Re: [PATCH v4 9/9] arm64: dts: mediatek: Add Video Decoder for MT8173

[Tiffany Lin <tiffany.lin@mediatek.com>]

Hi Matthias,

On Thu, 2016-08-11 at 17:44 +0200, Matthias Brugger wrote:
> 
> On 10/08/16 16:48, Tiffany Lin wrote:
> > Add video decoder node for MT8173
> >
> > Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
> > ---
> >  arch/arm64/boot/dts/mediatek/mt8173.dtsi |   44 ++++++++++++++++++++++++++++++
> >  1 file changed, 44 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> > index 10f638f..2872cd7 100644
> > --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> > +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> > @@ -974,6 +974,50 @@
> >  			#clock-cells = <1>;
> >  		};
> >
> > +		vcodec_dec: vcodec@16000000 {
> > +			compatible = "mediatek,mt8173-vcodec-dec";
> > +			reg = <0 0x16000000 0 0x100>,	/* VDEC_SYS */
> > +			      <0 0x16020000 0 0x1000>,	/* VDEC_MISC */
> > +			      <0 0x16021000 0 0x800>,	/* VDEC_LD */
> > +			      <0 0x16021800 0 0x800>,	/* VDEC_TOP */
> > +			      <0 0x16022000 0 0x1000>,	/* VDEC_CM */
> > +			      <0 0x16023000 0 0x1000>,	/* VDEC_AD */
> > +			      <0 0x16024000 0 0x1000>,	/* VDEC_AV */
> > +			      <0 0x16025000 0 0x1000>,	/* VDEC_PP */
> > +			      <0 0x16026800 0 0x800>,	/* VDEC_HWD */
> > +			      <0 0x16027000 0 0x800>,	/* VDEC_HWQ */
> > +			      <0 0x16027800 0 0x800>,	/* VDEC_HWB */
> > +			      <0 0x16028400 0 0x400>;	/* VDEC_HWG */
> > +			interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_LOW>;
> > +			mediatek,larb = <&larb1>;
> > +			iommus = <&iommu M4U_PORT_HW_VDEC_MC_EXT>,
> > +				 <&iommu M4U_PORT_HW_VDEC_PP_EXT>,
> > +				 <&iommu M4U_PORT_HW_VDEC_AVC_MV_EXT>,
> > +				 <&iommu M4U_PORT_HW_VDEC_PRED_RD_EXT>,
> > +				 <&iommu M4U_PORT_HW_VDEC_PRED_WR_EXT>,
> > +				 <&iommu M4U_PORT_HW_VDEC_UFO_EXT>,
> > +				 <&iommu M4U_PORT_HW_VDEC_VLD_EXT>,
> > +				 <&iommu M4U_PORT_HW_VDEC_VLD2_EXT>;
> > +			mediatek,vpu = <&vpu>;
> > +			power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>;
> > +			clocks = <&apmixedsys CLK_APMIXED_VCODECPLL>,
> > +				 <&topckgen CLK_TOP_UNIVPLL_D2>,
> > +				 <&topckgen CLK_TOP_CCI400_SEL>,
> > +				 <&topckgen CLK_TOP_VDEC_SEL>,
> > +				 <&topckgen CLK_TOP_VCODECPLL>,
> > +				 <&apmixedsys CLK_APMIXED_VENCPLL>,
> > +				 <&topckgen CLK_TOP_VENC_LT_SEL>,
> > +				 <&topckgen CLK_TOP_VCODECPLL_370P5>;
> > +			clock-names = "vcodecpll",
> > +				      "univpll_d2",
> > +				      "clk_cci400_sel",
> > +				      "vdec_sel",
> > +				      "vdecpll",
> > +				      "vencpll",
> > +				      "venc_lt_sel",
> > +				      "vdec_bus_clk_src";
> > +		};
> > +
> 
> Shouldn't we set here:
> status = "disabled";
> 
> To save power on headless systems?
> 
We only power on when there is at least one decode instance created.
In this case, do we need "status = "disabled";" here?
I see some other device nodes in dtsi do not add this.
Sorry, I am just confused when should we add status for device node.


best regards,
Tiffany

> Regards,
> Matthias
> 
> >  		larb1: larb@16010000 {
> >  			compatible = "mediatek,mt8173-smi-larb";
> >  			reg = <0 0x16010000 0 0x1000>;
> >