* Kworld mpeg tv station / PCI [KW-TV878-FBKM]
@ 2008-08-17 13:27 litlle girl
2008-08-17 18:52 ` litlle girl
2008-08-17 21:22 ` Daniel Glöckner
0 siblings, 2 replies; 4+ messages in thread
From: litlle girl @ 2008-08-17 13:27 UTC (permalink / raw)
To: video4linux-list
Hi guys,
please help,
i try to make my tv card working on linux.
My tv card is: Kworld mpeg tv station / PCI [KW-TV878-FBKM]
Conexant Fusion 878A
My linux is: Kubuntu 8.10.
My problem is: when module bttv is loaded tv card turns audio on,
then i run tvtime audio is from tv channel,
and when i turn off tvtime audio remains,
mute isnt working
this is my /etc/modprobe.d/bttv
options bttv tuner=5 radio=1 pll=1 gpiomask=0x008007 audiomux=0,3,3,3,3
when i put: audiomux=3,3,3,3,3
when module bttv is loaded tv card turns audio on,
then i run tvtime, audio is muted [when i mute audio in tvtime - audio is
unmuted],
and when i turn off tvtime always turn on and audio remains,
What i do wrong??? Why Audio is always on, until i rmmod bttv??
i was testing
audiomux=0x000000,0x000001,0x000000,0x000000,0x000003
too.
Why Audiomu acceps only 5 values? At Sound-Faq there are 6 values.
Regards
LLG
--------------------------------------------------------------------------------------------
this car runs ok on xp,
this is my snif from xp:
### BtSpy Report ###
General information:
Name:Kworld bt878
Chip: Bt878 , Rev: 0x00
Subsystem: 0x00000000
Vendor: Gammagraphx, Inc.
Values to MUTE audio:
Mute_GPOE : 0x008007
Mute_GPDATA: 0x000003
Has TV Tuner: Yes
TV_Mux : 2
TV_GPOE : 0x008007
TV_GPDATA: 0x000000
Number of Composite Ins: 1
Composite in #1
Composite1_Mux : 3
Composite1_GPOE : 0x008007
Composite1_GPDATA: 0x000000
Has SVideo: Yes
SVideo_Mux : 1
SVideo_GPOE : 0x008007
SVideo_GPDATA: 0x000000
Has Radio: Yes
Radio_GPOE : 0x008007
Radio_GPDATA: 0x000001
Add here all the comments you want!
If your card can decode Stereo TV , and
your card does NOT use one of the following
chips, you will have to "peek" the right
GPDATA and GPOE values to enable Stereo and
SAP audio. The driver already supports the
DPL3518, MSP34xx, PT2254, TDA7432, TDA8425,
TDA9840, TDA9850, TDA9855, TDA9873, TDA9874,
TDA9875, TEA6300 and TEA6420 and does not require
extra information to drive them!
If you are able to get your card working using
this program , please , mail me this file (with
any extra comments you would like to add) to:
ejtagle@tutopia.com , so I can add native support
to your card in the next driver release!
--------------------------------------------------------------------------------------------
lspci -vv
00:0b.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ec001000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
--------------------------------------------------------------------------------------------
[ 230.747301] bttv0: unloading
[ 238.612345] bttv: driver version 0.9.17 loaded
[ 238.612354] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 238.612905] bttv: Bt8xx card found (0).
[ 238.612923] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32,
mmio: 0xec000000
[ 238.613257] bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
[ 238.613262] bttv0: gpio config override: mask=0x8007, mux=0x3,0x3,0x3,0x3
[ 238.613301] bttv0: gpio: en=00000000, out=00000000 in=003fffff [init]
[ 238.617865] All bytes are equal. It is not a TEA5767
[ 238.617872] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw])
[ 238.633870] tveeprom 1-0050: Huh, no eeprom present (err=-121)?
[ 238.633881] bttv0: tuner type=5
[ 238.634342] tuner-simple 1-0060: type set to 5 (Philips PAL_BG (FI1216
and compatibles))
[ 238.634348] tuner 1-0060: type set to Philips PAL_BG (FI1
[ 238.634694] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 238.635300] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 238.635975] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 238.651012] bttv0: registered device video0
[ 238.651344] bttv0: registered device vbi0
[ 238.651524] bttv0: registered device radio0
[ 238.651700] bttv0: PLL: 28636363 => 35468950 . ok
[ 238.670348] bt878: AUDIO driver version 0.0.0 loaded
[ 238.670404] bt878: Bt878 AUDIO function found (0).
[ 238.670423] ACPI: PCI Interrupt 0000:00:0b.1[A] -> GSI 19 (level, low) ->
IRQ 19
[ 238.670430] bt878_probe: card id=[0x0], Unknown card.
[ 238.670432] Exiting..
[ 238.670436] ACPI: PCI interrupt for device 0000:00:0b.1 disabled
[ 238.670444] bt878: probe of 0000:00:0b.1 failed with error -22
[ 314.583054] bttv0: unloading
[ 318.080455] bttv: driver version 0.9.17 loaded
[ 318.080464] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 318.081013] bttv: Bt8xx card found (0).
[ 318.081033] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32,
mmio: 0xec000000
[ 318.081409] bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
[ 318.081414] bttv0: gpio config override: mask=0x8003, mux=0x0,0x3,0x3,0x3
[ 318.081458] bttv0: gpio: en=00000000, out=00000000 in=003fffff [init]
[ 318.088073] All bytes are equal. It is not a TEA5767
[ 318.088084] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw])
[ 318.100242] tveeprom 1-0050: Huh, no eeprom present (err=-121)?
[ 318.100253] bttv0: tuner type=5
[ 318.100707] tuner-simple 1-0060: type set to 5 (Philips PAL_BG (FI1216
and compatibles))
[ 318.100713] tuner 1-0060: type set to Philips PAL_BG (FI1
[ 318.101052] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 318.101636] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 318.105850] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 318.118103] bttv0: registered device video0
[ 318.118442] bttv0: registered device vbi0
[ 318.118625] bttv0: registered device radio0
[ 318.118802] bttv0: PLL: 28636363 => 35468950 . ok
[ 330.146931] bt878: AUDIO driver version 0.0.0 loaded
[ 330.147334] bt878: Bt878 AUDIO function found (0).
[ 330.147354] ACPI: PCI Interrupt 0000:00:0b.1[A] -> GSI 19 (level, low) ->
IRQ 19
[ 330.147362] bt878_probe: card id=[0x0], Unknown card.
[ 330.147363] Exiting..
[ 330.147367] ACPI: PCI interrupt for device 0000:00:0b.1 disabled
[ 330.148097] bt878: probe of 0000:00:0b.1 failed with error -22
[ 361.965990] bttv0: unloading
[ 377.148325] bttv: driver version 0.9.17 loaded
[ 377.148334] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 377.148878] bttv: Bt8xx card found (0).
[ 377.148897] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32,
mmio: 0xec000000
[ 377.149226] bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
[ 377.149231] bttv0: gpio config override: mask=0x8005, mux=0x0,0x3,0x3,0x3
[ 377.149271] bttv0: gpio: en=00000000, out=00000000 in=003fffff [init]
[ 377.153726] All bytes are equal. It is not a TEA5767
[ 377.153732] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw])
[ 377.167665] tveeprom 1-0050: Huh, no eeprom present (err=-121)?
[ 377.167676] bttv0: tuner type=5
[ 377.168256] tuner-simple 1-0060: type set to 5 (Philips PAL_BG (FI1216
and compatibles))
[ 377.168262] tuner 1-0060: type set to Philips PAL_BG (FI1
[ 377.169440] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 377.170386] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 377.171291] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 377.184888] bttv0: registered device video0
[ 377.185228] bttv0: registered device vbi0
[ 377.185408] bttv0: registered device radio0
[ 377.185587] bttv0: PLL: 28636363 => 35468950 . ok
[ 387.438264] bt878: AUDIO driver version 0.0.0 loaded
[ 387.438658] bt878: Bt878 AUDIO function found (0).
[ 387.438678] ACPI: PCI Interrupt 0000:00:0b.1[A] -> GSI 19 (level, low) ->
IRQ 19
[ 387.438686] bt878_probe: card id=[0x0], Unknown card.
[ 387.438687] Exiting..
[ 387.438691] ACPI: PCI interrupt for device 0000:00:0b.1 disabled
[ 387.439381] bt878: probe of 0000:00:0b.1 failed with error -22
[ 407.393352] bttv0: unloading
[ 428.936140] bttv: Unknown parameter `bt878'
[ 432.501026] bttv: driver version 0.9.17 loaded
[ 432.501035] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 432.501598] bttv: Bt8xx card found (0).
[ 432.501617] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32,
mmio: 0xec000000
[ 432.501952] bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
[ 432.501956] bttv0: gpio config override: mask=0x8006, mux=0x0,0x3,0x3,0x3
[ 432.501996] bttv0: gpio: en=00000000, out=00000000 in=003fffff [init]
[ 432.506515] All bytes are equal. It is not a TEA5767
[ 432.506521] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw])
[ 432.520696] tveeprom 1-0050: Huh, no eeprom present (err=-121)?
[ 432.520706] bttv0: tuner type=5
[ 432.521765] tuner-simple 1-0060: type set to 5 (Philips PAL_BG (FI1216
and compatibles))
[ 432.521774] tuner 1-0060: type set to Philips PAL_BG (FI1
[ 432.522207] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 432.523811] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 432.525050] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 432.538845] bttv0: registered device video0
[ 432.539199] bttv0: registered device vbi0
[ 432.539379] bttv0: registered device radio0
[ 432.539554] bttv0: PLL: 28636363 => 35468950 . ok
[ 435.129046] bt878: AUDIO driver version 0.0.0 loaded
[ 435.129439] bt878: Bt878 AUDIO function found (0).
[ 435.129459] ACPI: PCI Interrupt 0000:00:0b.1[A] -> GSI 19 (level, low) ->
IRQ 19
[ 435.129467] bt878_probe: card id=[0x0], Unknown card.
[ 435.129469] Exiting..
[ 435.129473] ACPI: PCI interrupt for device 0000:00:0b.1 disabled
[ 435.130120] bt878: probe of 0000:00:0b.1 failed with error -22
[ 449.992705] bttv0: unloading
[ 470.501313] bttv: driver version 0.9.17 loaded
[ 470.501322] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 470.501863] bttv: Bt8xx card found (0).
[ 470.501882] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32,
mmio: 0xec000000
[ 470.502212] bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
[ 470.502217] bttv0: gpio config override: mask=0x8001, mux=0x0,0x3,0x3,0x3
[ 470.502257] bttv0: gpio: en=00000000, out=00000000 in=003fffff [init]
[ 470.506713] All bytes are equal. It is not a TEA5767
[ 470.506719] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw])
[ 470.520910] tveeprom 1-0050: Huh, no eeprom present (err=-121)?
[ 470.520921] bttv0: tuner type=5
[ 470.521854] tuner-simple 1-0060: type set to 5 (Philips PAL_BG (FI1216
and compatibles))
[ 470.521863] tuner 1-0060: type set to Philips PAL_BG (FI1
[ 470.522327] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 470.523922] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 470.525105] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 470.539267] bttv0: registered device video0
[ 470.539599] bttv0: registered device vbi0
[ 470.539978] bttv0: registered device radio0
[ 470.540218] bttv0: PLL: 28636363 => 35468950 . ok
[ 470.563604] bt878: AUDIO driver version 0.0.0 loaded
[ 470.563669] bt878: Bt878 AUDIO function found (0).
[ 470.563689] ACPI: PCI Interrupt 0000:00:0b.1[A] -> GSI 19 (level, low) ->
IRQ 19
[ 470.563696] bt878_probe: card id=[0x0], Unknown card.
[ 470.563698] Exiting..
[ 470.563702] ACPI: PCI interrupt for device 0000:00:0b.1 disabled
[ 470.563711] bt878: probe of 0000:00:0b.1 failed with error -22
[ 485.253612] bttv0: unloading
[ 493.269669] bttv: driver version 0.9.17 loaded
[ 493.269679] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 493.270218] bttv: Bt8xx card found (0).
[ 493.270237] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32,
mmio: 0xec000000
[ 493.270571] bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
[ 493.270576] bttv0: gpio config override: mask=0x8007, mux=0x0,0x3,0x3,0x3
[ 493.270615] bttv0: gpio: en=00000000, out=00000000 in=003fffff [init]
[ 493.275346] All bytes are equal. It is not a TEA5767
[ 493.275353] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw])
[ 493.289066] tveeprom 1-0050: Huh, no eeprom present (err=-121)?
[ 493.289077] bttv0: tuner type=5
[ 493.290065] tuner-simple 1-0060: type set to 5 (Philips PAL_BG (FI1216
and compatibles))
[ 493.290074] tuner 1-0060: type set to Philips PAL_BG (FI1
[ 493.290508] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 493.292420] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 493.293624] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 493.307847] bttv0: registered device video0
[ 493.308180] bttv0: registered device vbi0
[ 493.308360] bttv0: registered device radio0
[ 493.308534] bttv0: PLL: 28636363 => 35468950 . ok
[ 498.395945] bt878: AUDIO driver version 0.0.0 loaded
[ 498.396387] bt878: Bt878 AUDIO function found (0).
[ 498.396407] ACPI: PCI Interrupt 0000:00:0b.1[A] -> GSI 19 (level, low) ->
IRQ 19
[ 498.396415] bt878_probe: card id=[0x0], Unknown card.
[ 498.396417] Exiting..
[ 498.396421] ACPI: PCI interrupt for device 0000:00:0b.1 disabled
[ 498.397065] bt878: probe of 0000:00:0b.1 failed with error -22
[ 1936.564357] bttv0: unloading
[ 1942.442190] bttv: driver version 0.9.17 loaded
[ 1942.442199] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 1942.442815] bttv: Bt8xx card found (0).
[ 1942.442834] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32,
mmio: 0xec000000
[ 1942.443313] bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
[ 1942.443318] bttv0: gpio config override: mask=0x8007, mux=0x3,0x3,0x3,0x3
[ 1942.443358] bttv0: gpio: en=00000000, out=00000000 in=003fffff [init]
[ 1942.449662] All bytes are equal. It is not a TEA5767
[ 1942.449671] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw])
[ 1942.463279] tveeprom 1-0050: Huh, no eeprom present (err=-121)?
[ 1942.463290] bttv0: tuner type=5
[ 1942.463810] tuner-simple 1-0060: type set to 5 (Philips PAL_BG (FI1216
and compatibles))
[ 1942.463817] tuner 1-0060: type set to Philips PAL_BG (FI1
[ 1942.464147] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 1942.465204] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 1942.466099] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 1942.481559] bttv0: registered device video0
[ 1942.481893] bttv0: registered device vbi0
[ 1942.482070] bttv0: registered device radio0
[ 1942.482243] bttv0: PLL: 28636363 => 35468950 . ok
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: Kworld mpeg tv station / PCI [KW-TV878-FBKM]
2008-08-17 13:27 Kworld mpeg tv station / PCI [KW-TV878-FBKM] litlle girl
@ 2008-08-17 18:52 ` litlle girl
2008-08-17 21:22 ` Daniel Glöckner
1 sibling, 0 replies; 4+ messages in thread
From: litlle girl @ 2008-08-17 18:52 UTC (permalink / raw)
To: video4linux-list
[-- Attachment #1: Type: text/plain, Size: 99 bytes --]
Hi,
this are inf files from orginal windows cd driver disc.
I hope it will be usefull.
Yours,
LLG
[-- Attachment #2: bttuner.inf.tar.gz --]
[-- Type: application/x-gzip, Size: 3362 bytes --]
[-- Attachment #3: Type: text/plain, Size: 164 bytes --]
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Kworld mpeg tv station / PCI [KW-TV878-FBKM]
2008-08-17 13:27 Kworld mpeg tv station / PCI [KW-TV878-FBKM] litlle girl
2008-08-17 18:52 ` litlle girl
@ 2008-08-17 21:22 ` Daniel Glöckner
2008-08-18 19:39 ` litlle girl
1 sibling, 1 reply; 4+ messages in thread
From: Daniel Glöckner @ 2008-08-17 21:22 UTC (permalink / raw)
To: litlle girl; +Cc: video4linux-list
On Sun, Aug 17, 2008 at 03:27:38PM +0200, litlle girl wrote:
> mute isnt working
> this is my /etc/modprobe.d/bttv
> options bttv tuner=5 radio=1 pll=1 gpiomask=0x008007 audiomux=0,3,3,3,3
Unfortunately it is not possible to set the GPIO mute mask directly with
module parameters.
Try
options bttv card=5 tuner=5 radio=1 pll=1 gpiomask=0x8007 audiomux=0,1,0,0
This card should get a card entry in bttv-cards.c
> Why Audiomu acceps only 5 values? At Sound-Faq there are 6 values.
In fact it accepts only 4 values
- TV Tuner
- Radio
- External connector
- Internal connector
Daniel
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-08-18 19:40 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-08-17 13:27 Kworld mpeg tv station / PCI [KW-TV878-FBKM] litlle girl
2008-08-17 18:52 ` litlle girl
2008-08-17 21:22 ` Daniel Glöckner
2008-08-18 19:39 ` litlle girl
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox