From: Simon MORIN <simon.g.morin@gmail.com>
To: linux-dvb@linuxtv.org
Subject: [linux-dvb] WinTV HVR 1700 cannot scan (DVB-T)
Date: Wed, 26 Nov 2008 12:18:48 +0100 [thread overview]
Message-ID: <200811261218.49367.simon.g.morin@gmail.com> (raw)
[-- Attachment #1.1: Type: text/plain, Size: 8515 bytes --]
Hello everyone !
I have a problem with a WinTV HVR 1700
I installed the latest available driver via mercurial and the firmware (dvb-fe-
tda10048-1.0.fw).
The card seems to be well detected by its module (cx23885) as you can see in
the dmesg output.
I saw there [1] that some others firmware were used (v4l-cx23885-avcore-01.fw
and v4l-cx23885-enc.fw). I installed them, but I don't see when they are
loaded.
I am sure of the frequencies I used because I have successfully tested on the
same antenna, with the same frequencies with a WinTV Nova-T.
I do not see where the problem can come from.
[1] http://marc.info/?l=linux-dvb&m=120951119026705&w=2
Thank you very much for any help.
Simon MORIN
------
dmesg output :
Linux video capture interface: v2.00
cx23885 driver version 0.0.1 loaded
ACPI: PCI Interrupt 0000:0e:00.0[A] -> GSI 17 (level, low) -> IRQ 17
cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe bridge type 885
cx23885[0]/0: cx23885_init_tsport(portno=2)
CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700
[card=8,autodetected]
cx23885[0]/0: cx23885_pci_quirks()
cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 0x0
cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 0x0
cx23885[0]/0: cx23885_reset()
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [VID A]
cx23885[0]/0: cx23885_sram_channel_setup() 0x000104c0 <- 0x00000040
cx23885[0]/0: cx23885_sram_channel_setup() 0x000104d0 <- 0x00000b80
cx23885[0]/0: cx23885_sram_channel_setup() 0x000104e0 <- 0x000016c0
cx23885[0]/0: [bridge 885] sram setup VID A: bpl=2880 lines=3
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2]
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS1 B]
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010580 <- 0x00005000
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010590 <- 0x000052f0
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105a0 <- 0x000055e0
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105b0 <- 0x000058d0
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105c0 <- 0x00005bc0
cx23885[0]/0: [bridge 885] sram setup TS1 B: bpl=752 lines=5
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4]
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5]
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS2 C]
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105e0 <- 0x00006000
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105f0 <- 0x000062f0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010600 <- 0x000065e0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010610 <- 0x000068d0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010620 <- 0x00006bc0
cx23885[0]/0: [bridge 885] sram setup TS2 C: bpl=752 lines=5
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7]
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8]
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9]
cx23885[0]: i2c scan: found device @ 0x10 [tda10048]
cx23885[0]: i2c scan: found device @ 0xa0 [eeprom]
cx23885[0]: i2c scan: found device @ 0x84 [tda8295]
cx25840' 2-0044: cx25 0-21 found @ 0x88 (cx23885[0])
cx23885[0]: i2c scan: found device @ 0x66 [???]
cx23885[0]: i2c scan: found device @ 0x88 [cx25837]
cx23885[0]: i2c scan: found device @ 0x98 [???]
tveeprom 0-0050: Hauppauge model 81519, rev B2E9, serial# 3473167
tveeprom 0-0050: MAC address is 00-0D-FE-34-FF-0F
tveeprom 0-0050: tuner model is Philips 18271_8295 (idx 149, type 54)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB
Digital (eeprom 0xf4)
tveeprom 0-0050: audio processor is CX23885 (idx 39)
tveeprom 0-0050: decoder processor is CX23885 (idx 33)
tveeprom 0-0050: has no radio
cx23885[0]: hauppauge eeprom: model=81519
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
tda829x 1-0042: type set to tda8295
tda18271 1-0060: creating new instance
TDA18271HD/C1 detected @ 1-0060
DVB: registering new adapter (cx23885[0])
DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)...
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:0e:00.0, rev: 2, irq: 17, latency: 0, mmio:
0xfde00000
PCI: Setting latency timer of device 0000:0e:00.0 to 64
tda10048_firmware_upload: waiting for firmware upload (dvb-fe-
tda10048-1.0.fw)...
firmware: requesting dvb-fe-tda10048-1.0.fw
tda10048_firmware_upload: firmware read 24878 bytes.
tda10048_firmware_upload: firmware uploading
tda10048_firmware_upload: firmware uploaded
-----
Modules loaded :
#$ modprobe -v cx23885
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/tveeprom.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/btcx-
risc.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/videobuf-core.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/dvb/dvb-
core/dvb-core.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/videobuf-dvb.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/videobuf-dma-sg.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/cx2341x.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/v4l2-
compat-ioctl32.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/v4l1-
compat.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/videodev.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/cx23885/cx23885.ko debug=5 i2c_scan=1
[-- Attachment #1.2: Type: text/html, Size: 23695 bytes --]
[-- Attachment #2: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
reply other threads:[~2008-11-26 11:19 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200811261218.49367.simon.g.morin@gmail.com \
--to=simon.g.morin@gmail.com \
--cc=linux-dvb@linuxtv.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox