From: Peter Meszmer <hubblest@web.de>
To: Matthias Schwarzott <zzam@gentoo.org>
Cc: linux-dvb@linuxtv.org
Subject: Re: [linux-dvb] AVerMedia DVB-S Hybrid+FM and DVB-S Pro [A700]
Date: Wed, 13 Feb 2008 11:05:49 +0100 [thread overview]
Message-ID: <200802131105.49910.hubblest@web.de> (raw)
In-Reply-To: <200802122206.30369.zzam@gentoo.org>
Am Dienstag, 12. Februar 2008 schrieben Sie:
> I added this to the wiki-page about A700:
> http://www.linuxtv.org/wiki/index.php/AVerMedia_AVerTV_DVB-S_Pro_(A700)
>
> Maybe we should rename the page to AverMedia_AverTV_DVB-S_A700 or anything
> similar.
>
> * Could you load saa7134 module of unpatched driver, but with parameter
> i2c_scan=1.
> * lspci -vvnn also should be interesting
> * If you have a camera, could you do a picture, so we can get info about
> the used analog tuner. I guess it is some XC30??. But to get it running you
> should contact video4linux mailinglist.
>
>
> Regards
> Matthias
Hello Matthias,
if I load the saa7134 module of unpatched driver, but with parameter
i2c_scan=1, dmesg shows (Kernel 2.6.24-gentoo-r2)
saa7130/34: v4l2 driver version 0.2.14 loaded
saa7133[0]: found at 0000:02:07.0, rev: 209, irq: 18, latency: 64, mmio:
0xd3024000
saa7133[0]: subsystem: 1461:a7a2, board: UNKNOWN/GENERIC [card=0,autodetected]
saa7133[0]: board init: gpio is 6da00
saa7133[0]: i2c eeprom 00: 61 14 a2 a7 ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c scan: found device @ 0x1c [???]
saa7133[0]: i2c scan: found device @ 0xa0 [eeprom]
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
and lspci -vvnn returns
02:07.0 Multimedia controller [0480]: Philips Semiconductors SAA7133/SAA7135
Video Broadcast Decoder [1131:7133] (rev d1)
Subsystem: Avermedia Technologies Inc Unknown device [1461:a7a2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (63750ns min, 63750ns max)
Interrupt: pin A Route to IRQ 18
Region 0: Memory at d3024000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=3 PME-
Kernel driver in use: saa7134
Kernel modules: saa7134
I did some pictures too... the link to them is in a PM for you. The analog
tuner seems to be a XC2028, but I don't see any possibilities to test the
tuner.
Regards
Peter
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
next prev parent reply other threads:[~2008-02-13 10:11 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-02-07 15:23 [linux-dvb] AVerMedia DVB-S Hybrid+FM and DVB-S Pro [A700] Eduard Huguet
2008-02-07 16:47 ` Peter Meszmer
2008-02-07 19:13 ` Matthias Schwarzott
2008-02-07 20:12 ` Eduard Huguet
2008-02-07 21:19 ` Peter Meszmer
2008-02-12 21:06 ` Matthias Schwarzott
2008-02-13 10:05 ` Peter Meszmer [this message]
2008-02-13 12:59 ` Matthias Schwarzott
-- strict thread matches above, loose matches on Subject: below --
2008-02-07 9:23 Peter Meszmer
2008-02-13 18:17 ` Matthias Schwarzott
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200802131105.49910.hubblest@web.de \
--to=hubblest@web.de \
--cc=linux-dvb@linuxtv.org \
--cc=zzam@gentoo.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox