 - Bit 0..3] */
+ enum saa7113_r12_rts *saa7113_r12_rts1; /* [R_12 - Bit 4..7] */
+
+ bool *saa7113_r13_adlsb; /* [R_13 - Bit 7]
+ Default disabled */
+};
+
#endif
--
1.8.3.1
^ permalink raw reply related [flat|nested] 5+ messages in thread