From: Ales Jurik <ajurik@quick.cz>
To: linux-dvb@linuxtv.org
Subject: Re: [linux-dvb] Re : Re : No lock possible at some DVB-S2 channels with TT S2-3200/linux
Date: Sat, 21 Jun 2008 15:52:41 +0200 [thread overview]
Message-ID: <200806211552.41278.ajurik@quick.cz> (raw)
In-Reply-To: <200806211436.47765.dkuhlen@gmx.net>
Hi,
on the frequency you've mentioned I didn't have any problem (never). But at
lyngsat it is reported as 11914MHz. I never used freq. shifting (only
tested), it was not reasonable for me.
Problems I have are at transponders with 8PSK modulation.
Thanks and Best Regards,
Ales
On Saturday 21 of June 2008, Dominik Kuhlen wrote:
> Hi
>
> ------snip----
>
> > > Could you please try the attached patch if this fixes the problem with
> > > nominal frequency/symbolrate settings?
> >
> > Many thanks, but I don't see any improvement. Minimum time after I've
> > lock is 150s.
>
> Could you please check whether the reported frequency is sane:
> Example: 19.2°E 11915MHz H 27500 DVB-S2
>
> Test1: use the nominal frequency:
> ./simpledvbtune -f 11915 -d 2
> dvbfe setparams : delsys=4 1315.000MHz / Rate : 27500kSPS
> Status: 1b: Signal Carrier Sync Lock
> SNR: 0 44 (0x2c) (4.4dB)
> BER: 0 0 0 0 (0x0)
> Signal: 5 170 (0x5aa) 1450 (145.0dBm)
> Frontend: if=1313.627 MHz
>
> Test2: set positive offset (+3MHz):
> ./simpledvbtune -f 11918 -d 2
> dvbfe setparams : delsys=4 1318.000MHz / Rate : 27500kSPS
> Frontend: if=1313.660 MHz
> The frontend does automatically locks on the correct frequency
>
> Test3: set negative offset (-4MHz):
> ./simpledvbtune -f 11911 -d 2
> dvbfe setparams : delsys=4 1311.000MHz / Rate : 27500kSPS
> Frontend: if=1313.650 MHz
>
> Find lower limit:
> ./simpledvbtune -f 11896 -d 2 (does not work)
> ./simpledvbtune -f 11897 -d 2 (works 100%)
> dvbfe setparams : delsys=4 1297.000MHz / Rate : 27500kSPS
> Frontend: if=1313.654 MHz
>
> Find upper limit:
> ./simpledvbtune -f 11930 -d 2 (does not work)
> ./simpledvbtune -f 11929 -d 2 (works 100%)
> dvbfe setparams : delsys=4 1329.000MHz / Rate : 27500kSPS
> Frontend: if=1313.645 MHz
>
> Which means:
> - I can specify any frequency from 11896MHz to 11929MHz and get 100% lock
> success - and the Frontend (actually the derotator) reports the real
> frequency (e.g. for auto correcting the channels list)
>
> Cards I have tested so far:
> - pctv452e
> - mantis (Multimedia controller [0480]: Twinhan Technology Co. Ltd Mantis
> DTV PCI Bridge Controller [Ver 1.0] [1822:4e35] (rev 01) Subsystem: Twinhan
> Technology Co. Ltd Unknown device [1822:0031])
>
> Unfortunately I'm trapped behind a single-cable installation and have only
> access to 19.2°E Highband Horizontal
>
>
> Dominik
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
next prev parent reply other threads:[~2008-06-21 13:53 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-05-12 18:42 [linux-dvb] No lock possible at some DVB-S2 channels with TT S2-3200/linux Ales Jurik
2008-05-13 17:58 ` [linux-dvb] Re : " manu
2008-05-13 21:26 ` Ales Jurik
2008-05-13 22:01 ` [linux-dvb] Re : " manu
2008-05-22 8:13 ` Ales Jurik
2008-05-22 9:34 ` [linux-dvb] Re : Re : No lock possible at some DVB-S2 channelswith " Igor
2008-06-15 9:47 ` [linux-dvb] Re : Re : No lock possible at some DVB-S2 channels with " Dominik Kuhlen
2008-06-15 17:20 ` Ales Jurik
2008-06-16 2:21 ` [linux-dvb] Re : " manu
2008-06-16 8:20 ` Ales Jurik
2008-06-16 19:14 ` joep
2008-06-16 20:26 ` ChaosMedia > WebDev
2008-06-16 20:45 ` Ales Jurik
2008-06-20 13:18 ` Daniel
2008-06-20 13:47 ` Ales Jurik
2008-06-20 14:33 ` Daniel
2008-06-20 15:32 ` psofa
2008-06-20 15:45 ` joep
2008-06-21 12:36 ` [linux-dvb] " Dominik Kuhlen
2008-06-21 13:52 ` Ales Jurik [this message]
2008-06-21 16:40 ` Dominik Kuhlen
2008-06-21 17:20 ` Ales Jurik
2008-06-22 18:19 ` psofa
2008-06-26 19:58 ` Goga777
-- strict thread matches above, loose matches on Subject: below --
2008-06-15 19:31 psofa
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200806211552.41278.ajurik@quick.cz \
--to=ajurik@quick.cz \
--cc=linux-dvb@linuxtv.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox